linuswck pushed to main at linuswck/INA848_INA849_Gain_Block

2024-05-08 15:40:45 +08:00

2992e608fd Finish rev0_1 design

linuswck pushed to main at linuswck/INA848_INA849_Gain_Block

2024-05-08 15:38:43 +08:00

3aa7711e9b Finish rev0_1 design

linuswck renamed repository from INA848_Gain_Block to linuswck/INA848_INA849_Gain_Block

2024-05-08 14:58:46 +08:00

linuswck created repository linuswck/INA848_INA849_Gain_Block

2024-05-08 14:53:49 +08:00

linuswck pushed to gui_dev at linuswck/thermostat

2024-05-08 13:24:54 +08:00

linuswck created branch gui_dev in linuswck/thermostat

2024-05-08 13:13:15 +08:00

linuswck pushed to gui_dev at linuswck/thermostat

2024-05-08 13:13:15 +08:00

4f9315f5fc test

linuswck commented on issue sinara-hw/kirdy#17

2024-05-06 17:37:34 +08:00

[TEST] LD Driver Current Noise

DUT Specs

300pA/rt Hz current noise @ 1kHz 300nA RMS Noise (10Hz - 1MHz)

Measurement Equipment

Keysight N9020a Noise Floor: ~9nV/sqrt(Hz) @ 1kHz (DC Coupling) (@100Hz Resolution)…

linuswck pushed to improve_adc_readings at linuswck/thermostat

2024-05-02 17:49:30 +08:00

8c1cb3117c README: Add notes on `i_tec` & `tec_i`readouts

linuswck created pull request M-Labs/thermostat#105

2024-05-02 17:45:30 +08:00

[WIP] Improve ADC Readings with Averaging Filter

linuswck created branch improve_adc_readings in linuswck/thermostat

2024-05-02 16:51:04 +08:00

linuswck pushed to improve_adc_readings at linuswck/thermostat

2024-05-02 16:51:04 +08:00

1fcfe41a63 Add averaging filter on the pin_adc readings

9fce19a418 Revert "Disable feedback current readout on flawed HW Revs"

Compare 2 commits »

linuswck created repository linuswck/thermostat

2024-05-02 13:18:37 +08:00

linuswck pushed to master at M-Labs/kirdy

2024-05-02 13:14:03 +08:00

e8aaf5f66b net: Implement iface polling timer

linuswck pushed to master at M-Labs/kirdy

2024-05-02 13:13:26 +08:00

4142519104 net: Implement iface polling timer

70fed23c51 main: Add checks before sock send/recv are called

Compare 2 commits »

linuswck opened issue sinara-hw/kirdy#44

2024-04-26 15:08:53 +08:00

[TEST] Laser Diode Current Output Temperature Coefficient

linuswck commented on pull request M-Labs/thermostat#101

2024-04-26 11:56:01 +08:00

GUI

Consider limiting the output current limit according to the specs(+-2A), I tried sourcing 3A into a TEC and Thermostat results in power failure. It…

linuswck commented on pull request M-Labs/thermostat#101

2024-04-25 17:46:09 +08:00

GUI

When thermostat is autotuning and the connected device is disconnected, then it will end up in this interface.

The control panel…

linuswck commented on pull request M-Labs/thermostat#101

2024-04-25 16:35:14 +08:00

GUI

If PID autotune finishes, there should be a message/diag box to notify the user.

linuswck created branch main in sinara-hw/kasli-pressfit

2024-04-24 18:08:13 +08:00