forked from M-Labs/humpback-dds
385 lines
11 KiB
Rust
385 lines
11 KiB
Rust
#![no_main]
|
|
#![no_std]
|
|
|
|
use core::sync::atomic::{AtomicU32, Ordering};
|
|
|
|
// extern crate cortex_m;
|
|
use panic_semihosting as _;
|
|
|
|
use cortex_m;
|
|
use cortex_m::asm::nop;
|
|
use cortex_m_rt::{
|
|
entry,
|
|
exception,
|
|
};
|
|
use cortex_m_semihosting::hprintln;
|
|
|
|
extern crate smoltcp;
|
|
|
|
use stm32h7xx_hal::ethernet;
|
|
use stm32h7xx_hal::gpio::Speed;
|
|
use stm32h7xx_hal::hal::digital::v2::{
|
|
OutputPin,
|
|
InputPin,
|
|
};
|
|
use stm32h7xx_hal::rcc::CoreClocks;
|
|
use stm32h7xx_hal::{pac, prelude::*, spi, stm32, stm32::interrupt};
|
|
use Speed::*;
|
|
|
|
use libm::round;
|
|
|
|
use core::{
|
|
str,
|
|
fmt::Write
|
|
};
|
|
use core::mem::uninitialized;
|
|
|
|
use smoltcp::wire::{EthernetAddress, IpAddress, IpCidr, Ipv4Address};
|
|
use smoltcp::iface::{NeighborCache, EthernetInterfaceBuilder, Routes};
|
|
use smoltcp::socket::SocketSet;
|
|
use smoltcp::socket::{SocketHandle, TcpSocket, TcpSocketBuffer};
|
|
use smoltcp::time::{Duration, Instant};
|
|
|
|
use embedded_nal::TcpStack;
|
|
|
|
use firmware;
|
|
use firmware::{
|
|
attenuator::Attenuator,
|
|
config_register::{
|
|
ConfigRegister,
|
|
CFGMask,
|
|
StatusMask,
|
|
},
|
|
dds::{
|
|
DDS,
|
|
DDSCFRMask,
|
|
},
|
|
cpld::{
|
|
CPLD,
|
|
},
|
|
Urukul,
|
|
};
|
|
use scpi::prelude::*;
|
|
|
|
/// Configure SYSTICK for 1ms timebase
|
|
fn systick_init(syst: &mut stm32::SYST, clocks: CoreClocks) {
|
|
let c_ck_mhz = clocks.c_ck().0 / 1_000_000;
|
|
|
|
let syst_calib = 0x3E8;
|
|
|
|
syst.set_clock_source(cortex_m::peripheral::syst::SystClkSource::Core);
|
|
syst.set_reload((syst_calib * c_ck_mhz) - 1);
|
|
syst.enable_interrupt();
|
|
syst.enable_counter();
|
|
}
|
|
|
|
/// ======================================================================
|
|
/// Entry point
|
|
/// ======================================================================
|
|
|
|
/// TIME is an atomic u32 that counts milliseconds. Although not used
|
|
/// here, it is very useful to have for network protocols
|
|
static TIME: AtomicU32 = AtomicU32::new(0);
|
|
|
|
/// Locally administered MAC address
|
|
const MAC_ADDRESS: [u8; 6] = [0x02, 0x00, 0x11, 0x22, 0x33, 0x44];
|
|
|
|
/// Ethernet descriptor rings are a global singleton
|
|
#[link_section = ".sram3.eth"]
|
|
static mut DES_RING: ethernet::DesRing = ethernet::DesRing::new();
|
|
|
|
// Theoratical maximum number of socket that can be handled
|
|
const SOCKET_COUNT: usize = 2;
|
|
|
|
// Give buffer sizes of transmitting and receiving TCP packets
|
|
const BUFFER_SIZE: usize = 2048;
|
|
|
|
// the program entry point
|
|
#[entry]
|
|
fn main() -> ! {
|
|
|
|
let mut cp = cortex_m::Peripherals::take().unwrap();
|
|
let dp = pac::Peripherals::take().unwrap();
|
|
|
|
// Initialise power...
|
|
let pwr = dp.PWR.constrain();
|
|
let vos = pwr.freeze();
|
|
|
|
// Initialise SRAM3
|
|
dp.RCC.ahb2enr.modify(|_, w| w.sram3en().set_bit());
|
|
|
|
// Initialise clocks...
|
|
let rcc = dp.RCC.constrain();
|
|
let ccdr = rcc
|
|
.sys_ck(200.mhz())
|
|
.hclk(200.mhz())
|
|
.pll1_r_ck(100.mhz()) // for TRACECK
|
|
.pll1_q_ck(48.mhz()) // for SPI
|
|
.freeze(vos, &dp.SYSCFG);
|
|
|
|
// Get the delay provider.
|
|
let delay = cp.SYST.delay(ccdr.clocks);
|
|
|
|
// Initialise system...
|
|
cp.SCB.invalidate_icache();
|
|
cp.SCB.enable_icache();
|
|
// TODO: ETH DMA coherence issues
|
|
// cp.SCB.enable_dcache(&mut cp.CPUID);
|
|
cp.DWT.enable_cycle_counter();
|
|
|
|
// Initialise IO...
|
|
let gpioa = dp.GPIOA.split(ccdr.peripheral.GPIOA);
|
|
let gpiob = dp.GPIOB.split(ccdr.peripheral.GPIOB);
|
|
let gpioc = dp.GPIOC.split(ccdr.peripheral.GPIOC);
|
|
let gpiod = dp.GPIOD.split(ccdr.peripheral.GPIOD);
|
|
let gpioe = dp.GPIOE.split(ccdr.peripheral.GPIOE);
|
|
let gpiof = dp.GPIOF.split(ccdr.peripheral.GPIOF);
|
|
let gpiog = dp.GPIOG.split(ccdr.peripheral.GPIOG);
|
|
// let mut link_led = gpiob.pb0.into_push_pull_output(); // LED1, green
|
|
// let mut status_led = gpioe.pe1.into_push_pull_output(); // LD2, yellow
|
|
// let mut listen_led = gpiob.pb14.into_push_pull_output(); // LD3, red
|
|
// link_led.set_low().ok();
|
|
// status_led.set_low().ok();
|
|
// listen_led.set_low().ok();
|
|
|
|
// Setup CDONE for checking
|
|
let fpga_cdone = gpiod.pd15.into_pull_up_input();
|
|
|
|
match fpga_cdone.is_high() {
|
|
Ok(true) => hprintln!("FPGA is ready."),
|
|
Ok(_) => hprintln!("FPGA is in reset state."),
|
|
Err(_) => hprintln!("Error: Cannot read C_DONE"),
|
|
}.unwrap();
|
|
|
|
// Setup Urukul
|
|
/*
|
|
* Using SPI1, AF5
|
|
* SCLK -> PA5
|
|
* MOSI -> PB5
|
|
* MISO -> PA6
|
|
* CS -> 0: PB12, 1: PA15, 2: PC7
|
|
*/
|
|
|
|
let sclk = gpioa.pa5.into_alternate_af5();
|
|
let mosi = gpiob.pb5.into_alternate_af5();
|
|
let miso = gpioa.pa6.into_alternate_af5();
|
|
|
|
|
|
let (cs0, cs1, cs2) = (
|
|
gpiob.pb12.into_push_pull_output(),
|
|
gpioa.pa15.into_push_pull_output(),
|
|
gpioc.pc7.into_push_pull_output(),
|
|
);
|
|
|
|
/*
|
|
* I/O_Update -> PB15
|
|
*/
|
|
let io_update = gpiob.pb15.into_push_pull_output();
|
|
|
|
let spi = dp.SPI1.spi(
|
|
(sclk, miso, mosi),
|
|
spi::MODE_0,
|
|
3.mhz(),
|
|
ccdr.peripheral.SPI1,
|
|
&ccdr.clocks,
|
|
);
|
|
|
|
let switch = CPLD::new(spi, (cs0, cs1, cs2), io_update);
|
|
let parts = switch.split();
|
|
let mut urukul = Urukul::new(
|
|
parts.spi1, parts.spi2, parts.spi3, parts.spi4, parts.spi5, parts.spi6, parts.spi7,
|
|
[25_000_000, 25_000_000, 25_000_000, 25_000_000]
|
|
);
|
|
|
|
// Setup ethernet pins
|
|
setup_ethernet_pins(
|
|
gpioa.pa1, gpioa.pa2, gpioc.pc1, gpioa.pa7, gpioc.pc4,
|
|
gpioc.pc5, gpiog.pg11, gpiog.pg13, gpiob.pb13
|
|
);
|
|
|
|
// Initialise ethernet...
|
|
assert_eq!(ccdr.clocks.hclk().0, 200_000_000); // HCLK 200MHz
|
|
assert_eq!(ccdr.clocks.pclk1().0, 100_000_000); // PCLK 100MHz
|
|
assert_eq!(ccdr.clocks.pclk2().0, 100_000_000); // PCLK 100MHz
|
|
assert_eq!(ccdr.clocks.pclk4().0, 100_000_000); // PCLK 100MHz
|
|
|
|
let mac_addr = smoltcp::wire::EthernetAddress::from_bytes(&MAC_ADDRESS);
|
|
let (_eth_dma, mut eth_mac) = unsafe {
|
|
ethernet::new_unchecked(
|
|
dp.ETHERNET_MAC,
|
|
dp.ETHERNET_MTL,
|
|
dp.ETHERNET_DMA,
|
|
&mut DES_RING,
|
|
mac_addr.clone(),
|
|
)
|
|
};
|
|
unsafe {
|
|
ethernet::enable_interrupt();
|
|
cp.NVIC.set_priority(stm32::Interrupt::ETH, 196); // Mid prio
|
|
cortex_m::peripheral::NVIC::unmask(stm32::Interrupt::ETH);
|
|
}
|
|
|
|
// ----------------------------------------------------------
|
|
// Begin periodic tasks
|
|
|
|
systick_init(&mut delay.free(), ccdr.clocks);
|
|
unsafe {
|
|
cp.SCB.shpr[15 - 4].write(128);
|
|
} // systick exception priority
|
|
|
|
// ----------------------------------------------------------
|
|
// Main application loop
|
|
|
|
// Setup addresses, maybe not MAC?
|
|
// MAC is set up in prior
|
|
let local_addr = IpAddress::v4(192, 168, 1, 200);
|
|
let mut ip_addrs = [IpCidr::new(local_addr, 24)];
|
|
|
|
// let neighbor_cache = NeighborCache::new(BTreeMap::new());
|
|
let mut neighbor_storage = [None; 16];
|
|
let neighbor_cache = NeighborCache::new(&mut neighbor_storage[..]);
|
|
|
|
// Routes
|
|
let default_v4_gw = Ipv4Address::new(192, 168, 1, 1);
|
|
let mut routes_storage = [None; 8];
|
|
let mut routes = Routes::new(&mut routes_storage[..]);
|
|
routes.add_default_ipv4_route(default_v4_gw).unwrap();
|
|
|
|
// Device? _eth_dma, as it implements phy::device
|
|
let mut iface = EthernetInterfaceBuilder::new(_eth_dma)
|
|
.ethernet_addr(mac_addr)
|
|
.neighbor_cache(neighbor_cache)
|
|
.ip_addrs(&mut ip_addrs[..])
|
|
.routes(routes)
|
|
.finalize();
|
|
|
|
// SCPI configs
|
|
// Device was declared in prior
|
|
|
|
// let mut errors = ArrayErrorQueue::<[Error; 10]>::new();
|
|
// let mut context = Context::new(&mut urukul, &mut errors, TREE);
|
|
|
|
// //Response bytebuffer
|
|
// let mut buf = ArrayVecFormatter::<[u8; 256]>::new();
|
|
|
|
// SCPI configs END
|
|
|
|
// TCP socket
|
|
let server_socket = {
|
|
static mut server_rx_storage :[u8; BUFFER_SIZE] = [0; BUFFER_SIZE];
|
|
static mut server_tx_storage :[u8; BUFFER_SIZE] = [0; BUFFER_SIZE];
|
|
let server_rx_buffer = TcpSocketBuffer::new( unsafe { &mut server_rx_storage[..] } );
|
|
let server_tx_buffer = TcpSocketBuffer::new( unsafe { &mut server_tx_storage[..] } );
|
|
TcpSocket::new(server_rx_buffer, server_tx_buffer)
|
|
};
|
|
|
|
// Setup a silent socket
|
|
let client_socket = {
|
|
static mut client_rx_storage :[u8; BUFFER_SIZE] = [0; BUFFER_SIZE];
|
|
static mut client_tx_storage :[u8; BUFFER_SIZE] = [0; BUFFER_SIZE];
|
|
let client_rx_buffer = TcpSocketBuffer::new( unsafe { &mut client_rx_storage[..] } );
|
|
let client_tx_buffer = TcpSocketBuffer::new( unsafe { &mut client_tx_storage[..] } );
|
|
TcpSocket::new(client_rx_buffer, client_tx_buffer)
|
|
};
|
|
|
|
// Socket storage
|
|
let mut sockets_storage: [_; 2] = Default::default();
|
|
|
|
let mut socket_set = SocketSet::new(&mut sockets_storage[..]);
|
|
let server_handle = socket_set.add(server_socket);
|
|
let client_handle = socket_set.add(client_socket);
|
|
|
|
loop {
|
|
let _time = TIME.load(Ordering::Relaxed);
|
|
match iface.poll(&mut socket_set, Instant::from_millis(_time as i64)) {
|
|
Ok(_) => {
|
|
// hprintln!("Ethernet up").unwrap();
|
|
},
|
|
Err(e) => {
|
|
hprintln!("Ethernet down!").unwrap();
|
|
},
|
|
};
|
|
|
|
// Conenct to TCP server through port 49500
|
|
{
|
|
let mut socket = socket_set.get::<TcpSocket>(server_handle);
|
|
if !socket.is_active() && !socket.is_listening(){
|
|
socket.listen(7777).unwrap();
|
|
hprintln!("Server listening").unwrap();
|
|
}
|
|
|
|
// hprintln!("listener state :{}", socket.state()).unwrap();
|
|
|
|
if socket.can_recv() {
|
|
hprintln!("{:?}", str::from_utf8(socket.recv(|data| {
|
|
(data.len(), data)
|
|
}).unwrap()).unwrap()).unwrap();
|
|
}
|
|
}
|
|
|
|
{
|
|
let mut socket = socket_set.get::<TcpSocket>(client_handle);
|
|
if !socket.is_open() {
|
|
socket.abort();
|
|
socket.close();
|
|
hprintln!("reset state: {}", socket.state()).unwrap();
|
|
socket.connect((IpAddress::v4(192, 168, 1, 200), 1883),
|
|
(IpAddress::Unspecified, 45000)).unwrap();
|
|
hprintln!("post connect state: {}", socket.state()).unwrap();
|
|
}
|
|
|
|
// hprintln!("client state: {}", socket.state()).unwrap();
|
|
|
|
if socket.can_send() {
|
|
socket.send_slice(b"regards from socket").unwrap();
|
|
}
|
|
}
|
|
}
|
|
}
|
|
|
|
use stm32h7xx_hal::gpio::{
|
|
gpioa::{PA1, PA2, PA7},
|
|
gpiob::{PB13},
|
|
gpioc::{PC1, PC4, PC5},
|
|
gpiog::{PG11, PG13},
|
|
Speed::VeryHigh,
|
|
};
|
|
|
|
/*
|
|
* Migrated ethernet setup pins
|
|
*/
|
|
pub fn setup_ethernet_pins<REF_CLK, MDIO, MDC, CRS_DV, RXD0, RXD1, TX_EN, TXD0, TXD1>(
|
|
pa1: PA1<REF_CLK>, pa2: PA2<MDIO>, pc1: PC1<MDC>, pa7: PA7<CRS_DV>, pc4: PC4<RXD0>,
|
|
pc5: PC5<RXD1>, pg11: PG11<TX_EN>, pg13: PG13<TXD0>, pb13: PB13<TXD1>
|
|
) {
|
|
pa1.into_alternate_af11().set_speed(VeryHigh);
|
|
pa2.into_alternate_af11().set_speed(VeryHigh);
|
|
pc1.into_alternate_af11().set_speed(VeryHigh);
|
|
pa7.into_alternate_af11().set_speed(VeryHigh);
|
|
pc4.into_alternate_af11().set_speed(VeryHigh);
|
|
pc5.into_alternate_af11().set_speed(VeryHigh);
|
|
pg11.into_alternate_af11().set_speed(VeryHigh);
|
|
pg13.into_alternate_af11().set_speed(VeryHigh);
|
|
pb13.into_alternate_af11().set_speed(VeryHigh);
|
|
}
|
|
|
|
#[interrupt]
|
|
fn ETH() {
|
|
unsafe { ethernet::interrupt_handler() }
|
|
}
|
|
|
|
#[exception]
|
|
fn SysTick() {
|
|
TIME.fetch_add(1, Ordering::Relaxed);
|
|
}
|
|
|
|
#[exception]
|
|
fn HardFault(ef: &cortex_m_rt::ExceptionFrame) -> ! {
|
|
panic!("HardFault at {:#?}", ef);
|
|
}
|
|
|
|
#[exception]
|
|
fn DefaultHandler(irqn: i16) {
|
|
panic!("Unhandled exception (IRQn = {})", irqn);
|
|
}
|