cdf900a5b6
gpio: Add AD7172 phy gpio init
...
- Will not function on rev0_2 kirdy due to wrong hardware connection
2024-01-16 17:36:16 +08:00
af8d361b95
AD7172: Add AD7172 drivers fns
...
- Port from Thermostat Firmware
2024-01-16 16:19:01 +08:00
e355e83d28
memory.x: Add comment on the reserved flash sector
2024-01-16 15:27:43 +08:00
285fc9b5d6
memory.x: Reserved Flash Sector 11 for Config
2024-01-15 17:44:44 +08:00
8c612fc0c9
memory.x: RM CONFIG MEMORY area in linker script
...
- STM32f407 does not have second bank or flash/ Sector 12 unlike F427
2024-01-15 17:43:17 +08:00
42cd55645c
main: Add demo fns to use on-board flash
2024-01-15 17:21:48 +08:00
d190b8b192
flash: Add init boot seq
...
- Max flash erase time for PSize = 8 and 128KiB Sector is 4s
- Watchdog period is changed accordingly
2024-01-15 17:21:06 +08:00
74325a3cee
flash: Add fns to store data in flash
...
- Writing to the wrong flash sector can cause MCU to stall
- Only 16KiB out of 128KiB in the sector is used to save RAM for compacting
2024-01-15 17:14:58 +08:00
709eae8566
max5719: Slow down SPI clock
...
- setting it to 30MHz hang MCU core
2024-01-11 17:46:35 +08:00
d3e3451d37
Add README.md for flashing instructions
2024-01-11 17:17:38 +08:00
33ff0c3678
main: Add demo fns reading all hardware status
2024-01-11 17:17:38 +08:00
33d9cb45c4
ld_drive: Add soft current limit
2024-01-11 17:17:38 +08:00
8ae27725c6
Port PID Controller from thermostat firmware
...
- Add serde Cargo
2024-01-11 17:17:10 +08:00
20fc6d6fac
rm photodiode folder and its mod.rs
...
- photodiode related fns are written inside laser diode folder
- as they are closely related
2024-01-10 17:51:27 +08:00
654964831a
boot: Change thermostat boot seq for new setup seq
...
- Power Up -> Calibrate -> Set the TEC current to some value
2024-01-10 10:38:05 +08:00
27c7b5929e
thermostat: change setup seq
...
- default power off
- with all params set to default val on hw
- rm calibration from setup
2024-01-10 10:38:05 +08:00
e48f1979f0
Clean up warnings
2024-01-10 10:38:05 +08:00
59f2385ecf
ld_drive: make settings private & add set & get fn
2024-01-10 10:38:05 +08:00
d4e074cbd4
ld_drive: rebase to the point that declare set_i
2024-01-10 10:38:05 +08:00
277796d2a4
boot: Add ld_drive boot sequence
2024-01-10 10:38:05 +08:00
be8bf0a8b6
ld_drive: add setup fn
2024-01-10 10:38:05 +08:00
b1123047c7
ld_drive: Add fns to get pd current & cal ld pwr
2024-01-10 10:38:05 +08:00
707fac0775
ld_drive: add a param for setting to cal pd pwr
...
- Conversion ratio between pd current and ld output power
2024-01-10 10:38:05 +08:00
a99dde8b38
current_source: add driver to read pd voltage
2024-01-10 10:38:05 +08:00
d1f7a20c15
ld_drive: Add fns to set ld output current
2024-01-10 10:38:05 +08:00
58a8b15c40
ld_drive: add unit type and hw related constant
2024-01-10 10:38:05 +08:00
590ba8171c
Add high level ld_drive mod
...
- Use current_source driver to interface with the board
2024-01-10 10:38:05 +08:00
0807f66b3c
Add digital gpio related fns to Current source
...
- power_up
- power_down
- ld_short_enable
- ld_short_disable
- Rev0_2 has hardware connection bug for LD_EN net.
- laser driver power will always be enabled
2024-01-10 10:38:05 +08:00
2953d4edde
Rewrite current_source obj and add gpio init
2024-01-10 10:38:05 +08:00
f2c026ffdd
Rewrite MAX5719 Driver into a separated file
2024-01-10 10:38:05 +08:00
c7d36bc8d5
Reorganize variables and fns structure
2024-01-10 10:38:00 +08:00
784fc03957
cargo: add miniconf
2024-01-10 10:36:13 +08:00
6cc2bc32c5
thermostat:reorganize fns structure, add setup seq
2024-01-10 10:36:09 +08:00
23ee568ea7
Port TEC DAC calibration procedure from Thermostat
...
- Needs clean up
- To be evaluated and rethink the calibration procedure
2024-01-10 10:36:05 +08:00
d3f3608136
DacVFb is changed to PC3 for rev0_2 prototype
...
- This requires a circuit change to connect it to the PoE_PWR_SRC
through a 1.6k Ohm and 100nF LPF
2023-12-21 16:39:09 +08:00
4cf7b7fdf9
Rewrite MAX1968 Driver Generically
...
- Set variable to proper types(Rate, ElectricalPotential, etc)
- Declare const MAX_I_POS, MAX_I_NEG, MAX_V conversion
2023-12-21 13:13:06 +08:00
0179e7641a
Add MAX1968 Startup Sequence
2023-12-20 14:51:34 +08:00
f6767b147b
Fix typo in MAX1968 driver power_down fn
2023-12-20 14:48:47 +08:00
475fe28604
Initial Commit for AD5680 and MAX1968 Drivers
...
- GPIO Initializations for AD5680, MAX1968 drivers
- CTLI voltage of MAX1968 can be set with AD5680
- All features of MAX1968 can be controlled
2023-12-20 12:08:48 +08:00
764a203dd8
Update stm32-eth cargo crate to 0.15.2
...
- stm32-eth crate requires stm32f4xx-hal 0.14.0 and smoltcp 0.10.0
- its dependency packages requires rustc 1.67 or above (1.67.1 is chosen)
2023-12-15 16:40:55 +08:00
f2b419f8d0
Fix nix build to compilation error at Check Phase
...
- "panic_handler" should not be declared during test
- "main" and "std" are needed during test
2023-12-15 13:21:19 +08:00
topquark12
1b3b121a2d
cleanup
2022-10-23 16:59:15 +08:00
topquark12
e562b822dc
use RTT for PanicInfo
2022-10-22 21:00:17 +08:00
topquark12
6a76536248
squash all warnings, add RTT support
2022-10-22 20:20:49 +08:00
topquark12
6867a293e5
squash (most) warnings, cleanup
2022-10-22 15:49:01 +08:00
topquark12
dbb1b03638
current source working
2022-10-22 01:58:18 +08:00
topquark12
361c2ff316
add gpio setup
2022-10-21 12:05:55 +08:00
topquark12
18a603ab5f
refactor, shorten main
2022-10-20 21:21:01 +08:00
topquark12
fc90593f84
blinky, working systick and delay
2022-10-20 20:57:24 +08:00
topquark12
710b3ff5d5
project init
2022-10-20 15:17:43 +08:00
