various control registers

This commit is contained in:
pca 2020-04-29 09:34:17 +08:00
parent 3238dae99f
commit b22cc4e2b6
1 changed files with 153 additions and 33 deletions

View File

@ -20,6 +20,41 @@ pub enum ResponseTypeSelect {
Legnth48Check = 0b11,
}
#[allow(unused)]
#[repr(u8)]
pub enum BusVoltage {
/// 3.3V
v33 = 0b111,
/// 3.0V, typ.
v30 = 0b110,
/// 1.8V, typ.
v18 = 0b101,
}
#[allow(unused)]
#[repr(u8)]
pub enum DmaSelect {
sdma = 0b00,
adma1 = 0b01,
adma2 = 0b10,
adma3 = 0b11,
}
#[allow(unused)]
#[repr(u8)]
/// SDCLK Frequency divisor, d(number) means baseclock divides by (number).
pub enum SdclkFreqDivisor {
d256 = 0x80,
d128 = 0x40,
d64 = 0x20,
d32 = 0x10,
d16 = 0x08,
d8 = 0x04,
d4 = 0x02,
d2 = 0x01,
d1 = 0x00,
}
#[repr(C)]
pub struct RegisterBlock {
pub sdma_system_address: RM<u32>,
@ -29,6 +64,10 @@ pub struct RegisterBlock {
pub responses: [RO<u32>; 4],
pub buffer: RW<u32>,
pub present_state: PresentState,
/// Host. power, block gap, wakeup control
pub control: Control,
/// Clock and timeout control, and software reset register.
pub timing_control: TimingControl,
}
register_at!(RegisterBlock, 0xE0100000, sd0);
@ -60,7 +99,6 @@ register_bits!(
11
);
register!(transfer_mode_command, TransferModeCommand, RW, u32);
register_bits!(
transfer_mode_command,
@ -137,7 +175,6 @@ register_bit!(
0
);
register!(present_state, PresentState, RO, u32);
register_bit!(
present_state,
@ -181,48 +218,131 @@ register_bit!(
card_detected,
18
);
regsiter_bit!(
present_state,
card_state_stable,
regsiter_bit!(present_state, card_state_stable, 17);
register_bit!(present_state, card_inserted, 16);
register_bit!(present_state, buffer_read_en, 11,);
register_bit!(present_state, buffer_write_en, 10);
register_bit!(present_state, read_transfer_active, 9);
register_bit!(present_state, write_transfer_active, 8);
register_bit!(present_state, dat_line_active, 2);
register_bit!(present_state, command_inhibit_dat, 1);
register_bit!(present_state, command_inhibit_cmd, 0);
register!(control, Control, RW, u32);
register_bit!(
contorl,
/// Enable wakeup event via SD card removal assertion.
wakeup_on_removal,
26
);
register_bit!(
control,
/// Enable wakeup event via SD card insertion assertion.
wakeup_on_insertion,
25
);
register_bit!(
control,
/// Enable wakeup event via card interrupt assertion.
wakeup_on_interrupt,
24
);
register_bit!(
control,
///Enable interrupt detection at the block gap for a multiple block transfer.
interrupt_at_block_gap,
19
);
register_bit!(
control,
/// Enable the use of the read wait protocol.
read_wait_control,
18
);
register_bit!(
control,
/// Restart a trasaction which was stopped using the stop at block gap request.
continue_req,
17
);
register_bit!(
present_state,
card_inserted,
control,
/// Stop executing a transaction at the next block gap.
stop_at_block_gap_req,
16
);
register_bits_typed!(control, bus_voltage, u8, BusVoltage, 9, 11);
register_bit!(control, bus_power, 8);
register_bit!(
present_state,
buffer_read_en,
11,
control,
/// Selects source for card detection. 0 for SDCD#, 1 for card detect test level.
card_detect_signal,
7
);
register_bit!(
present_state,
buffer_write_en,
10
control,
/// Indicates card inserted or not. Enabled when card detect signal is 1.
card_detect_test_level,
6
);
register_bits_typed!(control, dma_select, u8, DmaSelect, 3, 4);
register_bit!(control, high_speed_en, 2);
register_bit!(
present_state,
read_transfer_active,
9
);
register_bit!(
present_state,
write_transfer_active,
8
);
register_bit!(
present_state,
dat_line_active,
2
);
register_bit!(
present_state,
command_inhibit_dat,
control,
/// Select the data width of the HC. 1 for 4-bit, 0 for 1-bit.
data_width_select,
1
);
register_bit!(
present_state,
command_inhibit_cmd,
control,
/// 1 for LED on, 0 for LED off.
led_control,
0
);
register!(timing_control, TimingControl, RW, u32);
register_bit!(
timing_control,
/// Software reset for DAT line.
software_reset_dat,
26
);
register_bit!(
timing_control,
/// Software reset for CMD line.
software_reset_cmd,
25
);
register_bit!(
timing_control,
/// Software reset for ALL.
software_reset_all,
24
);
register_bits!(
timing_control,
/// Determines the interval by which DAT line time-outs are detected.
/// Interval = TMCLK * 2^(13 + val)
/// Note: 0b1111 is reserved.
timeout_counter_value,
u8,
16,
19
);
register_bits_typed!(
timing_control,
/// Selects the frequency divisor, thus the clock frequency for SDCLK.
/// Choose the smallest possible divisor which results in a clock frequency
/// that is less than or equal to the target frequency.
sdclk_freq_divisor,
u8,
SdclkFreqDivisor,
8,
15
);
register_bits!(timing_control, sd_clk_en, 2);
register_bits!(timing_control,
/// 1 when SD clock is stable.
/// Note that this field is read-only.
internal_clk_stable, 1);
register_bits!(timing_control, internal_clk_en, 0);