2008d02f4d
runtime: use different default IP and MAC for different kinds of boards
...
This helps reduce conflicts when having many boards on a development network.
2018-08-07 10:30:50 +08:00
bbe36b94f7
ad9154: enable sync in init
2018-08-06 19:02:27 +08:00
7f0b2ff594
jesd204sync: work around HMC7043 poor behavior with combined delays
...
The HMC7043 outputs poorly controlled signals when adjusting
two delays at once. This commit puts the DAC in one-shot SYSREF mode,
and only triggers synchronizations when SYSREF is stable.
2018-08-06 17:43:17 +08:00
f32f0126e2
Revert "ad9154: use continuous sync mode"
...
The HMC7043 is not really glitchless.
This reverts commit bd968211de
2018-08-06 16:59:53 +08:00
bd968211de
ad9154: use continuous sync mode
2018-08-06 00:27:10 +08:00
e83ee3a07a
hmc7043: disable GTP_CLK1 when not in use
...
Termination and biasing are not active at the FPGA when IBUFDS_GTE3 is
not instantiated, and driving a clock then leads to overvoltage.
2018-08-03 10:03:52 +08:00
6fc8439399
tweak moninj to allow old dashboard with new firmware
2018-08-02 19:34:14 +08:00
47740c8930
share moninj injection state between dashboards
...
Previously if one dashboard overrode a channel this was not visible on
any other dashboard - the channel appeared to operate normally.
2018-08-02 19:34:14 +08:00
whitequark
5871d13da8
firmware: actually compact in config::compact().
...
Fixes #1116 .
2018-08-01 16:27:48 +00:00
e4d48a78eb
drtio: wait for remote to ack TSC synchronization
...
Sayma takes a long time after TSC sync to align SYSREF, and this caused two issues:
1. Aux packets getting lost and causing error reports
2. DRTIO links reported up and kernels proceeding despite the DACs not being properly synced.
2018-07-26 20:28:17 +08:00
83de8b2ba2
drtio: add ping timeout during link init
2018-07-26 20:27:53 +08:00
446f791180
firmware: simplify SYSREF DRTIO alignment
2018-07-26 19:37:59 +08:00
f8c17528e7
satman: use new SYSREF code
2018-07-26 16:26:57 +08:00
32c95ac034
sayma: automated DAC SYSREF phase calibration
2018-07-26 16:23:55 +08:00
dbcf2fe9b4
firmware: remove 'chip found' messages on Sayma
2018-07-26 16:07:37 +08:00
d523d03f71
sayma: automated FPGA SYSREF phase offset calibration
2018-07-26 14:53:28 +08:00
0a9d3638ee
config: add write_int
2018-07-26 14:49:32 +08:00
19c51c644e
grabber: cleanup GRABBER_STATE
2018-07-24 19:08:51 +08:00
e71cbe53a6
firmware: cleanup Cargo.lock
2018-07-18 10:37:43 +08:00
13984385a8
firmware: version → ident
2018-07-15 17:40:17 +08:00
b27fa8964b
add variant in identifier string
...
Also add without-sawg suffixes on Sayma.
Closes #1060
Closes #1059
2018-07-15 17:21:17 +08:00
46fb5adac3
grabber: fix frequency counter formula
2018-07-12 20:14:38 +08:00
82def6b535
grabber: add frequency counter
...
Cameras are a bit obscure about what they output, this can help with troubleshooting.
2018-07-12 17:05:18 +08:00
29c35ee553
hmc7043: fix dumb mistake in previous commit
2018-07-12 13:01:41 +08:00
8802b930de
hmc7043: add delay after init
...
Delay required at step 9 of the "Typical Programming Sequence" (page 24 of the datasheet)
2018-07-12 12:37:12 +08:00
c66f9483f8
hmc7043: wait after changing delays
...
Allows for the SPI transaction to finish, and for the delay to stabilize.
2018-07-12 12:33:53 +08:00
1c191a62bf
sayma: tune SYSREF phases
2018-07-12 12:33:35 +08:00
773240bef4
hmc7043: test GPO before using
...
Based on code by David.
2018-07-12 11:30:24 +08:00
4843832329
hmc7043: check phase status on init. Closes #1055
...
Troubleshooting by David.
2018-07-11 19:45:24 +08:00
9397fa7f5a
hmc7043: unstick SYSREF FSM ( #1055 )
...
Troubleshooting by David.
Additionally, register 7D is broken.
Checking phase init state has to be done through another means.
2018-07-11 19:11:01 +08:00
4f56710e4b
grabber: add parser, report detected frame size in core device log
2018-07-10 02:06:37 +08:00
4eb26c0050
hmc7043: enable group 5
2018-07-03 14:16:31 +02:00
729ce58f98
sayma: use GTP_CLK1 to clock DRTIO satellite transceiver
...
This is required to get constant skew between the DRTIO transceiver clock
(which then generates the RTIO clock) and the siphaser reference clock.
Both the Si5324 and the RTM clock tree have non-deterministic in-to-out skew
at 150MHz due to dividers.
2018-06-28 11:23:40 +08:00
a65721d649
sayma: put RTM clock tree into the siphaser loop
...
* Fixes one bug where siphaser was one Si5324 output and the rest of the
system was clocked by the other. With the Si5324 settings we have, skew
between the outputs is not controlled.
* Puts the coaxial cable between AMC and RTM into the siphaser loop.
2018-06-27 21:46:55 +08:00
d49716dfac
satman: tune Sayma SYSREF phases
2018-06-27 18:09:35 +08:00
46c044099c
hmc7043,satman: verify alignment of SYSREF slips
2018-06-27 17:36:13 +08:00
7dfd70c502
hmc7043: make margin_{minus,plus} consistent with ad9154
2018-06-27 17:35:26 +08:00
4bbdd43bdf
hmc7043: do not freeze if SYSREF slip fails
2018-06-27 17:32:56 +08:00
a8a2ad68d3
runtime: tune Sayma SYSREF phases
2018-06-27 17:31:29 +08:00
84b3d9ecc6
bootloader: also check firmware CRC in SDRAM ( #1065 )
2018-06-23 11:28:12 +08:00
68530fde07
sayma: generate 100MHz from Si5324 on standalone and master targets
...
* Allow switching between DRTIO satellite and standalone without
touching the hardware.
* Allow operating standalone and master without an additional RF
signal generator.
2018-06-23 10:44:38 +08:00
whitequark
b6dd9c8bb0
runtime: support builds without RTIO DMA.
...
Fixes #1079 .
2018-06-23 00:56:21 +00:00
76fc63bbf7
jesd204: use separate controls for reset and input buffer disable
2018-06-22 11:38:18 +08:00
de7d64d482
sayma: clock JESD204 from GTP CLK2
...
This frees up GTP CLK1, which is routable to the SFP quads, for DRTIO.
2018-06-21 22:33:53 +08:00
07bcdfd91e
hmc7043: stricter check of FPGA SYSREF margin
2018-06-21 22:26:49 +08:00
e29536351d
drtio: resync SYSREF when TSC is loaded
2018-06-21 17:00:32 +08:00
5a2a857a2f
firmware: clean up SYSREF phase management
2018-06-21 16:23:41 +08:00
05e908a0fd
hmc7043: align SYSREF with RTIO
2018-06-21 15:54:42 +08:00
9741654cad
hmc7043: style
2018-06-21 15:54:42 +08:00
45e8263208
hmc7043: do not configure phases during initial init
...
They are determined later on.
2018-06-21 15:54:42 +08:00
