ethernet: minimal impl for urukul as scpi device

examples/ethernet.rs

@@ -24,9 +24,12 @@ extern crate smoltcp;
 extern crate stm32h7_ethernet as ethernet;
 
 use stm32h7xx_hal::gpio::Speed;
-use stm32h7xx_hal::hal::digital::v2::OutputPin;
+use stm32h7xx_hal::hal::digital::v2::{
+    OutputPin,
+    InputPin,
+};
 use stm32h7xx_hal::rcc::CoreClocks;
-use stm32h7xx_hal::{pac, prelude::*, stm32, stm32::interrupt};
+use stm32h7xx_hal::{pac, prelude::*, spi, stm32, stm32::interrupt};
 use Speed::*;
 
 use libm::round;
@@ -55,7 +58,24 @@ use smoltcp::socket::SocketSet;
 use smoltcp::socket::{SocketHandle, TcpSocket, TcpSocketBuffer};
 use smoltcp::time::{Duration, Instant};
 
-use firmware::scpi::{MyDevice, TREE};
+use firmware;
+use firmware::{
+	attenuator::Attenuator,
+	config_register::{
+		ConfigRegister,
+		CFGMask,
+		StatusMask,
+	},
+	dds::{
+		DDS,
+		DDSCFRMask,
+	},
+	cpld::{
+		CPLD,
+    },
+    scpi::TREE,
+    Urukul,
+};
 use scpi::prelude::*;
 
 /// Configure SYSTICK for 1ms timebase
@@ -111,6 +131,7 @@ fn main() -> ! {
         .sys_ck(200.mhz())
         .hclk(200.mhz())
         .pll1_r_ck(100.mhz()) // for TRACECK
+        .pll1_q_ck(48.mhz())
         .freeze(vos, &dp.SYSCFG);
 
     // Get the delay provider.
@@ -127,14 +148,65 @@ fn main() -> ! {
     let gpioa = dp.GPIOA.split(ccdr.peripheral.GPIOA);
     let gpiob = dp.GPIOB.split(ccdr.peripheral.GPIOB);
     let gpioc = dp.GPIOC.split(ccdr.peripheral.GPIOC);
-    let gpioe = dp.GPIOE.split(ccdr.peripheral.GPIOE);
+	let gpiod = dp.GPIOD.split(ccdr.peripheral.GPIOD);
+	let gpioe = dp.GPIOE.split(ccdr.peripheral.GPIOE);
+	let gpiof = dp.GPIOF.split(ccdr.peripheral.GPIOF);
     let gpiog = dp.GPIOG.split(ccdr.peripheral.GPIOG);
-    let mut link_led = gpiob.pb0.into_push_pull_output(); // LED1, green
-    let mut status_led = gpioe.pe1.into_push_pull_output(); // LD2, yellow
-    let mut listen_led = gpiob.pb14.into_push_pull_output(); // LD3, red
-    link_led.set_low().ok();
-    status_led.set_low().ok();
-    listen_led.set_low().ok();
+    // let mut link_led = gpiob.pb0.into_push_pull_output(); // LED1, green
+    // let mut status_led = gpioe.pe1.into_push_pull_output(); // LD2, yellow
+    // let mut listen_led = gpiob.pb14.into_push_pull_output(); // LD3, red
+    // link_led.set_low().ok();
+    // status_led.set_low().ok();
+    // listen_led.set_low().ok();
+
+	// Setup CDONE for checking
+	let fpga_cdone = gpiod.pd15.into_pull_up_input();
+
+	match fpga_cdone.is_high() {
+		Ok(true)	=> hprintln!("FPGA is ready."),
+		Ok(_)		=> hprintln!("FPGA is in reset state."),
+		Err(_)		=> hprintln!("Error: Cannot read C_DONE"),
+    }.unwrap();
+    
+    // Setup Urukul
+	/*
+	 *	Using SPI1, AF5
+	 *  SCLK -> PA5
+	 *	MOSI -> PB5
+	 *	MISO -> PA6
+	 *	CS -> 0: PB12, 1: PA15, 2: PC7
+	 */
+
+    let sclk = gpioa.pa5.into_alternate_af5();
+    let mosi = gpiob.pb5.into_alternate_af5();
+    let miso = gpioa.pa6.into_alternate_af5();
+
+
+    let (cs0, cs1, cs2) = (
+        gpiob.pb12.into_push_pull_output(),
+        gpioa.pa15.into_push_pull_output(),
+        gpioc.pc7.into_push_pull_output(),
+    );
+
+    /*
+     *	I/O_Update -> PB15
+     */
+    let io_update = gpiob.pb15.into_push_pull_output();
+
+    let spi = dp.SPI1.spi(
+        (sclk, miso, mosi),
+        spi::MODE_0,
+        3.mhz(),
+        ccdr.peripheral.SPI1,
+        &ccdr.clocks,
+    );
+
+    let switch = CPLD::new(spi, (cs0, cs1, cs2), io_update);
+    let parts = switch.split();
+    let mut urukul = Urukul::new(
+        parts.spi1, parts.spi2, parts.spi3, parts.spi4, parts.spi5, parts.spi6, parts.spi7,
+        [25_000_000, 25_000_000, 25_000_000, 25_000_000]
+    );
 
     // Setup ethernet pins
     setup_ethernet_pins(
@@ -192,18 +264,17 @@ fn main() -> ! {
             .finalize();
 
     // SCPI configs
-    let mut my_device = MyDevice {};
+    // Device was declared in prior
 
     let mut errors = ArrayErrorQueue::<[Error; 10]>::new();
-    let mut context = Context::new(&mut my_device, &mut errors, TREE);
+    let mut context = Context::new(&mut urukul, &mut errors, TREE);
 
     //Response bytebuffer
     let mut buf = ArrayVecFormatter::<[u8; 256]>::new();
 
     // SCPI configs END
 
-    // TODO: Need Iinitialize TCP socket storage?
-    // Yes cannot into vectors
+    // TCP socket buffers
     let mut rx_storage = [0; BUFFER_SIZE];
     let mut tx_storage = [0; BUFFER_SIZE];
 
@@ -242,11 +313,9 @@ fn main() -> ! {
         match iface.poll(&mut sockets, Instant::from_millis(_time as i64)) {
             Ok(_) => {
                 eth_up = true;
-                link_led.set_high().unwrap();
             },
             Err(e) => {
                 eth_up = false;
-                link_led.set_low().unwrap();
             },
         };
 
@@ -258,16 +327,6 @@ fn main() -> ! {
                 socket.set_timeout(Some(Duration::from_millis(5000)));
             }
 
-            match socket.is_listening() {
-                false => listen_led.set_low().unwrap(),
-                _ => listen_led.set_high().unwrap(),
-            };
-
-            match socket.is_active() {
-                true => status_led.set_high().unwrap(),
-                _ => status_led.set_low().unwrap(),
-            };
-
             if socket.can_recv() && receive_and_not_send {
                 let data = socket.recv(|buffer| {
                     (buffer.len(), buffer)
@@ -293,11 +352,7 @@ fn main() -> ! {
 				socket.set_timeout(Some(Duration::from_millis(1000000)));
 		    }
 
-
 		    if socket.can_recv() {
-				// hprintln!("{:?}", socket.recv(|buffer| {
-				//     (buffer.len(), str::from_utf8(buffer).unwrap())
-                // })).unwrap();
                 let result = context.run(socket.recv(|buffer| {
                     (buffer.len(), buffer)
                 }).unwrap(), &mut buf);
@@ -305,7 +360,6 @@ fn main() -> ! {
                     writeln!(socket, "{}", str::from_utf8(err.get_message()).unwrap());
                 } else {
                     write!(socket, "{}", str::from_utf8(buf.as_slice()).unwrap());
-                    //break;
                 }
 		    }
 		}

src/lib.rs

@@ -8,7 +8,6 @@ use core::{
 	cell,
 	marker::PhantomData,
 };
-
 use cortex_m;
 use cortex_m_semihosting::hprintln;
 

src/main.rs

@@ -83,7 +83,7 @@ fn main() -> ! {
 	);
 
 	/*
-	 *	I/O_Update -> PB13
+	 *	I/O_Update -> PB15
 	 */
 	let io_update = gpiob.pb15.into_push_pull_output();
 

src/scpi.rs

@@ -28,7 +28,9 @@ use scpi::{
     scpi_tree,
 };
 
-pub struct MyDevice;
+use crate::Urukul;
+
+// pub struct MyDevice;
 
 pub struct HelloWorldCommand {}
 impl Command for HelloWorldCommand {
@@ -44,7 +46,11 @@ impl Command for HelloWorldCommand {
     }
 }
 
-impl Device for MyDevice {
+/*
+ *  Implement "Device" trait from SCPI
+ *  TODO: Implement mandatory commands
+ */
+ impl<SPI> Device for Urukul<SPI> {
     fn cls(&mut self) -> Result<()> {
         Ok(())
     }