README.md

@@ -271,7 +271,7 @@ with the following keys.
 | `tec_u_meas`   | Volts           | Measurement of the voltage across the TEC            |
 | `pid_output`   | Amperes         | PID control output                                   |
 
-Note: With Thermostat v2 and below, the voltage and current readouts `i_tec` and `tec_i` are noisy without the hardware fix shown in [this PR][https://git.m-labs.hk/M-Labs/thermostat/pulls/105].
+Note: With Thermostat v2 and below, the voltage and current readouts `i_tec` and `tec_i` are disabled and null due to faulty hardware that introduces a lot of noise in the signal.
 
 ## PID Tuning
 

src/channels.rs

@@ -1,6 +1,5 @@
-use core::{cmp::max_by, marker::PhantomData};
+use core::cmp::max_by;
 use heapless::{consts::U2, Vec};
-use num_traits::Zero;
 use serde::{Serialize, Serializer};
 use smoltcp::time::Instant;
 use stm32f4xx_hal::hal;
@@ -19,50 +18,29 @@ use crate::{
     channel_state::ChannelState,
     command_parser::{CenterPoint, PwmPin},
     command_handler::JsonBuffer,
-    pins::{self, Channel0VRef, Channel1VRef},
+    pins,
     steinhart_hart,
+    hw_rev,
 };
 
-pub enum PinsAdcReadTarget {
-    VREF,
-    DacVfb,
-    ITec,
-    VTec,
-}
-
 pub const CHANNELS: usize = 2;
 pub const R_SENSE: f64 = 0.05;
-
-// From design specs
-pub const MAX_TEC_I: ElectricCurrent = ElectricCurrent {
-    dimension: PhantomData,
-    units: PhantomData,
-    value: 2.0,
-};
-pub const MAX_TEC_V: ElectricPotential = ElectricPotential {
-    dimension: PhantomData,
-    units: PhantomData,
-    value: 4.0,
-};
-
 // DAC chip outputs 0-5v, which is then passed through a resistor dividor to provide 0-3v range
-const DAC_OUT_V_MAX: ElectricPotential = ElectricPotential {
+const DAC_OUT_V_MAX: f64 = 3.0;
-    dimension: PhantomData,
+
-    units: PhantomData,
-    value: 3.0,
-};
 // TODO: -pub
-pub struct Channels {
+pub struct Channels<'a> {
     channel0: Channel<Channel0>,
     channel1: Channel<Channel1>,
     pub adc: ad7172::Adc<pins::AdcSpi, pins::AdcNss>,
     /// stm32f4 integrated adc
     pins_adc: pins::PinsAdc,
     pub pwm: pins::PwmPins,
+    hwrev: &'a hw_rev::HWRev,
 }
 
-impl Channels {
+impl<'a> Channels<'a> {
-    pub fn new(pins: pins::Pins) -> Self {
+    pub fn new(pins: pins::Pins, hwrev: &'a hw_rev::HWRev) -> Self {
         let mut adc = ad7172::Adc::new(pins.adc_spi, pins.adc_nss).unwrap();
         // Feature not used
         adc.set_sync_enable(false).unwrap();
@@ -80,7 +58,7 @@ impl Channels {
         let channel1 = Channel::new(pins.channel1, adc_calibration1);
         let pins_adc = pins.pins_adc;
         let pwm = pins.pwm;
-        let mut channels = Channels { channel0, channel1, adc, pins_adc, pwm };
+        let mut channels = Channels { channel0, channel1, adc, pins_adc, pwm, hwrev };
         for channel in 0..CHANNELS {
             channels.calibrate_dac_value(channel);
             channels.set_i(channel, ElectricCurrent::new::<ampere>(0.0));
@@ -122,7 +100,7 @@ impl Channels {
     pub fn get_center(&mut self, channel: usize) -> ElectricPotential {
         match self.channel_state(channel).center {
             CenterPoint::Vref =>
-                self.adc_read(channel, PinsAdcReadTarget::VREF, 8),
+                self.read_vref(channel),
             CenterPoint::Override(center_point) =>
                 ElectricPotential::new::<volt>(center_point.into()),
         }
@@ -141,7 +119,7 @@ impl Channels {
 
     /// i_set DAC
     fn set_dac(&mut self, channel: usize, voltage: ElectricPotential) -> ElectricPotential {
-        let value = ((voltage / DAC_OUT_V_MAX).get::<ratio>() * (ad5680::MAX_VALUE as f64)) as u32 ;
+        let value = ((voltage / ElectricPotential::new::<volt>(DAC_OUT_V_MAX)).get::<ratio>() * (ad5680::MAX_VALUE as f64)) as u32 ;
         match channel {
             0 => self.channel0.dac.set(value).unwrap(),
             1 => self.channel1.dac.set(value).unwrap(),
@@ -152,7 +130,6 @@ impl Channels {
     }
 
     pub fn set_i(&mut self, channel: usize, i_set: ElectricCurrent) -> ElectricCurrent {
-        let i_set = i_set.min(MAX_TEC_I).max(-MAX_TEC_I);
         let vref_meas = match channel.into() {
             0 => self.channel0.vref_meas,
             1 => self.channel1.vref_meas,
@@ -167,112 +144,32 @@ impl Channels {
         i_set
     }
 
-    /// AN4073: ADC Reading Dispersion can be reduced through Averaging
+    pub fn read_dac_feedback(&mut self, channel: usize) -> ElectricPotential {
-    pub fn adc_read(&mut self, channel: usize, adc_read_target: PinsAdcReadTarget, avg_pt: u16) -> ElectricPotential {
-        let mut sample: u32 = 0;
         match channel {
             0 => {
-                sample = match adc_read_target {
+                let sample = self.pins_adc.convert(
-                    PinsAdcReadTarget::VREF => {
+                    &self.channel0.dac_feedback_pin,
-                        match &self.channel0.vref_pin {
+                    stm32f4xx_hal::adc::config::SampleTime::Cycles_480
-                            Channel0VRef::Analog(vref_pin) => {
+                );
-                                for _ in (0..avg_pt).rev() {
+                let mv = self.pins_adc.sample_to_millivolts(sample);
-                                    sample += self
-                                        .pins_adc
-                                        .convert(vref_pin, stm32f4xx_hal::adc::config::SampleTime::Cycles_480)
-                                        as u32;
-                                }
-                                sample / avg_pt as u32
-                            },
-                            Channel0VRef::Disabled(_) => {2048 as u32}
-                        }
-                    }
-                    PinsAdcReadTarget::DacVfb => {
-                        for _ in (0..avg_pt).rev() {
-                            sample += self
-                                .pins_adc
-                                .convert(&self.channel0.dac_feedback_pin,stm32f4xx_hal::adc::config::SampleTime::Cycles_480)
-                                as u32;
-                        }
-                        sample / avg_pt as u32
-                    }
-                    PinsAdcReadTarget::ITec => {
-                        for _ in (0..avg_pt).rev() {
-                            sample += self
-                                .pins_adc
-                                .convert(&self.channel0.itec_pin, stm32f4xx_hal::adc::config::SampleTime::Cycles_480)
-                                as u32;
-                        }
-                        sample / avg_pt as u32
-                    }
-                    PinsAdcReadTarget::VTec => {
-                        for _ in (0..avg_pt).rev() {
-                            sample += self
-                                .pins_adc
-                                .convert(&self.channel0.tec_u_meas_pin, stm32f4xx_hal::adc::config::SampleTime::Cycles_480)
-                                as u32;
-                        }
-                        sample / avg_pt as u32
-                    }
-                };
-                let mv = self.pins_adc.sample_to_millivolts(sample as u16);
                 ElectricPotential::new::<millivolt>(mv as f64)
             }
             1 => {
-                sample = match adc_read_target {
+                let sample = self.pins_adc.convert(
-                    PinsAdcReadTarget::VREF => {
+                    &self.channel1.dac_feedback_pin,
-                        match &self.channel1.vref_pin {
+                    stm32f4xx_hal::adc::config::SampleTime::Cycles_480
-                            Channel1VRef::Analog(vref_pin) => {
+                );
-                                for _ in (0..avg_pt).rev() {
+                let mv = self.pins_adc.sample_to_millivolts(sample);
-                                    sample += self
-                                        .pins_adc
-                                        .convert(vref_pin, stm32f4xx_hal::adc::config::SampleTime::Cycles_480)
-                                        as u32;
-                                }
-                                sample / avg_pt as u32
-                            },
-                            Channel1VRef::Disabled(_) => {2048 as u32}
-                        }
-                    }
-                    PinsAdcReadTarget::DacVfb => {
-                        for _ in (0..avg_pt).rev() {
-                            sample += self
-                                .pins_adc
-                                .convert(&self.channel1.dac_feedback_pin, stm32f4xx_hal::adc::config::SampleTime::Cycles_480)
-                                as u32;
-                        }
-                        sample / avg_pt as u32
-                    }
-                    PinsAdcReadTarget::ITec => {
-                        for _ in (0..avg_pt).rev() {
-                            sample += self
-                                .pins_adc
-                                .convert(&self.channel1.itec_pin, stm32f4xx_hal::adc::config::SampleTime::Cycles_480)
-                                as u32;
-                        }
-                        sample / avg_pt as u32
-                    }
-                    PinsAdcReadTarget::VTec => {
-                        for _ in (0..avg_pt).rev() {
-                            sample += self
-                                .pins_adc
-                                .convert(&self.channel1.tec_u_meas_pin, stm32f4xx_hal::adc::config::SampleTime::Cycles_480)
-                                as u32;
-                        }
-                        sample / avg_pt as u32
-                    }
-                };
-                let mv = self.pins_adc.sample_to_millivolts(sample as u16);
                 ElectricPotential::new::<millivolt>(mv as f64)
             }
-            _ => unreachable!()
+            _ => unreachable!(),
         }
     }
 
     pub fn read_dac_feedback_until_stable(&mut self, channel: usize, tolerance: ElectricPotential) -> ElectricPotential {
-        let mut prev = self.adc_read(channel, PinsAdcReadTarget::DacVfb, 1);
+        let mut prev = self.read_dac_feedback(channel);
         loop {
-            let current = self.adc_read(channel, PinsAdcReadTarget::DacVfb, 1);
+            let current = self.read_dac_feedback(channel);
             if (current - prev).abs() < tolerance {
                 return current;
             }
@@ -280,6 +177,73 @@ impl Channels {
         }
     }
 
+    pub fn read_itec(&mut self, channel: usize) -> ElectricPotential {
+        match channel {
+            0 => {
+                let sample = self.pins_adc.convert(
+                    &self.channel0.itec_pin,
+                    stm32f4xx_hal::adc::config::SampleTime::Cycles_480
+                );
+                let mv = self.pins_adc.sample_to_millivolts(sample);
+                ElectricPotential::new::<millivolt>(mv as f64)
+            }
+            1 => {
+                let sample = self.pins_adc.convert(
+                    &self.channel1.itec_pin,
+                    stm32f4xx_hal::adc::config::SampleTime::Cycles_480
+                );
+                let mv = self.pins_adc.sample_to_millivolts(sample);
+                ElectricPotential::new::<millivolt>(mv as f64)
+            }
+            _ => unreachable!(),
+        }
+    }
+
+    /// should be 1.5V
+    pub fn read_vref(&mut self, channel: usize) -> ElectricPotential {
+        match channel {
+            0 => {
+                let sample = self.pins_adc.convert(
+                    &self.channel0.vref_pin,
+                    stm32f4xx_hal::adc::config::SampleTime::Cycles_480
+                );
+                let mv = self.pins_adc.sample_to_millivolts(sample);
+                ElectricPotential::new::<millivolt>(mv as f64)
+            }
+            1 => {
+                let sample = self.pins_adc.convert(
+                    &self.channel1.vref_pin,
+                    stm32f4xx_hal::adc::config::SampleTime::Cycles_480
+                );
+                let mv = self.pins_adc.sample_to_millivolts(sample);
+                ElectricPotential::new::<millivolt>(mv as f64)
+            }
+            _ => unreachable!(),
+        }
+    }
+
+    pub fn read_tec_u_meas(&mut self, channel: usize) -> ElectricPotential {
+        match channel {
+            0 => {
+                let sample = self.pins_adc.convert(
+                    &self.channel0.tec_u_meas_pin,
+                    stm32f4xx_hal::adc::config::SampleTime::Cycles_480
+                );
+                let mv = self.pins_adc.sample_to_millivolts(sample);
+                ElectricPotential::new::<millivolt>(mv as f64)
+            }
+            1 => {
+                let sample = self.pins_adc.convert(
+                    &self.channel1.tec_u_meas_pin,
+                    stm32f4xx_hal::adc::config::SampleTime::Cycles_480
+                );
+                let mv = self.pins_adc.sample_to_millivolts(sample);
+                ElectricPotential::new::<millivolt>(mv as f64)
+            }
+            _ => unreachable!(),
+        }
+    }
+
     /// Calibrates the DAC output to match vref of the MAX driver to reduce zero-current offset of the MAX driver output.
     ///
     /// The thermostat DAC applies a control voltage signal to the CTLI pin of MAX driver chip to control its output current.
@@ -327,7 +291,7 @@ impl Channels {
                     best_error = error;
                     start_value = prev_value;
 
-                    let vref = (value as f64 / ad5680::MAX_VALUE as f64) * DAC_OUT_V_MAX;
+                    let vref = (value as f64 / ad5680::MAX_VALUE as f64) * ElectricPotential::new::<volt>(DAC_OUT_V_MAX);
                     match channel {
                         0 => self.channel0.vref_meas = vref,
                         1 => self.channel1.vref_meas = vref,
@@ -387,32 +351,32 @@ impl Channels {
         }
     }
 
-    pub fn get_max_v(&mut self, channel: usize) -> (ElectricPotential, ElectricPotential) {
+    pub fn get_max_v(&mut self, channel: usize) -> ElectricPotential {
         let max = 4.0 * ElectricPotential::new::<volt>(3.3);
         let duty = self.get_pwm(channel, PwmPin::MaxV);
-        (duty * max, MAX_TEC_V)
+        duty * max
     }
 
     pub fn get_max_i_pos(&mut self, channel: usize) -> (ElectricCurrent, ElectricCurrent) {
         let max = ElectricCurrent::new::<ampere>(3.0);
         let duty = self.get_pwm(channel, PwmPin::MaxIPos);
-        (duty * max, MAX_TEC_I)
+        (duty * max, max)
     }
 
     pub fn get_max_i_neg(&mut self, channel: usize) -> (ElectricCurrent, ElectricCurrent) {
         let max = ElectricCurrent::new::<ampere>(3.0);
         let duty = self.get_pwm(channel, PwmPin::MaxINeg);
-        (duty * max, MAX_TEC_I)
+        (duty * max, max)
     }
 
     // Get current passing through TEC
     pub fn get_tec_i(&mut self, channel: usize) -> ElectricCurrent {
-        (self.adc_read(channel, PinsAdcReadTarget::ITec, 16) - self.adc_read(channel, PinsAdcReadTarget::VREF, 16)) / ElectricalResistance::new::<ohm>(0.4)
+        (self.read_itec(channel) - self.read_vref(channel)) / ElectricalResistance::new::<ohm>(0.4)
     }
 
     // Get voltage across TEC
     pub fn get_tec_v(&mut self, channel: usize) -> ElectricPotential {
-        (self.adc_read(channel, PinsAdcReadTarget::VTec, 16) - ElectricPotential::new::<volt>(1.5)) * 4.0
+        (self.read_tec_u_meas(channel) - ElectricPotential::new::<volt>(1.5)) * 4.0
     }
 
     fn set_pwm(&mut self, channel: usize, pin: PwmPin, duty: f64) -> f64 {
@@ -444,29 +408,29 @@ impl Channels {
 
     pub fn set_max_v(&mut self, channel: usize, max_v: ElectricPotential) -> (ElectricPotential, ElectricPotential) {
         let max = 4.0 * ElectricPotential::new::<volt>(3.3);
-        let duty = (max_v.min(MAX_TEC_V).max(ElectricPotential::zero()) / max).get::<ratio>();
+        let duty = (max_v / max).get::<ratio>();
         let duty = self.set_pwm(channel, PwmPin::MaxV, duty);
         (duty * max, max)
     }
 
     pub fn set_max_i_pos(&mut self, channel: usize, max_i_pos: ElectricCurrent) -> (ElectricCurrent, ElectricCurrent) {
         let max = ElectricCurrent::new::<ampere>(3.0);
-        let duty = (max_i_pos.min(MAX_TEC_I).max(ElectricCurrent::zero()) / max).get::<ratio>();
+        let duty = (max_i_pos / max).get::<ratio>();
         let duty = self.set_pwm(channel, PwmPin::MaxIPos, duty);
         (duty * max, max)
     }
 
     pub fn set_max_i_neg(&mut self, channel: usize, max_i_neg: ElectricCurrent) -> (ElectricCurrent, ElectricCurrent) {
         let max = ElectricCurrent::new::<ampere>(3.0);
-        let duty = (max_i_neg.min(MAX_TEC_I).max(ElectricCurrent::zero()) / max).get::<ratio>();
+        let duty = (max_i_neg / max).get::<ratio>();
         let duty = self.set_pwm(channel, PwmPin::MaxINeg, duty);
         (duty * max, max)
     }
 
     fn report(&mut self, channel: usize) -> Report {
         let i_set = self.get_i(channel);
-        let i_tec = self.adc_read(channel, PinsAdcReadTarget::ITec, 16);
+        let i_tec = if self.hwrev.major > 2 {Some(self.read_itec(channel))} else {None};
-        let tec_i = self.get_tec_i(channel);
+        let tec_i = if self.hwrev.major > 2 {Some(self.get_tec_i(channel))} else {None};
         let dac_value = self.get_dac(channel);
         let state = self.channel_state(channel);
         let pid_output = ElectricCurrent::new::<ampere>(state.pid.y1);
@@ -481,7 +445,7 @@ impl Channels {
             pid_engaged: state.pid_engaged,
             i_set,
             dac_value,
-            dac_feedback: self.adc_read(channel, PinsAdcReadTarget::DacVfb, 1),
+            dac_feedback: self.read_dac_feedback(channel),
             i_tec,
             tec_i,
             tec_u_meas: self.get_tec_v(channel),
@@ -518,8 +482,8 @@ impl Channels {
         PwmSummary {
             channel,
             center: CenterPointJson(self.channel_state(channel).center.clone()),
-            i_set: (self.get_i(channel), MAX_TEC_I).into(),
+            i_set: (self.get_i(channel), ElectricCurrent::new::<ampere>(3.0)).into(),
-            max_v: self.get_max_v(channel).into(),
+            max_v: (self.get_max_v(channel), ElectricPotential::new::<volt>(5.0)).into(),
             max_i_pos: self.get_max_i_pos(channel).into(),
             max_i_neg: self.get_max_i_neg(channel).into(),
         }
@@ -579,8 +543,8 @@ pub struct Report {
     i_set: ElectricCurrent,
     dac_value: ElectricPotential,
     dac_feedback: ElectricPotential,
-    i_tec: ElectricPotential,
+    i_tec: Option<ElectricPotential>,
-    tec_i: ElectricCurrent,
+    tec_i: Option<ElectricCurrent>,
     tec_u_meas: ElectricPotential,
     pid_output: ElectricCurrent,
 }

src/config.rs

@@ -1,4 +1,3 @@
-use num_traits::Zero;
 use serde::{Serialize, Deserialize};
 use uom::si::{
     electric_potential::volt,
@@ -19,7 +18,6 @@ pub struct ChannelConfig {
     pid: pid::Parameters,
     pid_target: f32,
     pid_engaged: bool,
-    i_set: ElectricCurrent,
     sh: steinhart_hart::Parameters,
     pwm: PwmLimits,
     /// uses variant `PostFilter::Invalid` instead of `None` to save space
@@ -35,17 +33,11 @@ impl ChannelConfig {
             .unwrap_or(PostFilter::Invalid);
 
         let state = channels.channel_state(channel);
-        let i_set = if state.pid_engaged { 
-            ElectricCurrent::zero() 
-        } else { 
-            state.i_set 
-        };
         ChannelConfig {
             center: state.center.clone(),
             pid: state.pid.parameters.clone(),
             pid_target: state.pid.target as f32,
             pid_engaged: state.pid_engaged,
-            i_set: i_set,
             sh: state.sh.clone(),
             pwm,
             adc_postfilter,
@@ -67,7 +59,6 @@ impl ChannelConfig {
             adc_postfilter => Some(adc_postfilter),
         };
         let _ = channels.adc.set_postfilter(channel as u8, adc_postfilter);
-        let _ = channels.set_i(channel, self.i_set);
     }
 }
 
@@ -80,7 +71,7 @@ struct PwmLimits {
 
 impl PwmLimits {
     pub fn new(channels: &mut Channels, channel: usize) -> Self {
-        let (max_v, _) = channels.get_max_v(channel);
+        let max_v = channels.get_max_v(channel);
         let (max_i_pos, _) = channels.get_max_i_pos(channel);
         let (max_i_neg, _) = channels.get_max_i_neg(channel);
         PwmLimits {

src/fan_ctrl.rs

@@ -11,11 +11,13 @@ use uom::si::{
 use crate::{
     hw_rev::HWSettings,
     command_handler::JsonBuffer,
-    channels::MAX_TEC_I,
 };
 
 pub type FanPin = PwmChannels<TIM8, pwm::C4>;
 
+// as stated in the schematics
+const MAX_TEC_I: f32 = 3.0;
+
 const MAX_USER_FAN_PWM: f32 = 100.0;
 const MIN_USER_FAN_PWM: f32 = 1.0;
 
@@ -54,7 +56,7 @@ impl FanCtrl {
     pub fn cycle(&mut self, abs_max_tec_i: ElectricCurrent) {
         self.abs_max_tec_i = abs_max_tec_i.get::<ampere>() as f32;
         if self.fan_auto && self.hw_settings.fan_available {
-            let scaled_current = self.abs_max_tec_i / MAX_TEC_I.get::<ampere>() as f32;
+            let scaled_current = self.abs_max_tec_i / MAX_TEC_I;
             // do not limit upper bound, as it will be limited in the set_pwm()
             let pwm = (MAX_USER_FAN_PWM * (scaled_current * (scaled_current * self.k_a + self.k_b) + self.k_c)) as u32;
             self.set_pwm(pwm);

src/main.rs

@@ -138,7 +138,7 @@ fn main() -> ! {
 
     let mut store = flash_store::store(dp.FLASH);
 
-    let mut channels = Channels::new(pins);
+    let mut channels = Channels::new(pins, &hwrev);
     for c in 0..CHANNELS {
         match store.read_value::<ChannelConfig>(CHANNEL_CONFIG_KEY[c]) {
             Ok(Some(config)) =>

src/pid.rs

@@ -54,13 +54,15 @@ impl Controller {
     //       + x0 * (kp + ki + kd)
     //       - x1 * (kp + 2kd)
     //       + x2 * kd
+    //       + kp * (u0 - u1)
     // y0  = clip(y0', ymin, ymax)
     pub fn update(&mut self, input: f64) -> f64 {
         
         let mut output: f64 = self.y1 - self.target * f64::from(self.parameters.ki)
                             + input * f64::from(self.parameters.kp + self.parameters.ki + self.parameters.kd)
                             - self.x1 * f64::from(self.parameters.kp + 2.0 * self.parameters.kd)
-                            + self.x2 * f64::from(self.parameters.kd);
+                            + self.x2 * f64::from(self.parameters.kd)
+                            + f64::from(self.parameters.kp) * (self.target - self.u1);
         if output < self.parameters.output_min.into() {
             output = self.parameters.output_min.into();
         }

src/pins.rs

@@ -66,31 +66,21 @@ pub trait ChannelPins {
     type TecUMeasPin;
 }
 
-pub enum Channel0VRef {
-    Analog(PA0<Analog>),
-    Disabled(PA0<Input<Floating>>),
-}
-
 impl ChannelPins for Channel0 {
     type DacSpi = Dac0Spi;
     type DacSync = PE4<Output<PushPull>>;
     type Shdn = PE10<Output<PushPull>>;
-    type VRefPin = Channel0VRef;
+    type VRefPin = PA0<Analog>;
     type ItecPin = PA6<Analog>;
     type DacFeedbackPin = PA4<Analog>;
     type TecUMeasPin = PC2<Analog>;
 }
 
-pub enum Channel1VRef {
-    Analog(PA3<Analog>),
-    Disabled(PA3<Input<Floating>>),
-}
-
 impl ChannelPins for Channel1 {
     type DacSpi = Dac1Spi;
     type DacSync = PF6<Output<PushPull>>;
     type Shdn = PE15<Output<PushPull>>;
-    type VRefPin = Channel1VRef;
+    type VRefPin = PA3<Analog>;
     type ItecPin = PB0<Analog>;
     type DacFeedbackPin = PA5<Analog>;
     type TecUMeasPin = PC3<Analog>;
@@ -160,17 +150,13 @@ impl Pins {
             gpioe.pe13, gpioe.pe14
         );
 
-        let hwrev = HWRev::detect_hw_rev(&HWRevPins {hwrev0: gpiod.pd0, hwrev1: gpiod.pd1,
-            hwrev2: gpiod.pd2, hwrev3: gpiod.pd3});
-        let hw_settings = hwrev.settings();
-
         let (dac0_spi, dac0_sync) = Self::setup_dac0(
             clocks, spi4,
             gpioe.pe2, gpioe.pe4, gpioe.pe6
         );
         let mut shdn0 = gpioe.pe10.into_push_pull_output();
         let _ = shdn0.set_low();
-        let vref0_pin = if hwrev.major > 2 {Channel0VRef::Analog(gpioa.pa0.into_analog())} else {Channel0VRef::Disabled(gpioa.pa0)};
+        let vref0_pin = gpioa.pa0.into_analog();
         let itec0_pin = gpioa.pa6.into_analog();
         let dac_feedback0_pin = gpioa.pa4.into_analog();
         let tec_u_meas0_pin = gpioc.pc2.into_analog();
@@ -190,7 +176,7 @@ impl Pins {
         );
         let mut shdn1 = gpioe.pe15.into_push_pull_output();
         let _ = shdn1.set_low();
-        let vref1_pin = if hwrev.major > 2 {Channel1VRef::Analog(gpioa.pa3.into_analog())} else {Channel1VRef::Disabled(gpioa.pa3)};
+        let vref1_pin = gpioa.pa3.into_analog();
         let itec1_pin = gpiob.pb0.into_analog();
         let dac_feedback1_pin = gpioa.pa5.into_analog();
         let tec_u_meas1_pin = gpioc.pc3.into_analog();
@@ -212,6 +198,10 @@ impl Pins {
             channel1,
         };
 
+        let hwrev = HWRev::detect_hw_rev(&HWRevPins {hwrev0: gpiod.pd0, hwrev1: gpiod.pd1,
+            hwrev2: gpiod.pd2, hwrev3: gpiod.pd3});
+        let hw_settings = hwrev.settings();
+
         let leds = Leds::new(gpiod.pd9, gpiod.pd10.into_push_pull_output(), gpiod.pd11.into_push_pull_output());
 
         let eeprom_scl = gpiob.pb8.into_alternate().set_open_drain();