working
This commit is contained in:
parent
155aa5c032
commit
44c36b203d
10
memory.x
10
memory.x
|
|
@ -1,5 +1,11 @@
|
|||
MEMORY
|
||||
{
|
||||
FLASH : ORIGIN = 0x08000000, LENGTH = 512K
|
||||
RAM : ORIGIN = 0x20000000, LENGTH = 112K /* of 112K + 16K */
|
||||
ITCM : ORIGIN = 0x00000000, LENGTH = 64K
|
||||
RAM : ORIGIN = 0x20000000, LENGTH = 128K
|
||||
RAM_D1 : ORIGIN = 0x24000000, LENGTH = 512K
|
||||
RAM_D2 : ORIGIN = 0x30000000, LENGTH = 288K
|
||||
RAM_D3 : ORIGIN = 0x38000000, LENGTH = 64K
|
||||
RAM_B : ORIGIN = 0x38800000, LENGTH = 4K
|
||||
FLASH : ORIGIN = 0x08000000, LENGTH = 1024K
|
||||
FLASH1 : ORIGIN = 0x08100000, LENGTH = 1024K
|
||||
}
|
||||
|
|
|
|||
|
|
@ -1,10 +1,6 @@
|
|||
source [find interface/stlink.cfg]
|
||||
transport select hla_swd
|
||||
source [find target/stm32h7x_dual_bank.cfg]
|
||||
|
||||
source [find stm32h7x.cfg]
|
||||
# STM32H7xxxI 2Mo have a dual bank flash.
|
||||
# Add the second flash bank.
|
||||
set _FLASHNAME $_CHIPNAME.flash1
|
||||
flash bank $_FLASHNAME stm32h7x 0x08100000 0 0 0 $_TARGETNAME
|
||||
|
||||
reset_config srst_only
|
||||
# reset_config srst_only
|
||||
reset_config none
|
||||
|
|
|
|||
112
stm32h7.cfg
112
stm32h7.cfg
|
|
@ -1,112 +0,0 @@
|
|||
# script for stm32h7x family
|
||||
|
||||
#
|
||||
# stm32h7 devices support both JTAG and SWD transports.
|
||||
#
|
||||
source [find target/swj-dp.tcl]
|
||||
source [find mem_helper.tcl]
|
||||
|
||||
if { [info exists CHIPNAME] } {
|
||||
set _CHIPNAME $CHIPNAME
|
||||
} else {
|
||||
set _CHIPNAME stm32h7x
|
||||
}
|
||||
|
||||
set _ENDIAN little
|
||||
|
||||
# Work-area is a space in RAM used for flash programming
|
||||
# By default use 64kB
|
||||
if { [info exists WORKAREASIZE] } {
|
||||
set _WORKAREASIZE $WORKAREASIZE
|
||||
} else {
|
||||
set _WORKAREASIZE 0x10000
|
||||
}
|
||||
|
||||
#jtag scan chain
|
||||
if { [info exists CPUTAPID] } {
|
||||
set _CPUTAPID $CPUTAPID
|
||||
} else {
|
||||
if { [using_jtag] } {
|
||||
set _CPUTAPID 0x6ba00477
|
||||
} {
|
||||
set _CPUTAPID 0x6ba02477
|
||||
}
|
||||
}
|
||||
|
||||
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
||||
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
||||
|
||||
if {[using_jtag]} {
|
||||
swj_newdap $_CHIPNAME bs -irlen 5
|
||||
}
|
||||
|
||||
set _TARGETNAME $_CHIPNAME.cpu
|
||||
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
|
||||
|
||||
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
||||
|
||||
set _FLASHNAME $_CHIPNAME.flash
|
||||
flash bank $_FLASHNAME stm32h7x 0x08000000 0 0 0 $_TARGETNAME
|
||||
|
||||
# Clock after reset is HSI at 64 MHz, no need of PLL
|
||||
adapter_khz 1800
|
||||
|
||||
adapter_nsrst_delay 100
|
||||
if {[using_jtag]} {
|
||||
jtag_ntrst_delay 100
|
||||
}
|
||||
|
||||
# use hardware reset
|
||||
#
|
||||
# The STM32H7 does not support connect_assert_srst mode because the AXI is
|
||||
# unavailable while SRST is asserted, and that is used to access the DBGMCU
|
||||
# component at 0x5C001000 in the examine-end event handler.
|
||||
#
|
||||
# It is possible to access the DBGMCU component at 0xE00E1000 via AP2 instead
|
||||
# of the default AP0, and that works with SRST asserted; however, nonzero AP
|
||||
# usage does not work with HLA, so is not done by default. That change could be
|
||||
# made in a local configuration file if connect_assert_srst mode is needed for
|
||||
# a specific application and a non-HLA adapter is in use.
|
||||
reset_config srst_only srst_nogate
|
||||
|
||||
if {![using_hla]} {
|
||||
# if srst is not fitted use SYSRESETREQ to
|
||||
# perform a soft reset
|
||||
cortex_m reset_config sysresetreq
|
||||
|
||||
# Set CSW[27], which according to ARM ADI v5 appendix E1.4 maps to AHB signal
|
||||
# HPROT[3], which according to AMBA AHB/ASB/APB specification chapter 3.7.3
|
||||
# makes the data access cacheable. This allows reading and writing data in the
|
||||
# CPU cache from the debugger, which is far more useful than going straight to
|
||||
# RAM when operating on typical variables, and is generally no worse when
|
||||
# operating on special memory locations.
|
||||
$_CHIPNAME.dap apcsw 0x08000000 0x08000000
|
||||
}
|
||||
|
||||
$_TARGETNAME configure -event examine-end {
|
||||
# Enable D3 and D1 DBG clocks
|
||||
# DBGMCU_CR |= D3DBGCKEN | D1DBGCKEN
|
||||
mmw 0x5C001004 0x00600000 0
|
||||
|
||||
# Enable debug during low power modes (uses more power)
|
||||
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP in D3 & D1 Domains
|
||||
mmw 0x5C001004 0x00000187 0
|
||||
|
||||
# Stop watchdog counters during halt
|
||||
# DBGMCU_APB3FZ1 |= WWDG1
|
||||
mmw 0x5C001034 0x00000040 0
|
||||
# DBGMCU_APB4FZ1 |= WDGLSD1
|
||||
mmw 0x5C001054 0x00040000 0
|
||||
}
|
||||
|
||||
$_TARGETNAME configure -event trace-config {
|
||||
# Set TRACECLKEN; TRACE_MODE is set to async; when using sync
|
||||
# change this value accordingly to configure trace pins
|
||||
# assignment
|
||||
mmw 0x5C001004 0x00100000 0
|
||||
}
|
||||
|
||||
$_TARGETNAME configure -event reset-init {
|
||||
# Clock after reset is HSI at 64 MHz, no need of PLL
|
||||
adapter_khz 4000
|
||||
}
|
||||
Loading…
Reference in New Issue