whitequark
93af5d2a03
compiler: handle async RPC as last statement in try block.
...
Fixes #1107 .
2018-08-07 07:06:53 +00:00
whitequark
7bd7b6592a
rpc_proto: serialize keywords correctly.
...
Fixes #1109 .
2018-08-07 06:47:09 +00:00
whitequark
259f1576c3
Fix tests after a74958f0
.
2018-08-07 06:06:49 +00:00
whitequark
a74958f01f
ksupport: raise RuntimeError on reraise with no inflight exception.
...
Fixes #1123 .
2018-08-07 05:53:13 +00:00
2008d02f4d
runtime: use different default IP and MAC for different kinds of boards
...
This helps reduce conflicts when having many boards on a development network.
2018-08-07 10:30:50 +08:00
bbe36b94f7
ad9154: enable sync in init
2018-08-06 19:02:27 +08:00
7f0b2ff594
jesd204sync: work around HMC7043 poor behavior with combined delays
...
The HMC7043 outputs poorly controlled signals when adjusting
two delays at once. This commit puts the DAC in one-shot SYSREF mode,
and only triggers synchronizations when SYSREF is stable.
2018-08-06 17:43:17 +08:00
f32f0126e2
Revert "ad9154: use continuous sync mode"
...
The HMC7043 is not really glitchless.
This reverts commit bd968211de
.
2018-08-06 16:59:53 +08:00
65f198bdee
kasli: use tester EEMs for DRTIO, add Urukul-Sayma sync example
2018-08-06 16:53:13 +08:00
bd968211de
ad9154: use continuous sync mode
2018-08-06 00:27:10 +08:00
b023865b42
sayma: instantiate dummy IBUFDS_GTE3 on unused but driven Si5324 clock pins
...
Solve same problem as e83ee3a0
but channels cannot be independently disabled.
2018-08-05 23:02:41 +08:00
e83ee3a07a
hmc7043: disable GTP_CLK1 when not in use
...
Termination and biasing are not active at the FPGA when IBUFDS_GTE3 is
not instantiated, and driving a clock then leads to overvoltage.
2018-08-03 10:03:52 +08:00
6fc8439399
tweak moninj to allow old dashboard with new firmware
2018-08-02 19:34:14 +08:00
04cbc3237b
test_moninj: test injection monitoring
2018-08-02 19:34:14 +08:00
47740c8930
share moninj injection state between dashboards
...
Previously if one dashboard overrode a channel this was not visible on
any other dashboard - the channel appeared to operate normally.
2018-08-02 19:34:14 +08:00
7d6a1b528d
ad9912: add ftw_to_frequency
2018-08-02 11:19:12 +00:00
e518a1f1d0
ad53xx: also increase slack after control readback
2018-08-02 11:19:12 +00:00
whitequark
5871d13da8
firmware: actually compact in config::compact().
...
Fixes #1116 .
2018-08-01 16:27:48 +00:00
David Nadlinger
829fca6112
pyon: Correctly deserialize bare NaNs
...
This also fixes (non-numpy) lists containing NaNs.
Previously, accidentally storing a NaN in a dataset would
bring down large parts of the system.
2018-07-30 11:08:56 +01:00
David Nadlinger
08ee91beb2
ad9910: Clarify chip_select range [nfc]
...
`assert 3 <= chip_select <= 7` is rather opaque without looking
at the CPLD source code otherwise.
2018-07-30 11:08:17 +01:00
David Nadlinger
6b89106578
ad53xx: Avoid sporadic RTIOUnderflow in init()
...
I observed sporadic RTIO underflows on Kasli before, by ~2.5 µs,
so 5 µs extra slack should be plenty. No underflows since.
2018-07-28 23:45:48 +01:00
c00eb181fc
conda: bump jesd204b
2018-07-28 13:17:44 +08:00
e4d48a78eb
drtio: wait for remote to ack TSC synchronization
...
Sayma takes a long time after TSC sync to align SYSREF, and this caused two issues:
1. Aux packets getting lost and causing error reports
2. DRTIO links reported up and kernels proceeding despite the DACs not being properly synced.
2018-07-26 20:28:17 +08:00
83de8b2ba2
drtio: add ping timeout during link init
2018-07-26 20:27:53 +08:00
446f791180
firmware: simplify SYSREF DRTIO alignment
2018-07-26 19:37:59 +08:00
f8c17528e7
satman: use new SYSREF code
2018-07-26 16:26:57 +08:00
32c95ac034
sayma: automated DAC SYSREF phase calibration
2018-07-26 16:23:55 +08:00
dbcf2fe9b4
firmware: remove 'chip found' messages on Sayma
2018-07-26 16:07:37 +08:00
d523d03f71
sayma: automated FPGA SYSREF phase offset calibration
2018-07-26 14:53:28 +08:00
0a9d3638ee
config: add write_int
2018-07-26 14:49:32 +08:00
19c51c644e
grabber: cleanup GRABBER_STATE
2018-07-24 19:08:51 +08:00
fb96c1140e
grabber: add coredevice driver
2018-07-24 18:06:44 +08:00
b38c685857
grabber: fix pix.stb
2018-07-24 11:32:32 +08:00
60a7e0e40d
grabber: use usual order of ROI coordinates in cfg addresses
2018-07-24 10:55:13 +08:00
015c592ab7
conda: bump jesd204b
2018-07-21 15:49:40 +08:00
7b75026391
grabber: add MultiReg to transfer ROI boundaries
2018-07-21 13:40:12 +08:00
4a4d0f8e51
grabber: fix missing variable rename
2018-07-21 13:39:46 +08:00
3638a966e1
kasli: add false path between RTIO and CL clocks
2018-07-21 13:26:13 +08:00
031de58d21
grabber: complete RTIO PHY, untested
2018-07-21 13:25:47 +08:00
e3ba4b9516
grabber: minor ROI engine cleanup, export count_len, cap count width to 31
2018-07-21 13:25:13 +08:00
766d87f626
doc: artiq_coreconfig → artiq_coremgmt config. Closes #1111
2018-07-20 11:59:07 +08:00
cab0ba408d
fmcdio_vhdci_eem: cleanup and document
2018-07-20 09:57:03 +08:00
d152506ecb
sayma: update fmcdio_vhdci_eem demo
2018-07-19 15:47:20 +08:00
8dfcd463aa
fmcdio_vhdci_eem: naming consistency
2018-07-19 15:46:04 +08:00
fe93a454d6
fmcdio_vhdci_eem: fix direction shift register permutation and polarity
2018-07-19 15:16:21 +08:00
e71cbe53a6
firmware: cleanup Cargo.lock
2018-07-18 10:37:43 +08:00
31f4f8792a
sayma: add Urukul and Zotino to example device_db
2018-07-18 10:31:55 +08:00
25170a53e5
sayma: add back Urukul and Zotino
2018-07-18 10:27:54 +08:00
5e62910a8d
examples: add Sayma VHDCI DIO
2018-07-17 23:28:05 +08:00
8b9a8be12a
fmcdio_vhdci_eem: add dirctl word computation functions
2018-07-17 23:27:29 +08:00