linuswck

linuswck pushed to master at M-Labs/kirdy

2024-02-15 12:49:29 +08:00

d2efc02b6a eth_cmd_test: Reset ld current to 0A during SIGINT

linuswck pushed to master at M-Labs/kirdy

2024-02-15 12:15:15 +08:00

89d415194d update eth_cmd_test code

09b3765877 pid_autotune: Add pid autotune script

7a76325288 cmd: rm rev from cmd json

ffa5f4e8ff pid: Use Thermostat's PID algo instead of IDSP

e9a396f001 thermostat: Add abs timestamp to StatusReport

Compare 9 commits »

linuswck commented on issue sinara-hw/kirdy#32

2024-02-07 16:06:34 +08:00

MCU's Firmware Starts before Analog Power Rails are "Power Good"

After Digital 3V3 Power Rail is stabilized, Analog 3V3A Power Rail takes around 1.12s to reach 90% of its output voltage(LT3042's PG Definition) and takes around 1.5s to reaches >95% of its…

linuswck pushed to master at M-Labs/kirdy

2024-02-07 12:46:27 +08:00

6b05b2d851 Fix Power Up Hw Issue

linuswck pushed to master at M-Labs/kirdy

2024-02-07 11:57:56 +08:00

f22ab430b8 pid: Use IDSP impl of Pid, Add Eth Pid Ctrl Cmds

4cd650367d thermostat: cleanup pid_engaged fn

de262b849d eth: Add Thermostat related json cmd

Compare 3 commits »

linuswck pushed to master at sinara-hw/kirdy

2024-02-06 17:12:29 +08:00

4c69a080b1 bom: update MFR_PN and descriptions of SMA Cable

linuswck commented on issue sinara-hw/kirdy#32

2024-02-06 15:40:55 +08:00

MCU's Firmware Starts before Analog Power Rails are "Power Good"

Yes. Should be a simple bug fix in code depending hw revision.

linuswck opened issue sinara-hw/kirdy#32

2024-02-06 14:49:42 +08:00

MCU's Firmware starts before Analog Power Rails are "Power Good"

linuswck pushed to master at sinara-hw/kirdy

2024-02-05 14:43:24 +08:00

c08d3d36b4 Panel: Add Mounting Plates for Fiber Optic Adapters

c7cfa18a99 sch: Add M3 Washer to BOM

Compare 2 commits »

linuswck pushed to master at M-Labs/kirdy

2024-02-02 17:38:45 +08:00

4132bfacd3 boot: Set thermostat & LD init output current to 0

linuswck pushed to master at M-Labs/kirdy

2024-02-02 17:36:57 +08:00

4f44925bb7 boot: Turn off thermostat and LD by default

6096711d2c eth: Poll and Handle Json based Ld ctrl cmd

3d3d6f5cb5 ld: cleanup

Compare 3 commits »

linuswck pushed to master at M-Labs/kirdy

2024-02-01 16:25:06 +08:00

172c3e1dfc cleanup boot.rs, thermostat.rs

ee0ed8ebe7 eth: add drivers for init, polling & sending data

771f2813f7 gpio: correct wrong eth pin definition

4e0d14def2 laser: Add driver and fn to get termination status

Compare 4 commits »

linuswck opened issue sinara-hw/kirdy#31

2024-01-29 16:24:36 +08:00

Fiber optic adapter mounted on front panel may block the access of alternate programming pin header

linuswck pushed to master at M-Labs/kirdy

2024-01-26 16:57:24 +08:00

f6677d874c LD: Rst LD current at power_up for soft start

d391e3a1fb LD: Setting LD output current now ramps up slowly

edd30e94a0 laser_diode: Add fn to set pd_dark_i

ad731c2f15 rename pd_mon -> pd_responsitivity

9d8a553669 pd_mon: add fns to convert between pwr and current

Compare 10 commits »

linuswck pushed to master at M-Labs/kirdy

2024-01-24 12:29:01 +08:00

07ea733b34 thermostst: Patch hw related settings for rev0_3

linuswck pushed to master at M-Labs/kirdy

2024-01-24 12:20:23 +08:00

5bea3f0e5f boot: init analog wdg & power up laser after cfg

af283b17ac laser_diode: use analog wdg fns

c3022e9db1 Analog_Wdg: Add GPIO init

c02181c80c laser diode: Add Analog Watchdog initial commit

095fe8ea69 AD7172: Rm deprecated warning for Rev0_2 hw bug

Compare 21 commits »

linuswck commented on issue sinara-hw/kirdy#29

2024-01-24 11:27:09 +08:00

components bump into card guides

I will correct it in a future commit along with a Rule Area added for the edge rail.

linuswck commented on issue sinara-hw/kirdy#30

2024-01-24 11:04:52 +08:00

[Rev0_3] Front Panel is connected to PCB Ground

It is indeed not an issue and does not affect the low noise signal path.

linuswck pushed to master at sinara-hw/kirdy

2024-01-24 10:56:55 +08:00

43c5afefab sch: correct MFR/PNs for BSS138, TLV9001, TPS54620

linuswck closed issue sinara-hw/kirdy#30

2024-01-24 10:55:34 +08:00

[Rev0_3] Front Panel is connected to PCB Ground