README.md

@@ -24,7 +24,7 @@ The following configuration keys are available:
 - ``ip``: IPv4 address.
 - ``ip6``: IPv6 address.
 - ``startup``: startup kernel in ELF format (as produced by ``artiq_compile``).
-- ``rtioclk``: source of RTIO clock; valid values are ``external`` and ``internal``.
+- ``rtio_clock``: source of RTIO clock; valid values are ``ext0_bypass`` and ``int_125``.
 - ``boot``: SD card "boot.bin" file, for replacing the boot firmware/gateware. Write only.
 
 Configurations can be read/written/removed via ``artiq_coremgmt``. Config erase is

src/gateware/kasli_soc.py

@@ -113,8 +113,8 @@ class GenericStandalone(SoCCore):
         platform.add_platform_command("create_clock -name clk_fpga_0 -period 8 [get_pins \"PS7/FCLKCLK[0]\"]")
         platform.add_platform_command("set_input_jitter clk_fpga_0 0.24")
 
-        self.rustc_cfg["HAS_SI5324"] = None
-        self.rustc_cfg["SI5324_SOFT_RESET"] = None
+        self.rustc_cfg["has_si5324"] = None
+        self.rustc_cfg["si5324_soft_reset"] = None
 
         self.crg = self.ps7 # HACK for eem_7series to find the clock
         self.submodules.rtio_crg = RTIOCRG(self.platform)
@@ -393,6 +393,9 @@ class GenericSatellite(SoCCore):
         self.add_memory_group("drtioaux_mem", drtioaux_memory_group)
         self.add_csr_group("drtiorep", drtiorep_csr_group)
 
+        self.rustc_cfg["has_si5324"] = None
+        self.rustc_cfg["si5324_soft_reset"] = None
+
         if self.acpki:
             self.rustc_cfg["ki_impl"] = "acp"
             self.submodules.rtio = acpki.KernelInitiator(self.rtio_tsc,

src/runtime/src/main.rs

@@ -18,12 +18,9 @@ use libasync::{task, block_async};
 use libsupport_zynq::ram;
 use nb;
 use void::Void;
-use embedded_hal::blocking::delay::DelayMs;
 use libconfig::Config;
 use libcortex_a9::l2c::enable_l2_cache;
 use libboard_artiq::{logger, identifier_read, init_gateware, pl};
-#[cfg(has_si5324)]
-use libboard_artiq::si5324;
 
 mod proto_async;
 mod comms;
@@ -35,6 +32,7 @@ mod rtio;
 #[path = "rtio_acp.rs"]
 mod rtio;
 mod rtio_mgt;
+mod rtio_clocking;
 mod kernel;
 mod moninj;
 mod eh_artiq;
@@ -44,65 +42,6 @@ mod analyzer;
 mod irq;
 mod i2c;
 
-fn init_rtio(timer: &mut GlobalTimer, _cfg: &Config) {
-    #[cfg(has_rtio_crg_clock_sel)]
-    let clock_sel =
-        if let Ok(rtioclk) = _cfg.read_str("rtioclk") {
-            match rtioclk.as_ref() {
-                "internal" => {
-                    info!("using internal RTIO clock");
-                    0
-                },
-                "external" => {
-                    info!("using external RTIO clock");
-                    1
-                },
-                other => {
-                    warn!("RTIO clock specification '{}' not recognized", other);
-                    info!("using internal RTIO clock");
-                    0
-                },
-            }
-        } else {
-            info!("using internal RTIO clock (default)");
-            0
-        };
-
-    loop {
-        unsafe {
-            pl::csr::rtio_crg::pll_reset_write(1);
-            #[cfg(has_rtio_crg_clock_sel)]
-            pl::csr::rtio_crg::clock_sel_write(clock_sel);
-            pl::csr::rtio_crg::pll_reset_write(0);
-        }
-        timer.delay_ms(1);
-        let locked = unsafe { pl::csr::rtio_crg::pll_locked_read() != 0 };
-        if locked {
-            info!("RTIO PLL locked");
-            break;
-        } else {
-            warn!("RTIO PLL failed to lock, retrying...");
-            timer.delay_ms(500);
-        }
-    }
-
-    unsafe {
-        pl::csr::rtio_core::reset_phy_write(1);
-    }
-}
-
-#[cfg(has_drtio)]
-fn init_drtio(timer: &mut GlobalTimer)
-{
-    unsafe {
-        pl::csr::drtio_transceiver::stable_clkin_write(1);
-    }
-    timer.delay_ms(2); // wait for CPLL/QPLL lock
-    unsafe {
-        pl::csr::drtio_transceiver::txenable_write(0xffffffffu32 as _);
-    }
-}
-
 
 fn wait_for_async_rtio_error() -> nb::Result<(), Void> {
     unsafe {
@@ -136,19 +75,7 @@ async fn report_async_rtio_errors() {
     }
 }
 
-#[cfg(has_si5324)]
-// 125MHz output, from crystal, 7 Hz
-const SI5324_SETTINGS: si5324::FrequencySettings
-    = si5324::FrequencySettings {
-    n1_hs  : 10,
-    nc1_ls : 4,
-    n2_hs  : 10,
-    n2_ls  : 19972,
-    n31    : 4565,
-    n32    : 4565,
-    bwsel  : 4,
-    crystal_ref: true
-};
+
 
 static mut LOG_BUFFER: [u8; 1<<17] = [0; 1<<17];
 
@@ -173,9 +100,6 @@ pub fn main_core0() {
     info!("detected gateware: {}", identifier_read(&mut [0; 64]));
 
     i2c::init();
-    #[cfg(has_si5324)]
-    si5324::setup(unsafe { (&mut i2c::I2C_BUS).as_mut().unwrap() },
-        &SI5324_SETTINGS, si5324::Input::Ckin2, &mut timer).expect("cannot initialize Si5324");
 
     let cfg = match Config::new() {
         Ok(cfg) => cfg,
@@ -185,10 +109,8 @@ pub fn main_core0() {
         }
     };
 
-    #[cfg(has_drtio)]
-    init_drtio(&mut timer);
+    rtio_clocking::init(&mut timer, &cfg);
 
-    init_rtio(&mut timer, &cfg);
     task::spawn(report_async_rtio_errors());
 
     comms::main(timer, cfg);

src/runtime/src/rtio_clocking.rs

@@ -0,0 +1,224 @@
+use log::{info, warn};
+use libboard_zynq::timer::GlobalTimer;
+use embedded_hal::blocking::delay::DelayMs;
+use libconfig::Config;
+use libboard_artiq::pl;
+#[cfg(has_si5324)]
+use libboard_zynq::i2c::I2c;
+#[cfg(has_si5324)]
+use crate::i2c;
+#[cfg(has_si5324)]
+use libboard_artiq::si5324;
+
+#[derive(Debug, PartialEq, Copy, Clone)]
+#[allow(non_camel_case_types)]
+pub enum RtioClock {
+    Default,
+    Int_125,
+    Int_100,
+    Int_150,
+    Ext0_Bypass,
+    Ext0_Synth0_10to125,
+    Ext0_Synth0_100to125,
+    Ext0_Synth0_125to125,
+}
+
+fn get_rtio_clock_cfg(cfg: &Config) -> RtioClock {
+    let mut res = RtioClock::Default;
+    if let Ok(clk) = cfg.read_str("rtio_clock") {
+        res = match clk.as_ref() {
+            "int_125" => RtioClock::Int_125,
+            "int_100" => RtioClock::Int_100,
+            "int_150" => RtioClock::Int_150,
+            "ext0_bypass" => RtioClock::Ext0_Bypass,
+            "ext0_bypass_125" => RtioClock::Ext0_Bypass,
+            "ext0_bypass_100" => RtioClock::Ext0_Bypass,
+            "ext0_synth0_10to125" => RtioClock::Ext0_Synth0_10to125,
+            "ext0_synth0_100to125" => RtioClock::Ext0_Synth0_100to125,
+            "ext0_synth0_125to125" => RtioClock::Ext0_Synth0_125to125,
+            _ => { 
+                warn!("Unrecognised rtio_clock setting. Falling back to default.");
+                RtioClock::Default 
+            }
+        };
+    }
+    else {
+        warn!("error reading configuration. Falling back to default.");
+    }
+    if res == RtioClock::Default {
+        warn!("Using default configuration - internal 125MHz RTIO clock.");
+        return RtioClock::Int_125;
+    }
+    res
+}
+
+
+fn init_rtio(timer: &mut GlobalTimer, _clk: RtioClock) {
+    #[cfg(has_rtio_crg_clock_sel)]
+    let clock_sel = match _clk {
+        RtioClock::Ext0_Bypass => { 
+            info!("Using bypassed external clock");
+            1
+        },
+        RtioClock::Int_125 => {
+            info!("Using internal RTIO clock");
+            0
+        },
+        _ => {
+            warn!("rtio_clock setting '{:?}' is not supported. Using default internal RTIO clock instead", _clk);
+            0
+        }
+    };
+
+    loop {
+        unsafe {
+            pl::csr::rtio_crg::pll_reset_write(1);
+            #[cfg(has_rtio_crg_clock_sel)]
+            pl::csr::rtio_crg::clock_sel_write(clock_sel);
+            pl::csr::rtio_crg::pll_reset_write(0);
+        }
+        timer.delay_ms(1);
+        let locked = unsafe { pl::csr::rtio_crg::pll_locked_read() != 0 };
+        if locked {
+            info!("RTIO PLL locked");
+            break;
+        } else {
+            warn!("RTIO PLL failed to lock, retrying...");
+            timer.delay_ms(500);
+        }
+    }
+
+    unsafe {
+        pl::csr::rtio_core::reset_phy_write(1);
+    }
+}
+
+#[cfg(has_drtio)]
+fn init_drtio(timer: &mut GlobalTimer)
+{
+    unsafe {
+        pl::csr::drtio_transceiver::stable_clkin_write(1);
+    }
+    timer.delay_ms(2); // wait for CPLL/QPLL lock
+    unsafe {
+        pl::csr::drtio_transceiver::txenable_write(0xffffffffu32 as _);
+    }
+}
+
+#[cfg(has_si5324)]
+fn setup_si5324(i2c: &mut I2c, timer: &mut GlobalTimer, clk: RtioClock) {
+    let si5324_settings = match clk {
+        RtioClock::Ext0_Synth0_10to125 => { // 125 MHz output from 10 MHz CLKINx reference, 504 Hz BW
+            info!("using 10MHz reference to make 125MHz RTIO clock with PLL");
+            si5324::FrequencySettings {
+                n1_hs  : 10,
+                nc1_ls : 4,
+                n2_hs  : 10,
+                n2_ls  : 300,
+                n31    : 6,
+                n32    : 6,
+                bwsel  : 4,
+                crystal_ref: false
+            }
+        },
+        RtioClock::Ext0_Synth0_100to125 => { // 125MHz output, from 100MHz CLKINx reference, 586 Hz loop bandwidth
+            info!("using 10MHz reference to make 125MHz RTIO clock with PLL");
+            si5324::FrequencySettings {
+                n1_hs  : 10,
+                nc1_ls : 4,
+                n2_hs  : 10,
+                n2_ls  : 260,
+                n31    : 52,
+                n32    : 52,
+                bwsel  : 4,
+                crystal_ref: false
+            }
+        },
+        RtioClock::Ext0_Synth0_125to125 => { // 125MHz output, from 125MHz CLKINx reference, 606 Hz loop bandwidth
+            info!("using 10MHz reference to make 125MHz RTIO clock with PLL");
+            si5324::FrequencySettings {
+                n1_hs  : 5,
+                nc1_ls : 8,
+                n2_hs  : 7,
+                n2_ls  : 360,
+                n31    : 63,
+                n32    : 63,
+                bwsel  : 4,
+                crystal_ref: false
+            }
+        },
+        RtioClock::Int_150 => { // 150MHz output, from crystal
+            info!("using internal 150MHz RTIO clock");
+            si5324::FrequencySettings {
+                n1_hs  : 9,
+                nc1_ls : 4,
+                n2_hs  : 10,
+                n2_ls  : 33732,
+                n31    : 7139,
+                n32    : 7139,
+                bwsel  : 3,
+                crystal_ref: true
+            }
+        },
+        RtioClock::Int_100 => { // 100MHz output, from crystal.
+            info!("using internal 100MHz RTIO clock");
+            si5324::FrequencySettings {
+                n1_hs  : 9,
+                nc1_ls : 6,
+                n2_hs  : 10,
+                n2_ls  : 33732,
+                n31    : 7139,
+                n32    : 7139,
+                bwsel  : 3,
+                crystal_ref: true
+            }
+        },
+        RtioClock::Int_125 => { // 125MHz output, from crystal, 7 Hz
+            info!("using internal 125MHz RTIO clock");
+            si5324::FrequencySettings {
+                n1_hs  : 10,
+                nc1_ls : 4,
+                n2_hs  : 10,
+                n2_ls  : 19972,
+                n31    : 4565,
+                n32    : 4565,
+                bwsel  : 4,
+                crystal_ref: true
+            }
+        }
+        _ => { // same setting  as Int_125, but fallback to default
+            warn!("rtio_clock setting '{:?}' is unsupported. Falling back to default internal 125MHz RTIO clock.", clk);
+            si5324::FrequencySettings {
+                n1_hs  : 10,
+                nc1_ls : 4,
+                n2_hs  : 10,
+                n2_ls  : 19972,
+                n31    : 4565,
+                n32    : 4565,
+                bwsel  : 4,
+                crystal_ref: true
+            }
+        }
+    };
+    let si5324_ref_input = si5324::Input::Ckin2;
+    si5324::setup(i2c, &si5324_settings, si5324_ref_input, timer).expect("cannot initialize Si5324");
+}
+
+pub fn init(timer: &mut GlobalTimer, cfg: &Config) {
+
+    let clk = get_rtio_clock_cfg(cfg);
+    #[cfg(has_si5324)]
+    {
+        let i2c = unsafe { (&mut i2c::I2C_BUS).as_mut().unwrap() };
+        let si5324_ext_input = si5324::Input::Ckin2;
+        match clk {
+            RtioClock::Ext0_Bypass => si5324::bypass(i2c, si5324_ext_input, timer).expect("cannot bypass Si5324"),
+            _ => setup_si5324(i2c, timer, clk),
+        }
+    }
+    #[cfg(has_drtio)]
+    init_drtio(timer);
+
+    init_rtio(timer, clk);
+
+}