Network device support packages reference ========================================= PDQ2 ---- Driver ++++++ .. automodule:: artiq.devices.pdq2.driver :members: Mediator ++++++++ .. automodule:: artiq.devices.pdq2.mediator :members: Controller ++++++++++ .. argparse:: :ref: artiq.frontend.pdq2_controller.get_argparser :prog: pdq2_controller Client ++++++ .. argparse:: :ref: artiq.frontend.pdq2_client.get_argparser :prog: pdq2_client Lab Brick Digital Attenuator (LDA) ---------------------------------- On Linux, you need to give your user access to the usb device. You can do that by creating a file under ``/etc/udev/rules.d/`` named ``99-lda.rules`` with the following content:: SUBSYSTEM=="usb", ATTR{idVendor}=="041f", MODE="0666" Then you need to tell udev to reload its rules:: $ sudo invoke-rc.d udev reload You must also unplug/replug your device if it was already plugged in. Then, to run the Lab Brick Digital Attenuator (LDA) controller:: $ lda_controller -d SN:xxxxx The serial number must contain 5 digits, prepend any number of 0 necessary. Also, the ``SN:`` prefix is mandatory. You can chose the exact LDA model with the ``-P`` parameter. The default being LDA-102. Driver ++++++ .. automodule:: artiq.devices.lda.driver :members: Controller ++++++++++ .. argparse:: :ref: artiq.frontend.lda_controller.get_argparser :prog: lda_controller Novatech 409B ------------- Driver ++++++ .. automodule:: artiq.devices.novatech409b.driver :members: Controller ++++++++++ .. argparse:: :ref: artiq.frontend.novatech409b_controller.get_argparser :prog: novatech409b_controller Thorlabs T-Cube --------------- .. _tdc001-controller-usage-example: TDC001 controller usage example +++++++++++++++++++++++++++++++ First, run the TDC001 controller:: $ thorlabs_tcube_controller -P TDC001 -d /dev/ttyUSBx .. note:: On Windows the serial port (the ``-d`` argument) will be of the form ``COMx``. .. note:: Anything compatible `with serial_for_url `_ can be given as a device in ``-d`` argument. For instance, if you want to specify the Vendor/Product ID and the USB Serial Number, you can do: ``-d hwgrep://: SNR=``. The hwgrep URL works on both Linux and Windows. Then, send commands to it via the ``artiq_rpctool`` utility:: $ artiq_rpctool ::1 3255 list-targets Target(s): tdc001 $ artiq_rpctool ::1 3255 call move_relative 10000 # will move forward $ artiq_rpctool ::1 3255 call move_relative -10000 # will move backward $ artiq_rpctool ::1 3255 call move_absolute 20000 # absolute move to 20000 $ artiq_rpctool ::1 3255 call move_home # will go back to home position $ artiq_rpctool ::1 3255 call close # close the device TPZ001 controller usage example +++++++++++++++++++++++++++++++ First, run the TPZ001 controller:: $ thorlabs_tcube_controller -P TPZ001 -d /dev/ttyUSBx .. note:: On Windows the serial port (the ``-d`` argument) will be of the form ``COMx``. .. note:: See the :ref:`TDC001 documentation ` for how to specify the USB Serial Number of the device instead of the /dev/ttyUSBx (or the COMx name). Then, send commands to it via the ``artiq_rpctool`` utility:: $ artiq_rpctool ::1 3255 list-targets Target(s): tpz001 $ artiq_rpctool ::1 3255 call set_output_volts 15 # set output voltage to 15 V $ artiq_rpctool ::1 3255 call get_output_volts # read back output voltage 15 $ artiq_rpctool ::1 3255 call set_tpz_io_settings 150 1 # set maximum output voltage to 150 V $ artiq_rpctool ::1 3255 call set_output_volts 150 # set output voltage to 150 V $ artiq_rpctool ::1 3255 call close # close the device TDC001 Driver +++++++++++++ .. autoclass:: artiq.devices.thorlabs_tcube.driver.Tdc :members: TPZ001 Driver +++++++++++++ .. autoclass:: artiq.devices.thorlabs_tcube.driver.Tpz :members: Controller ++++++++++ .. argparse:: :ref: artiq.frontend.thorlabs_tcube_controller.get_argparser :prog: thorlabs_controller NI PXI6733 ---------- PXI6733 controller usage example ++++++++++++++++++++++++++++++++ This controller has only been tested on Windows so far. To use this controller you need first to install the NI-DAQmx driver from http://www.ni.com/downloads/ni-drivers/f/. Then you also need to install PyDAQmx python module:: $ git clone https://github.com/clade/PyDAQmx $ cd PyDAQmx $ C:\Python34\Tools\Scripts\2to3.py -w . $ python setup.py build $ python setup.py install Then, you can run the PXI6733 controller:: $ pxi6733_controller -d Dev1 Then, send a load_sample_values command to it via the ``artiq_rpctool`` utility:: $ artiq_rpctool ::1 3256 list-targets Target(s): pxi6733 $ artiq_rpctool ::1 3256 call load_sample_values 'np.array([1.0, 2.0, 3.0, 4.0], dtype=float)' This loads 4 voltage values as a numpy float array: 1.0 V, 2.0 V, 3.0 V, 4.0 V Then the device is set up to output those samples at each rising edge of the clock. Driver ++++++ .. automodule:: artiq.devices.pxi6733.driver :members: Controller ++++++++++ Usage example .. argparse:: :ref: artiq.frontend.pxi6733_controller.get_argparser :prog: pxi6733_controller