linuswck
/
kirdy-firmware
forked from M-Labs/kirdy
1
0
Fork 0
Code Pull Requests Activity
125 Commits 5 Branches 0 Tags 2.1 MiB
Commit Graph

30 Commits

Author SHA1 Message Date
linuswck f488786e1c Use DMA to read Tec_I & Tec_V 
- Remove the single conversion polling time with DMA
 2024-03-01 11:31:01 +08:00
linuswck d1cc677668 thermostat: split poll_adc & update_pid into 2 fns 2024-02-28 12:21:37 +08:00
linuswck c09ccc29cd cmd: Add cmd to get all device settings 2024-02-23 12:45:29 +08:00
linuswck a8787430b1 Add Temperature Monitor to Thermostat 
- Issue an alarm when temperature goes out of user-defined operating range during Pid Controller startup
    or reading is outside of +-0.5 Degree from temperature set point after Pid Controller becomes stable
- If alarm is observed, power down laser and tec controller and disengage Pid Controller
- Add the corresponding cmd for configuring the temperature monitor
 2024-02-21 17:32:11 +08:00
linuswck 88cca12a60 ld: Use Timer IRQ to ramp up/down output current 
- Fixes possible watchdog timeout
- Improves ethernet response time & thermostat Pid update interval consistency
 2024-02-20 16:18:06 +08:00
linuswck 5f83b73011 cmd: Add active report mode cmd 2024-02-19 15:08:00 +08:00
linuswck 0642640da7 dfu: Add eth cmd, fns to put stm32 into dfu mode 2024-02-16 17:23:47 +08:00
linuswck e29898f8f8 fix typos 2024-02-15 12:14:14 +08:00
linuswck f22ab430b8 pid: Use IDSP impl of Pid, Add Eth Pid Ctrl Cmds 2024-02-07 11:56:38 +08:00
linuswck de262b849d eth: Add Thermostat related json cmd 2024-02-05 15:14:23 +08:00
linuswck 6096711d2c eth: Poll and Handle Json based Ld ctrl cmd 
- Upgrade to miniconf 9.0
- Only non report related laser diode ctrl command is implemented
 2024-02-02 17:35:58 +08:00
linuswck ee0ed8ebe7 eth: add drivers for init, polling & sending data 2024-02-01 16:20:36 +08:00
linuswck 4e0d14def2 laser: Add driver and fn to get termination status 2024-01-30 13:01:33 +08:00
linuswck 85b50bf824 Analog_Wdg: Finish Power Excursion Protection fns 
- Verified to be working
 2024-01-26 16:56:39 +08:00
linuswck af283b17ac laser_diode: use analog wdg fns 2024-01-24 12:18:42 +08:00
linuswck 2f7ca2a706 Thermostat: Add fns to report status & settings 
- Report all system status, PID Settings, NTC parameter, TEC Settings
 2024-01-24 12:16:06 +08:00
linuswck 42cd55645c main: Add demo fns to use on-board flash 2024-01-15 17:21:48 +08:00
linuswck d190b8b192 flash: Add init boot seq 
- Max flash erase time for PSize = 8 and 128KiB Sector is 4s
- Watchdog period is changed accordingly
 2024-01-15 17:21:06 +08:00
linuswck 33ff0c3678 main: Add demo fns reading all hardware status 2024-01-11 17:17:38 +08:00
linuswck 277796d2a4 boot: Add ld_drive boot sequence 2024-01-10 10:38:05 +08:00
linuswck 4cf7b7fdf9 Rewrite MAX1968 Driver Generically 
- Set variable to proper types(Rate, ElectricalPotential, etc)
- Declare const MAX_I_POS, MAX_I_NEG, MAX_V conversion
 2023-12-21 13:13:06 +08:00
linuswck 475fe28604 Initial Commit for AD5680 and MAX1968 Drivers 
- GPIO Initializations for AD5680, MAX1968 drivers
- CTLI voltage of  MAX1968 can be set with AD5680
- All features of MAX1968 can be controlled
 2023-12-20 12:08:48 +08:00
linuswck f2b419f8d0 Fix nix build to compilation error at Check Phase 
- "panic_handler" should not be declared during test
- "main" and "std" are needed during test
 2023-12-15 13:21:19 +08:00
topquark12 1b3b121a2d cleanup 2022-10-23 16:59:15 +08:00
topquark12 e562b822dc use RTT for PanicInfo 2022-10-22 21:00:17 +08:00
topquark12 6867a293e5 squash (most) warnings, cleanup 2022-10-22 15:49:01 +08:00
topquark12 361c2ff316 add gpio setup 2022-10-21 12:05:55 +08:00
topquark12 18a603ab5f refactor, shorten main 2022-10-20 21:21:01 +08:00
topquark12 fc90593f84 blinky, working systick and delay 2022-10-20 20:57:24 +08:00
topquark12 710b3ff5d5 project init 2022-10-20 15:17:43 +08:00