73 lines
3.1 KiB
Markdown
73 lines
3.1 KiB
Markdown
# Thermostat v1 prototype firmware
|
|
|
|
## Building
|
|
|
|
### On Debian-based systems
|
|
|
|
- install [rustup](https://rustup.rs/)
|
|
|
|
```shell
|
|
apt install gcc gcc-arm-none-eabi git-core
|
|
rustup toolchain install nightly
|
|
rustup update
|
|
rustup target add thumbv7em-none-eabihf --toolchain nightly
|
|
rustup default nightly
|
|
rustup component add rust-src
|
|
cargo install cargo-xbuild
|
|
git clone https://github.com/llvm/llvm-project.git
|
|
export RUST_COMPILER_RT_ROOT=`pwd`/llvm-project/compiler-rt
|
|
|
|
cd firmware && cargo xbuild --release
|
|
```
|
|
|
|
The built ELF file will be at `target/thumbv7em-none-eabihf/release/ionpak-firmware`
|
|
|
|
### Development build on NixOS
|
|
|
|
Requires NixOS 19.09 or later for cargo-xbuild.
|
|
|
|
```shell
|
|
nix-shell --run "cd firmware && cargo xbuild --release"
|
|
```
|
|
|
|
## Network
|
|
|
|
### Setup
|
|
|
|
Ethernet, IP: 192.168.1.26/24
|
|
|
|
Use telnet or netcat to connect to port 23/tcp (telnet)
|
|
|
|
### Reading ADC input
|
|
|
|
Set report mode to `once` to obtain the single next value. Report mode
|
|
will turn itself off after the next reading.
|
|
|
|
Set report mode to `continuous` for a continuous stream of input data.
|
|
|
|
The scope of this setting is per TCP session.
|
|
|
|
|
|
### Commands
|
|
|
|
| Syntax | Function |
|
|
| --- | --- |
|
|
| `report` | Show current input |
|
|
| `report mode` | Show current report mode |
|
|
| `report mode <off/on>` | Set report mode |
|
|
| `pwm <0/1> max_i_pos <width> <total>` | Set PWM duty cycle for **max_i_pos** to *width / total* |
|
|
| `pwm <0/1> max_i_neg <width> <total>` | Set PWM duty cycle for **max_i_neg** to *width / total* |
|
|
| `pwm <0/1> max_v <width> <total>` | Set PWM duty cycle for **max_v** to *width / total* |
|
|
| `pwm <0/1> <width> <total>` | Set PWM duty cycle for **i_set** to manual *width / total* |
|
|
| `pwm <0/1> pid` | Set PWM to be controlled by PID |
|
|
| `pid` | Show PID configuration |
|
|
| `pid <0/1> target <value>` | Set the PID controller target |
|
|
| `pid <0/1> kp <value>` | Set proportional gain |
|
|
| `pid <0/1> ki <value>` | Set integral gain |
|
|
| `pid <0/1> kd <value>` | Set differential gain |
|
|
| `pid <0/1> output_min <value>` | Set mininum output |
|
|
| `pid <0/1> output_max <value>` | Set maximum output |
|
|
| `pid <0/1> integral_min <value>` | Set integral lower bound |
|
|
| `pid <0/1> integral_max <value>` | Set integral upper bound |
|
|
| `postfilter <0/1> rate <rate>` | Set postfilter output data rate |
|