Merge pull request 'sdio-registers' (#29)
This commit is contained in:
commit
2c82fb793e
@ -17,4 +17,5 @@ pub mod flash;
|
||||
pub mod dmac;
|
||||
pub mod time;
|
||||
pub mod timer;
|
||||
pub mod sdio;
|
||||
pub mod logger;
|
||||
|
||||
1
libboard_zynq/src/sdio/mod.rs
Normal file
1
libboard_zynq/src/sdio/mod.rs
Normal file
@ -0,0 +1 @@
|
||||
mod regs;
|
||||
547
libboard_zynq/src/sdio/regs.rs
Normal file
547
libboard_zynq/src/sdio/regs.rs
Normal file
@ -0,0 +1,547 @@
|
||||
use volatile_register::{RO, RW, WO};
|
||||
|
||||
use libregister::{register, register_at, register_bit, register_bits, register_bits_typed};
|
||||
|
||||
#[repr(C)]
|
||||
pub struct RegisterBlock {
|
||||
pub sdma_system_address: RW<u32>,
|
||||
pub block_size_block_count: BlockSizeBlockCount,
|
||||
pub argument: RW<u32>,
|
||||
pub transfer_mode_command: TransferModeCommand,
|
||||
pub responses: [RO<u32>; 4],
|
||||
pub buffer: RW<u32>,
|
||||
pub present_state: PresentState,
|
||||
/// Host. power, block gap, wakeup control
|
||||
pub control: Control,
|
||||
/// Clock and timeout control, and software reset register.
|
||||
pub timing_control: TimingControl,
|
||||
pub interrupt_status: InterruptStatus,
|
||||
pub interrupt_status_en: InterruptStatusEn,
|
||||
pub interrupt_signal_en: InterruptSignalEn,
|
||||
pub auto_cmd12_error_status: AutoCmd12ErrorStatus,
|
||||
pub capabilities: Capabilities,
|
||||
pub max_current_capabilities: MaxCurrentCapabilities,
|
||||
pub force_event: ForceEvent,
|
||||
pub adma_error_status: AdmaErrorStatus,
|
||||
pub adma_system_address: RW<u32>,
|
||||
pub boot_data_timeout_counter: RW<u32>,
|
||||
pub debug_selection: DebugSelection,
|
||||
pub spi_interrupt_support: SpiInterruptSupport,
|
||||
pub misc_reg: MiscReg,
|
||||
}
|
||||
|
||||
#[allow(unused)]
|
||||
#[repr(u8)]
|
||||
pub enum CommandType {
|
||||
Normal = 0b00,
|
||||
Suspend = 0b01,
|
||||
Resume = 0b10,
|
||||
Abort = 0b11,
|
||||
}
|
||||
|
||||
#[allow(unused)]
|
||||
#[repr(u8)]
|
||||
pub enum ResponseTypeSelect {
|
||||
NoResponse = 0b00,
|
||||
Length136 = 0b01,
|
||||
Length48 = 0b10,
|
||||
Legnth48Check = 0b11,
|
||||
}
|
||||
|
||||
#[allow(unused)]
|
||||
#[repr(u8)]
|
||||
pub enum BusVoltage {
|
||||
/// 3.3V
|
||||
V33 = 0b111,
|
||||
/// 3.0V, typ.
|
||||
V30 = 0b110,
|
||||
/// 1.8V, typ.
|
||||
V18 = 0b101,
|
||||
}
|
||||
|
||||
#[allow(unused)]
|
||||
#[repr(u8)]
|
||||
pub enum DmaSelect {
|
||||
SDMA = 0b00,
|
||||
ADMA1 = 0b01,
|
||||
ADMA2 = 0b10,
|
||||
ADMA3 = 0b11,
|
||||
}
|
||||
|
||||
#[allow(unused)]
|
||||
#[repr(u8)]
|
||||
/// SDCLK Frequency divisor, d(number) means baseclock divided by (number).
|
||||
pub enum SdclkFreqDivisor {
|
||||
D256 = 0x80,
|
||||
D128 = 0x40,
|
||||
D64 = 0x20,
|
||||
D32 = 0x10,
|
||||
D16 = 0x08,
|
||||
D8 = 0x04,
|
||||
D4 = 0x02,
|
||||
D2 = 0x01,
|
||||
D1 = 0x00,
|
||||
}
|
||||
|
||||
#[allow(unused)]
|
||||
#[repr(u8)]
|
||||
pub enum AdmaErrorState {
|
||||
StStop = 0b00,
|
||||
StFds = 0b01,
|
||||
StTfr = 0b11,
|
||||
}
|
||||
|
||||
#[allow(unused)]
|
||||
#[repr(u8)]
|
||||
pub enum SpecificationVersion {
|
||||
V1 = 0,
|
||||
V2 = 1,
|
||||
}
|
||||
|
||||
register_at!(RegisterBlock, 0xE0100000, sd0);
|
||||
register_at!(RegisterBlock, 0xE0101000, sd1);
|
||||
|
||||
register!(block_size_block_count, BlockSizeBlockCount, RW, u32);
|
||||
register_bits!(
|
||||
block_size_block_count,
|
||||
/// Current transfer block count.
|
||||
blocks_count,
|
||||
u16,
|
||||
16,
|
||||
31
|
||||
);
|
||||
register_bits!(
|
||||
block_size_block_count,
|
||||
/// Host SDMA Buffer Size, size = 2^(val + 2) KB.
|
||||
dma_buffer_size,
|
||||
u8,
|
||||
12,
|
||||
14
|
||||
);
|
||||
register_bits!(
|
||||
block_size_block_count,
|
||||
/// Block size for data transfer. Unit: byte.
|
||||
transfer_block_size,
|
||||
u16,
|
||||
0,
|
||||
11
|
||||
);
|
||||
|
||||
register!(transfer_mode_command, TransferModeCommand, RW, u32);
|
||||
register_bits!(
|
||||
transfer_mode_command,
|
||||
/// Command Number.
|
||||
command_index,
|
||||
u8,
|
||||
24,
|
||||
29
|
||||
);
|
||||
register_bits_typed!(
|
||||
transfer_mode_command,
|
||||
/// Command type register.
|
||||
command_type,
|
||||
u8,
|
||||
CommandType,
|
||||
22,
|
||||
23
|
||||
);
|
||||
register_bit!(
|
||||
transfer_mode_command,
|
||||
/// 1 if data is present and shall be transferred using the DAT line.
|
||||
data_present_select,
|
||||
21
|
||||
);
|
||||
register_bit!(
|
||||
transfer_mode_command,
|
||||
/// If the index field shall be checked.
|
||||
index_check_en,
|
||||
20
|
||||
);
|
||||
register_bit!(
|
||||
transfer_mode_command,
|
||||
/// If CRC shall be checked.
|
||||
crc_check_en,
|
||||
19
|
||||
);
|
||||
register_bits_typed!(
|
||||
transfer_mode_command,
|
||||
/// Different type of response.
|
||||
response_type_select,
|
||||
u8,
|
||||
ResponseTypeSelect,
|
||||
16,
|
||||
17
|
||||
);
|
||||
register_bit!(
|
||||
transfer_mode_command,
|
||||
/// Enables the multi block DAT line data transfer.
|
||||
multi_block_en,
|
||||
5
|
||||
);
|
||||
register_bit!(
|
||||
transfer_mode_command,
|
||||
/// 1 if read (card to host), 0 if write (host to card).
|
||||
direction_select,
|
||||
4
|
||||
);
|
||||
register_bit!(
|
||||
transfer_mode_command,
|
||||
/// If CMD12 shall be issued automatically when last block transfer is completed.
|
||||
auto_cmd12_en,
|
||||
2
|
||||
);
|
||||
register_bit!(
|
||||
transfer_mode_command,
|
||||
/// Enable the block count register.
|
||||
block_count_en,
|
||||
1
|
||||
);
|
||||
register_bit!(
|
||||
transfer_mode_command,
|
||||
/// Enable DMA,
|
||||
dma_en,
|
||||
0
|
||||
);
|
||||
|
||||
register!(present_state, PresentState, RO, u32);
|
||||
register_bit!(
|
||||
present_state,
|
||||
/// CMD Line Signal Level.
|
||||
cmd_line_level,
|
||||
24
|
||||
);
|
||||
register_bit!(
|
||||
present_state,
|
||||
/// Signal level in DAT[3]
|
||||
dat3_level,
|
||||
23
|
||||
);
|
||||
register_bit!(
|
||||
present_state,
|
||||
/// Signal level in DAT[2]
|
||||
dat2_level,
|
||||
22
|
||||
);
|
||||
register_bit!(
|
||||
present_state,
|
||||
/// Signal level in DAT[1]
|
||||
dat1_level,
|
||||
21
|
||||
);
|
||||
register_bit!(
|
||||
present_state,
|
||||
/// Signal level in DAT[0]
|
||||
dat0_level,
|
||||
20
|
||||
);
|
||||
register_bit!(
|
||||
present_state,
|
||||
/// Write enabled and inverse of SDx_WP pin level.
|
||||
write_enabled,
|
||||
19
|
||||
);
|
||||
register_bit!(
|
||||
present_state,
|
||||
/// Card detected and inverse of SDx_CDn pin level.
|
||||
card_detected,
|
||||
18
|
||||
);
|
||||
register_bit!(present_state, card_state_stable, 17);
|
||||
register_bit!(present_state, card_inserted, 16);
|
||||
register_bit!(present_state, buffer_read_en, 11);
|
||||
register_bit!(present_state, buffer_write_en, 10);
|
||||
register_bit!(present_state, read_transfer_active, 9);
|
||||
register_bit!(present_state, write_transfer_active, 8);
|
||||
register_bit!(present_state, dat_line_active, 2);
|
||||
register_bit!(present_state, command_inhibit_dat, 1);
|
||||
register_bit!(present_state, command_inhibit_cmd, 0);
|
||||
|
||||
register!(control, Control, RW, u32);
|
||||
register_bit!(
|
||||
control,
|
||||
/// Enable wakeup event via SD card removal assertion.
|
||||
wakeup_on_removal,
|
||||
26
|
||||
);
|
||||
register_bit!(
|
||||
control,
|
||||
/// Enable wakeup event via SD card insertion assertion.
|
||||
wakeup_on_insertion,
|
||||
25
|
||||
);
|
||||
register_bit!(
|
||||
control,
|
||||
/// Enable wakeup event via card interrupt assertion.
|
||||
wakeup_on_interrupt,
|
||||
24
|
||||
);
|
||||
register_bit!(
|
||||
control,
|
||||
///Enable interrupt detection at the block gap for a multiple block transfer.
|
||||
interrupt_at_block_gap,
|
||||
19
|
||||
);
|
||||
register_bit!(
|
||||
control,
|
||||
/// Enable the use of the read wait protocol.
|
||||
read_wait_control,
|
||||
18
|
||||
);
|
||||
register_bit!(
|
||||
control,
|
||||
/// Restart a trasaction which was stopped using the stop at block gap request.
|
||||
continue_req,
|
||||
17
|
||||
);
|
||||
register_bit!(
|
||||
control,
|
||||
/// Stop executing a transaction at the next block gap.
|
||||
stop_at_block_gap_req,
|
||||
16
|
||||
);
|
||||
register_bits_typed!(control, bus_voltage, u8, BusVoltage, 9, 11);
|
||||
register_bit!(control, bus_power, 8);
|
||||
register_bit!(
|
||||
control,
|
||||
/// Selects source for card detection. 0 for SDCD#, 1 for card detect test level.
|
||||
card_detect_signal,
|
||||
7
|
||||
);
|
||||
register_bit!(
|
||||
control,
|
||||
/// Indicates card inserted or not. Enabled when card detect signal is 1.
|
||||
card_detect_test_level,
|
||||
6
|
||||
);
|
||||
register_bits_typed!(control, dma_select, u8, DmaSelect, 3, 4);
|
||||
register_bit!(control, high_speed_en, 2);
|
||||
register_bit!(
|
||||
control,
|
||||
/// Select the data width of the HC. 1 for 4-bit, 0 for 1-bit.
|
||||
data_width_select,
|
||||
1
|
||||
);
|
||||
register_bit!(
|
||||
control,
|
||||
/// 1 for LED on, 0 for LED off.
|
||||
led_control,
|
||||
0
|
||||
);
|
||||
|
||||
register!(timing_control, TimingControl, RW, u32);
|
||||
register_bit!(
|
||||
timing_control,
|
||||
/// Software reset for DAT line.
|
||||
software_reset_dat,
|
||||
26
|
||||
);
|
||||
register_bit!(
|
||||
timing_control,
|
||||
/// Software reset for CMD line.
|
||||
software_reset_cmd,
|
||||
25
|
||||
);
|
||||
register_bit!(
|
||||
timing_control,
|
||||
/// Software reset for ALL.
|
||||
software_reset_all,
|
||||
24
|
||||
);
|
||||
register_bits!(
|
||||
timing_control,
|
||||
/// Determines the interval by which DAT line time-outs are detected.
|
||||
/// Interval = TMCLK * 2^(13 + val)
|
||||
/// Note: 0b1111 is reserved.
|
||||
timeout_counter_value,
|
||||
u8,
|
||||
16,
|
||||
19
|
||||
);
|
||||
register_bits_typed!(
|
||||
timing_control,
|
||||
/// Selects the frequency divisor, thus the clock frequency for SDCLK.
|
||||
/// Choose the smallest possible divisor which results in a clock frequency
|
||||
/// that is less than or equal to the target frequency.
|
||||
sdclk_freq_divisor,
|
||||
u8,
|
||||
SdclkFreqDivisor,
|
||||
8,
|
||||
15
|
||||
);
|
||||
register_bit!(timing_control, sd_clk_en, 2);
|
||||
register_bit!(
|
||||
timing_control,
|
||||
/// 1 when SD clock is stable.
|
||||
/// Note that this field is read-only.
|
||||
internal_clk_stable,
|
||||
1,
|
||||
RO
|
||||
);
|
||||
register_bit!(timing_control, internal_clk_en, 0);
|
||||
|
||||
register!(interrupt_status, InterruptStatus, RW, u32, 1 << 15 | 1 << 8);
|
||||
register_bit!(interrupt_status, ceata_error, 29, WTC);
|
||||
register_bit!(interrupt_status, target_response_error, 28, WTC);
|
||||
register_bit!(interrupt_status, adma_error, 25, WTC);
|
||||
register_bit!(interrupt_status, auto_cmd12_error, 24, WTC);
|
||||
register_bit!(interrupt_status, current_limit_error, 23, WTC);
|
||||
register_bit!(interrupt_status, data_end_bit_error, 22, WTC);
|
||||
register_bit!(interrupt_status, data_crc_error, 21, WTC);
|
||||
register_bit!(interrupt_status, data_timeout_error, 20, WTC);
|
||||
register_bit!(interrupt_status, command_index_error, 19, WTC);
|
||||
register_bit!(interrupt_status, command_end_bit_error, 18, WTC);
|
||||
register_bit!(interrupt_status, command_crc_error, 17, WTC);
|
||||
register_bit!(interrupt_status, command_timeout_error, 16, WTC);
|
||||
register_bit!(interrupt_status, error_interrupt, 15, RO);
|
||||
register_bit!(interrupt_status, boot_terminate_interrupt, 10, WTC);
|
||||
register_bit!(interrupt_status, boot_ack_rcv, 9, WTC);
|
||||
register_bit!(interrupt_status, card_interrupt, 8, RO);
|
||||
register_bit!(interrupt_status, card_removal, 7, WTC);
|
||||
register_bit!(interrupt_status, card_insertion, 6, WTC);
|
||||
register_bit!(interrupt_status, buffer_read_ready, 5, WTC);
|
||||
register_bit!(interrupt_status, buffer_write_ready, 4, WTC);
|
||||
register_bit!(interrupt_status, dma_interrupt, 3, WTC);
|
||||
register_bit!(interrupt_status, block_gap_event, 2, WTC);
|
||||
register_bit!(interrupt_status, transfer_complete, 1, WTC);
|
||||
register_bit!(interrupt_status, command_complete, 0, WTC);
|
||||
|
||||
register!(interrupt_status_en, InterruptStatusEn, RW, u32);
|
||||
register_bit!(interrupt_status_en, ceata_error_status_en, 29);
|
||||
register_bit!(interrupt_status_en, target_response_error_status_en, 28);
|
||||
register_bit!(interrupt_status_en, adma_error_status_en, 25);
|
||||
register_bit!(interrupt_status_en, auto_cmd12_error_status_en, 24);
|
||||
register_bit!(interrupt_status_en, current_limit_error_status_en, 23);
|
||||
register_bit!(interrupt_status_en, data_end_bit_error_status_en, 22);
|
||||
register_bit!(interrupt_status_en, data_crc_error_status_en, 21);
|
||||
register_bit!(interrupt_status_en, data_timeout_error_status_en, 20);
|
||||
register_bit!(interrupt_status_en, cmd_index_error_status_en, 19);
|
||||
register_bit!(interrupt_status_en, cmd_end_bit_error_status_en, 18);
|
||||
register_bit!(interrupt_status_en, cmd_crc_error_status_en, 17);
|
||||
register_bit!(interrupt_status_en, cmd_timeout_error_status_en, 16);
|
||||
register_bit!(interrupt_status_en, fixed_to_0, 15, RO);
|
||||
register_bit!(interrupt_status_en, boot_terminate_interrupt_en, 10);
|
||||
register_bit!(interrupt_status_en, boot_ack_rcv_en, 9);
|
||||
register_bit!(interrupt_status_en, card_interrupt_status_en, 8);
|
||||
register_bit!(interrupt_status_en, card_removal_status_en, 7);
|
||||
register_bit!(interrupt_status_en, card_insertion_status_en, 6);
|
||||
register_bit!(interrupt_status_en, buffer_read_ready_status_en, 5);
|
||||
register_bit!(interrupt_status_en, buffer_write_ready_status_en, 4);
|
||||
register_bit!(interrupt_status_en, dma_interrupt_status_en, 3);
|
||||
register_bit!(interrupt_status_en, block_gap_evt_status_en, 2);
|
||||
register_bit!(interrupt_status_en, transfer_complete_status_en, 1);
|
||||
register_bit!(interrupt_status_en, cmd_complete_status_en, 0);
|
||||
|
||||
register!(interrupt_signal_en, InterruptSignalEn, RW, u32);
|
||||
register_bit!(interrupt_signal_en, ceata_error_signal_en, 29);
|
||||
register_bit!(interrupt_signal_en, target_response_error_signal_en, 28);
|
||||
register_bit!(interrupt_signal_en, adma_error_signal_en, 25);
|
||||
register_bit!(interrupt_signal_en, auto_cmd12_error_signal_en, 24);
|
||||
register_bit!(interrupt_signal_en, current_limit_error_signal_en, 23);
|
||||
register_bit!(interrupt_signal_en, data_end_bit_error_signal_en, 22);
|
||||
register_bit!(interrupt_signal_en, data_crc_error_signal_en, 21);
|
||||
register_bit!(interrupt_signal_en, data_timeout_error_signal_en, 20);
|
||||
register_bit!(interrupt_signal_en, cmd_index_error_signal_en, 19);
|
||||
register_bit!(interrupt_signal_en, cmd_end_bit_error_signal_en, 18);
|
||||
register_bit!(interrupt_signal_en, cmd_crc_error_signal_en, 17);
|
||||
register_bit!(interrupt_signal_en, cmd_timeout_error_signal_en, 16);
|
||||
register_bit!(interrupt_signal_en, fixed_to_0, 15, RO);
|
||||
register_bit!(interrupt_signal_en, boot_terminate_interrupt_signal_en, 10);
|
||||
register_bit!(interrupt_signal_en, boot_ack_rcv_signal_en, 9);
|
||||
register_bit!(interrupt_signal_en, card_interrupt_signal_en, 8);
|
||||
register_bit!(interrupt_signal_en, card_removal_signal_en, 7);
|
||||
register_bit!(interrupt_signal_en, card_insertion_signal_en, 6);
|
||||
register_bit!(interrupt_signal_en, buffer_read_ready_signal_en, 5);
|
||||
register_bit!(interrupt_signal_en, buffer_write_ready_signal_en, 4);
|
||||
register_bit!(interrupt_signal_en, dma_interrupt_signal_en, 3);
|
||||
register_bit!(interrupt_signal_en, block_gap_evt_signal_en, 2);
|
||||
register_bit!(interrupt_signal_en, transfer_complete_signal_en, 1);
|
||||
register_bit!(interrupt_signal_en, cmd_complete_signal_en, 0);
|
||||
|
||||
register!(auto_cmd12_error_status, AutoCmd12ErrorStatus, RO, u32);
|
||||
register_bit!(
|
||||
auto_cmd12_error_status,
|
||||
cmd_not_issued_by_auto_cmd12_error,
|
||||
7
|
||||
);
|
||||
register_bit!(auto_cmd12_error_status, index_error, 4);
|
||||
register_bit!(auto_cmd12_error_status, end_bit_error, 3);
|
||||
register_bit!(auto_cmd12_error_status, crc_error, 2);
|
||||
register_bit!(auto_cmd12_error_status, timeout_error, 1);
|
||||
register_bit!(auto_cmd12_error_status, not_executed, 0);
|
||||
|
||||
register!(capabilities, Capabilities, RO, u32);
|
||||
register_bit!(capabilities, spi_block_mode, 30);
|
||||
register_bit!(capabilities, spi_mode, 29);
|
||||
register_bit!(capabilities, support_64bit, 28);
|
||||
register_bit!(capabilities, interrupt_mode, 27);
|
||||
register_bit!(capabilities, voltage_1_8, 26);
|
||||
register_bit!(capabilities, voltage_3_0, 25);
|
||||
register_bit!(capabilities, voltage_3_3, 24);
|
||||
register_bit!(capabilities, suspend_resume, 23);
|
||||
register_bit!(capabilities, sdma, 22);
|
||||
register_bit!(capabilities, hgih_speed, 21);
|
||||
register_bit!(capabilities, adma2, 19);
|
||||
register_bit!(capabilities, extended_media_bus, 18);
|
||||
register_bits!(
|
||||
capabilities,
|
||||
/// Length = 2^(9 + v) bytes.
|
||||
max_block_len,
|
||||
u8,
|
||||
16,
|
||||
17
|
||||
);
|
||||
register_bit!(capabilities, timeout_clock_unit, 7);
|
||||
|
||||
register!(max_current_capabilities, MaxCurrentCapabilities, RO, u32);
|
||||
register_bits!(max_current_capabilities, max_current_1_8v, u8, 16, 23);
|
||||
register_bits!(max_current_capabilities, max_current_3_0v, u8, 8, 15);
|
||||
register_bits!(max_current_capabilities, max_current_3_3v, u8, 0, 7);
|
||||
|
||||
register!(force_event, ForceEvent, WO, u32);
|
||||
register_bit!(force_event, ceata_error, 29);
|
||||
register_bit!(force_event, target_response_error, 28);
|
||||
register_bit!(force_event, adma_error, 25);
|
||||
register_bit!(force_event, auto_cmd12_error, 24);
|
||||
register_bit!(force_event, current_limit_error, 23);
|
||||
register_bit!(force_event, data_end_bit_error, 22);
|
||||
register_bit!(force_event, data_crc_error, 21);
|
||||
register_bit!(force_event, data_timeout_error, 20);
|
||||
register_bit!(force_event, cmd_index_error, 19);
|
||||
register_bit!(force_event, cmd_end_bit_error, 18);
|
||||
register_bit!(force_event, cmd_crc_error, 17);
|
||||
register_bit!(force_event, cmd_timeout_error, 16);
|
||||
register_bit!(force_event, cmd_not_issued_by_auto_cmd12_error, 7);
|
||||
register_bit!(force_event, auto_cmd12_index_error, 4);
|
||||
register_bit!(force_event, auto_cmd12_end_bit_error, 3);
|
||||
register_bit!(force_event, auto_cmd12_crc_error, 2);
|
||||
register_bit!(force_event, auto_cmd12_timeout_error, 1);
|
||||
register_bit!(force_event, auto_cmd12_not_executed, 0);
|
||||
|
||||
register!(adma_error_status, AdmaErrorStatus, RW, u32, 0b11);
|
||||
register_bit!(adma_error_status, length_mismatch_error, 2, WTC);
|
||||
register_bits_typed!(adma_error_status, error_state, u8, AdmaErrorState, 0, 1);
|
||||
|
||||
register!(debug_selection, DebugSelection, WO, u32);
|
||||
register_bit!(debug_selection, debug_select, 0);
|
||||
|
||||
register!(spi_interrupt_support, SpiInterruptSupport, RW, u32);
|
||||
register_bits!(
|
||||
spi_interrupt_support,
|
||||
/// There should be a problem with the documentation of this field.
|
||||
spi_int_support,
|
||||
u8,
|
||||
0,
|
||||
7
|
||||
);
|
||||
|
||||
register!(misc_reg, MiscReg, RO, u32);
|
||||
register_bits!(misc_reg, vendor_version_num, u8, 24, 31);
|
||||
register_bits_typed!(misc_reg, spec_ver, u8, SpecificationVersion, 16, 23);
|
||||
register_bits!(
|
||||
misc_reg,
|
||||
/// Logical OR of interrupt signal and wakeup signal for each slot.
|
||||
slot_interrupt_signal,
|
||||
u8,
|
||||
0,
|
||||
7
|
||||
);
|
||||
@ -100,6 +100,19 @@ macro_rules! register_rw {
|
||||
}
|
||||
}
|
||||
);
|
||||
($mod_name: ident, $struct_name: ident, $mask: expr) => (
|
||||
impl libregister::RegisterRW for $struct_name {
|
||||
#[inline]
|
||||
fn modify<F: FnOnce(Self::R, Self::W) -> Self::W>(&mut self, f: F) {
|
||||
unsafe {
|
||||
self.inner.modify(|inner| {
|
||||
f($mod_name::Read { inner }, $mod_name::Write { inner: inner & ($mask) })
|
||||
.inner
|
||||
});
|
||||
}
|
||||
}
|
||||
}
|
||||
);
|
||||
}
|
||||
|
||||
#[doc(hidden)]
|
||||
@ -168,6 +181,14 @@ macro_rules! register {
|
||||
libregister::register_common!($mod_name, $struct_name, VolatileCell<$inner>, $inner);
|
||||
libregister::register_vcell!($mod_name, $struct_name);
|
||||
);
|
||||
|
||||
// Define read-write register with mask on write (for WTC mixed access.)
|
||||
($mod_name: ident, $struct_name: ident, RW, $inner: ty, $mask: expr) => (
|
||||
libregister::register_common!($mod_name, $struct_name, volatile_register::RW<$inner>, $inner);
|
||||
libregister::register_r!($mod_name, $struct_name);
|
||||
libregister::register_w!($mod_name, $struct_name);
|
||||
libregister::register_rw!($mod_name, $struct_name, $mask);
|
||||
);
|
||||
}
|
||||
|
||||
/// Define a 1-bit field of a register
|
||||
@ -197,6 +218,47 @@ macro_rules! register_bit {
|
||||
}
|
||||
}
|
||||
);
|
||||
|
||||
// Single bit read-only
|
||||
($mod_name: ident, $(#[$outer:meta])* $name: ident, $bit: expr, RO) => (
|
||||
$(#[$outer])*
|
||||
impl $mod_name::Read {
|
||||
#[allow(unused)]
|
||||
#[inline]
|
||||
pub fn $name(&self) -> bool {
|
||||
use bit_field::BitField;
|
||||
|
||||
self.inner.get_bit($bit)
|
||||
}
|
||||
}
|
||||
);
|
||||
|
||||
// Single bit write to clear. Note that this must be used with WTC register.
|
||||
($mod_name: ident, $(#[$outer:meta])* $name: ident, $bit: expr, WTC) => (
|
||||
$(#[$outer])*
|
||||
impl $mod_name::Read {
|
||||
#[allow(unused)]
|
||||
#[inline]
|
||||
pub fn $name(&self) -> bool {
|
||||
use bit_field::BitField;
|
||||
|
||||
self.inner.get_bit($bit)
|
||||
}
|
||||
}
|
||||
|
||||
$(#[$outer])*
|
||||
impl $mod_name::Write {
|
||||
/// Clear bit field. (WTC)
|
||||
#[allow(unused)]
|
||||
#[inline]
|
||||
pub fn $name(mut self) -> Self {
|
||||
use bit_field::BitField;
|
||||
|
||||
self.inner.set_bit($bit, true);
|
||||
self
|
||||
}
|
||||
}
|
||||
);
|
||||
}
|
||||
|
||||
/// Define a multi-bit field of a register
|
||||
|
||||
Loading…
Reference in New Issue
Block a user