sinara-hw
/
datasheets
7
1
Fork 3
Code Issues 8 Pull Requests Projects Releases Wiki Activity
datasheets/4410-4412.tex

563 lines
23 KiB
TeX
Raw Blame History

\documentclass[10pt]{datasheet}
\usepackage{palatino}
\usepackage{textgreek}
\usepackage{minted}
\usepackage{tcolorbox}
\usepackage{etoolbox}
\BeforeBeginEnvironment{minted}{\begin{tcolorbox}[colback=white]}%
\AfterEndEnvironment{minted}{\end{tcolorbox}}%
\usepackage[justification=centering]{caption}
\usepackage[utf8]{inputenc}
\usepackage[english]{babel}
\usepackage[english]{isodate}
\usepackage{graphicx}
\usepackage{subfigure}
\usepackage{tikz}
\usepackage{pgfplots}
\usepackage{circuitikz}
\usetikzlibrary{calc}
\usetikzlibrary{fit,backgrounds}
\title{4410/4412 Urukul}
\author{M-Labs Limited}
\date{November 2021}
\revision{Revision 1}
\companylogo{\includegraphics[height=0.73in]{artiq_sinara.pdf}}
\begin{document}
\maketitle
\section{Features}
\begin{itemize}
\item{4 channels 1GS/s DDS.}
\item{Output frequency ranges from \textless 1 to \textgreater 400 MHz.}
\item{Sub-Hz frequency resolution.}
\item{Controlled phase steps.}
\item{Accurate output amplitude control.}
\end{itemize}
\section{Applications}
\begin{itemize}
\item{Agile local oscillator (LO) frequency synthesis.}
\item{Programmable clock generators.}
\item{Fast frequency hopping.}
\end{itemize}
\section{General Description}
The 4410/4412 Urukul card is a 4hp EEM module part of the ARTIQ Sinara family.
It adds frequency generation capabilities to carrier cards such as 1124 Kasli and 1125 Kasli-SoC.
It provides 4 channels of DDS at 1GS/s.
Output frequency from \textless 1 to \textgreater 400 MHz are supported.
The nominal maximum output power of each channel is 10dBm.
Each channel can be attenuated from 0 to -31.5 dB by a digital attenuator.
RF switches (1ns temporal resolution) on each channel provides 70 dB isolation.
4410 Urukul comes with AD9910 chips, while 4412 Urukul comes with AD9912 chips instead.
% Switch to next column
\vfill\break
\newcommand*{\MyLabel}[3][2cm]{\parbox{#1}{\centering #2 \\ #3}}
\newcommand*{\MymyLabel}[3][4cm]{\parbox{#1}{\centering #2 \\ #3}}
\begin{figure}[h]
\centering
\scalebox{0.88}{
\begin{circuitikz}[european, scale=0.95, every label/.append style={align=center}]
\begin{scope}[]
% Node to pin-point the locations of SMA symbols
\draw[color=white, text=black] (-0.1, 0) node[twoportshape, circuitikz/bipoles/twoport/width=1.2, scale=0.4 ] (ext_clk) {};
\draw[color=white, text=black] (-0.1, -0.35) node[twoportshape, circuitikz/bipoles/twoport/width=1.2, scale=0.4 ] (mmcx) {};
\draw[color=white, text=black] (-0.1, -1.75) node[twoportshape, circuitikz/bipoles/twoport/width=1.2, scale=0.4 ] (rf0) {};
\draw[color=white, text=black] (-0.1, -2.45) node[twoportshape, circuitikz/bipoles/twoport/width=1.2, scale=0.4 ] (rf1) {};
\draw[color=white, text=black] (-0.1, -3.15) node[twoportshape, circuitikz/bipoles/twoport/width=1.2, scale=0.4 ] (rf2) {};
\draw[color=white, text=black] (-0.1, -3.85) node[twoportshape, circuitikz/bipoles/twoport/width=1.2, scale=0.4 ] (rf3) {};
% Labels for female EXT_CLK, MMCX, RF {0, 1, 2, 3}
\node [label=left:\tiny{EXT CLK}] at (0.35, 0) {};
\node [label=left:\tiny{MMCX}] at (0.35, -0.35) {};
\node [label=left:\tiny{RF 0}] at (0.35, -1.75) {};
\node [label=left:\tiny{RF 1}] at (0.35, -2.45) {};
\node [label=left:\tiny{RF 2}] at (0.35, -3.15) {};
\node [label=left:\tiny{RF 3}] at (0.35, -3.85) {};
% draw female EXT_CLK, MMCX, RF {0, 1, 2, 3}
\begin{scope}[scale=0.07 , rotate=-90, xshift=0cm, yshift=2cm]
\draw (0,0.65) -- (0,3);
\clip (-1.5,0) rectangle (1.5,1.5);
\draw (0,0) circle(1.5);
\clip (-0.8,0) rectangle (0.8,0.8);
\draw (0,0) circle(0.8);
\end{scope}
\begin{scope}[scale=0.07 , rotate=-90, xshift=5cm, yshift=2cm]
\draw (0,0.65) -- (0,3);
\clip (-1.5,0) rectangle (1.5,1.5);
\draw (0,0) circle(1.5);
\clip (-0.8,0) rectangle (0.8,0.8);
\draw (0,0) circle(0.8);
\end{scope}
\begin{scope}[scale=0.07 , rotate=-90, xshift=25cm, yshift=2cm]
\draw (0,0.65) -- (0,3);
\clip (-1.5,0) rectangle (1.5,1.5);
\draw (0,0) circle(1.5);
\clip (-0.8,0) rectangle (0.8,0.8);
\draw (0,0) circle(0.8);
\end{scope}
\begin{scope}[scale=0.07 , rotate=-90, xshift=35cm, yshift=2cm]
\draw (0,0.65) -- (0,3);
\clip (-1.5,0) rectangle (1.5,1.5);
\draw (0,0) circle(1.5);
\clip (-0.8,0) rectangle (0.8,0.8);
\draw (0,0) circle(0.8);
\end{scope}
\begin{scope}[scale=0.07 , rotate=-90, xshift=45cm, yshift=2cm]
\draw (0,0.65) -- (0,3);
\clip (-1.5,0) rectangle (1.5,1.5);
\draw (0,0) circle(1.5);
\clip (-0.8,0) rectangle (0.8,0.8);
\draw (0,0) circle(0.8);
\end{scope}
\begin{scope}[scale=0.07 , rotate=-90, xshift=55cm, yshift=2cm]
\draw (0,0.65) -- (0,3);
\clip (-1.5,0) rectangle (1.5,1.5);
\draw (0,0) circle(1.5);
\clip (-0.8,0) rectangle (0.8,0.8);
\draw (0,0) circle(0.8);
\end{scope}
% Draw the internal oscillator
\draw (0.02, -0.8) node[twoportshape, t={OSC}, circuitikz/bipoles/twoport/width=0.8, scale=0.4] (xo) {};
% Draw the clock buffers as selector
% \tikzset{demux/.style={muxdemux, muxdemux def={Lh=6, Rh=6, NL=3, NT=1, NB=0, NR=1, w=2.5}, no input leads, scale=0.4}};
% \draw (1.55, -0.35) node[demux]{\rotatebox[origin=c]{-90}{CLK BUFFERS}};
\draw (1.45, -0.35) node[twoportshape, t={CLK Buffers}, circuitikz/bipoles/twoport/width=2.2, scale=0.4, rotate=-90] (clk_buf) {};
% Connect CLK_IN to DDS clock buffers
\draw [-latexslim] (ext_clk.east) -- ++(1,0);
\draw [-latexslim] (mmcx.east) -- ++(1,0);
\draw [-latexslim] (xo.east) -- ++(1,0);
% Connect CPLD clk_sel to DDS clock buffers
\draw [-latexslim] (clk_buf.east) -- ++(0,-0.42);
% Signal path: From control signals / clock of DDS to output of the RF switches
\draw (1.35, -1.75) node[twoportshape, t={DDS Signal Path}, circuitikz/bipoles/twoport/width=2, scale=0.4] (sig0) {};
\draw (1.35, -2.45) node[twoportshape, t={DDS Signal Path}, circuitikz/bipoles/twoport/width=2, scale=0.4] (sig1) {};
\draw (1.35, -3.15) node[twoportshape, t={DDS Signal Path}, circuitikz/bipoles/twoport/width=2, scale=0.4] (sig2) {};
\draw (1.35, -3.85) node[twoportshape, t={DDS Signal Path}, circuitikz/bipoles/twoport/width=2, scale=0.4] (sig3) {};
% Extra node to expand the dotted area eastward
\draw[color=white, text=black] (2.1, -3.85) node[twoportshape, circuitikz/bipoles/twoport/width=0.4, scale=0.4 ] (sig3_east) {};
% Connect RF to DDS block
\draw [latexslim-] (rf0.east) -- (sig0.west);
\draw [latexslim-] (rf1.east) -- (sig1.west);
\draw [latexslim-] (rf2.east) -- (sig2.west);
\draw [latexslim-] (rf3.east) -- (sig3.west);
% DDS signal path dotted area
\node[draw, dotted, thick, rounded corners, inner xsep=0.7em, inner ysep=0.4em, fit=(rf3)(sig0)(sig3_east.east)] (abs_dds) {};
\node[fill=white, rotate=-90, scale=0.7] at (abs_dds.west) {DDS Channels};
% CPLD
\draw (3.8, -0.35) node[twoportshape, t={CPLD}, circuitikz/bipoles/twoport/width=1.1, scale=0.8, rotate=-90] (cpld) {};
% Synthronization clock buffer for DDS block
\draw (3.5, -2.5) node[twoportshape, t=\MymyLabel{Sync}{Buffer}, circuitikz/bipoles/twoport/width=1.2, scale=0.5] (sync_buf) {};
% Connect CPLD to:
% DDS clock buffer
\draw [latexslim-] (clk_buf.north) -- (cpld.south);
% DDS signal path
\draw [latexslim-latexslim] (3.4, -0.7) -- ++ (-1.5, 0) -- ++ (0,-0.72);
% Draw to intersection point, then complete the connection to sync buffer
\draw [-] (4.2, -0.7) -- (4.55, -0.7) -- (4.55, -2.5);
\draw [-latexslim] (4.55, -2.5) -- (sync_buf.east);
% Connect sync buffer to DDS block
\draw [-latexslim] (sig0.east) -- (3.35, -1.75) -- ++ (0, -0.5);
\draw [-latexslim] (sync_buf.south) -- ++ (0, -0.3) -- ++ (-1.05, 0);
% LVDS Transceivers
\draw (6, 0) node[twoportshape, t=\MymyLabel{LVDS}{Transceiever}, circuitikz/bipoles/twoport/width=1.8, scale=0.5] (lvds0) {};
\draw (6, -0.7) node[twoportshape, t=\MymyLabel{LVDS}{Transceiever}, circuitikz/bipoles/twoport/width=1.8, scale=0.5] (lvds1) {};
\draw (6, -2.5) node[twoportshape, t=\MymyLabel{LVDS}{Transceiever}, circuitikz/bipoles/twoport/width=1.8, scale=0.5] (lvds2) {};
\draw (6, -3.2) node[twoportshape, t=\MymyLabel{LVDS}{Transceiever}, circuitikz/bipoles/twoport/width=1.8, scale=0.5] (lvds3) {};
% Connect CPLD to transceivers
\draw [latexslim-latexslim] (lvds0.west) -- ++ (-1.13, 0);
\draw [latexslim-latexslim] (lvds1.west) -- ++ (-0.35, 0) -- ++ (0, 0.6) -- ++ (-0.78, 0);
\draw [latexslim-latexslim] (lvds2.west) -- ++ (-0.45, 0) -- ++ (0, 2.3) -- ++ (-0.68, 0);
\draw [latexslim-latexslim] (lvds3.west) -- ++ (-0.55, 0) -- ++ (0, 2.9) -- ++ (-0.58, 0);
% EEPROMs
\draw (6, -1.4) node[twoportshape, t={EEPROM}, circuitikz/bipoles/twoport/width=1.8, scale=0.5] (eeprom0) {};
\draw (6, -3.9) node[twoportshape, t={EEPROM}, circuitikz/bipoles/twoport/width=1.8, scale=0.5] (eeprom1) {};
% Repeaters for DDS0 sync clock & DDS sync output from sync buffer
\draw (3.5, -3.85) node[twoportshape, t={Repeaters}, circuitikz/bipoles/twoport/width=1.2, scale=0.5] (rep) {};
% Connect DDS0 to repeaters
\draw [-latexslim] (sig0.east) -- ++ (0.3, 0) -- ++ (0, -1.55) -- (3.35, -3.3) -- ++ (0, -0.3);
% Connect sync_buf to repeaters
\draw [-latexslim] (sync_buf.south) -- ++ (0, -0.3) -- ++ (0.15, 0) -- ++ (0, -0.55);
% EEMs
\draw (8, -0.9) node[twoportshape, t={EEM Port 0}, circuitikz/bipoles/twoport/width=3.2, scale=0.5, rotate=-90] (eem0) {};
\draw (8, -3.4) node[twoportshape, t={EEM Port 1}, circuitikz/bipoles/twoport/width=3.2, scale=0.5, rotate=-90] (eem1) {};
% Connect LVDS and EEM
\draw [latexslim-latexslim] (lvds0.east) -- (7.75, 0);
\draw [latexslim-latexslim] (lvds1.east) -- (7.75, -0.7);
\draw [latexslim-latexslim] (lvds2.east) -- (7.75, -2.5);
\draw [latexslim-latexslim] (lvds3.east) -- (7.75, -3.2);
% Connect EEPROM to EEM
\draw [latexslim-latexslim] (eeprom0.east) -- (7.75, -1.4);
\draw [latexslim-latexslim] (eeprom1.east) -- (7.75, -3.9);
% Connect EEM0 to sync_buf
\draw [latexslim-] (3.65, -2.25) -- (3.65, -1.85) -- (7.75, -1.85);
% Connect repeaters output to EEM1
\draw [-latexslim] (rep.south) -- (3.5, -4.35) -- (7.75, -4.35);
% Synchronization ICs encased in another dotted area
\node[draw, dotted, thick, rounded corners, inner xsep=0.7em, inner ysep=0.4em, fit=(rep.south west)(sync_buf.north east)] (sync_path) {};
\node[fill=white, rotate=-90, scale=0.5] at (sync_path.east) {AD9910 Only};
\end{scope}
\end{circuitikz}
}
\caption{Simplified Block Diagram}
\end{figure}
\begin{figure}[h]
\centering
\scalebox{0.88}{
\begin{circuitikz}[european, scale=0.95, every label/.append style={align=center}]
\begin{scope}[]
% RF switches {0, 1, 2, 3} for SMA {0, 1, 2, 3}
\draw (1.4, 0) node[twoportshape, t={RF Switch}, circuitikz/bipoles/twoport/width=1.5, scale=0.6] (sw) {};
% Amplifiers {0, 1, 2, 3} for RF switches {0, 1, 2, 3}
\draw (3, 0) node[buffer, circuitikz/bipoles/twoport/width=1.2, scale=-0.5] (amp) {};
% Attenuators {0, 1, 2, 3} for amplifiers {0, 1, 2, 3}
\draw (4.6, 0) node[twoportshape, t=\MymyLabel{Digital}{Attenuator}, circuitikz/bipoles/twoport/width=2, scale=0.6, rotate=-90] (att) {};
% DDS {0, 1, 2, 3} for attenuators {0, 1, 2, 3}
\draw (6.6, 0) node[twoportshape, t={DDS}, circuitikz/bipoles/twoport/width=1.2, scale=0.7] (dds) {};
% Connect main signal path
\draw [-latexslim] (dds.west) -- (att.north);
\draw [-latexslim] (att.south) -- (amp.west);
\draw [-latexslim] (amp.east) -- (sw.east);
% Connect abstract DDS clock input
\node [label=above:\tiny{CLK Buffers}] at (8, -0.2) {};
\draw [latexslim-] (dds.east) -- (8, 0);
% Insert CPLD signal to relevant components
\node [label=above:\tiny{CPLD}] at (8, 1.1) {};
\draw [-] (1.4, 1.3) -- (8, 1.3);
\draw [-latexslim] (1.4, 1.3) -- (sw.north);
\draw [-latexslim] (4.6, 1.3) -- (att.west);
\draw [-latexslim] (6.6, 1.3) -- (dds.north);
% Connect sync_buf signal to DDS
\draw [latexslim-] (6.9, -1.35) -- (6.9, -0.35);
\draw [-latexslim] (6.3, -1.35) -- (6.3, -0.35);
\node [label=below:\tiny{Sync Buffer /}] at (6.6, -1.15) {};
\node [label=below:\tiny{Repeaters}] at (6.6, -1.4) {};
\node [label={[rotate=-90]above:\tiny{DDS 0}}] at (6.8, -0.9) {};
\node [label={[rotate=-90]above:\tiny{Only}}] at (6.55, -0.9) {};
\end{scope}
\end{circuitikz}
}
\caption{Simplified DDS Signal Path}
\end{figure}
\begin{figure}[h]
\centering
\includegraphics[width=1.78in]{photo4410.jpg}
\caption{Urukul Card photo}
\end{figure}
% For wide tables, a single column layout is better. It can be switched
% page-by-page.
\onecolumn
\section{Electrical Specifications}
\begin{table}[h]
\begin{threeparttable}
\caption{Recommended Operating Conditions}
\begin{tabularx}{\textwidth}{l | c | c c c | c | X}
\thickhline
\textbf{Parameter} & \textbf{Symbol} & \textbf{Min.} & \textbf{Typ.} & \textbf{Max.} &
\textbf{Unit} & \textbf{Conditions} \\
\hline
Clock input & & & & & &\\
\hspace{3mm} Input frequency & & 10 & & 1000 & MHz & PLL disabled \\
& & 3.2 & & 60 & MHz & AD9910, PLL enabled, no clock division \\
& & 12.8 & & 240 & MHz & AD9910, PLL enabled, 4x clock division \\
& & 11 & & 200 & MHz & AD9912, PLL enabled, no clock division \\
& & 44 & & 800 & MHz & AD9912, PLL enabled, 4x clock division \\
\hspace{3mm} Nominal input power & & & 10 & & dBm & \\
\thickhline
\end{tabularx}
\end{threeparttable}
\end{table}
\begin{table}[h]
\begin{threeparttable}
\caption{RF Output Specifications}
\begin{tabularx}{\textwidth}{l | c | c c c | c | X}
\thickhline
\textbf{Parameter} & \textbf{Symbol} & \textbf{Min.} & \textbf{Typ.} & \textbf{Max.} &
\textbf{Unit} & \textbf{Conditions} \\
\hline
Low frequency power & & & & -20 & dBm & 100 kHz output \\
& & & & 10 & dBm & 1 MHz output \\
\hline
Frequency & & 1 & & 400 & MHz & \\
\hline
Attenuation & & -31.5 & & 0 & dB & \\
\hline
Resolution & & & & & & \\
\hspace{3mm} Frequency & & & 0.25 & & Hz & AD9910 \\
& & & 8 & & $\mu$Hz & AD9912 \\
\hspace{3mm} Phase offset & & & 16 & & bits & AD9910 \\
& & & 14 & & bits & AD9912 \\
\hspace{3mm} Digital amplitude & & & 14 & & bits & AD9910 \\
\hspace{3mm} DAC full scale current & & & 8 & & bits & AD9910 \\
& & & 10 & & bits & AD9912 \\
\hspace{3mm} Temporal (I/O Update) & & & 4 & & ns & \\
\hspace{3mm} Digital attenuation & & & 0.5 & & dB & \\
\thickhline
\end{tabularx}
\end{threeparttable}
\end{table}
\newpage
All performance data are produced using the following setup unless otherwise noted.
\begin{itemize}
\item 100 MHz input clock into SMA, 10 dBm.
\item Input clock divided by 4.
\item PLL with x40 multiplier.
\item Output frequency at 80 MHz or 81 MHz.
\end{itemize}
\begin{table}[h]
\begin{threeparttable}
\caption{Electrical Characteristics}
\begin{tabularx}{\textwidth}{l | c | c c c | c | X}
\thickhline
\textbf{Parameter} & \textbf{Symbol} & \textbf{Min.} & \textbf{Typ.} & \textbf{Max.} &
\textbf{Unit} & \textbf{Conditions} \\
\hline
Digital attenuator glitch duration & & & 100 & & ns & \\
\hline
RF switch & & & & & &\\
\hspace{3mm} Rise to 90\% & $t_{on}$ & & 100 & & ns & \\
\hspace{3mm} Isolation & & & 70 & & dB & \\
\hspace{3mm} Turn-on chirp & $\gamma$ & & & 0.1 & deg/s & Excluding the first $\mu$s\\
\hline
Crosstalk & & & -84 & & dB & Victim RF switch opened \\
& & & -110 & & dB & Victim RF switch closed \\
\hline
Cross-channel-intermodulation & & & -90 & & dB & \\
\hline
Phase noise & & & -85 & & dBc/Hz & 0.1 Hz \\
& & & -95 & & dBc/Hz & 1 Hz \\
& & & -107 & & dBc/Hz & 10 Hz \\
& & & -116 & & dBc/Hz & 100 Hz \\
& & & -126 & & dBc/Hz & 1 kHz \\
& & & -133 & & dBc/Hz & 10 kHz \\
& & & -135 & & dBc/Hz & 100 kHz \\
& & & -128 & & dBc/Hz & 1 MHz \\
& & & -149 & & dBc/Hz & 10 MHz \\
\hline
Second-order harmonics & & & -40 & & dB & 6 dBm output \\
& & & -34 & & dB & 10.5 dBm output \\
\hline
Third-order harmonics & & & -54 & & dB & 6 dBm output \\
& & & -28 & & dB & 10.5 dBm output \\
\hline
Power consumption (AD9910) & & & 7 & & W & 4x 400 MHz, 10.5 dBm, 52\degree C\\
Power consumption (AD9912) & & & 6.5 & & W & 4x 400 MHz, 10.5 dBm, 52\degree C\\
\thickhline
\end{tabularx}
\end{threeparttable}
\end{table}
\newpage
\section{Example ARTIQ code}
The sections below demonstrate simple usage scenarios of the 4410 Urukul card with the ARTIQ control system.
They do not exhaustively demonstrate all the features of the ARTIQ system.
The full documentation for the ARTIQ software and gateware is available at \url{https://m-labs.hk}.
\subsection{10 MHz Sinusoidal Wave}
Generate a 10MHz sinusoid from RF0 with full scale amplitude, attenuated by 6 dB.
Both the CPLD and the DDS channels should be initialized.
By default, AD9910 single-tone profiles are programmed to profile 7.
\begin{minted}{python}
@kernel
def run(self):
self.core.reset()
self.cpld.init()
self.dds0.init()
self.dds0.cfg_sw(True)
self.dds0.set_att(6.*dB)
self.dds0.set(10*MHz)
\end{minted}
If the synchronization feature of AD9910 was enabled, RF signal across different channels of the same Urukul can be synchronized.
For example, phase-coherent RF signal can be produced on both channel 0 and channel 1 after configuring an appropriate phase mode.
\begin{minted}{python}
@kernel
def run(self):
self.core.reset()
self.cpld.init()
self.dds0.init()
self.dds0.cfg_sw(True)
self.dds0.set_phase_mode(PHASE_MODE_TRACKING)
self.dds0.set_att(6.*dB)
self.dds1.init()
self.dds1.cfg_sw(True)
self.dds1.set_phase_mode(PHASE_MODE_TRACKING)
self.dds1.set_att(6.*dB)
self.dds0.set(frequency=10*MHz, phase=0.0)
self.dds1.set(frequency=10*MHz, phase=0.25) # 0.25 turns phase offset
\end{minted}
Note that the phase difference between the 2 channels might not be exactly 0.25 turns, but it is a constant.
It can be negated by adjusting the \texttt{phase} parameter.
\newpage
\subsection{DDS RAM Modulation (AD9910 Only)}
This examples demonstrates that the RF signal can be modulated by amplitude using the RAM modulation feature of AD9910.
By default, RAM profiles are programmed to profile 0.
\begin{minted}{python}
from artiq.coredevice.ad9910 import RAM_MODE_CONT_RAMPUP
def prepare(self):
self.amp = [0.0, 0.0, 0.0, 0.7, 0.0, 0.7, 0.7] # Reversed Order
self.asf_ram = [0] * len(self.amp)
@kernel
def init_dds(self, dds):
self.core.break_realtime()
dds.init()
dds.set_att(6.*dB)
dds.cfg_sw(True)
@kernel
def configure_ram_mode(self, dds):
self.core.break_realtime()
dds.set_cfr1(ram_enable=0)
self.cpld.io_update.pulse_mu(8)
self.cpld.set_profile(0) # Enable the corresponding RAM profile
# Profile 0 is the default
dds.set_profile_ram(start=0, end=len(self.asf_ram)-1,
step=250, profile=0, mode=RAM_MODE_CONT_RAMPUP)
self.cpld.io_update.pulse_mu(8)
dds.amplitude_to_ram(self.amp, self.asf_ram)
dds.write_ram(self.asf_ram)
dds.set(frequency=10*MHz, ram_destination=RAM_DEST_ASF)
# Pass osk_enable=1 to set_cfr1() if it is not an amplitude RAM
dds.set_cfr1(ram_enable=1, ram_destination=RAM_DEST_ASF)
self.cpld.io_update.pulse_mu(8)
@kernel
def run(self):
self.core.reset()
self.core.break_realtime()
self.cpld.init()
self.init_dds(self.dds0)
self.configure_ram_mode(self.dds0)
\end{minted}
The generated RF output of the above example consists of the following features in sequence:
\begin{enumerate}
\item A 10 MHz RF pulse for 2 microseconds.
\item No signal for 1 microseconds.
\item A 10 MHz RF pulse for 1 microseconds.
\item No signal for 3 microseconds.
\item Go back to item 1.
\end{enumerate}
The expected waveform is plotted on the following figure.
\begin{figure}[h]
\centering
\includegraphics[width=\textwidth]{ad9910_amp_mod.png}
\caption{Expected waveform from the RAM modulation example}
\end{figure}
Multiple RAM channels can also be synchronized.
Similar to the 10 MHz single-tone RF signals, specify \texttt{phase} when calling \texttt{dds.set()} in \texttt{configure\char`_ram\char`_mode}.
For example, set phase to 0 for the channels (\texttt{phase=0.0}).
\begin{minted}{python}
dds.set(frequency=10*MHz, phase=0.0, ram_destination=RAM_DEST_ASF)
\end{minted}
Then, replace the \texttt{run()} function with the following.
\begin{minted}{python}
@kernel
def run(self):
self.core.reset()
self.core.break_realtime()
self.cpld.init()
self.init_dds(self.dds0)
self.init_dds(self.dds1)
self.dds0.set_phase_mode(PHASE_MODE_TRACKING)
self.dds1.set_phase_mode(PHASE_MODE_TRACKING)
self.configure_ram_mode(self.dds0)
self.configure_ram_mode(self.dds1)
\end{minted}
Two phase-coherent RF signal with the same waveform as the previous figure should be generated.
\newpage
\section{Ordering Information}
To order, please visit \url{https://m-labs.hk} and select the 4410 Urukul in the ARTIQ Sinara crate configuration tool.
The default chip is AD9910 (4410 Urukul), which supports more features.
If you need the higher frequency resolution of the AD9912 (4412 Urukul), leave us a note when placing the order.
The cards may also be ordered separately by writing to \url{mailto:sales@m-labs.hk}.
\section*{}
\vspace*{\fill}
\begin{footnotesize}
Information furnished by M-Labs Limited is believed to be accurate and reliable. However, no responsibility is assumed by M-Labs Limited for its use, nor for any infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice.
\end{footnotesize}
\end{document}
Reference in New Issue View Git Blame Copy Permalink