2008d02f4d
runtime: use different default IP and MAC for different kinds of boards
...
This helps reduce conflicts when having many boards on a development network.
2018-08-07 10:30:50 +08:00
bbe36b94f7
ad9154: enable sync in init
2018-08-06 19:02:27 +08:00
7f0b2ff594
jesd204sync: work around HMC7043 poor behavior with combined delays
...
The HMC7043 outputs poorly controlled signals when adjusting
two delays at once. This commit puts the DAC in one-shot SYSREF mode,
and only triggers synchronizations when SYSREF is stable.
2018-08-06 17:43:17 +08:00
f32f0126e2
Revert "ad9154: use continuous sync mode"
...
The HMC7043 is not really glitchless.
This reverts commit bd968211de
2018-08-06 16:59:53 +08:00
bd968211de
ad9154: use continuous sync mode
2018-08-06 00:27:10 +08:00
e83ee3a07a
hmc7043: disable GTP_CLK1 when not in use
...
Termination and biasing are not active at the FPGA when IBUFDS_GTE3 is
not instantiated, and driving a clock then leads to overvoltage.
2018-08-03 10:03:52 +08:00
6fc8439399
tweak moninj to allow old dashboard with new firmware
2018-08-02 19:34:14 +08:00
47740c8930
share moninj injection state between dashboards
...
Previously if one dashboard overrode a channel this was not visible on
any other dashboard - the channel appeared to operate normally.
2018-08-02 19:34:14 +08:00
whitequark
5871d13da8
firmware: actually compact in config::compact().
...
Fixes #1116 .
2018-08-01 16:27:48 +00:00
e4d48a78eb
drtio: wait for remote to ack TSC synchronization
...
Sayma takes a long time after TSC sync to align SYSREF, and this caused two issues:
1. Aux packets getting lost and causing error reports
2. DRTIO links reported up and kernels proceeding despite the DACs not being properly synced.
2018-07-26 20:28:17 +08:00
83de8b2ba2
drtio: add ping timeout during link init
2018-07-26 20:27:53 +08:00
446f791180
firmware: simplify SYSREF DRTIO alignment
2018-07-26 19:37:59 +08:00
f8c17528e7
satman: use new SYSREF code
2018-07-26 16:26:57 +08:00
32c95ac034
sayma: automated DAC SYSREF phase calibration
2018-07-26 16:23:55 +08:00
dbcf2fe9b4
firmware: remove 'chip found' messages on Sayma
2018-07-26 16:07:37 +08:00
d523d03f71
sayma: automated FPGA SYSREF phase offset calibration
2018-07-26 14:53:28 +08:00
0a9d3638ee
config: add write_int
2018-07-26 14:49:32 +08:00
19c51c644e
grabber: cleanup GRABBER_STATE
2018-07-24 19:08:51 +08:00
e71cbe53a6
firmware: cleanup Cargo.lock
2018-07-18 10:37:43 +08:00
13984385a8
firmware: version → ident
2018-07-15 17:40:17 +08:00
b27fa8964b
add variant in identifier string
...
Also add without-sawg suffixes on Sayma.
Closes #1060
Closes #1059
2018-07-15 17:21:17 +08:00
46fb5adac3
grabber: fix frequency counter formula
2018-07-12 20:14:38 +08:00
82def6b535
grabber: add frequency counter
...
Cameras are a bit obscure about what they output, this can help with troubleshooting.
2018-07-12 17:05:18 +08:00
29c35ee553
hmc7043: fix dumb mistake in previous commit
2018-07-12 13:01:41 +08:00
8802b930de
hmc7043: add delay after init
...
Delay required at step 9 of the "Typical Programming Sequence" (page 24 of the datasheet)
2018-07-12 12:37:12 +08:00
c66f9483f8
hmc7043: wait after changing delays
...
Allows for the SPI transaction to finish, and for the delay to stabilize.
2018-07-12 12:33:53 +08:00
1c191a62bf
sayma: tune SYSREF phases
2018-07-12 12:33:35 +08:00
773240bef4
hmc7043: test GPO before using
...
Based on code by David.
2018-07-12 11:30:24 +08:00
4843832329
hmc7043: check phase status on init. Closes #1055
...
Troubleshooting by David.
2018-07-11 19:45:24 +08:00
9397fa7f5a
hmc7043: unstick SYSREF FSM ( #1055 )
...
Troubleshooting by David.
Additionally, register 7D is broken.
Checking phase init state has to be done through another means.
2018-07-11 19:11:01 +08:00
4f56710e4b
grabber: add parser, report detected frame size in core device log
2018-07-10 02:06:37 +08:00
4eb26c0050
hmc7043: enable group 5
2018-07-03 14:16:31 +02:00
729ce58f98
sayma: use GTP_CLK1 to clock DRTIO satellite transceiver
...
This is required to get constant skew between the DRTIO transceiver clock
(which then generates the RTIO clock) and the siphaser reference clock.
Both the Si5324 and the RTM clock tree have non-deterministic in-to-out skew
at 150MHz due to dividers.
2018-06-28 11:23:40 +08:00
a65721d649
sayma: put RTM clock tree into the siphaser loop
...
* Fixes one bug where siphaser was one Si5324 output and the rest of the
system was clocked by the other. With the Si5324 settings we have, skew
between the outputs is not controlled.
* Puts the coaxial cable between AMC and RTM into the siphaser loop.
2018-06-27 21:46:55 +08:00
d49716dfac
satman: tune Sayma SYSREF phases
2018-06-27 18:09:35 +08:00
46c044099c
hmc7043,satman: verify alignment of SYSREF slips
2018-06-27 17:36:13 +08:00
7dfd70c502
hmc7043: make margin_{minus,plus} consistent with ad9154
2018-06-27 17:35:26 +08:00
4bbdd43bdf
hmc7043: do not freeze if SYSREF slip fails
2018-06-27 17:32:56 +08:00
a8a2ad68d3
runtime: tune Sayma SYSREF phases
2018-06-27 17:31:29 +08:00
84b3d9ecc6
bootloader: also check firmware CRC in SDRAM ( #1065 )
2018-06-23 11:28:12 +08:00
68530fde07
sayma: generate 100MHz from Si5324 on standalone and master targets
...
* Allow switching between DRTIO satellite and standalone without
touching the hardware.
* Allow operating standalone and master without an additional RF
signal generator.
2018-06-23 10:44:38 +08:00
whitequark
b6dd9c8bb0
runtime: support builds without RTIO DMA.
...
Fixes #1079 .
2018-06-23 00:56:21 +00:00
76fc63bbf7
jesd204: use separate controls for reset and input buffer disable
2018-06-22 11:38:18 +08:00
de7d64d482
sayma: clock JESD204 from GTP CLK2
...
This frees up GTP CLK1, which is routable to the SFP quads, for DRTIO.
2018-06-21 22:33:53 +08:00
07bcdfd91e
hmc7043: stricter check of FPGA SYSREF margin
2018-06-21 22:26:49 +08:00
e29536351d
drtio: resync SYSREF when TSC is loaded
2018-06-21 17:00:32 +08:00
5a2a857a2f
firmware: clean up SYSREF phase management
2018-06-21 16:23:41 +08:00
05e908a0fd
hmc7043: align SYSREF with RTIO
2018-06-21 15:54:42 +08:00
9741654cad
hmc7043: style
2018-06-21 15:54:42 +08:00
45e8263208
hmc7043: do not configure phases during initial init
...
They are determined later on.
2018-06-21 15:54:42 +08:00
whitequark
7cc3da4faf
firmware: do not lose the ".dirty" suffix in build versions.
...
Fixes #1074 .
2018-06-21 05:18:51 +00:00
whitequark
095ee28fd9
runtime: fix size values for bytes and bytearray RPCs.
...
Fixes #1076 .
2018-06-21 00:51:56 +00:00
814d0583db
hmc7043: improve smoothness of sysref phase control
2018-06-20 17:40:48 +08:00
5272c11704
typo
2018-06-20 17:05:20 +08:00
0c32d07e8b
ad9154: new sysref scan
...
Print margins around the pre-defined fixed phase.
Also report error if margins are too small.
The fixed phase is also changed by this commit (the value 88 is
from before the new HMC7043 initialization code, and is probably wrong).
2018-06-20 00:15:58 +08:00
3d0e92aefd
hmc7043: check that chip is disabled at startup
2018-06-19 23:49:17 +08:00
740e6863c3
hmc7043: add delay after releasing hardware reset
2018-06-19 23:48:48 +08:00
75b6cea52f
sayma: add SAWG to DRTIO satellite
2018-06-19 19:12:10 +08:00
eb3259b847
firmware: reduce number of DAC initialization attempts
...
Faster startup when one DAC is broken.
2018-06-19 19:10:23 +08:00
1d594d0c97
firmware: make DAC initialization failures non-fatal
...
This allows using RTMs with one broken DAC for development.
2018-06-19 19:09:38 +08:00
158b5e3083
satman: program Allaki
2018-06-19 18:09:05 +08:00
574892a4e5
firmware/serwb: cleanup and improve messaging
2018-06-19 15:11:03 +08:00
c862471165
typo
2018-06-19 14:35:24 +08:00
433273dd95
sayma: support RTM FPGA, HMC830 and HMC7043 in DRTIO master and satellite
2018-06-19 14:33:48 +08:00
476cfa0f53
si5324: improve lock messaging
2018-06-19 14:29:57 +08:00
d29b3dd588
hmc830: compile-time configurable reference frequency
2018-06-19 13:47:32 +08:00
0e640a6d6f
hmc7043: fix SYSREF to meet s/h at FPGA ( #794 )
2018-06-18 17:04:12 +08:00
6272052d15
ad9154: don't drive the bsm with txen pins
2018-06-18 10:04:42 +02:00
4f0c918dd3
slave_fpga: improve messaging
2018-06-17 00:27:27 +08:00
40baa8ecba
hmc7043: disable ch 10 and 11 group
2018-06-15 15:34:31 +00:00
edfae3c4ba
hmc7043: make fpga fabric clocks lvds
...
2 V common and 1.9 Vpp swing
is brutal to the banks (HP 1.8V AMC and RT 1.8V RTM)
2018-06-15 14:24:33 +00:00
f385add8b1
slave_fpga: disable cclk and din drive when done
...
to guard against accidental contention (old rtm gateware
but #813 rework done)
2018-06-13 16:26:48 +00:00
a9a25f2605
sayma_rtm: drive ref_lo_clk_sel, and set clk muxes early
2018-06-12 20:00:12 +02:00
Thomas Harty
b90a8fcc82
Merge branch 'master' of https://github.com/m-labs/artiq
2018-06-12 14:55:22 +01:00
ion
28ecf81c6c
Sayma: HMC7043 init and detect no longer need results.
2018-06-12 13:10:26 +01:00
ion
c8935f7adf
Sayma: bypass dividers where possible to minimize noise (nb this changes the output skew).
2018-06-12 12:56:04 +01:00
hartytp
7a0140ecb2
Sayma HMC830: update interface and register writes. ( #1068 )
...
* Break the HMC830 init into separate functions for general purpose (but, integer-N) init, setting dividers and checking lock
* Use 1.6mA ICP (which the loop filter was optimized for)
* Go through the data sheet carefully and set all registers to the correct value (e.g. ensure that all settings are correctly optimized for integer-N usage)
* Change divider values (now using 100MHz PFD, which should give lower noise in theory)
2018-06-12 12:37:17 +01:00
a9d97101fc
slave_fpga: add another check
2018-06-12 10:24:04 +02:00
a143e238a8
savel_fpga: get rid of unneeded config
2018-06-12 10:24:04 +02:00
4912f53ab4
slave_fpga: board_misoc
2018-06-12 10:24:04 +02:00
hartytp
cb6e44b23a
Sayma: disable unused HMC7043 outputs.
2018-06-12 16:18:20 +08:00
af88c4c93e
clean up hmc7043 reset
2018-06-05 20:41:48 +08:00
Thomas Harty
988054f4bb
Sayma: fix mistake in HMC7043 init code.
2018-06-05 19:22:04 +08:00
Thomas Harty
bd1ac7cf3b
Configure HMC7043 to give deterministic phase differences between its outputs
2018-06-05 19:22:04 +08:00
Thomas Harty
ac5c4913ec
Sayma RTM: hold hmc7043 in reset/mute state during init.
2018-06-05 19:22:04 +08:00
Florent Kermarrec
b82158a2de
firmware/ad9154: add stpl test
2018-06-05 02:08:57 +02:00
Florent Kermarrec
925b47b077
firmware/ad9154: reset the dac between each configuration attempt
2018-06-04 14:03:26 +02:00
whitequark
d686d33093
runtime: print hex dumps around PC/EA in case of exception.
...
For #1026 .
2018-06-01 21:17:59 +00:00
whitequark
2e09307d8d
firmware: use writeln instead of write in UART logger.
2018-05-29 03:16:52 +00:00
560889372f
firmware: grabber support
2018-05-29 10:26:36 +08:00
b860302a9a
firmware: fix typo in UART logger
2018-05-28 17:25:23 +00:00
whitequark
2b7d98eb04
firmware: enable all log levels when creating UART logger.
...
The default is all off.
2018-05-28 16:49:25 +00:00
Florent Kermarrec
bcb9c3d09d
firmware/serwb: move prbs_test outside of wait_init, add wishbone_test
2018-05-24 16:53:47 +02:00
Florent Kermarrec
353767bfdb
firmware/hmc830: add VCO subsystem register 6 programming (suggested by hartytp, tested on hardware without regression)
2018-05-24 16:49:49 +02:00
Florent Kermarrec
ad89c42acc
firmware/serwb: automatically adjust prbs test delay to prbs test cycles, increase prbs test cycles
2018-05-24 10:20:55 +02:00
Florent Kermarrec
19e5280824
firmware/ad9154: cleanup DAC init
...
- Split dac_setup in dac_reset, dat_detect & dac_setup.
- Only do one reset/detection.
- Configure before doing SYSREF scan (otherwise scan don't work at the first scan after power up).
- Do the spi_setup in each function.
2018-05-24 09:34:00 +02:00
Florent Kermarrec
fa3b48737b
firmware/hmc830: Added magic word to HMC830 init sequence (from gkasprow & marmeladapk)
2018-05-24 09:23:00 +02:00
b10d3ee4b4
make RTIO clock switch optional and simplify
...
Kasli no longer has an internal RTIO clock.
Switching clocks dynamically is no longer supported.
2018-05-18 17:41:34 +08:00
whitequark
5744d97d59
firmware: adjust backtrace addresses correctly.
2018-05-17 08:13:55 +00:00
d4f074b1e1
firmware: fix Allaki addressing. Closes #993
2018-05-17 16:02:21 +08:00
whitequark
31c6c79204
firmware: implement an edge profiler.
...
It doesn't work extremely well, and the results can be somewhat
confusing, and it needs a libunwind patch, but it's the best I could
do and it seems still useful.
2018-05-16 21:53:53 +00:00
a640041844
firmware: improve ad9154/hmc830/hmc7043 messaging
2018-05-16 23:15:17 +08:00
fedf7f0c87
firmware/ad9154: cleanup sysref scan and run everytime
2018-05-16 23:01:19 +08:00
1364cd2948
firmware/hmc830_7043: break out HMC830 SPI mode selection
2018-05-16 22:46:45 +08:00
0aadd3a361
firmware/hmc830_7043: improve messaging
2018-05-16 22:46:45 +08:00
whitequark
4d06c1d84b
coredevice.CommKernel: modernize. NFC.
2018-05-16 14:40:14 +00:00
whitequark
ca93b94aea
firmware: move config requests to management protocol.
...
They were only in session protocol because of historical reasons.
2018-05-16 14:32:49 +00:00
Florent Kermarrec
7fe49a78d2
firmware/runtime/session: fix compilation when no rtio core
2018-05-15 23:47:47 +02:00
whitequark
8128a814f6
firmware: update dependencies.
2018-05-15 18:17:32 +00:00
whitequark
1b0384c513
firmware: fix satman build.
2018-05-15 16:35:05 +00:00
whitequark
07b713fdad
firmware: use upstream log_buffer.
2018-05-15 15:19:20 +00:00
whitequark
9f5b76253c
firmware: remove some unnecessary unwraps.
2018-05-15 15:05:19 +00:00
whitequark
e5796e26e1
firmware: remove unused #![feature(untagged_unions)].
2018-05-15 15:05:19 +00:00
whitequark
b54926134c
firmware: update the signature of #[lang="panic_fmt"].
2018-05-15 15:05:19 +00:00
Florent Kermarrec
c18a73d45f
sayma_amc/rtm: use new serwb low-speed phy
2018-05-15 16:40:50 +02:00
whitequark
9347f6e00c
firmware: use a dedicated error type in the scheduler.
...
After this commit, error handling does not normally allocate
(session::Error::{Load,Unexpected} still allocate, but those two
are very rare).
Good riddance to libstd_artiq.
2018-05-15 14:19:44 +00:00
whitequark
479cb9a857
firmware: use dedicated error types for every protocol and thread.
...
Good riddance to io::Error::Unrecognized.
2018-05-15 13:27:23 +00:00
whitequark
514eab3d39
Update Rust to 1.26.0.
2018-05-15 12:47:51 +00:00
whitequark
26faaad2b7
firmware: remove io::Result<T, E> in favor of Result<T, impl Fail>.
...
This doesn't yet use impl Fail since std_artiq::io::Error doesn't
impl it.
2018-05-15 08:29:03 +00:00
whitequark
140ca729aa
firmware: rename io::Error::{UnexpectedEof→UnexpectedEnd}.
...
We don't even have files.
2018-05-15 08:27:45 +00:00
whitequark
ce0593315b
firmware: move {ProtoRead,ProtoWrite} to the root of libio.
2018-05-15 08:16:09 +00:00
whitequark
4416c04ae1
firmware: use the failure crate in libio.
2018-05-15 07:40:13 +00:00
whitequark
9e8f8bb669
firmware: extract io::Cursor into its own file.
...
Also remove unused io::CursorError.
2018-05-15 06:24:04 +00:00
whitequark
a4ab236af3
firmware: simplify some uses.
2018-05-14 19:24:14 +00:00
whitequark
d93aa13fd6
firmware: use upstream compiler_builtins again.
...
I've fixed i128 in LLVM, so there is no need in our fork anymore.
2018-05-14 19:11:57 +00:00
whitequark
5ead27f2e1
firmware: eliminate uses of std_artiq::io::{Read,Write} from runtime.
2018-05-14 19:11:57 +00:00
whitequark
cf33ba748d
firmware: eliminate non-io uses of std_artiq from runtime.
...
Just replace these with references to alloc.
2018-05-14 19:11:57 +00:00
whitequark
ae50196186
firmware: rename libproto to libproto_artiq.
...
libproto_artiq only has ARTIQ-specific protocols.
2018-05-14 18:09:44 +00:00
whitequark
02b8426f60
firmware: rename libboard to libboard_misoc.
...
By analogy with libbuild_misoc. Hopefully one day it actually gets
moved to misoc...
2018-05-14 18:09:44 +00:00
whitequark
1ff42683d9
firmware: merge libamp into libboard_artiq.
...
All gateware interfaces live in libboard_artiq, but libamp predates
libboard_artiq.
2018-05-14 17:33:25 +00:00
whitequark
764386c9e3
firmware: split libdrtioaux into libproto and libboard_artiq modules.
...
All other protocol code lives in libproto, and all other gateware
interfaces live in libboard_artiq.
2018-05-14 17:26:59 +00:00
whitequark
6a10d54432
firmware: migrate rpc_proto to new libio.
...
This closes an old and horrible issue in that some code in ksupport
may implicitly try to allocate and we'll never know until it crashes
at runtime inside liballoc_stub.
This also removes liballoc_stub.
This also removes ReadExt and WriteExt from libproto.
Hooray!
2018-05-14 17:26:59 +00:00
whitequark
09617c9f5e
firmware: migrate session_proto to new libio.
2018-05-14 15:17:32 +00:00
whitequark
e9c88e32e6
firmware: migrate moninj_proto to new libio.
2018-05-14 15:17:32 +00:00
whitequark
e292c8ab65
firmware: migrate mgmt_proto to new libio.
2018-05-14 15:17:32 +00:00
whitequark
976bb5e935
firmware: migrate analyzer_proto to new libio.
2018-05-14 12:51:59 +00:00
whitequark
2999756493
firmware: impl std_artiq::io::{Read,Write} for io::{Read,Write}.
2018-05-14 12:51:59 +00:00
whitequark
bfc8fd0807
firmware: add io::Error::Unrecognized variant and use it in drtioaux.
2018-05-14 12:51:59 +00:00
whitequark
7e299563df
firmware: mark many functions in libio as #[inline].
2018-05-14 11:22:56 +00:00
whitequark
368d6f9bfb
satman: remove useless _Unwind_Resume.
2018-05-14 11:22:56 +00:00
whitequark
42420e094a
satman: don't unwrap so much in process_aux_packet.
...
This shrinks the code by almost 4K.
2018-05-14 11:22:56 +00:00
whitequark
56a29b91fc
firmware: implement ConsoleLogger, use it in satman.
2018-05-14 10:45:11 +00:00
whitequark
5d43d457d2
satman: eliminate heap.
2018-05-14 10:05:02 +00:00
whitequark
46c8afc56c
firmware: implement libio and use in in drtioaux.
2018-05-14 10:02:39 +00:00
whitequark
d543c9aa63
firmware: backtrace_artiq → unwind_backtrace.
...
This crate isn't ARTIQ-specific.
2018-05-14 07:33:00 +00:00
whitequark
f383a470fe
satman: do not debug print unexpected aux packets.
...
This shrinks firmware by 2.8K.
2018-05-13 13:43:39 +00:00
whitequark
aa42a69849
libdrtioaux: always inline read/write helpers.
...
This shrinks Packet::{read_from,write_to} by 1K.
2018-05-13 13:39:14 +00:00
whitequark
32522be413
satman: use 1K log buffer and 4K stack.
...
This reduces memory requirements in half.
2018-05-13 13:28:00 +00:00
Florent Kermarrec
6b4bbe31f7
firmware/ad9154: use fixed hmc7043 sysref phase (found with scan)
2018-05-12 00:12:59 +02:00
Florent Kermarrec
3c49eba0a0
firmware/hmc830_7043: put hmc7043 in sleep mode before hmc830 initialization
...
hmc7043 seems to generate broadband noise when not initialized. This allows isolating issues. If hmc830 still does not always lock correctly, then this is not related to hmc7043 broadband noise.
2018-05-12 00:06:49 +02:00
