ionpak-thermostat/firmware
Astro 7efd42715e tec: enable GPIO pins for TEC SHDN 2019-11-10 22:27:20 +01:00
..
.cargo Update for latest nightly. 2018-08-28 19:57:17 +00:00
src tec: enable GPIO pins for TEC SHDN 2019-11-10 22:27:20 +01:00
Cargo.lock upgrade to current rust + smoltcp 2019-10-30 19:53:35 +01:00
Cargo.toml upgrade to current rust + smoltcp 2019-10-30 19:53:35 +01:00
README.md command_parser: shorten to parallel_r, add tests 2019-10-02 21:25:06 +02:00
build.rs build.rs: delint 2019-10-30 19:55:15 +01:00
memory.x Move firmware to firmware/. 2017-05-05 09:23:08 +00:00
openocd.cfg adapt OpenOCD script 2019-08-21 17:00:13 +08:00

README.md

Thermostat v1 prototype firmware

Building

On Debian-based systems

apt install gcc gcc-arm-none-eabi git-core
rustup toolchain install nightly
rustup update
rustup target add thumbv7em-none-eabihf --toolchain nightly
rustup default nightly
rustup component add rust-src
cargo install cargo-xbuild
git clone https://github.com/llvm/llvm-project.git
export RUST_COMPILER_RT_ROOT=`pwd`/llvm-project/compiler-rt

cd firmware && cargo xbuild --release

The built ELF file will be at target/thumbv7em-none-eabihf/release/ionpak-firmware

Development build on NixOS

Requires NixOS 19.09 or later for cargo-xbuild.

nix-shell --run "cd firmware && cargo xbuild --release"

Network

Setup

Ethernet, IP: 192.168.1.26/24

Use telnet or netcat to connect to port 23/tcp (telnet)

Reading ADC input

Set report mode to once to obtain the single next value. Report mode will turn itself off after the next reading.

Set report mode to continuous for a continuous stream of input data.

The scope of this setting is per TCP session.

Commands

Syntax Function
report Show current input
report mode Show current report mode
report mode <off/on> Set report mode
pwm <0/1> max_i_pos <width> <total> Set PWM duty cycle for max_i_pos to width / total
pwm <0/1> max_i_neg <width> <total> Set PWM duty cycle for max_i_neg to width / total
pwm <0/1> max_v <width> <total> Set PWM duty cycle for max_v to width / total
pwm <0/1> <width> <total> Set PWM duty cycle for i_set to manual width / total
pwm <0/1> pid Set PWM to be controlled by PID
pid Show PID configuration
pid <0/1> target <value> Set the PID controller target
pid <0/1> kp <value> Set proportional gain
pid <0/1> ki <value> Set integral gain
pid <0/1> kd <value> Set differential gain
pid <0/1> output_min <value> Set mininum output
pid <0/1> output_max <value> Set maximum output
pid <0/1> integral_min <value> Set integral lower bound
pid <0/1> integral_max <value> Set integral upper bound
s-h Show Steinhart-Hart equation parameters
s-h <0/1> <a/b/c> <value> Set Steinhart-Hart parameter for a channel
s-h <0/1> parallel_r <value> Set parallel resistance of the ADC
postfilter <0/1> rate <rate> Set postfilter output data rate