forked from M-Labs/artiq
335 lines
12 KiB
Python
335 lines
12 KiB
Python
from itertools import product
|
|
|
|
from migen import *
|
|
from misoc.interconnect import wishbone
|
|
from misoc.cores.spi import SPIMachine
|
|
|
|
|
|
class SPIMaster(Module):
|
|
"""SPI Master.
|
|
|
|
Notes:
|
|
* M = 32 is the data width (width of the data register,
|
|
maximum write bits, maximum read bits)
|
|
* Every transfer consists of a write_length 0-M bit write followed
|
|
by a read_length 0-M bit read.
|
|
* cs_n is asserted at the beginning and deasserted at the end of the
|
|
transfer if there is no other transfer pending.
|
|
* cs_n handling is agnostic to whether it is one-hot or decoded
|
|
somewhere downstream. If it is decoded, "cs_n all deasserted"
|
|
should be handled accordingly (no slave selected).
|
|
If it is one-hot, asserting multiple slaves should only be attempted
|
|
if miso is either not connected between slaves, or open collector,
|
|
or correctly multiplexed externally.
|
|
* If config.cs_polarity == 0 (cs active low, the default),
|
|
"cs_n all deasserted" means "all cs_n bits high".
|
|
* cs is not mandatory in pads. Framing and chip selection can also
|
|
be handled independently through other means.
|
|
* If there is a miso wire in pads, the input and output can be done
|
|
with two signals (a.k.a. 4-wire SPI), else mosi must be used for
|
|
both output and input (a.k.a. 3-wire SPI) and config.half_duplex
|
|
must to be set when reading data is desired.
|
|
* For 4-wire SPI only the sum of read_length and write_length matters.
|
|
The behavior is the same no matter how the total transfer length is
|
|
divided between the two. For 3-wire SPI, the direction of mosi/miso
|
|
is switched from output to input after write_len cycles, at the
|
|
"shift_out" clk edge corresponding to bit write_length + 1 of the
|
|
transfer.
|
|
* The first bit output on mosi is always the MSB/LSB (depending on
|
|
config.lsb_first) of the data register, independent of
|
|
xfer.write_len. The last bit input from miso always ends up in
|
|
the LSB/MSB (respectively) of the data register, independent of
|
|
read_len.
|
|
* Data output on mosi in 4-wire SPI during the read cycles is what
|
|
is found in the data register at the time.
|
|
Data in the data register outside the least/most (depending
|
|
on config.lsb_first) significant read_length bits is what is
|
|
seen on miso during the write cycles.
|
|
* The SPI data register is double-buffered: Once a transfer has
|
|
started, new write data can be written, queuing a new transfer.
|
|
Transfers submitted this way are chained and executed without
|
|
deasserting cs. Once a transfer completes, the previous transfer's
|
|
read data is available in the data register.
|
|
* Writes to the config register take effect immediately. Writes to xfer
|
|
and data are synchronized to the start of a transfer.
|
|
* A wishbone data register write is ack-ed when the transfer has
|
|
been written to the intermediate buffer. It will be started when
|
|
there are no other transactions being executed, either starting
|
|
a new SPI transfer of chained to an in-flight transfer.
|
|
Writes take two cycles unless the write is to the data register
|
|
and another chained transfer is pending and the transfer being
|
|
executed is not complete. Reads always finish in two cycles.
|
|
|
|
Transaction Sequence:
|
|
* If desired, write the config register to set up the core.
|
|
* If desired, write the xfer register to change lengths and cs_n.
|
|
* Write the data register (also for zero-length writes),
|
|
writing triggers the transfer and when the transfer is accepted to
|
|
the inermediate buffer, the write is ack-ed.
|
|
* If desired, read the data register corresponding to the last
|
|
completed transfer.
|
|
* If desired, change xfer register for the next transfer.
|
|
* If desired, write data queuing the next (possibly chained) transfer.
|
|
|
|
Register address and bit map:
|
|
|
|
config (address 2):
|
|
1 offline: all pins high-z (reset=1)
|
|
1 active: cs/transfer active (read-only)
|
|
1 pending: transfer pending in intermediate buffer (read-only)
|
|
1 cs_polarity: active level of chip select (reset=0)
|
|
1 clk_polarity: idle level of clk (reset=0)
|
|
1 clk_phase: first edge after cs assertion to sample data on (reset=0)
|
|
(clk_polarity, clk_phase) == (CPOL, CPHA) in Freescale language.
|
|
(0, 0): idle low, output on falling, input on rising
|
|
(0, 1): idle low, output on rising, input on falling
|
|
(1, 0): idle high, output on rising, input on falling
|
|
(1, 1): idle high, output on falling, input on rising
|
|
There is never a clk edge during a cs edge.
|
|
1 lsb_first: LSB is the first bit on the wire (reset=0)
|
|
1 half_duplex: 3-wire SPI, in/out on mosi (reset=0)
|
|
8 undefined
|
|
8 div_write: counter load value to divide this module's clock
|
|
to generate the SPI write clk (reset=0)
|
|
f_clk/f_spi_write == div_write + 2
|
|
8 div_read: ditto for the read clock
|
|
|
|
xfer (address 1):
|
|
16 cs: active high bit mask of chip selects to assert (reset=0)
|
|
6 write_len: 0-M bits (reset=0)
|
|
2 undefined
|
|
6 read_len: 0-M bits (reset=0)
|
|
2 undefined
|
|
|
|
data (address 0):
|
|
M write/read data (reset=0)
|
|
"""
|
|
def __init__(self, pads, bus=None):
|
|
if bus is None:
|
|
bus = wishbone.Interface(data_width=32)
|
|
self.bus = bus
|
|
|
|
###
|
|
|
|
# Wishbone
|
|
config = Record([
|
|
("offline", 1),
|
|
("active", 1),
|
|
("pending", 1),
|
|
("cs_polarity", 1),
|
|
("clk_polarity", 1),
|
|
("clk_phase", 1),
|
|
("lsb_first", 1),
|
|
("half_duplex", 1),
|
|
("padding", 8),
|
|
("div_write", 8),
|
|
("div_read", 8),
|
|
])
|
|
config.offline.reset = 1
|
|
assert len(config) <= len(bus.dat_w)
|
|
|
|
xfer = Record([
|
|
("cs", 16),
|
|
("write_length", 6),
|
|
("padding0", 2),
|
|
("read_length", 6),
|
|
("padding1", 2),
|
|
])
|
|
assert len(xfer) <= len(bus.dat_w)
|
|
|
|
self.submodules.spi = spi = SPIMachine(
|
|
data_width=len(bus.dat_w),
|
|
clock_width=len(config.div_read),
|
|
bits_width=len(xfer.read_length))
|
|
|
|
pending = Signal()
|
|
cs = Signal.like(xfer.cs)
|
|
data_read = Signal.like(spi.reg.data)
|
|
data_write = Signal.like(spi.reg.data)
|
|
|
|
self.comb += [
|
|
spi.start.eq(pending & (~spi.cs | spi.done)),
|
|
spi.clk_phase.eq(config.clk_phase),
|
|
spi.reg.lsb.eq(config.lsb_first),
|
|
spi.div_write.eq(config.div_write),
|
|
spi.div_read.eq(config.div_read),
|
|
]
|
|
self.sync += [
|
|
If(spi.done,
|
|
data_read.eq(spi.reg.data),
|
|
),
|
|
If(spi.start,
|
|
cs.eq(xfer.cs),
|
|
spi.bits.n_write.eq(xfer.write_length),
|
|
spi.bits.n_read.eq(xfer.read_length),
|
|
spi.reg.data.eq(data_write),
|
|
pending.eq(0),
|
|
),
|
|
# wb.ack a transaction if any of the following:
|
|
# a) reading,
|
|
# b) writing to non-data register
|
|
# c) writing to data register and no pending transfer
|
|
# d) writing to data register and pending and swapping buffers
|
|
bus.ack.eq(bus.cyc & bus.stb &
|
|
(~bus.we | (bus.adr != 0) | ~pending | spi.done)),
|
|
If(bus.cyc & bus.stb,
|
|
bus.dat_r.eq(
|
|
Array([data_read, xfer.raw_bits(), config.raw_bits()
|
|
])[bus.adr]),
|
|
),
|
|
If(bus.ack,
|
|
bus.ack.eq(0),
|
|
If(bus.we,
|
|
Array([data_write, xfer.raw_bits(), config.raw_bits()
|
|
])[bus.adr].eq(bus.dat_w),
|
|
If(bus.adr == 0, # data register
|
|
pending.eq(1),
|
|
),
|
|
),
|
|
),
|
|
config.active.eq(spi.cs),
|
|
config.pending.eq(pending),
|
|
]
|
|
|
|
# I/O
|
|
if hasattr(pads, "cs_n"):
|
|
cs_n_t = TSTriple(len(pads.cs_n))
|
|
self.specials += cs_n_t.get_tristate(pads.cs_n)
|
|
self.comb += [
|
|
cs_n_t.oe.eq(~config.offline),
|
|
cs_n_t.o.eq((cs & Replicate(spi.cs, len(cs))) ^
|
|
Replicate(~config.cs_polarity, len(cs))),
|
|
]
|
|
|
|
clk_t = TSTriple()
|
|
self.specials += clk_t.get_tristate(pads.clk)
|
|
self.comb += [
|
|
clk_t.oe.eq(~config.offline),
|
|
clk_t.o.eq((spi.cg.clk & spi.cs) ^ config.clk_polarity),
|
|
]
|
|
|
|
mosi_t = TSTriple()
|
|
self.specials += mosi_t.get_tristate(pads.mosi)
|
|
self.comb += [
|
|
mosi_t.oe.eq(~config.offline & spi.cs &
|
|
(spi.oe | ~config.half_duplex)),
|
|
mosi_t.o.eq(spi.reg.o),
|
|
spi.reg.i.eq(Mux(config.half_duplex, mosi_t.i,
|
|
getattr(pads, "miso", mosi_t.i))),
|
|
]
|
|
|
|
|
|
SPI_DATA_ADDR, SPI_XFER_ADDR, SPI_CONFIG_ADDR = range(3)
|
|
(
|
|
SPI_OFFLINE,
|
|
SPI_ACTIVE,
|
|
SPI_PENDING,
|
|
SPI_CS_POLARITY,
|
|
SPI_CLK_POLARITY,
|
|
SPI_CLK_PHASE,
|
|
SPI_LSB_FIRST,
|
|
SPI_HALF_DUPLEX,
|
|
) = (1 << i for i in range(8))
|
|
|
|
|
|
def SPI_DIV_WRITE(i):
|
|
return i << 16
|
|
|
|
|
|
def SPI_DIV_READ(i):
|
|
return i << 24
|
|
|
|
|
|
def SPI_CS(i):
|
|
return i << 0
|
|
|
|
|
|
def SPI_WRITE_LENGTH(i):
|
|
return i << 16
|
|
|
|
|
|
def SPI_READ_LENGTH(i):
|
|
return i << 24
|
|
|
|
|
|
def _test_xfer(bus, cs, wlen, rlen, wdata):
|
|
yield from bus.write(SPI_XFER_ADDR, SPI_CS(cs) |
|
|
SPI_WRITE_LENGTH(wlen) | SPI_READ_LENGTH(rlen))
|
|
yield from bus.write(SPI_DATA_ADDR, wdata)
|
|
yield
|
|
|
|
|
|
def _test_read(bus, sync=SPI_ACTIVE | SPI_PENDING):
|
|
while (yield from bus.read(SPI_CONFIG_ADDR)) & sync:
|
|
pass
|
|
return (yield from bus.read(SPI_DATA_ADDR))
|
|
|
|
|
|
def _test_gen(bus):
|
|
yield from bus.write(SPI_CONFIG_ADDR,
|
|
0*SPI_CLK_PHASE | 0*SPI_LSB_FIRST |
|
|
1*SPI_HALF_DUPLEX |
|
|
SPI_DIV_WRITE(3) | SPI_DIV_READ(5))
|
|
yield from _test_xfer(bus, 0b01, 4, 0, 0x90000000)
|
|
print(hex((yield from _test_read(bus))))
|
|
yield from _test_xfer(bus, 0b10, 0, 4, 0x90000000)
|
|
print(hex((yield from _test_read(bus))))
|
|
yield from _test_xfer(bus, 0b11, 4, 4, 0x81000000)
|
|
print(hex((yield from _test_read(bus))))
|
|
yield from _test_xfer(bus, 0b01, 8, 32, 0x87654321)
|
|
yield from _test_xfer(bus, 0b01, 0, 32, 0x12345678)
|
|
print(hex((yield from _test_read(bus, SPI_PENDING))))
|
|
print(hex((yield from _test_read(bus, SPI_ACTIVE))))
|
|
return
|
|
for cpol, cpha, lsb, clk in product(
|
|
(0, 1), (0, 1), (0, 1), (0, 1)):
|
|
yield from bus.write(SPI_CONFIG_ADDR,
|
|
cpol*SPI_CLK_POLARITY | cpha*SPI_CLK_PHASE |
|
|
lsb*SPI_LSB_FIRST | SPI_DIV_WRITE(clk) |
|
|
SPI_DIV_READ(clk))
|
|
for wlen, rlen, wdata in product((0, 8, 32), (0, 8, 32),
|
|
(0, 0xffffffff, 0xdeadbeef)):
|
|
rdata = (yield from _test_xfer(bus, 0b1, wlen, rlen, wdata, True))
|
|
len = (wlen + rlen) % 32
|
|
mask = (1 << len) - 1
|
|
if lsb:
|
|
shift = (wlen + rlen) % 32
|
|
else:
|
|
shift = 0
|
|
a = (wdata >> wshift) & wmask
|
|
b = (rdata >> rshift) & rmask
|
|
if a != b:
|
|
print("ERROR", end=" ")
|
|
print(cpol, cpha, lsb, clk, wlen, rlen,
|
|
hex(wdata), hex(rdata), hex(a), hex(b))
|
|
|
|
|
|
class _TestPads:
|
|
def __init__(self):
|
|
self.cs_n = Signal(2)
|
|
self.clk = Signal()
|
|
self.mosi = Signal()
|
|
self.miso = Signal()
|
|
|
|
|
|
class _TestTristate(Module):
|
|
def __init__(self, t):
|
|
oe = Signal()
|
|
self.comb += [
|
|
t.target.eq(t.o),
|
|
oe.eq(t.oe),
|
|
t.i.eq(t.o),
|
|
]
|
|
|
|
if __name__ == "__main__":
|
|
from migen.fhdl.specials import Tristate
|
|
|
|
pads = _TestPads()
|
|
dut = SPIMaster(pads)
|
|
dut.comb += pads.miso.eq(pads.mosi)
|
|
# from migen.fhdl.verilog import convert
|
|
# print(convert(dut))
|
|
|
|
Tristate.lower = _TestTristate
|
|
run_simulation(dut, _test_gen(dut.bus), vcd_name="spi_master.vcd")
|