e31ee1f0b3
firmware/i2c: rewrite I2C implementation
...
* Never drive SDL or SDA high. They are specified to be open
collector/drain and pulled up by resistive pullups. Driving
high fails miserably in a multi-master topology (e.g. with
a USB I2C interface). It would only ever be implemented to
speed up the bus actively but that's tricky and completely
unnecessary here.
* Make the handover states between the I2C protocol phases (start, stop,
restart, write, read) well defined. Add comments stressing those
pre/postconditions.
* Add checks for SDA arbitration failures and stuck SCL.
* Remove wrong, misleading or redundant comments.
2020-07-15 16:43:07 +08:00
4340a5cfc1
rtio/dma: fix previous commit
2020-07-12 10:14:22 +08:00
f2e0d27334
rtio/dma: remove dead/broken code
2020-07-12 10:13:18 +08:00
901be75ba4
sayma_rtm: fix Si5324 reset
...
Closes #1483
2020-07-11 09:51:01 +08:00
8719bab726
Revert "i2c: duplicate TCA9548 control byte"
...
This reverts commit f265976df6
2020-07-08 19:02:02 +08:00
f273a9aacc
artiq_ddb_template: remove SFP LEDs on hw 2.0+
2020-07-08 18:15:36 +08:00
2d1f1fff7f
kasli_generic: do not attempt to use SFP LED for RTIO on 2.0+
2020-07-08 18:14:44 +08:00
85b5a04acf
test: print transfer rates in MiB/s
2020-07-07 17:28:47 +08:00
13501115f6
test: remove watchdog test ( #1458 )
2020-07-07 17:28:47 +08:00
f265976df6
i2c: duplicate TCA9548 control byte
2020-07-03 16:45:05 +08:00
David Nadlinger
3f0cf6e683
runtime: Stop kernel CPU before restarting comms CPU on panic
...
Before, the system would enter a boot loop when a panic occurred
while the kernel CPU was active (and panic_reset == 1), as
kernel::start() for the startup kernel would panic.
2020-07-01 17:29:05 +08:00
95807234d9
compiler: use binutils for ARM
...
This is mostly due to Windoze, where installing anything is a PITA and the LLVM tools won't be available soon.
2020-06-28 17:33:03 +08:00
89c53c35e8
dashboard: style
2020-06-26 10:12:03 +08:00
David Nadlinger
f36692638c
dashboard: Add "Quick Open" dialog for experiments on global shortcut
...
This is similar to functionality in Sublime Text, VS Code, etc.
2020-06-26 10:11:33 +08:00
David Nadlinger
966ed5d013
master/scheduler: Fix priority/due date precedence order when waiting to prepare
...
See test case – previously, the highest-priority pending run would
be used to calculate the timeout, rather than the earliest one.
This probably managed to go undetected for that long as any unrelated
changes to the pipeline (e.g. new submissions, or experiments pausing)
would also cause _get_run() to be re-evaluated.
2020-06-19 23:45:52 +01:00
David Nadlinger
7955b63b00
master: Always write results to HDF5 once run stage is reached
...
Previously, a significant risk of losing experimental results would
be associated with long-running experiments, as any stray exceptions
while run()ing the experiment – for instance, due to infrequent
network glitches or hardware reliability issue – would cause no
HDF5 file to be written. This was especially troublesome as long
experiments would suffer from a higher probability of unanticipated
failures, while at the same time being more costly to re-take in
terms of wall-clock time.
Unanticipated uncaught exceptions like that were enough of an issue
that several Oxford codebases had come up with their own half-baked
mitigation strategies, from swallowing all exceptions in run() by
convention, to always broadcasting all results to uniquely named
datasets such that the partial results could be recovered and written
to HDF5 by manually run recovery experiments.
This commit addresses the problem at its source, changing the worker
behaviour such that an HDF5 file is always written as soon as run()
starts.
2020-06-18 17:47:26 +01:00
David Nadlinger
d87042597a
master/worker_impl: Factor out "completed" message sending [nfc]
...
Just reduces the visual complexity/potential for typos a bit, and
we already have put_exception_report().
2020-06-18 01:30:46 +01:00
charlesbaynham
2429a266f6
ad9912: Fix typing problem on ad9912 ( #1466 )
...
Closes #1463
FTW and phase word were ambiguously typed, resulting in failure to compile
2020-06-16 20:17:22 +02:00
Harry Ho
1a17d0c869
zotino: add USER LED test
2020-06-11 16:03:56 +08:00
Harry Ho
6156bd4088
fastino: add tests using DACs and USER LEDs
2020-06-11 14:55:46 +08:00
a18d2468e9
test: do not build libartiq_support in lit.cfg
2020-06-10 17:15:24 +08:00
9822b88d9b
ad9910: fix asf range ( #1450 )
...
* ad9910: fix asf range
The ASF is a 14-bit word. The highest possible value is 0x3fff, not
0x3ffe. `int(round(1.0 * 0x3fff)) == 0x3fff`.
I don't remember and understand why this was 0x3ffe since the beginning.
0x3fff was already used as a default in `set_mu()`
Signed-off-by: Robert Jördens <rj@quartiq.de>
* RELEASE_NOTES: ad9910 asf scale change
Co-authored-by: David Nadlinger <code@klickverbot.at>
2020-05-29 11:13:26 +02:00
cb76f9da89
metlino: fix CSR collisions
...
Closes #1425
2020-05-29 15:59:44 +08:00
bd9eec15c0
metlino: increase number of DRTIO links
...
Seems OK with Vivado 2019.2.
2020-05-29 15:59:16 +08:00
d5c1eaa16e
runtime: remove stack alignment requirement
...
I suppose this was for TMPU, but was never finished.
2020-05-29 15:37:23 +08:00
02900d79d0
firmware: fix typos
2020-05-29 15:21:07 +08:00
d8b5bcf019
sayma_amc: support uTCA backplane for DRTIO
2020-05-29 14:58:49 +08:00
8b939b7cb3
sayma_amc: remove Master (obsoleted by Metlino)
2020-05-29 14:40:49 +08:00
Charles Baynham
692c466838
Use logger formatting
2020-05-26 17:59:55 +08:00
Charles Baynham
8858ba8095
dashboard: Restart applets if required
...
Restart applets that are already running if a ccb call updates their spec
Signed-off-by: Charles Baynham <charles.baynham@npl.co.uk>
2020-05-26 17:59:55 +08:00
2538840756
Coredevice Input Validation ( #1447 )
...
* Input validation and masking of SI -> mu conversions (close #1446 )
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* Update RELEASE_NOTES
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
Co-authored-by: Robert Jördens <rj@quartiq.de>
2020-05-17 15:09:11 +02:00
b3b6cb8efe
ad53xx improvements ( #1445 )
...
* ad53xx: voltage_to_mu() validation & documentation (closes #1443 , #1444 )
The voltage input (float) is checked for validity. If we need more
speed, we may want to check the DAC-code for over/underflow instead.
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* ad53xx documentation: voltage_to_mu is only valid for 16-bit DACs
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* AD53xx: add voltage_to_mu method (closes #1341 )
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* ad53xx: improve voltage_to_mu performance
Interger comparison is faster than floating point math.
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* AD53xx: voltage_to_mu method now uses attribute values
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* Fixup RELEASE_NOTES.rst
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* ad53xx: documentation improvements
voltage_to_mu return value
14-bit DAC support
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
2020-05-08 19:23:43 +02:00
4e9a529e5a
kasli: integrate WRPLL
2020-05-07 21:34:02 +08:00
60e5f1c18e
kasli: DRTIO support for Kasli 2
2020-05-07 20:09:43 +08:00
1f2182d4c7
kasli: default to hardware v2
2020-05-07 19:15:03 +08:00
35f1814235
kasli: implement virtual LEDs
2020-05-07 19:07:43 +08:00
b83afedf43
kasli: light up ERROR LED on panic
2020-05-07 19:06:10 +08:00
4982fde898
firmware: I2C I/O expander support
2020-05-05 21:38:17 +08:00
ef4e5bc69b
firmware: Kasli I2C EEPROM cleanup
2020-05-05 21:29:29 +08:00
85e92ae28c
compiler: use more LLVM tools on ARM ( #733 )
2020-04-28 16:21:50 +08:00
7e400a78f4
kasli: compile tester for hw 2.0 by default
2020-04-28 16:07:56 +08:00
140a26ad7e
compiler: ld -> ld.lld
2020-04-28 16:07:26 +08:00
4228e0205c
compiler: link with lld on ARM ( #733 )
2020-04-28 15:00:24 +08:00
3a7819704a
rtio: support direct 64-bit now CSR in KernelInitiator
2020-04-26 16:04:32 +08:00
251a0101a6
compiler: support disabling now-pinning
2020-04-26 12:38:43 +08:00
d19f28fa84
kasli: v2 clocking WIP, remove SFP LEDs from RTIO
2020-04-23 23:02:18 +08:00
9bc43b2dbf
kasli: support EEPROM on v2
2020-04-23 23:00:36 +08:00
77e6fdb7a7
artiq_flash: cleanup Sayma RTM management, support flashing AMC with RTM disconnected
2020-04-14 18:22:06 +08:00
ea79ba4622
ttl_serdes: detect edges on short pulses
...
Edges on pulses shorter than the RTIO period were missed because the
reference sample and the last sample of the serdes word are the same.
This change enables detection of edges on pulses as short as the
serdes UI (and shorter as long as the pulse still hits a serdes sample
aperture).
In any RTIO period, only the leading event corresponding to the first
edge with slope according to sensitivity is registerd. If the channel is
sensitive to both rising and falling edges and if the pulse is contained
within an RTIO period, or if it is sensitive only to one edge slope and
there are multiple pulses in an RTIO period, only the leading event is
seen. Thus this possibility of lost events is still there. Only the
conditions under which loss occurs are reduced.
In testing with the kasli-ptb6 variant, this also improves resource
usage (a couple hundred LUT) and timing (0.1 ns WNS).
2020-04-13 13:21:03 +02:00
e8b73876ab
comm_kernel: add Zynq runtime identifier
2020-04-12 17:25:14 +08:00
de57039e6e
comm_kernel: cleanup
2020-04-12 16:02:36 +08:00
9dc24f255e
comm_kernel: remove dead code
2020-04-12 15:06:46 +08:00
fb0ade77a9
firmware: fix non-DRTIO build
2020-04-10 17:23:17 +08:00
ec7b2bea12
sayma: round FTW like Urukul in JDCGSyncDDS
2020-04-08 15:00:33 +08:00
0f4be22274
sayma: add simple sychronized DDS for testing
2020-04-08 14:13:54 +08:00
3c823a483a
sayma: improve DAC sync messaging (again)
2020-04-06 22:36:43 +08:00
4d601c2102
sayma: improve DAC sync messaging
2020-04-06 22:36:03 +08:00
61d4614b61
sayma: fix/cleanup DRTIO-DAC sync interaction
2020-04-06 22:34:05 +08:00
facc0357d8
drtio: make sure receive buffer is drained after ping reply
2020-04-06 22:33:15 +08:00
ffd3172e02
sayma: move SYSREF DDMTD to RTM ( #795 )
2020-04-06 00:01:28 +08:00
8f608fa2fa
examples/sines_urukul_sayma: adapt for sayma v2, use 1 DAC only
2020-04-05 16:51:40 +08:00
Etienne Wodey
90d08988b2
language/environment: BooleanValue: fix type detection
...
Signed-off-by: Etienne Wodey <wodey@iqo.uni-hannover.de>
2020-04-04 15:37:04 +08:00
Etienne Wodey
9b03a365ed
language/environment: cast argument processor default values early
...
Fixes #1434 . Also add unit tests for some argument processors.
Signed-off-by: Etienne Wodey <wodey@iqo.uni-hannover.de>
2020-04-04 15:37:04 +08:00
4a8d361ace
soc: optimize programmable identifier
2020-03-12 23:09:13 +08:00
9e66dd7075
soc: reprogrammable identifier
2020-03-12 22:23:08 +08:00
380de177e7
rtio: fix wide output after RTIO refactoring
...
fixes 3d0c3cc1cf
2020-03-05 17:55:27 +00:00
e803830b3b
fastino: support wide RTIO interface and channel groups
2020-03-05 17:55:04 +00:00
8451e58fbe
ad9912: fix ftw width docstring
2020-02-27 02:11:12 +08:00
Paweł K
2a909839ff
artiq_flash: added option of specifying another username when connecting through SSH. ( #1429 )
...
Signed-off-by: Paweł Kulik <pawel.kulik@creotech.pl>
2020-02-19 19:44:11 +08:00
6d26def3ce
sayma: drive filtered_clk_sel on master variant
2020-02-06 22:28:49 +08:00
52ec849008
sayma: fix sysref_delay_dac
2020-02-05 19:04:01 +08:00
c7de1f2e6b
metlino: drive clock muxes
2020-02-05 00:06:34 +08:00
bf9f4e380a
si5324: program I2C mux on Metlino
2020-02-03 18:07:59 +08:00
ffb24e9fff
artiq_flash: use correct proxy bitstream for Metlino
2020-02-03 18:07:26 +08:00
5f8e20b1a1
artiq_sinara_tester: fix device_db filename
2020-01-31 10:26:58 +08:00
dfa033eb87
wrpll: new collector from Weida/Tom
2020-01-24 10:31:52 +08:00
dee16edb78
wrpll: DDMTD sampler double latching
2020-01-22 19:16:26 +08:00
f4d8f77268
turn kasli_tester into a frontend tool
2020-01-21 16:13:04 +08:00
bfcbffcd8d
update smoltcp
...
This disables the 'log' features which does not compile, and may break net_trace. To be investigated later.
2020-01-21 13:58:23 +08:00
82cdb7f933
typo
2020-01-21 10:07:13 +08:00
248230a89e
fastino: style
2020-01-20 13:25:00 +01:00
c45a872cba
fastino: fix init, set_cfg
2020-01-20 13:25:00 +01:00
2c4e5bfee4
fastino: add [WIP]
2020-01-20 13:25:00 +01:00
8f9948a1ff
kasli_sawgmaster: add basemod programming example
2020-01-20 20:14:24 +08:00
e427aaaa66
basemod_att: fix imports
2020-01-20 20:14:24 +08:00
62a52cb086
sayma: do not pollute the log with DAC status on success
2020-01-20 20:14:24 +08:00
6b428ef3be
sayma: initialize DAC before testing jesd::ready
2020-01-20 20:14:24 +08:00
7ab0282234
adf5355: style
2020-01-20 13:13:08 +01:00
9368c26d1c
mirny: add to manual
2020-01-20 13:13:08 +01:00
Etienne Wodey
da531404e8
artiq_ddb_template: add Mirny support
...
Signed-off-by: Etienne Wodey <wodey@iqo.uni-hannover.de>
2020-01-20 13:13:08 +01:00
01a6e77d89
mirny: add
...
* This targets unrelease CPLD gateware (https://github.com/quartiq/mirny/issues/1 )
* includes initial coredevice driver, eem shims, and kasli_generic tooling
* addresses the ARTIQ side of #1130
* Register abstraction to be written
Signed-off-by: Robert Jördens <rj@quartiq.de>
2020-01-20 13:13:08 +01:00
ec03767dcf
sayma: improve DAC status report
2020-01-20 18:22:06 +08:00
5c299de3b4
sayma: print DAC status on JESD not ready error
2020-01-20 18:21:29 +08:00
45efee724e
sayma: add JESD204 PHY done diagnostics
2020-01-20 12:47:31 +08:00
6c3e71a83a
wrpll: cleanup
2020-01-18 09:43:43 +08:00
344f8bd12a
wrpll: collector patch from Weida
2020-01-18 09:42:58 +08:00
833f428391
sayma: fix hmc542 to/from mu
2020-01-16 09:10:32 +08:00
6c948c7726
sayma: RF switch control is active-low on Basemod, invert
2020-01-16 08:59:52 +08:00
50302d57c0
wrpll: more careful I2C timing
2020-01-14 20:03:46 +08:00
105dd60c78
wrpll: ADPLLProgrammer mini test bench and fixes
2020-01-14 16:52:25 +08:00
3242e9ec6c
wrpll: loop test
2020-01-13 22:31:57 +08:00
8ec0f2e717
wrpll: implement ADPLLProgrammer
2020-01-13 22:30:11 +08:00
d5895b8999
wrpll: adpll -> set_adpll
2020-01-13 20:46:36 +08:00
e7ef23d30c
wrpll: use CONFIG_CLOCK_FREQUENCY and rtio_frequency in trim_dcxos
2020-01-13 20:44:15 +08:00
ea3bce6fe3
wrpll: wait for settling time after setting ADPLL
2020-01-13 20:43:34 +08:00
d685619bcd
wrpll: collector code modifications from Weida
2020-01-13 20:42:41 +08:00
9d7196bdb7
update copyright year
2020-01-13 19:33:44 +08:00
e87d864063
wrpll: print ADPLL offsets
2020-01-13 19:32:30 +08:00
8edbc33d0e
wrpll: calculate initial ADPLL offsets
2020-01-13 19:29:10 +08:00
9dd011f4ad
firmware: remove bitrotten Sayma code
2020-01-13 18:47:54 +08:00
583a18dd5f
firmware: expose fmod to kernels. Closes #1417
2020-01-10 14:33:02 +08:00
David Nadlinger
d8c81d6d05
compiler: Other types microoptimisations
...
Interestingly enough, these actually seem to give a measurable
speedup (if small – about 1% improvement out of 6s whole-program
compile-time in one particular test case).
The previous implementation of is_mono() had also interesting
behaviour if `name` wasn't given; it would test only for the
presence of any keys specified via keyword arguments,
disregarding their values. Looking at uses across the current
ARTIQ codebase, I could neither find a case where this would
have actually been triggered, nor any rationale for it.
With the short-circuited implementation from this commit,
is_mono() now checks name/all of params against any specified
conditions.
2020-01-01 08:49:19 +00:00
David Nadlinger
2c34f0214b
compiler: Short-circuit Type.unify() with identical other type
...
This considerably improves performance; ~15% in terms of total
artiq_run-to-kernel-compiled duration in one test case.
2020-01-01 08:49:19 +00:00
eebae01503
artiq_client: add back quiet-verbose args for submission
...
close #1416
regression introduced in 3fd6962
2019-12-31 13:00:26 +01:00
3f32d78c0e
wrpll: simple ADPLL test
2019-12-31 12:12:29 +08:00
bb04b082a7
wrpll: clarify comment
2019-12-31 12:12:29 +08:00
David Nadlinger
1e864b7e2d
coredevice/suservo: Add separate methods for setting only the IIR offset
2019-12-30 20:02:22 +00:00
a666766f38
wrpll: add ADPLL offset registers
2019-12-30 22:19:42 +08:00
5c6e394928
ddmtd: add collector
2019-12-30 22:17:44 +08:00
642a305c6a
wrpll: remove unnecessary delay
...
Counting now happens in the sys domain with no CDC between counter and CPU.
2019-12-30 20:01:06 +08:00
f57f235dca
wrpll: new frequency meter
...
As per Mattermost discussion with Tom.
2019-12-30 19:47:57 +08:00
9e15ff7e6a
wrpll: improve DDMTD deglitcher
2019-12-30 16:56:06 +08:00
dfad27125e
runtime: relax/fix TCP keepalive settings ( #1125 )
2019-12-23 19:58:10 +08:00
b5e1bd3fa2
coredevice: simplify/cleanup network connection code
...
This removes:
* host-side keepalive, which turns out not to be required
* custom connection timeout (the default is OK)
* SSH tunneling support (doesn't seem to be actually used anywhere)
2019-12-23 19:53:49 +08:00
David Nadlinger
af31c6ea21
coredevice: Don't use is to compare with integer literal
...
This works on CPython, but is not guaranteed to do so, and
produces a warning since 3.8 (see https://bugs.python.org/issue34850 ).
2019-12-22 05:46:41 +00:00
fb2076a026
basemod_att: add dB functions, document
2019-12-21 14:56:41 +08:00
b2480f0edc
artiq_flash: update actions documentation
2019-12-21 14:18:28 +08:00
d4e039cede
basemod: add coredevice driver
2019-12-21 14:18:10 +08:00
106d25b32a
kasli_sawgmaster: fix drtio_is_up
2019-12-21 14:17:52 +08:00
8759c8d360
shiftreg: fix get method
2019-12-21 14:17:22 +08:00
c3030f4ffb
kasli_sawgmaster: update device_db for BaseMod
2019-12-20 19:59:15 +08:00
cab8c8249e
coredevice/shiftreg: add get method
2019-12-20 18:58:50 +08:00
b7f1623197
sayma_rtm: connect attenuator shift registers in series
2019-12-20 18:58:31 +08:00
c5137eeb62
firmware: remove legacy hmc542 code
2019-12-20 15:25:55 +08:00
1c9cbe6285
sayma_rtm: add basemod attenuators on RTIO
2019-12-20 15:25:55 +08:00
David Nadlinger
8f518c6b05
compiler: Allow None in type hints
...
Similar to how Python itself interprets None as type(None),
make it translate to TNone in ARTIQ compiler type hints.
2019-12-19 09:36:45 +08:00
David Nadlinger
594ff45750
compiler: Revert support for None as TNone
...
This was mistakenly included in fb2b634c4a
2019-12-18 13:23:40 +00:00
David Nadlinger
fb2b634c4a
compiler, language: Implement @kernel_from_string
...
With support for polymorphism (or type erasure on pointers to
member functions) being absent in the ARTIQ compiler, code
generation is vital to be able to implement abstractions that
work with user-provided lists/trees of objects with uniform
interfaces (e.g. a common base class, or duck typing), but
different concrete types.
@kernel_from_string has been in production use for exactly
this use case in Oxford for the better part of a year now
(various places in ndscan).
GitHub: Fixes #1089 .
2019-12-18 10:51:04 +08:00
6ee15fbcae
sayma_rtm: basemod RF switches
2019-12-18 10:33:29 +08:00
David Nadlinger
d3508b014f
firmware: Add whitespace between panic handler location and message
2019-12-17 19:59:59 +00:00
David Nadlinger
0279a60a55
examples: Add README
...
This will be displayed by GitHub below the directory listing, and was
inspired by observing new users disregard the examples/ tree entirely
(even though the experiments and device DBs within would have cleared
up their getting-started confusion) due to the perceived complexity
wall induced by the wealth of subdirectories.
2019-12-17 13:35:19 +00:00
8d13aeb96c
test: run test_help for browser and dashboard
2019-12-12 10:34:58 +08:00
ac09f3a5da
artiq_browser: fix command line argument handling. Closes #1404
2019-12-11 16:18:56 +08:00
52112d54f9
kasli_generic: expose peripheral_processors dictionary. Closes #1403
2019-12-10 10:30:06 +08:00
6f52540569
wrpll: fix previous commit
2019-12-09 20:13:55 +08:00
13486f3acf
wrpll: swap helper/main si549 frequencies
2019-12-09 19:49:34 +08:00
150a02117c
sayma_rtm: drive clk_src_ext_sel
2019-12-09 19:47:50 +08:00
307a6ca140
gth_ultrascale: make OBUFDS_GTE3 work
...
https://www.xilinx.com/support/answers/67919.html
2019-12-09 18:13:22 +08:00
4919fb8765
wrpll: print DDMTD helper tags
2019-12-09 17:39:22 +08:00
0d4eccc1a5
wrpll: improve debug output
2019-12-09 17:23:09 +08:00
f633c62e8d
wrpll: speed up si549 i2c access
2019-12-09 17:22:58 +08:00
14e09582b6
wrpll: work around si549 not working when lsdiv=2
2019-12-09 16:20:08 +08:00
439576f59d
wrpll: fix Si549 initialization delays
2019-12-09 16:13:57 +08:00
2b5213b013
wrpll: constrain clocks
2019-12-09 12:26:44 +08:00
05e2e1899a
wrpll: update OBUFDS_GTE2 comment
...
Seems O can fan out simultaneously to transceiver and fabric.
Kasli is using ODIV2 for no particular reason.
2019-12-09 11:58:54 +08:00
4148efd2ee
wrpll: implement filters and connect to Si549
2019-12-09 11:47:29 +08:00
d43fe644f0
wrpll: stabilize DDMTDSamplerGTP
2019-12-09 11:47:14 +08:00
0499f83580
wrpll: helper clock sanity check
2019-12-08 23:46:33 +08:00
46a776d06e
sayma: introduce WRPLL on RTM
2019-12-08 15:30:00 +08:00
f35f658bc5
artiq_flash: rework RTM management
2019-12-08 15:29:31 +08:00
bcd061f141
artiq_flash: RTM is a regular DRTIO satellite, can be used with all variants
2019-12-08 15:12:04 +08:00
883310d83e
sayma_rtm: si5324 -> cdrclkc
2019-12-08 14:26:05 +08:00
57a5bea43a
sayma_rtm: support setting RTIO frequency
2019-12-08 11:45:31 +08:00
da9237de53
wrpll: support differential DDMTD inputs
2019-12-07 18:18:57 +08:00
Paweł Kulik
3851a02a3a
Added option of flashing only RTM gateware.
...
Signed-off-by: Paweł Kulik <pawel.kulik@creotech.pl>
2019-12-07 09:31:19 +08:00
Paweł Kulik
14e250c78f
Enabled internal pullup for CML SYSREF outputs, otherwise there is no signal on them.
...
Signed-off-by: Paweł Kulik <pawel.kulik@creotech.pl>
2019-12-07 09:30:24 +08:00
7098854b0f
wrpll: share DDMTD counter
2019-12-04 19:05:56 +08:00
05c5fed07d
suservo: stray comma
2019-12-03 08:38:07 +00:00
56074cfffa
suservo: support operating with one urukul
...
implemented by wiring up the second Urukul to dummy pins
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-12-02 11:30:20 +01:00
86e1924493
kasli_generic: support external reference on masters
2019-11-30 07:34:41 +00:00
eb271f383b
wrpll: add DDMTD cores
2019-11-28 22:03:50 +08:00
39d5ca11f4
si549: increase I2C frequency
2019-11-28 22:03:26 +08:00
87894102e5
si549: use recommended i2c read sequence
2019-11-28 17:49:02 +08:00
2e55e39ac7
wrpll: use spaces to indent
2019-11-28 17:40:25 +08:00
354d82cfe3
wrpll: drive helper clock domain
2019-11-28 17:40:00 +08:00
4a03ca928d
artiq_flash: sayma fixes
2019-11-28 17:38:29 +08:00
68cab5be8c
si549: cleanups
2019-11-28 16:36:59 +08:00
bcd2383c9d
wrpll: si549 initialization
2019-11-27 22:58:08 +08:00
4832bfb08c
wrpll: i2c functions, select_recovered_clock placeholder
2019-11-27 21:21:00 +08:00
449d2c4f08
libboard_misoc: fix !has_i2c
2019-11-27 21:04:28 +08:00
e0687b77f5
si5324: 10 MHz ext_ref_frequency
...
* close #1254
* tested on innsbruck2 kasli variant
* sponsored by Uni Innsbruck/AQT
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-11-22 18:29:12 +01:00
c536f6c4df
sayma_amc: output ddmtd_rec_clk
2019-11-20 19:16:04 +08:00
ae50da09c4
drtio/gth_ultrascale: support OBUFDS_GTE3
2019-11-20 19:15:50 +08:00
fe0c324b38
sayma: integrate si549 core
2019-11-20 17:37:16 +08:00
fa41c946ea
wrpll: si549 fixes
2019-11-20 17:04:24 +08:00
c5dbab1929
gateware: move wrpll to drtio
2019-11-20 14:43:08 +08:00
gthickman
56d4b70e01
ad9910 osk ( #1387 )
...
* updated adoo10.py for RAM mode frequency control
* updated docstrings for set_cfr1() in ad9910.py
* fixed typo in ad9910.py
* added docstrings to ad9910.py
* removed OSK-related changes in AD9910, to be included in a separate branch.
* updated AD9910 set_cfr1 for control of OSK mode parameters
* updated AD9910 set_cfr1() for control of OSK mode parameters.
2019-11-18 15:57:26 +01:00
Fabian Schmid
f73e2a3d30
doc: clarify urukul attenuator behavior
...
Closes #1386
Signed-off-by: Fabian Schmid <fabian.schmid@mpq.mpg.de>
2019-11-18 15:56:00 +01:00
3adc799785
update GUI background
2019-11-15 13:49:09 +08:00
db13747279
fix device_db alias corner case bugs. Closes #1140
2019-11-14 16:22:45 +08:00
4707aef45c
split out artiq-comtools
2019-11-14 15:21:51 +08:00
4416378d21
frontend: add --version to common tools
2019-11-14 11:42:31 +08:00
Garrett
f8a7e278b8
removed OSK-related changes in AD9910, to be included in a separate branch.
2019-11-12 19:07:05 +01:00
Garrett
3a19ba7e62
added docstrings to ad9910.py
2019-11-12 19:07:05 +01:00
Garrett
4ad3651022
fixed typo in ad9910.py
2019-11-12 19:07:05 +01:00
Garrett
6d34eb3bb0
updated docstrings for set_cfr1() in ad9910.py
2019-11-12 19:07:05 +01:00
Garrett
61ca46ec3f
updated adoo10.py for RAM mode frequency control
2019-11-12 19:07:05 +01:00
fd7081830c
remove fire_and_forget (moved to sipyco)
2019-11-12 19:43:04 +08:00
3fd6962bd2
use sipyco ( #585 )
2019-11-10 15:55:17 +08:00
6644903843
bootloader: fix imports
2019-11-06 14:45:55 +08:00
5279bc275a
urukul: rework EEPROM synchronization. Closes #1372
2019-11-05 18:56:10 +08:00
David Nadlinger
bc3b55b1a8
gateware/eem: Force IOB=TRUE on Urukul SYNC output
...
Without this, the final register in the SYNC signal TTLClockGen
isn't (always) placed in the I/O tile, leading to more jitter
than necessary, and causing "double window" artefacts. See
sinara-hw/Urukul#16 for more details.
(Patch based on work by Weida Zhang, testing by various members
of the community in Oxford and elsewhere.)
2019-11-05 17:14:07 +08:00
b25a17fa37
netboot: support slave FPGA loading
2019-11-05 16:28:49 +08:00
307f39e900
remoting: fix multiuser access. Closes #1383
2019-11-05 15:46:07 +08:00
9dc82bd766
bootloader: add no_flash_boot config option to force network boot
2019-11-05 15:31:08 +08:00
e2f9f59472
artiq_flash: fix flashing Sayma RTM from package
2019-11-05 15:19:01 +08:00
98854473dd
sayma_amc: use all transceivers on master ( #1230 )
2019-11-02 12:12:32 +08:00
29b4d87943
firmware: add cargosha256.nix
2019-11-01 10:28:41 +08:00
5362f92b39
bootloader: disable minimum stack space check in linker script
...
* The value varies greatly whether netboot is enabled or not.
* There is no simple solution to detect has_ethmac in the linker script and set the value accordingly.
* The space check is an imperfect solution that will be superseded by stack pointer limits.
* Left commented out so we can re-enable it manually during development if stack corruption is suspected.
2019-11-01 10:25:14 +08:00
deadfead2a
bootloader: fix !has_ethmac
2019-11-01 10:19:08 +08:00
42af76326f
kasli: enlarge integrated CPU SRAM for DRTIO masters
...
Required by the bootloader netboot support.
2019-11-01 10:15:13 +08:00
a78e493b72
firmware: load slave FPGA in bootloader
2019-10-31 12:42:40 +08:00
389a8f587a
slave_fpga: modularize
2019-10-31 11:50:53 +08:00
9a35a2ed81
test_frontends: update
2019-10-30 22:02:16 +08:00
bc050fdeec
bootloader: treat zero-length firmware in flash as no firmware
2019-10-30 21:46:06 +08:00
228e44a059
sayma: enable Ethernet on DRTIO satellite variant
...
So that netboot can be used in bootloader.
2019-10-30 21:39:00 +08:00
dc71039934
sayma, metlino: increase integrated_sram_size on Ethernet-enabled variants
2019-10-30 21:36:00 +08:00
3042476230
artiq_netboot: remove unnecessary import
2019-10-30 21:29:33 +08:00
c96de7454d
remove artiq_devtool
2019-10-30 21:27:24 +08:00
88dbff46f4
add netboot tool
2019-10-30 21:24:51 +08:00
462cf5967e
bootloader: add netboot support
2019-10-30 21:23:42 +08:00
1f15e55021
comm_analyzer: don't assume every message has data
...
close #1377
2019-10-28 15:35:44 +01:00
David Nadlinger
611bcc4db4
compiler: Cache expensive target data layout queries
...
On one typical experiment, this shaves about 3 seconds (~25%)
off the overall kernel compilation time.
GitHub: Closes #1370 .
2019-10-28 11:09:25 +00:00
David Nadlinger
5d7f22ffa4
compiler: Remove provision for unused four-parameter llptr_to_var() form [nfc]
...
`var_type` was presumably intended to convert to a target type,
but wasn't actually acted on in the function body (nor was it
used anywhere in the codebase).
2019-10-28 11:02:46 +00:00
f2f7170d20
hmc7043: use recommend I/O standards
...
https://github.com/sinara-hw/Sayma_RTM/issues/116#issuecomment-544187952
2019-10-21 22:56:10 +08:00
47a83c71f1
firmware: more readable network addresses message
2019-10-21 14:00:14 +08:00
818d6b2f5a
bootloader: fix compilation problems
2019-10-21 13:28:17 +08:00
8f76a3218e
firmware: move i2c to libboard_misoc, enable IPv6 in bootloader, share network settings
2019-10-21 12:58:52 +08:00
1c5e749036
satman: remove compilation warning without JESD DACs
2019-10-21 12:53:54 +08:00
d26d80410e
runtime: refactor network settings
2019-10-19 17:56:35 +08:00
6d5dcb4211
runtime: enable IPv6. Closes #349
2019-10-19 17:20:33 +08:00
05e8f24c24
sayma2: JESD204 synchronization
2019-10-18 23:28:47 +08:00
62b49882b9
examples/kc705: fix dds_test
2019-10-17 07:37:00 +08:00
a8f85860c4
coreanalyzer: AD9914 fixes ( #1376 )
2019-10-17 07:29:33 +08:00
d42ff81144
examples/sayma_master: update device_db
2019-10-16 18:49:25 +08:00
8fa3c6460e
sayma_amc: set direction of external TTL buffer according to RTIO PHY OE
2019-10-16 18:48:50 +08:00
37d0a5dc19
rtio/ttl: expose OE
2019-10-16 18:48:20 +08:00
bc060b7f01
style
2019-10-16 18:18:11 +08:00
40d64fc782
sayma: remove standalone examples (no longer supported)
2019-10-16 17:54:39 +08:00
21a1c6de3f
sayma: use SFP0 for DRTIO master
2019-10-16 17:53:40 +08:00
6cf06fba7b
examples: use default IP addresses for boards
2019-10-16 16:18:30 +08:00
314d9b5d06
kasli: default to 125MHz frequency for DRTIO
...
This is the consistent and most common option. Sayma will also eventually move to it.
2019-10-08 12:59:52 +08:00
4df2c5d1fb
sayma: prepare for SYSREF align
...
We will try DDMTD on the AMC first, as this is simpler and perhaps will work on v2 after the power supply fixes.
2019-10-08 12:30:47 +08:00
5ee81dc643
satman: define constants for JdacBasicRequest reqnos
2019-10-08 10:27:04 +08:00
4b3baf4825
firmware: run PRBS and STPL JESD204 tests
2019-10-08 00:10:36 +08:00
03007b896e
sayma_amc: sma -> mcx
2019-10-07 20:31:35 +08:00
ebd5d890f1
satman: check for JESD ready
2019-10-06 23:10:57 +08:00
90e3b83e80
hmc7043: turn on AMC_FPGA_SYSREF1
...
Florent's JESD core won't work at all without.
2019-10-06 22:49:00 +08:00
97a0dee3e8
jesd204: remove ibuf_disable
...
We use the MOSFET to mute the HMC7043 noise on hardware v2 instead.
2019-10-06 22:26:31 +08:00
1bc7743e03
sayma: fix hmc7043 output settings for v2 hardware
2019-10-06 21:50:29 +08:00
a421820a32
sayma: initialize DACs over DRTIO
2019-10-06 21:42:45 +08:00
f8e4cc37d0
sayma_rtm: reset and detect DACs
2019-10-06 20:15:27 +08:00
f62dc7e1d4
sayma: refactor JESD DAC channel groups
2019-10-06 20:15:09 +08:00
c4c884b8ce
ad9154: simplify, focus on AD9154 config and do not include JESD
2019-10-06 20:07:02 +08:00
fdba0bfbbc
satman: move now-unrelated hmc830_7043 init away from DRTIO transceiver init
2019-10-06 19:22:46 +08:00
1c6c22fde9
sayma_amc: HMC830_REF moved to RTM side
2019-10-06 18:15:37 +08:00
ad63908aff
hmc830_7043: enable_fpga_ibuf -> unmute
2019-10-06 18:13:59 +08:00
5ad65b9d30
hmc830_7043: remove clock_mux
2019-10-06 18:13:27 +08:00
e6ff44301b
sayma_amc: cleanup (v2.0 only)
2019-10-06 18:11:43 +08:00
e9b81f6e33
remove serwb
...
DRTIO is a better solution
2019-10-06 18:10:23 +08:00
7cd02d30b7
sayma_rtm_drtio: replace sayma_rtm
2019-10-06 17:59:53 +08:00
b3b85135a3
sayma_rtm_drtio: add DDMTD core, move specific cores out of SatelliteBase
2019-10-06 17:59:11 +08:00
346c985347
sayma_rtm_drtio: use artiq_sayma folder
2019-10-06 17:30:08 +08:00
e2a924449d
artiq_flash: use DRTIO RTM gateware
2019-10-06 17:28:14 +08:00
4198033657
sayma_rtm_drtio: cleanup (v2.0 only)
2019-10-06 16:42:34 +08:00
5612b31860
sayma_rtm_drtio: add HMC clock chip and DAC control
2019-10-06 16:15:24 +08:00
a8cf4c2b18
sayma_rtm: hwrev v2.0 by default
2019-10-06 13:25:30 +08:00
1bc5d44a7c
artiq_flash: do not flash RTM gateware on Sayma variants that don't need it
2019-10-06 13:15:50 +08:00
bb5ff46f7d
Merge branch 'wrpll'
2019-10-05 10:24:11 +08:00
7b95814cf5
sayma_amc: refactor, add SimpleSatellite variant
2019-10-05 10:24:06 +08:00
58b7bdcecc
sayma_amc: refactor RTM FPGA code
2019-10-05 10:24:06 +08:00
96fc4a21e8
sayma_amc: remove dummy FPGA pin assignment testing code
2019-10-05 10:24:06 +08:00
Tim Ballance
ada3b39f4e
Fix ad9910 ram mode asf scale error in polar mode
2019-10-04 20:14:41 +02:00
Tim Ballance
448080e71d
Fix ad9910 ram mode asf scale error
...
RAM mode amplitude to ASF conversion should be << 18 rather than << 16
2019-10-04 20:14:41 +02:00
6aa68e1715
sayma_rtm2: select filtered clock from Si5324
2019-10-04 22:56:16 +08:00
6cb0f5de59
sayma_amc: enable DRTIO switching
2019-10-04 22:55:23 +08:00
0cf8a46bbd
sayma_amc2: select filtered clock from Si5324
2019-10-04 21:28:26 +08:00
6f533727cb
artiq_flash: use regular bscan_spi_xcku040 for Sayma
...
The modified version is no longer necessary on v2 boards, and breaks flash bank 1.
2019-10-04 17:50:45 +08:00
4c1fe1de0d
environment: implement HasEnvironment.call_child_method ( #1366 )
2019-09-30 23:58:36 +08:00
Charles Baynham
0b1fb255a9
tools: Wrap Task _do() calls in a generic exception handler
...
Signed-off-by: Charles Baynham <charles.baynham@npl.co.uk>
2019-09-20 23:00:59 +08:00
Charles Baynham
e50a6d5aaf
worker_impy: ignore newline at start of experiment docstring
2019-09-20 22:10:49 +08:00
f0e87d2e59
grabber: remove unused code
2019-09-20 15:26:12 +02:00
4e77be0511
firmware: add Cargo.lock header that newer cargo wants
2019-09-17 15:22:14 +08:00
Charles Baynham
b7abf2fb53
pyon: Handle inf in decoding
2019-09-12 09:46:05 +08:00
38fca01189
artiq_ddb_template: add su-servo support ( #1343 )
2019-09-11 15:52:25 +08:00
991c686d72
kasli_generic,eem: print RTIO channels in hex like artiq_ddb_template
2019-09-11 15:51:53 +08:00
f4dd7e5e29
kasli_tester: init urukul channel before calibrating
...
Otherwise the DDS is not initialized and with a cold system it fails to
find IO_UPDATE edges.
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-09-11 07:16:35 +00:00
7492a59f6d
kasli_generic: add SUServo support ( #1343 )
2019-09-11 11:12:48 +08:00
David Nadlinger
6d6f66338b
runtime: Update core config panic_reset command suggestion message
2019-09-10 19:31:19 +01:00
Charles Baynham
ddd34e5a9c
influx_schedule: log repo_rev along with other info
...
Signed-off-by: Charles Baynham <charles.baynham@npl.co.uk>
2019-09-10 13:46:28 +02:00
98caaebade
consistent use of 'class name' terminology to select a class within an experiment file. Closes #1348
2019-09-09 15:16:33 +08:00
21021beb08
kasli: remove opticlock (moved to kasli_generic)
2019-09-09 15:03:10 +08:00
436662be52
ddb_template: add Novogorny support
2019-09-09 15:00:45 +08:00
69c2acd9d7
ddb_template: sampler cnv is ttl not spi
2019-09-09 14:57:42 +08:00
cfb5ef5548
kasli_generic: add Novogorny support
2019-09-09 14:54:34 +08:00
0b9168994f
Revert "dashboard: Sort TTL moninj channels by name"
...
This reverts commit b3db3ea6fcCloses #1288
2019-09-06 11:17:10 +08:00
Charles Baynham
d31f30a436
influxdb_schedule: fix typo in parameter name
2019-09-05 17:42:56 +02:00
Charles Baynham
7ac8feea19
influxdb_schedule: Handle all exceptions
2019-09-05 17:42:56 +02:00
1fb317778a
eem/grabber: allow third EEM to be specified
2019-08-29 18:58:12 +08:00
90e8e074cd
firmware: turn errors into &str for remote_i2c as well
...
should resolve breakage on a few targets/variants introduced by PR #1351
2019-08-29 09:05:47 +08:00
71b3c66af9
firmware: conditionally compile has_si5324
...
avoids unused warnings where this module is not used.
2019-08-29 09:04:54 +08:00
959679d8b7
wrpll: add I2CMasterMachine
2019-08-27 18:02:05 +08:00
c03c35f375
Revert "compiler: armv7-unknown-linux-gnueabihf -> armv7-linux-gnueabihf"
...
rustc insists on -unknown.
This reverts commit cf47fa44d8
2019-08-26 11:23:00 +08:00
cf47fa44d8
compiler: armv7-unknown-linux-gnueabihf -> armv7-linux-gnueabihf
2019-08-26 11:12:49 +08:00
98cd9a539c
compiler: support Cortex A9 target
2019-08-26 10:46:22 +08:00
afe162ceca
firmware: don't unwrap() but propagate pca9548 errors
2019-08-17 09:15:26 +08:00
a8aabd3815
firwmare: turn i2c errors into &str
2019-08-17 09:15:26 +08:00
8fc5ce902f
firmware: let kasli obtain default hardware_addr from i2c_eeprom
2019-08-17 09:15:26 +08:00
d666f3d573
firmware: factor out mod pca9548 from si5324
...
orepares for further i2c devices.
2019-08-17 09:15:26 +08:00
1fd2322662
wrpll/thls: implement global writeback
2019-08-15 23:16:17 +08:00
24082b687e
wrpll/filters: clean up and make compatible with thls
2019-08-15 17:58:22 +08:00
9331fafab0
wrpll/filters: new code from Weida
2019-08-15 17:24:40 +08:00
5c3974c265
wrpll/thls: fix opcode decoding
2019-08-15 17:12:48 +08:00
19620948bf
wrpll/thls: implement signed numbers
2019-08-15 17:04:17 +08:00
efc43142a6
wrpll/thls: implement min/max
2019-08-15 16:42:59 +08:00
44969b03ad
wrpll/thls: rework instruction decoding
2019-08-15 15:55:13 +08:00
2776c5b16b
wrpll/thls: support mulshift
2019-08-15 15:07:13 +08:00
e9b78b62db
kasli_tester/zotino: always alternate voltage sign
...
Before the voltages on a second Zotino would start 2.1, 1.9, 2.2, 1.8
..., 3.6, 0.4 and overlap with the voltages on the first.
Now the voltages are 2.1, -2.1, 2.2, -2.2, ..., 3.6, -3.6 which allows
quick identification of card/channel and easy prediction when deploying.
2019-08-06 17:38:55 +02:00
f861459ace
wrpll: add filter algorithms (WIP)
2019-08-02 13:23:16 +08:00
David Nadlinger
99e490f9ff
coredevice/suservo: Slightly reword get_adc[_mu]() docstring for clarity
...
This hopefully suggests a bit better that the value is the last one
fetched by the servo (i.e. needs the servo active to update), rather
than somehow requesting a new sample to be taken.
2019-07-30 12:22:08 +01:00
3f0657f2a8
artiq_influxdb_schedule: add schedule logger
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-07-26 14:47:18 +02:00
7a5dcbe60e
wrpll/thls: support processor start/stop
2019-07-24 18:51:33 +08:00
b8870997d0
doc: clarify TTL direction control with buffered cards
2019-07-24 10:04:45 +08:00
623446f82c
wrpll/thls: simple simulation demo
2019-07-20 18:50:57 +08:00
831b3514d3
wrpll/thls: stop at return statement
2019-07-19 16:27:29 +08:00
David Nadlinger
280915d54f
coredevice/suservo: Adjust T_CYCLE to match gateware
...
See GitHub #1338 .
2019-07-17 00:20:22 +01:00
34222b3f38
wrpll: encode thls program
2019-07-09 17:56:14 +08:00
5f461d08cd
wrpll: add simple thls compiler
2019-07-09 16:07:31 +08:00
f7e10759dc
suservo: note requirement to stop servo when accessing state
...
As already mentioned in the gateware.
One alternative would be to detect address collisions and
stall the read for one cycle.
Note that there will in general not be a consistent view of the servo
state unless the servo is stopped.
close #1337
2019-07-08 18:37:42 +02:00
e4fff390a8
si590 -> si549
...
Had mistaken the part numbers.
2019-07-07 09:39:55 +08:00
dceb5ae501
wrpll: Si590 I2C mux, CDC
2019-07-05 23:42:37 +08:00
f8dba7ae35
rtio: use BlindTransfer from Migen
2019-07-05 18:46:18 +08:00
5a9bb0ecba
runtime: fix incorrect 'RTIO clock failed' report
2019-06-24 23:33:13 +08:00
David Nadlinger
8bf9640185
coredevice/suservo: Fix output IIR state width in docstring
2019-06-21 11:27:39 +02:00
David Nadlinger
34f48f57cc
coredevice/suservo: Fix {get,set}_y_mu() scaling
...
Previously, Channel.set_y(1) would set the output to -1 instead.
2019-06-21 11:27:39 +02:00
f6edceb23d
kasli_tester: cleanup/fix test skipping
2019-06-21 16:00:14 +08:00
whitequark
b8b9fa51bd
libdyld: accept objects with no rela relocations.
2019-06-17 06:43:34 +00:00
David Nadlinger
0353966ef7
gateware/suservo: Sign-extend data on RTIO read-back
...
See GitHub #1327 for original patch by Brad Bondurant.
2019-06-14 23:46:16 +01:00
David Nadlinger
720838a23e
gateware/suservo: Avoid magic number for activation delay width
...
Mostly for documentation purposes; 8 bits ought to be enough for
everyone.
2019-06-14 23:45:40 +01:00
53789ba9aa
tester: handle urukul switch differences
2019-06-14 10:54:00 +00:00
6655e567df
ddb_template: urukul fixes
...
* fix/add sw (ad9912 and ad9910)
* allow pll_n to be changed
2019-06-14 10:53:03 +00:00
53c778ae2d
runtime: fix previous commit
2019-06-14 15:53:01 +08:00
a947867887
runtime: support Kasli Si5324 bypass via rtio_clock=e
2019-06-14 15:48:05 +08:00
66a66b03b4
style
2019-06-14 15:29:16 +08:00
87ce24e867
runtime: refactor startup and RTIO clocking initialization
2019-06-14 15:26:30 +08:00
43e58c939c
sayma: drop MasterDAC
...
This seemed like a good idea then, but it introduces complexity, corner cases, and additional testing difficulties.
Now Sayma works fine with Kasli as a master, which is simpler.
2019-06-14 14:06:16 +08:00
b04e15741b
drop SI5324_SAYMA_REF
2019-06-14 14:03:48 +08:00
636b4cae5a
tester: urukul single-eem mode
2019-06-13 12:48:42 +00:00
591de0e579
ddb_template: support urukul single-eem mode
2019-06-13 12:19:12 +00:00
967d192cbe
ddb_template: wrong copy paste comma
2019-06-13 11:30:22 +00:00
8853cf8df9
dashboard: work around disappearing TTL/DDS panel bug. Closes #1307
2019-06-13 18:41:42 +08:00
1a898c423a
aqctl_corelog: filter log messages. Closes #1316
2019-06-13 18:17:52 +08:00
834d03527b
examples/dds_setter: fix RTIO underflow
2019-06-13 18:07:39 +08:00
e3c58d5872
remove outdated kc705 examples
2019-06-13 18:06:26 +08:00
74e4b01201
urukul: document consequences of incorrect CPLD clock settings
2019-06-11 11:12:12 +08:00
adf3df2bb5
suservo coredevice driver: mask ftw to avoid erroneous sign extension
2019-06-03 21:40:04 +02:00
bc2cfd77f5
metlino: add EEMs
2019-05-19 18:16:00 +08:00
cdef50c0dd
sayma_amc: Urukul v1.3
2019-05-19 16:54:38 +08:00
34c61db790
artiq_flash: fix Metlino support
2019-05-19 16:37:40 +08:00
88b6496c8c
artiq_flash: add Metlino support
2019-05-19 16:30:10 +08:00
9dcaae6395
metlino: use variant output directory
2019-05-19 16:24:51 +08:00
b4779969d0
metlino: work around vivado bug ( #1230 )
2019-05-19 11:27:27 +08:00
874542f33f
add Metlino support
2019-05-19 10:57:43 +08:00
hartytp
cfe1f56f73
suservo: add some more comments to the RTServoMem to clarify the RTIO interface ( #1323 )
2019-05-17 16:12:35 +01:00
David Nadlinger
84b91ee8bd
master/scheduler: Document Deleter semantics [nfc]
...
From looking at the code, it wasn't obvious to me that this is
supposed to handle multiple calls to delete(). This is the case,
however, when for instance Scheduler.delete()ing a run, which
will then also be deleted again from AnalyzeStage.
2019-05-14 22:37:16 +01:00
hartytp
c2b4f0cfe3
sync_struct: catch ConnectionErrors in _receive_cr ( #1319 )
2019-05-10 12:53:51 +01:00
hartytp
bbcd1db025
sync_struct: replace ConnectionError subclasses with ConnectionError ( #1318 )
2019-05-10 12:48:12 +01:00
hartytp
30fe624fe5
sync_struct: flake8 [nfc] ( #1317 )
2019-05-10 12:42:06 +01:00
1a3d71760d
consolidate kasli example folders
2019-05-10 12:17:38 +08:00
f551491a84
remove sayma_masterdac example
2019-05-10 12:13:07 +08:00
72f7f8386f
remove old Kasli device databases ( #1289 )
2019-05-10 12:11:42 +08:00
86f462f40e
artiq_ddb_template: add edge counter support
2019-05-09 17:20:13 +08:00
fda3cb2482
kasli_generic: add edge counter support
2019-05-09 17:19:11 +08:00
ead9a42842
kasli: remove VLBAIMaster, VLBAISatellite variants
2019-05-08 15:58:25 +00:00
0c9b810501
kasli: remove PTB/PTB2/LUH/HUB variants
...
see sinara-systems and nix-scripts repos
2019-05-08 15:51:18 +00:00
1d2cc60e0d
kasli_generic: support ext_ref
2019-05-08 15:51:18 +00:00
948ea396c0
remove old buildbot kc705 device-db
2019-05-07 17:28:06 +08:00
3209197b0b
artiq_flash: do not needlessly look for artifacts
2019-05-07 17:20:13 +08:00
a1c97ec4dd
kasli_tester: support selection of TTL output to use as stimulus
2019-05-07 16:58:00 +08:00
4cc9bd33ce
test: only test_rpc_timing actually requires ARTIQ_LOW_LATENCY
2019-04-24 11:22:07 +08:00
bb39eedf5b
fix previous commit
2019-04-20 10:44:07 +08:00
93f4f31f45
devices.ctlmgr -> master.ctlmgr
2019-04-20 00:25:44 +08:00
56033b60a7
move thorlabs_tcube out of tree ( #887 )
2019-04-20 00:09:58 +08:00
eaec519ac8
move lda out of tree ( #887 )
2019-04-19 23:43:14 +08:00
d4781e9a8a
aqctl_corelog: add simulation mode
2019-04-19 23:42:37 +08:00
62e9b2d85e
move novatech409b out of tree ( #887 )
2019-04-19 21:56:16 +08:00
4c1fb0c2a1
move korad_ka3005p out of tree ( #887 )
2019-04-19 19:47:41 +08:00
73d6078883
use IP instead of hostname for kc705-1
...
Makes it easier to run tests in the Windows VM
2019-04-18 22:59:32 +08:00
David Nadlinger
4d215cf541
firmware: Add Si5324 config for 125 MHz ext ref
...
PLL divider settings as suggested by DSPLLsim 5.1.
2019-04-15 22:22:19 +01:00
David Nadlinger
dc7a642b26
test/lit: Make abs() integration test slightly more interesting
...
I had accidentally not included this local diff in the PR that was
merged as commit cdaf554736
2019-04-14 04:12:40 +01:00
David Nadlinger
cdaf554736
compiler: Implement abs() for scalars
...
GitHub: Fixes #1303 .
2019-04-13 13:39:16 +08:00
97b7ed557b
sayma_amc: do not use SFP0 (now used for Ethernet)
2019-04-12 18:47:18 +08:00
David Nadlinger
cd7a5a3683
firmware: Fix kernel RPC handling of zero-size values (e.g. empty arrays)
2019-03-31 18:33:44 +01:00
David Nadlinger
b4ddf4c86b
firmware: Make "unexpected reply from kernel CPU" log messages unique
...
This makes it easier to localize issues based on the log output.
2019-03-31 18:31:56 +01:00
David Nadlinger
236b30ac5f
coredevice: Add test for recent kernel RPC fixes
...
This covers all three (de)serialisation fixes.
2019-03-31 18:25:56 +01:00
David Nadlinger
88fd5c8440
compiler: Fix crash in escape analysis for assigning string literals
2019-03-31 17:10:27 +01:00
David Nadlinger
990e0b7dd9
compiler: Fix comparison of tuples of lists
2019-03-31 17:10:27 +01:00
David Nadlinger
baf102dbb2
compiler: Fix comparison of nested lists
2019-03-31 17:10:27 +01:00
David Nadlinger
8e225433a5
firmware: Fix kernel RPC strings size (memory corruption)
...
Test case to follow.
2019-03-31 17:10:27 +01:00
David Nadlinger
b8ff627be9
firmware: Fix kernel RPC tuple size calculation (memory corruption)
...
Test case to follow.
2019-03-31 17:10:27 +01:00
David Nadlinger
fc95183e04
coredevice: Fix host-side serialization of (nested) lists
...
Test case to follow.
2019-03-31 17:10:27 +01:00
David Nadlinger
f9af058b96
compiler: Quote tuples as TTuple values
...
Previously, they would end up being TInstances,
rendering them useless.
2019-03-31 23:40:21 +08:00
3634cfac86
typo
2019-03-31 22:27:07 +08:00
4580f3dac8
test/lit: support overriding libartiq_support.so
2019-03-31 22:26:09 +08:00
4499ef1748
kasli: only add moninj core if there are probes to monitor
2019-03-24 14:09:52 +08:00
5d31cf2268
sayma_rtm2: si5324_clkout -> cdr_clk_clean
2019-03-23 13:48:36 +08:00
560849e693
sayma_amc: add DRTIO transceiver on rtm_amc_link for v2 hardware
2019-03-23 13:41:22 +08:00
bbb8c00518
sayma_amc: default to satellite variant
2019-03-23 13:37:55 +08:00
18fbe0b081
sayma_rtm_drtio: support v2 hardware
2019-03-23 13:31:28 +08:00
c7205ad82f
sayma_rtm: preliminary v2 support
2019-03-23 12:37:03 +08:00
d07c6fcfea
ad9910: handle unprogrammed EEPROM and numpy corner cases
2019-03-22 14:28:47 +08:00
7cdcaf0d00
tests: fix coredevice tests after implementing scheduler defaults
2019-03-22 07:27:55 +08:00
33b28f6e56
sayma_amc: add placeholder code to use DDMTD signals on v2 hardware
2019-03-21 17:37:22 +08:00
2ec5a58c59
sayma_amc: si5324_clkout -> cdr_clk_clean
2019-03-21 14:09:33 +08:00
af785b9a9c
artiq_compile: fix after adding scheduler defaults
...
Closes #1290
2019-03-21 09:56:19 +08:00
8d2c1be44f
artiq_flash: ignore rtm_gateware on Sayma for variant autodetection
2019-03-17 15:57:50 +08:00
c2622297bd
urukul: use board_data instead of user_data to store calibration in EEPROM
2019-03-15 17:57:35 +08:00
a01425bc9c
kasli_tester: do not attempt to synchronize AD9912 Urukul
2019-03-15 17:13:29 +08:00
fcf8828cb6
fix tests, artiq_run after implementing scheduler defaults ( #1290 )
2019-03-13 17:20:30 +01:00
5e7c83c9cf
artiq_ddb_template: enable Urukul synchronization from EEPROM
2019-03-13 15:42:51 +08:00
e504262b67
kasli_tester: calibrate Urukul synchronization and write to EEPROM
2019-03-13 15:36:05 +08:00
346299e7f8
kasli_tester: enable EEPROM for Urukul synchronization
2019-03-13 15:35:23 +08:00
04e0c23e78
ad9910: support reading synchronization values from EEPROM
2019-03-13 15:34:47 +08:00
852048dce4
artiq_ddb_template: create Urukul EEPROM device
2019-03-13 15:34:23 +08:00
964a349a19
add Kasli I2C driver
2019-03-13 15:33:50 +08:00
c56c3e5588
dashboard: add support for experiment pipeline/priority/flush defaults
2019-03-12 10:54:15 +01:00
8659c769cb
master/language: add methods to set experiment pipeline/priority/flush defaults
2019-03-12 10:54:15 +01:00
b2177eff81
kasli_tester: run test_i2c_switch
2019-03-11 21:06:28 +08:00
227c729f56
fix permissions
2019-03-11 20:43:28 +08:00
David Nadlinger
b3db3ea6fc
dashboard: Sort TTL moninj channels by name
...
With growing system complexity, the moninj channel index is
no longer a very intuitive ordering for typical end users.
2019-03-11 03:30:14 +01:00
David Nadlinger
5fd92a6175
gui: Fix crash when quickly opening/closing applets
...
Quickly closing/reopening applets (e.g. quickly clicking the checkbox
on an entire folder of applets) would previously lead to an occasional
KeyError on the self.dock_to_item access in on_dock_closed, as close()
would be invoked more than once.
The geometry/checked state handling can potentially be cleaned up
further, but at least this avoid the crash.
2019-03-10 20:57:10 +00:00
e47ba4b35e
kasli_generic: fix identifier string
2019-03-08 19:57:20 +08:00
b219f8b5c7
artiq_flash: autodetect variant
2019-03-08 19:47:24 +08:00
fc9d4c7bdc
artiq_flash: fix sayma master detection
2019-03-08 19:36:35 +08:00
25bcebd1f6
artiq_flash: not all boards are development boards
2019-03-08 19:35:20 +08:00
ed2d8dfa7a
artiq_flash: resolve openocd symbolic links
...
On NixOS, openocd may be a symlink in /run/current-system/sw/bin when installed system-wide.
2019-03-08 12:43:06 +08:00
0d05d4b813
artiq_client: python 3.7 compatibility
2019-02-26 17:09:38 +08:00
ec966de007
thorlabs_tcube: cleanup
2019-02-26 16:50:19 +08:00
62c7f75a9e
sayma_amc: support hardware revisions
2019-02-25 23:49:45 +08:00
d45249197c
siphaser: improve ultrascale clock routing
2019-02-25 23:00:01 +08:00
de3992bbdd
kasli: remove HUST variants (supported by kasli_generic)
2019-02-23 15:44:17 +08:00
791f830ef6
kasli_generic: support DRTIO
2019-02-23 15:41:05 +08:00
d39338d59f
artiq_ddb_template: fix --satellite
2019-02-23 15:27:18 +08:00
d79a6ee41c
artiq_ddb_template: fix pll_vco indentation
2019-02-22 23:50:30 +08:00
62985fbd29
binaries -> board-support
2019-02-22 23:18:01 +08:00
1c35c051a5
kasli: remove variants supported by generic builder
2019-02-22 23:08:49 +08:00
05b128469f
artiq_ddb_template: support setting Urukul pll_vco
2019-02-22 22:59:20 +08:00
cd60803f21
device_ddb_template: add Sampler, Zotino, Grabber and SFP LED support
2019-02-22 20:07:15 +08:00
269f0a4d6f
artiq_ddb_template: add Urukul support
2019-02-22 19:33:27 +08:00
8049c52d06
frontend: add artiq_ddb_template (WIP, TTL only)
2019-02-22 17:19:48 +08:00
8edc2318ab
style
2019-02-22 17:19:20 +08:00
aee8965897
ad9910: add ram conversion tooling and unittests
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-02-21 15:59:52 +00:00
ec6588174b
ad9910: add ram operation unittests
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-02-21 15:14:32 +00:00
b57cad77ad
ad9910: make ram read work for short segments
...
also cleanup and style
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-02-21 14:47:58 +00:00
596d3e20d7
dashboard,browser: do not call get_user_config_dir() in argparse
...
This caused two problems when building the docs:
* the path printed in the docs depends on the machine where they are built
* it pollutes ~/.config, and also breaks Nix builds
2019-02-19 15:43:04 +08:00
40a0cf806d
support overriding versioneer
2019-02-17 14:49:52 +08:00
6ad2e13515
kasli: add generic builder (WIP)
2019-02-12 19:18:09 +08:00
2104a93f78
build_soc: allow overriding SoC class name
2019-02-12 18:33:52 +08:00
ff4e4f15ed
kasli: expose base SoC classes
2019-02-12 18:33:27 +08:00
whitequark
0a84dd38c1
Add missing test from d6eb2b02.
2019-02-10 07:25:53 +00:00
David Nadlinger
01c3000ef3
master: Print offending key on HDF5 dataset type error
...
This helps debugging the cause of TypeErrors arising from types
not handled by the HDF5 serializer, as the backtrace doesn't
otherwise include any useful information.
2019-02-09 20:50:38 +00:00
David Nadlinger
56b2e0c262
artiq_influxdb: Support append() in dataset _Mock
...
This went undetected as append mods were not actually in use
in any part of the codebase previously.
2019-02-09 20:50:38 +00:00
David Nadlinger
bf84226c7d
language: Support appending to datasets
2019-02-09 20:50:38 +00:00
David Nadlinger
820326960e
test: Add basic experiment dataset interface tests
2019-02-09 20:50:38 +00:00
2de1eaa521
dashboard: reconnect to core moninj
...
* handle disconnects like core device address changes and do a
disconnect/connect iteration
* after connection failure wait 10 seconds and try again
* this addresses the slight regression from release-2
to release-3 where the moninj protocol was made stateful
(#838 and #1125 )
* it would be much better to fix smoltcp/runtime to no loose the
connection under pressure (#1125 )
* the crashes reported in #838 look more like a race condition
* master disconnects still require dashboard restarts
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-02-08 23:52:16 +08:00
1cfd26dc2e
kasli: add UNSW variant
2019-02-08 17:51:51 +08:00
3e8fe3f29d
suservo: fix permissions
2019-02-08 14:54:02 +08:00
David Nadlinger
ef934ad958
Add test/release notes for command-less controllers
...
See eaa1b44b00
2019-02-07 21:51:15 +00:00
eaa1b44b00
ctlmgr: ignore controllers without a "command" field
...
Allow controllers to be specified without a "command" field. The user takes
responsibility for ensuring the controller is running: the controller manager
does not attempt to ping the controller. This is useful when one has a common
controller shared between several masters.
2019-02-07 21:50:29 +00:00
hartytp
0ebff04ad7
SUServo: apply bit masks to servo memory writes to prevent overflows
...
Signed-off-by: TPH <thomas.harty@physics.ox.ac.uk>
2019-02-07 17:04:11 +01:00
hartytp
f6142816b8
Revert "SUServo: remove references to non-existent a0 parameter" ( #1270 )
...
This reverts commit f3aab2b89156bbc1b12f847093a87a8933293df2.
Signed-off-by: TPH <thomas.harty@physics.ox.ac.uk>
2019-02-07 15:57:43 +00:00
hartytp
fe63c9b366
SUServo: remove references to non-existent a0 parameter ( #1268 )
...
Signed-off-by: Thomas Harty <thomas.harty@physics.ox.ac.uk>
2019-02-07 15:29:32 +00:00
hartytp
df6c1fca2c
SUServo: flake8 [NFC] ( #1267 )
...
Signed-off-by: Thomas Harty <thomas.harty@physics.ox.ac.uk>
2019-02-07 15:13:44 +00:00
hartytp
87e85bcc14
suservo: fix coefficient data writing
...
Signed-off-by: Thomas Harty <thomas.harty@physics.ox.ac.uk>
2019-02-07 14:47:11 +01:00
whitequark
d6eb2b023a
compiler: monomorphize casts first, but more carefully.
...
This reverts 425cd7851Fixes #1252 .
2019-02-07 06:24:32 +00:00
b56c7cec1e
kasli: use 100MHz RTIO and 800MHz Urukul frequencies on Berkeley target
...
Urukul sync is not reliable at 125/1000
2019-02-05 11:24:45 +08:00
5a7460a38e
kasli: add sync delays to device_db_berkeley
2019-02-01 22:14:03 +08:00
ea431b6982
sayma_rtm: use 150MHz RTIO freq for DDMTD
2019-01-31 20:43:44 +08:00
ec230d6560
sayma: move SYSREF DDMTD to the RTM
...
Put RTM Si5324 into bypass mode before running.
Needs rework to cut RTM Si5324 reset trace.
Needs rework to fix LVDS termination on RTM R310/R313 and R314/R315.
Needs uFL jumper cables between RTM "REF LO DIAG" and "CRD AUX CLKIN" (sic).
2019-01-31 20:39:33 +08:00
8119000982
sayma_rtm_drtio: use Si5324 soft reset
...
Needs easy board rework to cut trace at pin 1 of Si5324.
The Si5324 contains an internal pull-up on that pin.
Allows using Si5324 + HMC7043 chips at the same time.
Allows the Si5324 bypass hack for DDMTD experiments on the RTM.
2019-01-31 19:43:54 +08:00
82106dcd95
si5324: add bypass function
2019-01-31 19:38:55 +08:00
8bbd4207d8
si5324: use consistent bitmask
2019-01-31 19:35:56 +08:00
d3c608aaec
jesd204sync: reset and check lock status of DDMTD helper PLL in firmware
2019-01-31 15:11:16 +08:00
fa3b40141d
hmc830_7043: document sayma clock muxes
2019-01-31 15:10:11 +08:00
ec8560911f
siphaser: bugfixes
...
* Fix integer overflow in degree computation
* Add some phase slips after the first transition to get out of the jitter zone and avoid intermittent short windows
2019-01-30 16:56:38 +08:00
c591009220
sayma: report TSC phase of SYSREF (TSC LSBs on SYSREF rising edge) in SYSREF sampler
...
Better visibility, better diagnostics, allows some changing of SYSREF frequency while keeping the same gateware.
2019-01-29 23:30:01 +08:00
9d0d02a561
jesd204sync: increase tolerance for coarse->final target in calibrate_sysref_target
...
There is plenty of slack (it only needs to meet timing at the RTIO frequency).
2019-01-29 16:48:55 +08:00
ed6aa29897
jesd204sync: print more information on test_slip_ddmtd error
2019-01-29 16:47:29 +08:00
2e8decbce3
kasli_sawgmaster: generate a HMC830 clock with Urukul
2019-01-29 15:06:45 +08:00
9ae57fd51e
sayma: pass rtio_clk_freq to DDMTD core
2019-01-29 15:06:45 +08:00
90c9fa446f
test: add array transfer test
...
200 kB/s, more than a factor of 10 slower than the bare string transfer
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-01-28 14:30:44 +00:00
7a5d28b73d
jesd204sync: test SYSREF period
2019-01-28 19:11:38 +08:00
1a42e23fb4
jesd204sync: print DDMTD SYSREF final alignment delta
2019-01-28 18:39:16 +08:00
eebff6d77f
jesd204sync: fix max_phase_deviation
2019-01-28 18:38:18 +08:00
b9e3fab49c
jesd204sync: improve messaging
2019-01-28 18:37:46 +08:00
145f08f3fe
jesd204sync: update SYSREF S/H limit deviation tolerance
...
Follows the increased DDMTD resolution.
2019-01-28 18:21:31 +08:00
ba21dc8498
jesd204sync: improve messaging
2019-01-28 18:08:20 +08:00
3acee87df2
firmware: improve DDMTD resolution using dithering/averaging
2019-01-28 16:04:04 +08:00
cfe66549ff
jesd204sync: cleanup DDMTD averaging code
2019-01-28 14:14:50 +08:00
2b0d63db23
hmc830_7043: support 125MHz RTIO
2019-01-28 13:44:08 +08:00
bdd4e52a53
ad9154: support 125MHz RTIO
2019-01-28 13:43:52 +08:00
47312e55d3
sayma: set RTIO_FREQUENCY in MasterDAC
2019-01-28 13:43:28 +08:00
443d6d8688
sayma_amc: pass RTIO clock frequency to SiPhaser
2019-01-28 09:49:03 +08:00
3b6f47886e
firmware: print more info on DDMTD stability error
2019-01-27 23:06:11 +08:00
74fdd04622
firmware: test DDMTD stability
2019-01-27 20:39:12 +08:00
81b0046f98
ddmtd: add deglitchers
2019-01-27 20:38:41 +08:00
8254560577
sayma: properly determine SYSREF coarse calibration target
2019-01-27 16:00:36 +08:00
214394e3b0
sayma: reimplement DAC SYSREF autocalibration
2019-01-27 15:28:39 +08:00
fdbf1cc2b2
sayma: rework DAC SYSREF margin validation
...
Previous code did not work when delay range was not enough for two rotations.
This removes autocalibration, to be done later. Uses hardcoded value for now.
2019-01-27 14:17:54 +08:00
7e5c062c2c
firmware: bypass channel divider for HMC7043 DCLK
2019-01-27 11:49:34 +08:00
f73ffe44f9
firmware: implement DDMTD-based SYSREF/RTIO alignment (draft)
...
Mostly works and usually gets the DAC synchronized at 2.4GHz with Urukul across DRTIO.
Needs cleanup and optimization/characterization.
2019-01-27 09:51:24 +08:00
8632b553d2
ddmtd: use IOB register to sample input
2019-01-27 09:50:02 +08:00
d1ef036948
kasli_sawgmaster: initialize SAWG phase according to RTIO TSC
2019-01-27 09:49:31 +08:00
9966e789fc
sayma: simplify Ultrascale LVDS T false path
...
Recommended by Xilinx.
2019-01-25 23:40:48 +08:00
359fb1f207
sayma: fix DDMTD STA
2019-01-25 23:39:19 +08:00
cb04230f86
sayma: SYSREF setup/hold validation demonstration
...
This also removes the standalone target as the ISERDES used
for setup/hold check requires the fine RTIO clock, which in turn
requires a DRTIO transceiver due to the Ultrascale TPWS bug.
2019-01-25 16:58:58 +08:00
3356717316
sayma: DDMTD SYSREF measurement demonstration
2019-01-25 16:00:31 +08:00
4941fb3300
sayma: 2.4GHz DAC clocking (4X interpolation)
...
* gets another clock divider out of the way
* gets one cycle within range of the HMC7043 analog delay alone
* SYSREF/RTIO alignment removed, to be replaced with DDMTD-based scheme
2019-01-25 13:47:04 +08:00
cc9420d2c8
hmc7043: fix divider programming
2019-01-25 11:48:50 +08:00
8c5a502591
ad53xx: ignore F3 (reserved)
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-01-24 15:50:46 +01:00
bbac92442f
sayma: check hmc7043 slip period
2019-01-24 20:13:43 +08:00
a92cc91dcb
kasli_sawgmaster: correctly tune DDS and SAWG
2019-01-24 19:37:14 +08:00
f8b39b0b9a
sayma: enable 2X DAC interpolation
...
Seems to work just fine and gets one clock divider out of the way.
2019-01-24 18:28:01 +08:00
07b5b0d36d
kasli: adapt Master target to new hardware
2019-01-24 18:27:15 +08:00
154269b77a
kasli: fix HUST satellite Urukul
2019-01-23 17:59:43 +08:00
3b5fd3ac11
kasli_tester: fix grabber test
2019-01-23 17:59:25 +08:00
330c5610e9
ad9912: fix imports
2019-01-23 17:59:08 +08:00
390f05f762
firmware: use smoltcp release
2019-01-23 16:15:05 +08:00
d7e6f104d2
kasli: add HUST variants
2019-01-23 14:11:51 +08:00
81f2b2c864
kasli: remove unpopulated Tester EEMs
...
* matches hardware and avoids issues with programs that process the DDB (e.g. kasli_tester)
* shortens compilation times
2019-01-23 12:14:44 +08:00
b692981c8e
ad9910: add note about red front panel led
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-01-22 12:49:42 +01:00
a0eba5b09b
satman: support Grabber
2019-01-22 19:36:13 +08:00
2e3555de85
firmware: fix compilation error with more than 1 Grabber
2019-01-22 19:35:46 +08:00
9ee5fea88d
kasli: support optional SATA port for DRTIO
2019-01-22 18:06:48 +08:00
91e375ce6a
ad9910: don't reset the input divide-by-two
...
suspected of causing weird PLL lock timout errors
https://freenode.irclog.whitequark.org/m-labs/2019-01-22#1548148750-1548143221 ;
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-01-22 09:37:20 +00:00
81ff3d4b29
ad9912: add some slack after init
2019-01-21 17:10:58 +00:00
a9678dd9f2
test_frontends: always skip GUI programs
...
The "import PyQt5" hack breaks on nix/hydra.
2019-01-21 23:41:07 +08:00
84f7d006e8
ad9910: add precision about tune_io_update_delay/tune_sync_delay order
2019-01-21 19:40:55 +08:00
30051133b7
urukul: fix typos
2019-01-21 19:40:55 +08:00
30b2f54baa
kasli_tester: skip Zotino test when no Zotino is present
2019-01-21 18:11:41 +08:00
bff8c8cb05
kasli: add Berkeley variant
2019-01-21 17:44:17 +08:00
a987d2b2e5
kasli_tester: skip Grabber test when no Grabber is present
2019-01-21 17:43:48 +08:00
David Nadlinger
4ba4e9c540
test_scheduler: Test for hang when exiting with running experiments
...
The respective code path in artiq.master.scheduler._mk_worker_method
wasn't previously covered.
2019-01-20 19:45:50 +00:00
David Nadlinger
0dab7ecd73
master: Include RID in worker exception messages
...
This helps when debugging unexpected shutdown problems
after the fact.
2019-01-20 19:45:50 +00:00
David Nadlinger
e24e893303
master/scheduler: Fix misleading indentation [nfc]
2019-01-20 19:45:47 +00:00
David Nadlinger
e165a9a352
sync_struct: Factor action strings out into enum and document them [nfc]
2019-01-19 20:19:17 +00:00
David Nadlinger
c213ab13ba
sync_struct: Notifier.{read -> raw_view}, factor out common dict update code [nfc]
2019-01-19 20:19:17 +00:00
David Nadlinger
bd71852427
sync_struct: Tweak variable name to avoid confusion with init mod action [nfc]
2019-01-19 20:19:17 +00:00
David Nadlinger
90c144a685
test_pc_rpc: Remove leftover debug print [nfc]
...
This tidies up the test suite output, and we have verbose asserts
to show further information on breakage, should it occur.
2019-01-19 20:18:33 +00:00
a2ff2cc173
sayma_amc: use more selective IOBUFDS false path
2019-01-19 11:47:50 +08:00
40187d1957
ad9910: support configurable refclk divider and pll bypass
...
for #1248
* also always keep refclk input divider (by two) reset
2019-01-18 12:23:53 +00:00
385916a9a4
ad9912: support configurable clk_div
2019-01-18 12:16:08 +00:00
2bea5e3d58
urukul: support configurable refclk divider
...
for #1248
2019-01-18 12:09:32 +00:00
689714965b
monkey_patches: disable for Python >= 3.6.7
...
3.6 >=7 are fixed
3.7.0 is incompatible with the monkey patches and they do more harm than good
3.7 >=1 are fixed
2019-01-15 20:29:20 +08:00
David Nadlinger
1c71ae636a
examples: Add edge counters to kasli_tester variant
...
This enables test_edge_counter on the CI system.
2019-01-15 10:55:07 +00:00
David Nadlinger
67a6882e91
examples: Fix kasli_tester device_db offset comments
2019-01-15 10:55:07 +00:00
David Nadlinger
a565f77538
Add gateware input event counter
2019-01-15 10:55:07 +00:00
4cb9f77fd8
sayma_amc: fix Master timing constraints
2019-01-13 13:53:07 +08:00
David Nadlinger
6c52359e59
coredevice: Add _mu suffix to AD991x ref_time arguments
...
GitHub: Fixes #1243 .
2019-01-12 17:34:35 +00:00
David Nadlinger
24b1b9a480
Add smoke test for frontend commands
...
This ensures that at least --help works for all the commands,
preventing regressions like that in f3323a35d5
2019-01-12 13:50:53 +00:00
whitequark
425cd7851e
compiler: first monomorphize ints, then casts.
...
Fixes #1242 .
2019-01-12 13:40:12 +00:00
whitequark
49682d0159
Improve Python 3.7 compatibility.
...
async is now a full (non-contextual) keyword.
There are two more instances:
- artiq/frontend/artiq_client.py
- artiq/devices/thorlabs_tcube/driver.py
It is not immediately clear how to fix those, so they are left for
later work.
2019-01-12 13:17:59 +00:00
David Nadlinger
f3323a35d5
artiq_influxdb: Unbreak after verbosity_args rename
...
This fixes commit f2c1d32e54
2019-01-12 12:02:22 +00:00
David Nadlinger
48fc175a6b
coredevice.ttl: More imperative mood in docstrings [nfc]
...
This follows Python conventions (PEP257) and unifies the style with
other comments.
2019-01-12 12:01:55 +00:00
Drew
f2c1d32e54
frontend: add --version flag to cmd line args ( #1181 )
2019-01-12 09:47:47 +08:00
David Nadlinger
3e84ec2bf1
coredevice.ad9910: Fix phase tracking ref_time passing
...
This is difficult to test without hardware mocks or some
form of phase readback, but the symptom was that e.g.
`self.dds.set(…, ref_time=now_mu() - 1)` would fail
periodically, that is, whenever bit 32 of the timestamp
would be set (which would be turned into the sign bit).
This is a fairly sinister issue, and is probably a compiler
bug of some sort (either accepts-invalid or wrong type inference).
2019-01-12 00:47:38 +00:00
Drew
66861e6708
test_pc_rpc: fix equality bug ( #1188 ) ( #1239 )
...
Fixes bug from 5108ed8. Truth value of multi-element numpy array is
not defined. Completes #1186 and fixes/amends #1188 .
Signed-off-by: Drew Risinger <drewrisinger@users.noreply.github.com>
2019-01-11 10:15:44 +08:00
101671fbbf
core_analyzer: support uniform VCD time intervals
...
close #1236
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-01-10 19:35:09 +01:00
Drew
99a0f61b35
artiq_client: remove custom input validation for built-in argparse ( #1185 )
2019-01-10 12:58:11 +08:00
Drew
721c6f3bcc
pc_rpc: fix handling of type annotations
2019-01-10 12:13:22 +08:00
088530604e
test_ad9910: relax tests
...
* tune_sync_delay: the opposite IO_UPDATE to SYNC_CLK alignment may not be perfectly
mis-aligned
* set_mu_speed: seems to be slower on the buildbot
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-01-09 17:27:42 +00:00
19748fe495
ad9910: fix RTIO fine timestamp nudging
...
Previously the TSC was truncated to an even coarse RTIO periods before doing
the setting SPI xfer. Afterwards the the IO update pulse would introduce
at least one but less than two RTIO cycles. Ultimately the RTIO TSC was
truncated again to even. If the SPI xfer takes an odd number of RTIO
periods, then a subsequent xfer would collide.
close #1229
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-01-09 17:22:57 +00:00
b25ab1fc88
ad9910: add more slack in tune_sync_delay
...
close #1235
Signed-off-by: Robert Jördens <rj@quartiq.de>
2019-01-09 16:07:31 +00:00
9b213b17af
sayma_amc: forward RTM UART in Master variant as well
2019-01-09 18:57:57 +08:00
c7b18952b8
sayma_amc: work around Ultrascale LVDS Toutbuf_delay_td_pad
2019-01-09 13:47:08 +08:00
62599c5f91
firmware: use consistent terminology
2019-01-09 13:46:18 +08:00
Drew
b3b0b6f0a5
artiq_influxdb: clarify argparse groups ( #1212 )
...
Make names of argparse group variables relate to what they're doing.
Meets Flake8.
Signed-off-by: Drew Risinger <drewrisinger@users.noreply.github.com>
2019-01-09 11:40:55 +08:00
David Nadlinger
101ed5d534
examples: Fix DRTIO destination indices ( #1231 )
...
Using the default routing table, links numbers and destinations
are offset by 1, as destination 0 is local RTIO.
2019-01-09 11:40:15 +08:00
Drew
40370c4d45
Docs: fix build warnings ( #1234 )
...
* ad9910: finish CONT_RECIRCULATE -> CONT_RAMPUP
Found while building docs. Forgot to refactor strings.
Signed-off-by: Drew Risinger <drewrisinger@users.noreply.github.com>
* spi2: reformat update_xfer_duration_mu docstring
update_xfer_duration_mu docstring threw warning while building docs,
didn't use consistent indent in warning.
Signed-off-by: Drew Risinger <drewrisinger@users.noreply.github.com>
2019-01-09 11:39:23 +08:00
David Nadlinger
4fb434674d
coredevice: Fix ad9910 __all__ exports
2019-01-08 18:55:26 +00:00
887cb110a7
firmware: fix default DRTIO routing table
2019-01-08 20:46:53 +08:00
David Nadlinger
cadde970e1
urukul: Expand CPLD sync_sel explanation [nfc]
2019-01-08 02:37:58 +00:00
David Nadlinger
7bcdeb825b
ad9910: Add inverse FTW/ASF conversions
2019-01-08 02:18:14 +00:00
David Nadlinger
4d793d7149
ad9910: Truncate phase word to 16 bits
...
This avoids overflowing into the asf portion of the register.
2019-01-08 02:18:14 +00:00
332bd6090f
satman: wait for CPLL/QPLL lock after setting drtio_transceiver::stable_clkin
2019-01-07 17:09:19 +08:00
3217488824
add Sayma RTM DRTIO target
2019-01-07 00:13:47 +08:00
b5501aaf00
firmware: program I2C switch on Sayma RTM
2019-01-06 14:54:52 +08:00
66b3132c28
sayma_amc: fix RTIO TSC instantiation
2019-01-06 14:54:32 +08:00
6e43c41103
firmware: support building without SDRAM
2019-01-05 23:41:30 +08:00
cf9447ab77
rtio/cri: remove unneeded CSR management
2019-01-05 23:40:45 +08:00
2c3510497b
firmware: fix not(has_spiflash) build
2019-01-05 23:40:03 +08:00
2100a8b1f1
sayma_amc: more fighting with vivado timing analyzer
2019-01-05 12:25:30 +08:00
Drew Risinger
b58d59a9e7
pyon: fix grammar in module docstring.
...
Signed-off-by: Drew Risinger <drewrisinger@users.noreply.github.com>
2019-01-04 19:31:08 +00:00
a93fdb8c9d
drtio: disable all destinations in gateware at startup
...
Otherwise, kernels fail to get a RTIODestinationUnreachable exception when attempting
to reach a DRTIO destination that has never been up.
2019-01-04 23:42:12 +08:00
62d7c89c48
sayma_amc: use high-resolution TTL on SMAs ( #792 )
2019-01-03 20:50:38 +08:00
0972d61e81
ttl_serdes_ultrascale: use GTH clock domains
2019-01-03 20:50:04 +08:00
f007895fad
drtio/gth_ultrascale: fix rtiox clock domain
2019-01-03 20:49:38 +08:00
10ebf63c47
jesd204_tools: get the Vivado timing analyzer to behave
2019-01-03 20:22:35 +08:00
d6a3172a3e
update copyright year
2019-01-03 20:21:34 +08:00
4af8fd6a0d
ttl_serdes_ultrascale: fix Input
2019-01-03 20:14:54 +08:00
175f8b8ccc
drtio/gth_ultrascale: generate multiplied RTIO clock from BUFG_GT ( #792 )
2019-01-03 20:14:18 +08:00
77126ce5b3
kasli: use hwrev 1.1 by default for DRTIO examples
2019-01-02 23:04:20 +08:00
ab9ca0ee0a
kasli: use 150MHz for DRTIO by default (Sayma compatibility)
2019-01-02 23:03:57 +08:00
cc58318500
siphaser: autocalibrate skew using RX synchronizer
...
* removes the hardcoded, (poorly) manually determined skew value
* does not need si5324_clkout_fabric anymore (broken on Sayma RTM due to wrong IO voltage)
2019-01-02 22:29:27 +08:00
f5cda3689e
sayma_amc: enable DRTIO on master SATA connector for MasterDAC variant
2019-01-02 16:46:16 +08:00
Drew
d60b95f481
tdr.py: typo ( #1220 )
2018-12-18 18:47:09 +00:00
a7d4d3bda9
ad9910: CONT_RECIRCULATE -> CONT_RAMPUP
2018-12-17 13:25:00 +00:00
35bdf26f01
Merge branch 'ad9910-ram'
2018-12-17 21:16:44 +08:00
David Nadlinger
e608d6ffd3
coredevice, firmware: Add rtio_input_timestamped_data
...
Integration tests to follow as part of an RTIO counter phy that
makes use of this.
2018-12-15 00:35:04 +00:00
David Nadlinger
8e30c4574b
firmware: Treat timestamps consistently as signed [nfc]
...
This matches other functions and the ARTIQ Python side, but
isn't actually an ABI change.
2018-12-15 00:02:18 +00:00
38ce7ab8ff
sync_struct: handle TimeoutError as subscriber disconnection. Closes #1215
2018-12-13 06:58:54 +08:00
79eadb9465
ad9910: add RAM mode methods
...
* also refactor the CFR1 access into a method
c.f. #1154
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-12-11 14:54:16 +00:00
6df4ae934f
eem: name the servo submodule
...
This allows the migen namer to derive names for the ADC return clock
domain in the case of multiple SUServos
close #1201
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-12-11 11:36:40 +01:00
efd400b02c
ad9910: style [nfc]
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-12-11 11:36:25 +01:00
David Nadlinger
d4c393b2a8
firmware/ksupport: Update cfg(not(has_rtio)) stub signatures
...
This fixes up 8caea0e6d3
2018-12-11 01:22:48 +00:00
d90eb3ae88
ad9910: add read64()
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-12-07 21:27:00 +00:00
baf88050fd
urukul: expand attenuator HITL unittests
...
* read back with cleared backing state
* individual channel settings
* check backing state
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-12-07 21:06:12 +00:00
Kaifeng
cc143d5fec
kasli_tester: add support for windows platform. ( #1204 )
2018-12-05 14:06:45 +01:00
6aa341bc44
test_loopback_gate_timing: fix lat_offset
2018-12-02 20:52:32 +08:00
421834fa3e
compiler: document Target.little_endian
2018-12-02 19:07:18 +08:00
981a77834a
compiler: use default triple to determine data_layout for JIT
2018-12-02 18:52:13 +08:00
d931967e5c
fix previous commits
2018-12-02 18:32:03 +08:00
dd03fdfd1a
typo
2018-12-02 18:26:54 +08:00
8940009e1a
compiler: pass data_layout string to llvm.create_target_data before determining endianness
2018-12-02 18:26:19 +08:00
2e66788c6c
compiler: support little endian target when storing now
2018-12-02 17:40:34 +08:00
7e14f3ca4e
compiler,gateware: atomic now stores
2018-12-02 05:06:46 +08:00
fd00021a52
ctlmgr: do not raise exceptions in Controllers.__setitem__. Closes #1198
2018-12-01 18:09:58 +08:00
7f55376c75
test_loopback_gate_timing: print input timing for debugging
2018-12-01 18:09:53 +08:00
dce4f036db
grabber: work around windows numpy int peculiarity (same as a81c12de9)
2018-11-30 18:41:14 +08:00
156afb48ee
language: fix syscall arg handling
2018-11-30 17:59:24 +08:00
Paweł K
57caa7b149
artiq_flash: add command to erase flash memory ( #1197 )
2018-11-28 12:33:32 +02:00
c56c0ba41f
rtio/dds: use write-only RT2WB
...
This saves one address bit and prevents issues with AD9914 and 8-bit addresses.
2018-11-26 07:38:15 +08:00
09141e5bee
rtio/wishbone: support write-only interface
2018-11-26 07:38:06 +08:00
450a035f9e
suservo: move overflowing RTIO address bits into data
2018-11-26 06:54:20 +08:00
ae8ef18f47
rtlink: sanity-check parameters
2018-11-26 01:14:02 +08:00
b32e89444c
Merge branch 'master' into new
2018-11-26 01:02:19 +08:00
af9ea1f324
gui: update background
2018-11-26 01:01:36 +08:00
a81c12de94
urukul: work around windows numpy int peculiarity
...
"OverflowError: Python int too large to convert to C long" otherwise
opticlock#74
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-25 16:56:45 +01:00
8f9858be4c
ad9914: remove automatic continuous phase compensation (like Urukul)
2018-11-19 22:00:20 +08:00
22a223bf82
examples/master: clean up remnants of early urukul tests
2018-11-19 21:42:41 +08:00
53e79f553f
Merge branch 'master' into new
2018-11-19 11:54:50 +08:00
a3e0b1c5b4
ad9914,spi2: add warnings about driver state and DMA. Closes #1113
2018-11-17 22:10:20 +08:00
78d4b3a7da
gateware/targets: expose variant lists
...
This allows writing scripts that build all variants.
2018-11-17 22:10:20 +08:00
69e699c7bd
ttl: compensate for SED latency in input gating
...
Closes #1137
2018-11-17 22:10:20 +08:00
3ad68f65c5
urukul: make get_att_mu() not alter state
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-16 14:56:26 +00:00
d1eee7c0ea
ad9910: ensure sync is driven when required
...
close #1194
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-16 13:21:01 +00:00
1b841805f6
Merge branch 'master' into new
2018-11-16 15:20:32 +08:00
d3483c1d26
kasli: fix SDRAM read delay reset/wrap issue. Closes #1149
2018-11-15 19:40:35 +08:00
494ffca4d3
gui,scan: add CenterScan Scannable variant
...
* parametrized by center/span/step instead of
start/stop/npoints which is more convenient in some applications
* no scan widget support so far
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-15 13:30:43 +08:00
f77a75ab17
test_ad9910: robustify w.r.t. profile synchronization
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-14 08:42:27 +01:00
c3178c2cab
ad9910: profile support
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-14 08:30:28 +01:00
d0cadfeb4b
ad9910: more idiomatic register names
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-14 07:55:01 +01:00
a52d1be140
urukul: expose PROFILE setting
...
* add documentation
* add unittest
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-14 07:43:56 +01:00
2af6edb8f5
eem: fix reset/sync in suservo
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-13 13:00:54 +00:00
whitequark
248c1cf7dc
firmware: fix another TOCTTOU race in sync/async RPC code.
2018-11-13 00:58:20 +08:00
whitequark
68aad3e482
firmware: fix TOCTTOU race in sync/async RPC code.
...
Before this commit, the main loop in session code was laid like:
1. process_kern_queued_rpc
2. process_host_message
3. process_kern_message
If a host message (such as an RPC reply) caused the kernel to exit,
then any async RPCs would not complete, since RunFinished immediately
shuts down the kernel.
Fix this by reordering 1 and 2.
2018-11-13 00:57:09 +08:00
whitequark
dd829afebd
firmware: fix another TOCTTOU race in sync/async RPC code.
2018-11-12 15:42:07 +00:00
whitequark
583bba8777
Revert "firmware: workaround for RPC failures"
...
This reverts commit 59033d2588
2018-11-12 15:36:36 +00:00
whitequark
0edae64afb
firmware: fix TOCTTOU race in sync/async RPC code.
...
Before this commit, the main loop in session code was laid like:
1. process_kern_queued_rpc
2. process_host_message
3. process_kern_message
If a host message (such as an RPC reply) caused the kernel to exit,
then any async RPCs would not complete, since RunFinished immediately
shuts down the kernel.
Fix this by reordering 1 and 2.
2018-11-12 15:30:59 +00:00
59033d2588
firmware: workaround for RPC failures
2018-11-12 19:51:54 +08:00
84a6b3d09b
runtime: fix DMA recording after now-pinning
2018-11-10 14:14:55 +08:00
a4997c56cf
ad9910: simplify edge detection logic
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-09 18:54:34 +00:00
14b6b63916
ad9910: rewire io_delay tuning
...
This now reliably locates the SYNC_CLK-IO_UPDATE edge by doing two
scans at different delays between start and stop IO_UPDATE.
It also works well when one delay is very close to the edge.
And it correctly identifies which (start or stop) pulse hit or crossed
the SYNC_CLK edge.
for #1143
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-09 18:38:27 +00:00
1f7858b80b
test/dsp: fix rtio_output
2018-11-09 22:11:44 +08:00
e509ab8553
test/dsp: use absolute import path
...
Avoids "ImportError: attempted relative import with no known parent package"
when doing a simple "python -m unittest test_XXX.py".
2018-11-09 22:10:46 +08:00
38c6878d49
urukul: mention min/max attenuation
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-09 13:32:05 +01:00
e565ca6b82
urukul: slow down att write to datasheet limit
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-09 13:23:06 +01:00
998be50f07
urukul: handle MSB in att_reg
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-09 13:21:14 +01:00
c990b5e4f1
Merge remote-tracking branch 'origin/master' into new
2018-11-08 20:21:56 +08:00
a0cc7311ad
test: tighten test_pulse_rate
2018-11-08 20:17:55 +08:00
0bee43aa58
sawg: use new rtio_output() API
2018-11-08 20:16:30 +08:00
bec25cbaa0
suservo: use new rtio_output() API
2018-11-08 20:13:14 +08:00
e8d58b35b4
spi2: use new rtio_output() API
2018-11-08 20:12:30 +08:00
d18546550e
grabber: use new rtio_output() API
2018-11-08 19:15:50 +08:00
2549e623c1
ad9914: use new rtio_output() API
2018-11-08 19:15:44 +08:00
David Nadlinger
9740032a94
firmware: Fix dma_record_output_wide
2018-11-08 11:06:43 +00:00
f74dda639f
drtio: 8-bit address
2018-11-08 18:36:20 +08:00
8caea0e6d3
gateware,runtime: optimize RTIO kernel interface further
...
* now pinning (TODO: atomicity)
* for inputs, merge request and timeout registers
2018-11-08 18:29:24 +08:00
fcb611d1d2
test_ad9910: don't expect large SYNC_IN delay margins
...
sinara-hw/Urukul#16
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-07 18:18:35 +01:00
aadf5112b7
rtio: remove incorrect comment
2018-11-08 00:02:44 +08:00
fae95e73ad
ttl: use optimized rtio_output API
2018-11-07 23:41:43 +08:00
3d0c3cc1cf
gateware,runtime: optimize RTIO output interface
...
* reduce address to 8 bits
* merge core, channel and address into 32-bit pre-computable "target"
* merge we register into data register
2018-11-07 23:39:58 +08:00
e6efe830c4
ad9910: rewire sync delay tuning
...
* search from wide window end
* decouple margins and minimum window size
* add note about kasli jitter
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-07 14:52:03 +00:00
ad0254c17b
Merge branch 'switching125' into new
2018-11-07 22:03:18 +08:00
efd735a6ab
Revert "drtio: monitor RTIOClockMultiplier PLL ( #1155 )"
...
This reverts commit 469a66db61
2018-11-07 22:01:03 +08:00
6c00ab57c0
test_ad9910: relax SYNC window
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-06 19:31:38 +01:00
172633c7da
test_ad9910: default to a useful seed
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-06 17:35:57 +01:00
0b2661a34d
ad9910: robustify SYNC window finding
...
don't integrate too long, find the window tip fast and early
a couple 100 SYNC pulses are sufficient
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-06 12:41:21 +00:00
ba4bf6e59b
kasli: don't pass rtio pll feedback through bufg
...
UG472: "The MMCM performance increases because the
feedback clock is not subjected to noise on the core supply since it
never passes through a block powered by this supply."
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-06 11:58:55 +00:00
b6e4961b0f
kasli: lower RTIO clock jitter
...
* high bandwidth since the si5324 is good
* no low power ibufgds
* drop bufg between ibufgds and pll
* increase pll vco frequency to 1.5 GHz
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-06 11:43:19 +00:00
e17e458c58
ptb2: add sync to urukul0 for ad9910 usage
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-06 10:06:51 +00:00
73b7124091
test_ad9910: print sync scan for debugging
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-06 10:04:21 +01:00
9a3d81ffee
kasli: fix tester clk_sel
2018-11-06 14:49:21 +08:00
fb12df7e01
Revert "kasli_tester: urukul0 mmcx clock defunct"
...
This reverts commit 68220c316d
2018-11-06 14:33:21 +08:00
31f68ddf6c
Merge branch 'urukul-sync'
...
* urukul-sync: (29 commits)
urukul: flake8 [nfc]
ad9910: flake8 [nfc]
urukul/ad9910 test: remove unused import
test_urukul: relax speed
urukul,ad9910: print speed metrics
kasli: add PTB2 (external clock and SYNC)
kasli: add sync to LUH, HUB, Opticlock
kasli_tester: urukul0 mmcx clock defunct
test_ad9910: relax ifc mode read
tests: add Urukul-AD9910 HITL unittests including SYNC
ad9910: add init bit explanation
test: add Urukul CPLD HITL tests
ad9910: fiducial timestamp for tracking phase mode
ad9910: add phase modes
ad9910: fix pll timeout loop
tester: add urukul sync
ptb: back out urukul-sync
ad9910: add IO_UPDATE alignment and tuning
urukul: set up sync_in generator
ad9910: add io_update alignment measurement
...
close #1143
2018-11-05 19:54:30 +01:00
6fb18270a2
urukul: flake8 [nfc]
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:45:24 +01:00
832690af9a
ad9910: flake8 [nfc]
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:44:51 +01:00
6d525e2f9a
urukul/ad9910 test: remove unused import
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:40:57 +01:00
36c5a7cd04
test_urukul: relax speed
...
works fine at < 3µs here but needs <5 µs on buildbot-kasli-tester
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:37:20 +01:00
89fecfab50
urukul,ad9910: print speed metrics
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:37:18 +01:00
32d538f72b
kasli: add PTB2 (external clock and SYNC)
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:37:16 +01:00
d8a5951a13
kasli: add sync to LUH, HUB, Opticlock
...
for #1143 , also add missing LUH device db
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:37:14 +01:00
68220c316d
kasli_tester: urukul0 mmcx clock defunct
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:37:11 +01:00
89fadab63d
test_ad9910: relax ifc mode read
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:37:08 +01:00
f522e211ba
tests: add Urukul-AD9910 HITL unittests including SYNC
...
for #1143
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:37:06 +01:00
9fb850ae75
ad9910: add init bit explanation
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:37:02 +01:00
bc04da15c5
test: add Urukul CPLD HITL tests
...
for #1143
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:37:00 +01:00
141cc7d99f
ad9910: fiducial timestamp for tracking phase mode
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:58 +01:00
2f6d3f79ff
ad9910: add phase modes
...
* simplified and cross-referenced the explanation of the different
phase modes.
* semantically and functionally merged absolute and tracking/coherent
phase modes.
* simplified numerics to calculate phase correction
* added warning about possible inconsistency with DMA and default
phase mode
* restricted __all__ imports
* moved continuous/relative phase offset tracking from an instance
variable to a "handle" returned by set()/set_mu() in order to avoid
state inconsistency with DMA (#1113 #1115 )
for #1143
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:55 +01:00
d3ad2b7633
ad9910: fix pll timeout loop
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:53 +01:00
4269d5ad5c
tester: add urukul sync
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:52 +01:00
60d3bc63a7
ptb: back out urukul-sync
...
... for backwards compatibility.
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:50 +01:00
06139c0f4d
ad9910: add IO_UPDATE alignment and tuning
...
for #1143
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:48 +01:00
1066430fa8
urukul: set up sync_in generator
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:46 +01:00
4bbd833cfe
ad9910: add io_update alignment measurement
...
for #1143
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:44 +01:00
7b92282012
ad9910: add docs for sync tuning, refactor
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:42 +01:00
8a47a6b2fb
ad9910: disable sync_clk output
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:40 +01:00
65e2ebf960
ad9910: add sync delay control, auto tuning
...
* expose multi device sync functionality
* sync delay configuration interface
* auto-tuning of sync delay from device_db seed
for #1143
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:37 +01:00
8dbf5f87fd
ad9910: simplify io_update pulsing on init, set_mu
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:35 +01:00
0b3b07a7da
ad9910: add power down method
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:34 +01:00
3538444876
urukul: add sync_in to eem0-7 name
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:32 +01:00
0433e8f4fe
urukul: add sync_in generator
...
for #1143
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:30 +01:00
f62c1ff0bb
TTLClockGen: expose acc_width
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:27 +01:00
f755a4682a
device_db_ptb: fix zotino clr
...
Signed-off-by: Robert Jördens <rj@quartiq.de>
2018-11-05 19:36:24 +01:00
David Nadlinger
f79b9d9e1e
ttl: Expand input gate/count API docstrings
2018-11-03 20:33:19 +08:00
David Nadlinger
f02ceee626
language: Clarify now_mu() docstring [nfc]
2018-11-03 20:33:19 +08:00
David Nadlinger
5d2e3f975f
coredevice: Add get_rtio_counter_mu() docstring [nfc]
2018-11-03 20:33:19 +08:00
David Nadlinger
d6fcc0529f
coredevice: Imperative mood in docstrings [nfc]
...
This follows Python conventions (PEP257) and unifies the style with
other comments.
2018-11-03 20:33:19 +08:00
David Nadlinger
cbdef0225c
ttl: Add target RTIO time argument to timestamp/count functions
...
Software-based tracking of timestamps is problematic (e.g. when
using DMA, see GitHub #1113 ).
2018-11-03 20:33:19 +08:00
David Nadlinger
2a0e1dabfb
ttl: Remove unused attribute [nfc]
2018-11-03 20:33:19 +08:00
David Nadlinger
17a5fb2dce
ttl: Remove error-prone sync() calls
...
These methods are problematic, as with DMA in the picture, the
timestamp member variables did not necessarily reflect the last
submitted event timestamp (see GitHub #1113 ).
sync() is only very rarely used in typical experimental code, so
the methods are removed without a transition period.
Core.wait_until() can be used to busy-wait for a specified RTIO
timestamp value on the core device CPU instead.
2018-11-03 20:33:19 +08:00
David Nadlinger
11e8c9d5f7
coredevice: Add Core.wait_until_mu()
...
(This supersedes TTLOut.sync(), see see GitHub #1113.)
2018-11-03 20:33:19 +08:00
David Nadlinger
cbfbe24d7a
ttl: Remove broken TTLClockGen.sync
...
The code currently doesn't compile because of a typo in the timestamp
field name. However, tracking event timestamps in software is
problematic anyway (e.g. with DMA, see GitHub #1113 ), so just remove
`sync()` altogether.
2018-11-03 20:33:19 +08:00
bc4a8157c0
kasli: add tsinghua2
2018-11-01 18:26:37 +08:00
89a961fb00
urukul, ad9912, ad9910: expose CFG RF switch better
...
* conincident setting of multiple switches
* per channel setting
2018-10-24 13:04:46 +02:00
48a142ed63
use FutureWarning instead of DeprecationWarning
...
DeprecationWarning is disabled by default and too easy to ignore.
2018-10-21 12:14:51 +08:00
9793632282
enviromnment: rename 'save' in set_dataset to 'archive'. Closes #1171
2018-10-21 12:08:34 +08:00
Marius Weber
029f9d983a
Tpz fixes ( #1178 )
...
* flake8
* fix TPZ constructor after move to asyncio
* Tcube fix docummentation in set_channel_enable_state
2018-10-20 20:49:15 +08:00
c52a6ca8e9
typo ( #1179 )
2018-10-20 20:40:07 +08:00
Florent Kermarrec
3318925f4e
firmware/liboard_misoc/sdram: use similar loops on read_level_scan and read_level for consistent results
2018-10-16 09:40:39 +02:00
6357a50d33
kasli: update nudt variant
2018-10-15 18:04:57 +08:00
David Nadlinger
e3cfbfed06
master: Add minimal docstring to worker_impl [nfc]
2018-10-14 10:41:32 +08:00
David Nadlinger
64b9a377da
master: Factor RIDCounter out into own module, explain worker_db module [nfc]
...
The docstrings are quite minimal still, but should already
help with navigating the different layers when getting
accustomed with the code base.
RIDCounter was moved to its own module, as it isn't really
related to the other classes (used from master only).
2018-10-14 10:41:32 +08:00
David Nadlinger
4641ddf002
master: Remove unused import [nfc]
2018-10-14 10:41:32 +08:00
661dd00c4c
ad9912: phase offset is 14 bit LSB aligned
...
c.f. sinara-hw/Urukul#15
2018-10-11 15:16:08 +02:00
hartytp
08074d5275
Urukul: add support for hardware v1.3 clocking options
2018-10-10 09:26:35 +02:00
469a66db61
drtio: monitor RTIOClockMultiplier PLL ( #1155 )
...
Debugging by Tom Harty
2018-10-08 14:50:02 +02:00
hartytp
1a1b454ed9
Urukul: flake8 (NFC)
2018-10-08 10:09:49 +01:00
5de319d76a
bit2bin: don't print string terminator
2018-10-08 10:13:03 +02:00
hartytp
9a509e5070
Zotino: increase delay after register read in init method to avoid underflows
2018-10-06 21:45:17 +08:00
86fe6b0594
kasli: add NUDT variant
2018-10-04 23:20:09 +08:00
a89bd6b684
kasli: swap Urukul EEMs for Tester
...
Updated to Urukul 1.3.
2018-10-04 23:19:31 +08:00
9f96b6bcda
kasli: use 125MHz DRTIO freq for testing
2018-10-04 10:41:01 +08:00
969a305c5a
Merge branch 'master' into switching125
2018-10-04 10:08:42 +08:00
d0ee2c2955
opticlock: external 100 MHz
2018-09-28 19:05:18 +02:00
3b3fddb5a4
kasli: add mitll2
2018-09-27 23:21:52 +08:00
998a468983
examples: add grabber to device databases
2018-09-27 16:09:25 +08:00
c71e442929
documentation improvements
...
Based on PR #1101 by @drewrisinger
2018-09-26 12:12:37 +08:00
b92350b0f6
drtio: monitor RTIOClockMultiplier PLL ( #1155 )
...
Debugging by Tom Harty
2018-09-26 10:52:08 +08:00
53c7a5f2c6
dashboard: fix TTL moninj level display
2018-09-26 10:32:08 +08:00
212892d92f
style
2018-09-26 10:13:33 +08:00
20cddb6a25
tester: handle no available ttl outputs
2018-09-24 09:19:28 +00:00
73f0de7c79
sayma: DRTIO master fixes
2018-09-20 11:15:45 +08:00
1b7f403a4b
drtio: remove remote RTIO PHY resets
2018-09-20 11:10:32 +08:00
53a979e74d
rtio: cleanup resets
2018-09-20 10:58:38 +08:00
251d90c3d5
drtio: clear read request in satellite only after reply has been fully sent
...
Otherwise, chan_sel become invalid before the end of the packet, which
can cause the interconnect to invalidate i_timestamp and i_data which results
in corruption of the end of the packet.
2018-09-20 08:53:45 +08:00
69d060b639
drtio: fix satellite i_status handling
2018-09-19 20:57:21 +08:00
b86b6dcc09
drtio: add switching input test
2018-09-19 17:50:29 +08:00
08be176369
drtio: fix satellite i_status handling
2018-09-19 17:50:18 +08:00
3d965910f7
Revert "drtio: implement per-destination underflow margins"
...
This reverts commit 142c952e3d
2018-09-19 17:05:48 +08:00
142c952e3d
drtio: implement per-destination underflow margins
2018-09-19 17:03:15 +08:00
62642957cd
runtime: fix DRTIO aux channel race condition
2018-09-19 11:16:21 +08:00
David Nadlinger
b482f5feae
firmware: Use larger ARP cache
...
This works around a problematic interaction between ARP cache
expiry in smoltcp (with its 3 seconds timeout before a discovery
request is sent) and our TCP keepalive settings, where the timeout
is reached before the keepalive had a chance to be sent.
GitHub: Closes #1150 .
2018-09-18 14:46:52 +00:00
970d1bf147
drtio: add switching unittest
2018-09-18 15:27:52 +08:00
eda15a596c
drtio: add buffering to repeater
2018-09-18 15:27:25 +08:00
2b44786f73
drtio: add repeater input support
2018-09-17 23:45:27 +08:00
whitequark
c33f74dabe
firmware: derive Clone for Mutex.
2018-09-15 15:24:44 +00:00
c8cd830118
drtio: implement get_rtio_destination_status for kernels
2018-09-15 19:11:22 +08:00
f7ad7a99e3
firmware: set DEST_COUNT to 0 without routing
2018-09-15 19:10:52 +08:00
3cbdf2fbac
kasli: cleanup drtio blink example
2018-09-15 18:43:27 +08:00
d38755feff
drtio: implement destination state checks on operations
2018-09-15 15:55:45 +08:00
whitequark
1990ab35d3
firmware: implement mutexes.
2018-09-15 07:35:35 +00:00
cd61ee858c
kasli: fix satellite TSC instantiation
2018-09-15 14:06:54 +08:00
7565d816e4
frontend: remove artiq_pcap. Closes #1152
2018-09-15 12:09:37 +08:00
eaeab0c9bd
frontend: add artiq_rtiomon
2018-09-15 12:09:32 +08:00
c0c413196a
frontend: remove artiq_pcap. Closes #1152
2018-09-15 12:08:06 +08:00
f097b4104c
satman: not(has_drtio_routing) fixes
2018-09-15 12:06:47 +08:00
0017cb756e
frontend: add artiq_rtiomon
2018-09-15 10:44:59 +08:00
2f010e0109
runtime: improve moninj aux error logging
2018-09-15 10:44:41 +08:00
20ed393c1e
style
2018-09-15 10:43:50 +08:00
f8c6fa5ad6
typo
2018-09-15 10:43:36 +08:00
65da1fee4a
firmware: fix build without DRTIO
2018-09-14 20:38:41 +08:00
d19550daf8
firmware: simplify drtioaux function names
2018-09-14 20:32:09 +08:00
ae72e3a51e
firmware: add support for moninj and kern_hwreq over DRTIO switching
2018-09-14 20:26:39 +08:00
1ef39a98a7
drtio: implement per-destination buffer space
2018-09-13 16:16:32 +08:00
e95638e0a7
style
2018-09-13 15:54:28 +08:00
042b0065de
runtime: print destination up message for local RTIO
2018-09-13 14:10:52 +08:00
fa872c3341
firmware: implement DRTIO destination survey
2018-09-13 12:00:29 +08:00
6cf3db3485
satman: forward RTIO resets
2018-09-12 23:02:54 +08:00
5a9cc004f2
drtio: receive and print unsolicited aux packets
...
Helps with debugging and prevents the aux channel from getting stuck after packets arrive after the timeout.
2018-09-12 22:57:21 +08:00
0befec7d26
drtio: improve repeater error reports
2018-09-12 20:54:01 +08:00
420e1cb1d0
cri: fix firmware routing table access
2018-09-12 18:08:16 +08:00
e36a8536d7
runtime: better handling of aux timeouts
2018-09-12 17:31:23 +08:00
5bcd40ff59
cri: fix routing table depth
2018-09-12 17:30:55 +08:00
edf403b837
drtio: improve error reporting
2018-09-12 15:44:34 +08:00
95432a4ac1
drtio: remove old debugging features
2018-09-12 13:01:27 +08:00
8227037a84
examples: add kasli_drtioswitching
2018-09-11 22:20:18 +08:00
41972d6773
drtio: rt_packet_satellite CRI fixes
2018-09-11 22:19:55 +08:00
051bafbfd9
drtio: ensure 2 cycles between frames on the link
...
This gives time for setting chan_sel before cmd on CRI.
2018-09-11 22:18:42 +08:00
251b9a2b0d
drtio: do not lock up master when satellite repeatedly fails to answer buffer space reqs
2018-09-11 22:17:57 +08:00
5439abaa9d
satman: fix error messages
2018-09-11 20:10:52 +08:00
36e3fedfc6
runtime: print routing table at boot
2018-09-11 20:10:33 +08:00
e6bd835b5d
satman: fix rank setting
2018-09-11 20:04:51 +08:00
2679a35082
firwmare: propagate DRTIO routing table and rank all the way
2018-09-11 18:28:17 +08:00
c0c5867f9e
satman: increase stack size
...
Prevents crashing when running the routing code.
Will have to be shrunk back on Sayma RTM.
2018-09-11 18:23:51 +08:00
a23af67f2b
satman: print better debugging information on exception
2018-09-11 18:23:36 +08:00
f5b386c0d8
firmware: fix routing table formatting
2018-09-11 18:22:45 +08:00
b38c57d73b
firmware: send DRTIO routing table to satellite
2018-09-11 14:12:41 +08:00
3d29a7ed14
firmware: add fmt::Display to RoutingTable
2018-09-11 11:27:56 +08:00
2fff96802b
runtime: remove support for building without RTIO
2018-09-10 23:09:02 +08:00
19a14b68b1
runtime: program DRTIO routing table into gateware
2018-09-10 22:48:56 +08:00
264078baba
style
2018-09-10 22:29:35 +08:00
e01efbcb8a
runtime: merge sync_tsc and wait_tsc_ack
2018-09-10 22:17:00 +08:00
4d889c0c4e
firmware: improve DRTIO log messages
2018-09-10 21:40:02 +08:00
663432adbd
satman: load TSCs of downstream devices
2018-09-10 20:34:33 +08:00
bc1d3fda6a
satman: ping repeater links
...
Tested OK on hardware.
2018-09-10 20:17:13 +08:00
31bef9918e
firmware: fix drtio_routing compatibility with master and satellite
2018-09-10 20:16:42 +08:00
7ec45efdcf
kasli: add missing cri_con to Satellite
2018-09-10 20:16:09 +08:00
014cfd8dbd
firmware: add drtioaux routing packets
2018-09-09 22:44:25 +08:00
7ae44f3417
firmware: add routing table (WIP)
2018-09-09 21:49:28 +08:00
496d1b08fd
kasli: enable routing in Master
2018-09-09 21:48:12 +08:00
ec302747e0
kasli: add DRTIO repeaters
2018-09-09 16:27:39 +08:00
d5577ec0d0
cri: add routing table support
2018-09-09 16:26:48 +08:00
df61b85988
drtio: fix imports
2018-09-09 14:11:32 +08:00
312256a18d
grabber: fix frame size off-by-1
2018-09-07 16:55:43 +02:00
ec62eb9373
drtio: minor cleanup
2018-09-07 17:51:38 +08:00
4d73fb5bc9
grabber: only advance when DVAL
2018-09-06 11:01:08 +02:00
87e0384e97
drtio: separate aux controller
...
This helps with managing CSR groups and heterogeneous (satellite/repeaters) DRTIO cores.
2018-09-05 17:56:58 +08:00
92be9324df
add missing files
2018-09-05 16:09:02 +08:00
2884d595b3
drtio: add rt_controller_repeater
2018-09-05 16:08:40 +08:00
839f748a1d
drtio: add external TSC to repeater
2018-09-05 15:55:20 +08:00
5f20d79408
drtio: add timeout on satellite internal CRI buffer space request
2018-09-05 14:12:11 +08:00
1450e17a73
sayma: adapt to TSC and DRTIOSatellite changes
2018-09-05 12:10:41 +08:00
19ae9ac1b1
kc705: adapt to TSC changes
2018-09-05 12:07:28 +08:00
3d531cc923
kasli: adapt to TSC and DRTIOSatellite changes
2018-09-05 12:06:47 +08:00
4e4398afa6
analyzer: adapt to TSC changes
2018-09-05 12:06:20 +08:00
15b16695c6
frontend: add artiq_route
2018-09-04 19:04:27 +08:00
bf36786d45
kasli_tester: clean up grabber test
2018-09-04 10:59:19 +00:00
47eb37e212
VLBAI{Master,Slave}: align rtio channels with PTB
2018-09-04 10:39:45 +00:00
778f1de121
drtio: add TSC sync and missed command detection to rt_packet_repeater
2018-09-03 18:26:13 +08:00
hartytp
c55460f59f
suservo: fix doc typo
2018-09-03 11:48:40 +02:00
00fabee1ca
drtio: fix rt_packet_repeater timeout
2018-09-03 09:57:15 +08:00
f3fe818049
rtio: refactor TSC to allow sharing between cores
2018-09-03 09:48:12 +08:00
0fe2a6801e
drtio: forward destination with channel
2018-09-02 15:50:23 +08:00
6768dbab6c
drtio: add buffer space support to rt_packet_repeater
2018-09-02 14:38:37 +08:00
88b7529d09
drtio: share CDC
2018-09-02 14:37:29 +08:00
078c862618
drtio: add repeater (WIP, write only)
2018-09-01 21:07:55 +08:00
6057cb797c
drtio: reorganize tests
2018-08-31 16:28:33 +08:00
4f963e1e11
drtio: minor cleanup
2018-08-30 15:15:32 +08:00
ce6e390d5f
drtio: expose internal satellite CRI
2018-08-30 12:41:09 +08:00
e7dba34475
kasli/tester: fill all 12 EEM
2018-08-29 18:09:09 +00:00
b58ec2d78e
artiq_flash: treat all variants ending in satellite as such
2018-08-29 17:53:48 +00:00
fbf05db5ab
kasli: add VLBAI Master and Satellite
2018-08-29 17:53:48 +00:00
9584c30a1f
kasli: DRTIO Base: flexible rtio_clk_freq
2018-08-29 17:53:48 +00:00
eb9e9634df
siphaser: support 125 MHz rtio clk
...
keep the phase shift increment/decrement at 1/(56*8) rtio_clk
cycles
2018-08-29 17:53:48 +00:00
ccc58a0f84
satman: add 125 MHz Si5324 settings
...
from cjbe
2018-08-29 17:53:48 +00:00
aa64e6c1c6
cri: add buffer space request protocol
2018-08-29 15:16:43 +08:00
ba6094c3e5
test: relax network transfer rates
...
Due to lower Kasli system clock frequency.
2018-08-27 16:47:48 +08:00
whitequark
0e7419450e
firmware: update smoltcp.
...
This adds TCP window scaling support.
2018-08-20 00:26:40 +00:00
9b6ea47b7a
kasli: use SFP LEDs to show DRTIO link status. Closes #1073
2018-08-19 13:04:41 +08:00
d1d26e2aa3
hmc7043: add explanation about HMC_SYSREF_DIV
2018-08-18 11:43:40 +08:00
f75a317446
hmc7043: automatically determine output groups
2018-08-18 11:43:23 +08:00
c498b28f88
hmc7043: disable FPGA_ADC_SYSREF
2018-08-18 11:42:57 +08:00
a7810502f6
artiq_coremgmt: add option to specify core device address directly
2018-08-18 10:58:40 +08:00
fc09144baa
artiq_coremgmt: remove unnecessary DeviceManager
2018-08-18 10:46:08 +08:00
167e97efd2
sayma: support external RTM clocking
2018-08-17 22:57:54 +08:00
041dc0f64a
jesd204: update core to v0.10
...
Closes #727
Closes #1127
2018-08-17 22:50:07 +08:00
5c3e834c4d
ad9154: retry DAC initialization on STPL or PRBS failure
...
Works around #1127
2018-08-17 20:52:55 +08:00
66e33a66d6
test: enable TTL loopback tests on Kasli
2018-08-17 13:35:55 +08:00
d707d2f4fe
test: relax TTL timing requirements to support DIO EEM
2018-08-17 13:35:16 +08:00
1ba12e1cdb
gui/log: print messages in tooltips
...
This helps reading long messages in small log windows.
2018-08-17 13:21:38 +08:00
David Nadlinger
2463e5667d
compiler: Fix attribute writeback with skipped fields
...
offset wasn't advanced for skipped fields previously,
leading to memory corruption/unaligned accesses at runtime.
2018-08-14 13:34:32 +01:00
c172ec6de9
artiq_flash: target Kasli by default
2018-08-13 12:13:21 +08:00
David Nadlinger
0e32a165c2
satman: Fix build with Rust 1.28
...
The build was broken in 2648b1b7a1
2018-08-13 00:12:27 +01:00
whitequark
e285fe0d56
test: tighten required TransferTest timings.
...
smoltcp performs significantly better with LTO.
2018-08-12 20:17:37 +00:00
whitequark
46bd96abd1
artiq_devtool: make kasli-tester the default configuration.
2018-08-12 19:17:45 +00:00
whitequark
38d60100ff
firmware: optimize dma_record_output.
...
This removes a number of bounds checks and adds a fast path for
outputting exactly one word to DMA, which is the most common
operation.
2018-08-12 19:17:45 +00:00
whitequark
bdd18de2c1
firmware: globally enable LTO.
...
This used to crash with earlier rustc versions, but doesn't anymore,
and gives significant speedup (e.g. 2x on test_dma_record_time).
2018-08-12 19:17:45 +00:00
whitequark
2648b1b7a1
firmware: migrate to Rust 1.28.0.
...
This also updates / is a prerequisite for updating smoltcp.
Rationale for changes made:
* compiler_builtins is now shipped in the rust prefix.
* rustc's libpanic_unwind no longer works for us because it
has a hard dependency on Box (and it's a horrible hack);
fortunately, we only ever needed a personality function
from it.
* panic and oom handlers are now set in a completely different
way.
* allocators are quite different (and finally stable).
* NLL caused internal compiler errors in runtime, so code using
NLL was rewritten to not rely on it and it was turned off.
2018-08-12 19:17:45 +00:00
738d2c6bcb
hmc7043: REFSYNCIN → RFSYNCIN
2018-08-11 12:07:17 +08:00
bc3e715a8f
examples: fix kasli_tester
2018-08-11 10:51:42 +08:00
whitequark
fab6e5cdff
compiler: skip functional values in attribute writeback.
...
Fixes #1088 .
2018-08-10 12:02:49 +00:00
052e400f12
test: skip test_dma_playback_time on Kasli ( #946 )
2018-08-09 18:08:21 +08:00
957645a7e7
examples: move kasli tester out of kasli_basic
2018-08-09 18:07:44 +08:00
bbc98410e4
test: dds → ad9914dds
...
Prevent confusion with Urukul.
2018-08-09 16:55:09 +08:00
bf78e0c7d2
test: fix handling of missing devices
2018-08-09 16:51:12 +08:00
a061ba2505
grabber/kasli_basic: add grabber test
...
close #1121
2018-08-08 12:43:44 +02:00
f7678cc24a
grabber: refactor state machine
2018-08-07 18:07:46 +02:00
6cd2432e30
grabber: log all resolution changes
...
close #1120
2018-08-07 16:21:21 +02:00
99a15ca0c6
grabber: rationalize derived traits
2018-08-07 16:21:21 +02:00
49f7a1610f
sayma: use GTP_CLK1 only for all variants ( #1080 )
2018-08-07 20:53:14 +08:00
e2a49ce368
drtio: support external IBUFDS_GTE3
2018-08-07 20:52:45 +08:00
8b8e1844f0
kasli_sawgmaster: roughly match Urukul and Sayma amplitudes
2018-08-07 20:07:21 +08:00
9ce6233926
kasli: fix SYSU TTL directions
2018-08-07 19:29:28 +08:00
8aa88cfe70
kasli_sawgmaster: add Urukul-Sayma example
2018-08-07 19:29:28 +08:00
474bc7b65b
browser: handle windows file urls for feeding h5py
...
close #1014
2018-08-07 12:57:01 +02:00
whitequark
93af5d2a03
compiler: handle async RPC as last statement in try block.
...
Fixes #1107 .
2018-08-07 07:06:53 +00:00
whitequark
7bd7b6592a
rpc_proto: serialize keywords correctly.
...
Fixes #1109 .
2018-08-07 06:47:09 +00:00
whitequark
259f1576c3
Fix tests after a74958f0.
2018-08-07 06:06:49 +00:00
whitequark
a74958f01f
ksupport: raise RuntimeError on reraise with no inflight exception.
...
Fixes #1123 .
2018-08-07 05:53:13 +00:00
2008d02f4d
runtime: use different default IP and MAC for different kinds of boards
...
This helps reduce conflicts when having many boards on a development network.
2018-08-07 10:30:50 +08:00
bbe36b94f7
ad9154: enable sync in init
2018-08-06 19:02:27 +08:00
7f0b2ff594
jesd204sync: work around HMC7043 poor behavior with combined delays
...
The HMC7043 outputs poorly controlled signals when adjusting
two delays at once. This commit puts the DAC in one-shot SYSREF mode,
and only triggers synchronizations when SYSREF is stable.
2018-08-06 17:43:17 +08:00
f32f0126e2
Revert "ad9154: use continuous sync mode"
...
The HMC7043 is not really glitchless.
This reverts commit bd968211de
2018-08-06 16:59:53 +08:00
65f198bdee
kasli: use tester EEMs for DRTIO, add Urukul-Sayma sync example
2018-08-06 16:53:13 +08:00
bd968211de
ad9154: use continuous sync mode
2018-08-06 00:27:10 +08:00
b023865b42
sayma: instantiate dummy IBUFDS_GTE3 on unused but driven Si5324 clock pins
...
Solve same problem as e83ee3a0
2018-08-05 23:02:41 +08:00
e83ee3a07a
hmc7043: disable GTP_CLK1 when not in use
...
Termination and biasing are not active at the FPGA when IBUFDS_GTE3 is
not instantiated, and driving a clock then leads to overvoltage.
2018-08-03 10:03:52 +08:00
6fc8439399
tweak moninj to allow old dashboard with new firmware
2018-08-02 19:34:14 +08:00
04cbc3237b
test_moninj: test injection monitoring
2018-08-02 19:34:14 +08:00
47740c8930
share moninj injection state between dashboards
...
Previously if one dashboard overrode a channel this was not visible on
any other dashboard - the channel appeared to operate normally.
2018-08-02 19:34:14 +08:00
7d6a1b528d
ad9912: add ftw_to_frequency
2018-08-02 11:19:12 +00:00
e518a1f1d0
ad53xx: also increase slack after control readback
2018-08-02 11:19:12 +00:00
whitequark
5871d13da8
firmware: actually compact in config::compact().
...
Fixes #1116 .
2018-08-01 16:27:48 +00:00
David Nadlinger
829fca6112
pyon: Correctly deserialize bare NaNs
...
This also fixes (non-numpy) lists containing NaNs.
Previously, accidentally storing a NaN in a dataset would
bring down large parts of the system.
2018-07-30 11:08:56 +01:00
David Nadlinger
08ee91beb2
ad9910: Clarify chip_select range [nfc]
...
`assert 3 <= chip_select <= 7` is rather opaque without looking
at the CPLD source code otherwise.
2018-07-30 11:08:17 +01:00
David Nadlinger
6b89106578
ad53xx: Avoid sporadic RTIOUnderflow in init()
...
I observed sporadic RTIO underflows on Kasli before, by ~2.5 µs,
so 5 µs extra slack should be plenty. No underflows since.
2018-07-28 23:45:48 +01:00
e4d48a78eb
drtio: wait for remote to ack TSC synchronization
...
Sayma takes a long time after TSC sync to align SYSREF, and this caused two issues:
1. Aux packets getting lost and causing error reports
2. DRTIO links reported up and kernels proceeding despite the DACs not being properly synced.
2018-07-26 20:28:17 +08:00
83de8b2ba2
drtio: add ping timeout during link init
2018-07-26 20:27:53 +08:00
446f791180
firmware: simplify SYSREF DRTIO alignment
2018-07-26 19:37:59 +08:00
f8c17528e7
satman: use new SYSREF code
2018-07-26 16:26:57 +08:00
32c95ac034
sayma: automated DAC SYSREF phase calibration
2018-07-26 16:23:55 +08:00
dbcf2fe9b4
firmware: remove 'chip found' messages on Sayma
2018-07-26 16:07:37 +08:00
d523d03f71
sayma: automated FPGA SYSREF phase offset calibration
2018-07-26 14:53:28 +08:00
0a9d3638ee
config: add write_int
2018-07-26 14:49:32 +08:00
19c51c644e
grabber: cleanup GRABBER_STATE
2018-07-24 19:08:51 +08:00
fb96c1140e
grabber: add coredevice driver
2018-07-24 18:06:44 +08:00
b38c685857
grabber: fix pix.stb
2018-07-24 11:32:32 +08:00
60a7e0e40d
grabber: use usual order of ROI coordinates in cfg addresses
2018-07-24 10:55:13 +08:00
7b75026391
grabber: add MultiReg to transfer ROI boundaries
2018-07-21 13:40:12 +08:00
4a4d0f8e51
grabber: fix missing variable rename
2018-07-21 13:39:46 +08:00
3638a966e1
kasli: add false path between RTIO and CL clocks
2018-07-21 13:26:13 +08:00
031de58d21
grabber: complete RTIO PHY, untested
2018-07-21 13:25:47 +08:00
e3ba4b9516
grabber: minor ROI engine cleanup, export count_len, cap count width to 31
2018-07-21 13:25:13 +08:00
cab0ba408d
fmcdio_vhdci_eem: cleanup and document
2018-07-20 09:57:03 +08:00
d152506ecb
sayma: update fmcdio_vhdci_eem demo
2018-07-19 15:47:20 +08:00
8dfcd463aa
fmcdio_vhdci_eem: naming consistency
2018-07-19 15:46:04 +08:00
fe93a454d6
fmcdio_vhdci_eem: fix direction shift register permutation and polarity
2018-07-19 15:16:21 +08:00
e71cbe53a6
firmware: cleanup Cargo.lock
2018-07-18 10:37:43 +08:00
31f4f8792a
sayma: add Urukul and Zotino to example device_db
2018-07-18 10:31:55 +08:00
25170a53e5
sayma: add back Urukul and Zotino
2018-07-18 10:27:54 +08:00
5e62910a8d
examples: add Sayma VHDCI DIO
2018-07-17 23:28:05 +08:00
8b9a8be12a
fmcdio_vhdci_eem: add dirctl word computation functions
2018-07-17 23:27:29 +08:00
82145b1263
examples: sayma_drtio → sayma_masterdac
2018-07-17 20:32:30 +08:00
7fe76426fe
fmcdio_vhdci_eem: commit missing part of previous commit
2018-07-17 20:30:13 +08:00
d4d12e264d
fmcdio_vhdci_eem: refactor
...
This allows access to the pin allocation from kernels, which becomes useful
to configure the direction shift register.
2018-07-17 20:13:59 +08:00
4fdc20bb11
sayma: disable Urukul and Zotino for now
...
Ultrascale I/Os are being a pain as usual and the SPI core won't compile.
2018-07-17 20:08:21 +08:00
8335085fd6
fmcdio_vhdci_eem: fix cc pins
2018-07-17 19:50:34 +08:00
8f7c0c1646
fmcdio_vhdci_eem: fix iostandard
2018-07-17 19:40:34 +08:00
d724bd980c
sayma: add EEMs to Master
2018-07-17 18:58:23 +08:00
a0f2d8c2ea
gateware: add FMCDIO/EEM adapter definitions
2018-07-17 18:58:16 +08:00
3645a6424e
sayma: fix Master build
2018-07-17 18:56:33 +08:00
9b016dcd6d
eem: support specifying I/O standard
...
Xilinx FPGAs require different LVDS I/O standard names depending on I/O bank voltage.
2018-07-17 18:55:17 +08:00
3168b193e6
kc705: remove Zotino and Urukul
...
* use Kasli instead for using EEMs
* code required outdated VHDCI adapter 1.0
2018-07-17 17:48:57 +08:00
13984385a8
firmware: version → ident
2018-07-15 17:40:17 +08:00
b2695d03ed
sayma: remove with_sawg from Master variant
2018-07-15 17:38:29 +08:00
123e7bc054
pyon: sort string dicts by key when pretty-printing. Closes #1010
2018-07-15 17:38:09 +08:00
b27fa8964b
add variant in identifier string
...
Also add without-sawg suffixes on Sayma.
Closes #1060
Closes #1059
2018-07-15 17:21:17 +08:00
b6c70b3cb0
eem: add Zotino monitoring. Closes #1095
2018-07-15 15:35:04 +08:00
8bcba82b65
grabber: reset *_good signals on end of frame
...
This reduces the amount of time the ROI engine produces invalid output after
being reconfigured.
2018-07-15 15:34:00 +08:00
ea7f925852
Revert "worker_db: Only warn on repeated archive read if dataset changed"
...
Breaks numpy arrays.
This reverts commit 141fcaaa8a
2018-07-13 10:41:06 +08:00
46fb5adac3
grabber: fix frequency counter formula
2018-07-12 20:14:38 +08:00
82def6b535
grabber: add frequency counter
...
Cameras are a bit obscure about what they output, this can help with troubleshooting.
2018-07-12 17:05:18 +08:00
29c35ee553
hmc7043: fix dumb mistake in previous commit
2018-07-12 13:01:41 +08:00
8802b930de
hmc7043: add delay after init
...
Delay required at step 9 of the "Typical Programming Sequence" (page 24 of the datasheet)
2018-07-12 12:37:12 +08:00
c66f9483f8
hmc7043: wait after changing delays
...
Allows for the SPI transaction to finish, and for the delay to stabilize.
2018-07-12 12:33:53 +08:00
1c191a62bf
sayma: tune SYSREF phases
2018-07-12 12:33:35 +08:00
773240bef4
hmc7043: test GPO before using
...
Based on code by David.
2018-07-12 11:30:24 +08:00
David Nadligner
141fcaaa8a
worker_db: Only warn on repeated archive read if dataset changed
...
In larger experiments, it is quite natural for the same dataset
to be read from multiple unrelated components. The only situation
where multiple reads from an archived dataset are problematic is
when the valeu actually changes between reads. Hence, this commit
restricts the warning to the latter situation.
2018-07-12 10:15:42 +08:00
4843832329
hmc7043: check phase status on init. Closes #1055
...
Troubleshooting by David.
2018-07-11 19:45:24 +08:00
9397fa7f5a
hmc7043: unstick SYSREF FSM ( #1055 )
...
Troubleshooting by David.
Additionally, register 7D is broken.
Checking phase init state has to be done through another means.
2018-07-11 19:11:01 +08:00
88fb9ce4d6
sayma_rtm: add hmc7043_gpo monitoring
2018-07-11 19:04:29 +08:00
29e5c95afa
sayma_rtm: minor cleanup
2018-07-11 19:02:59 +08:00
7f05e0c121
sayma_rtm: remove UART loopback
...
RTM power supply issues are fixed now, plus this will get in the way of satman support.
2018-07-11 19:00:18 +08:00
f8ceea20d0
grabber: add new ROI engine (untested)
2018-07-10 17:06:17 +08:00
d82beee540
grabber: make parser EOP a pulse
2018-07-10 17:04:07 +08:00
701c93d46c
grabber: add false path constraints
2018-07-10 14:28:23 +08:00
6a77032fa5
grabber: use BUFR/BUFIO
...
Less jitter and frees up BUFGs.
2018-07-10 13:30:38 +08:00
208dc7c218
grabber: prevent glitches in last_x/last_y cdc
2018-07-10 12:56:37 +08:00
c4e3c66265
grabber: add clock constraint
2018-07-10 12:37:32 +08:00
David Nadlinger
768b970deb
Fixup 4359a437 (tuples of lists), add regression tests
2018-07-10 01:18:51 +01:00
David Nadlinger
edc314524c
test_embedding: Remove unused reference to led device
2018-07-10 01:11:47 +01:00
4f56710e4b
grabber: add parser, report detected frame size in core device log
2018-07-10 02:06:37 +08:00
David Nadlinger
4359a43732
compiler: Indirection status of TTuple depends on elements
...
For instance, TTuple(TList(TInt32())) has indirections, while
TTuple(TInt32()) does not.
This fixes memory corruption with RPCs that return tuples of lists.
Signed-off-by: David Nadlinger <code@klickverbot.at>
2018-07-09 18:49:50 +08:00
d2c8e62cb7
test_rtio: relax ClockGeneratorLoopback performance requirements
2018-07-09 18:07:25 +08:00
423929a125
test: relax min transfer rates from 2MB/s to 1.9MB/s
2018-07-09 18:00:24 +08:00
9153c4d8a3
use tokenize.open() to open Python source files
...
Fixes encoding issues especially with device databases modified in obscure editors.
2018-07-07 17:04:56 +08:00
4420046502
kasli_tester: support mixed AD9910/AD9912 systems
2018-07-06 15:43:38 +08:00
ac3f360c26
kasli_tester: fix AD9912 support
2018-07-06 15:43:25 +08:00
509562ddbf
kasli: add WIPM target
2018-07-06 15:41:28 +08:00
4eb26c0050
hmc7043: enable group 5
2018-07-03 14:16:31 +02:00
540bdae99c
grabber: enable DIFF_TERM on inputs
2018-07-01 09:28:51 +08:00
0483b8d14c
sayma_drtio: ditto
2018-06-28 17:03:32 +08:00
04d6ff45c8
kasli_sawgmaster: reset SAWGs
...
Most importantly this resets the phase accumulators.
2018-06-28 17:01:48 +08:00
729ce58f98
sayma: use GTP_CLK1 to clock DRTIO satellite transceiver
...
This is required to get constant skew between the DRTIO transceiver clock
(which then generates the RTIO clock) and the siphaser reference clock.
Both the Si5324 and the RTM clock tree have non-deterministic in-to-out skew
at 150MHz due to dividers.
2018-06-28 11:23:40 +08:00
a65721d649
sayma: put RTM clock tree into the siphaser loop
...
* Fixes one bug where siphaser was one Si5324 output and the rest of the
system was clocked by the other. With the Si5324 settings we have, skew
between the outputs is not controlled.
* Puts the coaxial cable between AMC and RTM into the siphaser loop.
2018-06-27 21:46:55 +08:00
d49716dfac
satman: tune Sayma SYSREF phases
2018-06-27 18:09:35 +08:00
46c044099c
hmc7043,satman: verify alignment of SYSREF slips
2018-06-27 17:36:13 +08:00
7dfd70c502
hmc7043: make margin_{minus,plus} consistent with ad9154
2018-06-27 17:35:26 +08:00
4bbdd43bdf
hmc7043: do not freeze if SYSREF slip fails
2018-06-27 17:32:56 +08:00
a8a2ad68d3
runtime: tune Sayma SYSREF phases
2018-06-27 17:31:29 +08:00
811882943b
artiq_flash: RTM gateware is not required for master variant
2018-06-25 18:28:55 +08:00
c750de2955
sayma: add many-port pure DRTIO master
2018-06-25 18:21:22 +08:00
84b3d9ecc6
bootloader: also check firmware CRC in SDRAM ( #1065 )
2018-06-23 11:28:12 +08:00
68530fde07
sayma: generate 100MHz from Si5324 on standalone and master targets
...
* Allow switching between DRTIO satellite and standalone without
touching the hardware.
* Allow operating standalone and master without an additional RF
signal generator.
2018-06-23 10:44:38 +08:00
whitequark
b6dd9c8bb0
runtime: support builds without RTIO DMA.
...
Fixes #1079 .
2018-06-23 00:56:21 +00:00
whitequark
12fde6d34b
artiq_coremgmt: fix typo.
...
Fixes #1056 .
2018-06-23 00:36:59 +00:00
51a5d8dff9
examples: add Kasli SAWG master
2018-06-22 18:57:49 +08:00
f87da95e57
jesd204: use jesd clock domain for sysref sampler
...
RTIO domain is still in reset during calibration.
2018-06-22 17:13:01 +08:00
76fc63bbf7
jesd204: use separate controls for reset and input buffer disable
2018-06-22 11:38:18 +08:00
d9955fee76
jesd204: make sure IOB FF is used to sample SYSREF at FPGA
2018-06-22 11:00:56 +08:00
60b22217ce
sayma: set DRTIO master HMC830_REF to 100MHz
2018-06-22 10:10:09 +08:00
e6d1726754
sayma: add RTIO log to DRTIO master
2018-06-22 00:05:22 +08:00
83428961ad
sayma: add SAWG and JESD to DRTIO master
2018-06-22 00:04:22 +08:00
c1db02a351
drtio/gth_ultrascale: disable IBUFDS_GTE3 until stable_clkin
...
Precaution against HMC7043 noise issues.
2018-06-21 22:56:07 +08:00
8b3c12e6eb
sayma: clock DRTIO master transceiver from HMC7043
2018-06-21 22:34:44 +08:00
de7d64d482
sayma: clock JESD204 from GTP CLK2
...
This frees up GTP CLK1, which is routable to the SFP quads, for DRTIO.
2018-06-21 22:33:53 +08:00
b28ff587c5
sayma: add sysref sampler to DRTIO master
2018-06-21 22:28:34 +08:00
07bcdfd91e
hmc7043: stricter check of FPGA SYSREF margin
2018-06-21 22:26:49 +08:00
e29536351d
drtio: resync SYSREF when TSC is loaded
2018-06-21 17:00:32 +08:00
5a2a857a2f
firmware: clean up SYSREF phase management
2018-06-21 16:23:41 +08:00
05e908a0fd
hmc7043: align SYSREF with RTIO
2018-06-21 15:54:42 +08:00
9741654cad
hmc7043: style
2018-06-21 15:54:42 +08:00
45e8263208
hmc7043: do not configure phases during initial init
...
They are determined later on.
2018-06-21 15:54:42 +08:00
whitequark
7cc3da4faf
firmware: do not lose the ".dirty" suffix in build versions.
...
Fixes #1074 .
2018-06-21 05:18:51 +00:00
whitequark
095ee28fd9
runtime: fix size values for bytes and bytearray RPCs.
...
Fixes #1076 .
2018-06-21 00:51:56 +00:00
whitequark
9260cdb2e8
compiler: support conversion of list to bytearray and bytes.
...
Fixes #1077 .
2018-06-21 00:40:45 +00:00
5a91f820fd
examples: change Sayma sines frequency to 9MHz
...
Well within Red Pitaya bandwidth.
2018-06-20 22:40:07 +08:00
9288301543
examples: add DRTIO sines
2018-06-20 22:39:40 +08:00
28fb0fd754
sayma: add SYSREF sampler gateware
2018-06-20 17:48:35 +08:00
814d0583db
hmc7043: improve smoothness of sysref phase control
2018-06-20 17:40:48 +08:00
9142a5ab8a
rtio: expose coarse timestamp in RTIO and DRTIO satellite cores
2018-06-20 17:39:54 +08:00
5272c11704
typo
2018-06-20 17:05:20 +08:00
0c32d07e8b
ad9154: new sysref scan
...
Print margins around the pre-defined fixed phase.
Also report error if margins are too small.
The fixed phase is also changed by this commit (the value 88 is
from before the new HMC7043 initialization code, and is probably wrong).
2018-06-20 00:15:58 +08:00
4803ca3799
examples/sayma_drtio: add SAWG channels
2018-06-19 23:50:26 +08:00
3d0e92aefd
hmc7043: check that chip is disabled at startup
2018-06-19 23:49:17 +08:00
740e6863c3
hmc7043: add delay after releasing hardware reset
2018-06-19 23:48:48 +08:00
75b6cea52f
sayma: add SAWG to DRTIO satellite
2018-06-19 19:12:10 +08:00
eb3259b847
firmware: reduce number of DAC initialization attempts
...
Faster startup when one DAC is broken.
2018-06-19 19:10:23 +08:00
1d594d0c97
firmware: make DAC initialization failures non-fatal
...
This allows using RTMs with one broken DAC for development.
2018-06-19 19:09:38 +08:00
158b5e3083
satman: program Allaki
2018-06-19 18:09:05 +08:00
574892a4e5
firmware/serwb: cleanup and improve messaging
2018-06-19 15:11:03 +08:00
c862471165
typo
2018-06-19 14:35:24 +08:00
433273dd95
sayma: support RTM FPGA, HMC830 and HMC7043 in DRTIO master and satellite
2018-06-19 14:33:48 +08:00
476cfa0f53
si5324: improve lock messaging
2018-06-19 14:29:57 +08:00
6403a0d5d1
sayma_amc: update without-sawg description
2018-06-19 13:52:05 +08:00
d29b3dd588
hmc830: compile-time configurable reference frequency
2018-06-19 13:47:32 +08:00
6f3ed81626
targets/sayma_rtm: fix description
2018-06-18 17:46:53 +08:00
21a48711ec
i2c: refactor common operations
2018-06-18 09:34:09 +00:00
0e640a6d6f
hmc7043: fix SYSREF to meet s/h at FPGA ( #794 )
2018-06-18 17:04:12 +08:00
6272052d15
ad9154: don't drive the bsm with txen pins
2018-06-18 10:04:42 +02:00
32484a62de
sayma_amc: remove unused imports
2018-06-17 13:09:44 +02:00
4f0c918dd3
slave_fpga: improve messaging
2018-06-17 00:27:27 +08:00
53ab255c00
sayma_amc: enable slave fpga loading ( #813 )
2018-06-16 12:47:26 +02:00
f9910ab242
i2c: support selecting multiple or no channels
...
closes #1054
2018-06-15 19:36:37 +02:00
40baa8ecba
hmc7043: disable ch 10 and 11 group
2018-06-15 15:34:31 +00:00
edfae3c4ba
hmc7043: make fpga fabric clocks lvds
...
2 V common and 1.9 Vpp swing
is brutal to the banks (HP 1.8V AMC and RT 1.8V RTM)
2018-06-15 14:24:33 +00:00
f385add8b1
slave_fpga: disable cclk and din drive when done
...
to guard against accidental contention (old rtm gateware
but #813 rework done)
2018-06-13 16:26:48 +00:00
1029ac870b
sayma_rtm: don't drive txen pins
...
pins disabled by config
necessary for using that pin as DIN (#813 )
2018-06-13 16:11:30 +00:00
68d16fc292
serwb: support single-ended signals
...
Low-speed PHY only.
2018-06-13 21:28:21 +08:00
a9a25f2605
sayma_rtm: drive ref_lo_clk_sel, and set clk muxes early
2018-06-12 20:00:12 +02:00
aff7fa008f
Revert "artiq_flash/sayma: check for DONE after load"
...
This reverts commit 2de5b0cf25
2018-06-12 19:14:43 +02:00
2de5b0cf25
artiq_flash/sayma: check for DONE after load
2018-06-13 00:47:43 +08:00
Thomas Harty
b90a8fcc82
Merge branch 'master' of https://github.com/m-labs/artiq
2018-06-12 14:55:22 +01:00
ion
28ecf81c6c
Sayma: HMC7043 init and detect no longer need results.
2018-06-12 13:10:26 +01:00
ion
c8935f7adf
Sayma: bypass dividers where possible to minimize noise (nb this changes the output skew).
2018-06-12 12:56:04 +01:00
hartytp
7a0140ecb2
Sayma HMC830: update interface and register writes. ( #1068 )
...
* Break the HMC830 init into separate functions for general purpose (but, integer-N) init, setting dividers and checking lock
* Use 1.6mA ICP (which the loop filter was optimized for)
* Go through the data sheet carefully and set all registers to the correct value (e.g. ensure that all settings are correctly optimized for integer-N usage)
* Change divider values (now using 100MHz PFD, which should give lower noise in theory)
2018-06-12 12:37:17 +01:00
a9d97101fc
slave_fpga: add another check
2018-06-12 10:24:04 +02:00
a143e238a8
savel_fpga: get rid of unneeded config
2018-06-12 10:24:04 +02:00
4912f53ab4
slave_fpga: board_misoc
2018-06-12 10:24:04 +02:00
hartytp
cb6e44b23a
Sayma: disable unused HMC7043 outputs.
2018-06-12 16:18:20 +08:00
0b086225a9
sawg: don't use Cat() for signed signals
...
c.f. #1039 #1040 #1022 #1058 #1044
2018-06-09 07:33:47 +00:00
5b73dd8604
sawg: accurate unittest rtio freq
2018-06-08 17:22:13 +02:00
735e4e8561
pcu: spelling
2018-06-08 14:39:22 +00:00
e5f6750171
sawg: cleanup double assign
2018-06-08 14:31:55 +00:00
Florent Kermarrec
53e9e475d0
serwb: transmit zeroes when nothing to transmit (for prbs), improve rx idle detection
2018-06-08 16:10:31 +02:00
Florent Kermarrec
7296a76f18
serwb: move common datapath code to datapath.py, simplify flow control
2018-06-08 12:37:08 +02:00
Florent Kermarrec
89797d08ed
serwb: revert to 125MHz linerate (until we understand why 1gbps version breaks between builds)
2018-06-07 15:13:56 +02:00
b4c2b148d1
sawg: don't use Mux for signed signals
...
migen#75
2018-06-06 15:51:14 +00:00
Florent Kermarrec
009db5eda9
serwb: revert 1gbps linerate
2018-06-06 16:20:20 +02:00
cae92f9b44
kasli: add Tsinghua variant
2018-06-06 19:03:45 +08:00
38971d130a
comm_analyzer: fix data without any spi reads
...
closes #1050
2018-06-06 12:21:42 +02:00
e21b7965b9
sayma_amc: change test patterns for 'without-sawg'
2018-06-06 08:02:52 +00:00
whitequark
38dac16041
compiler: don't crash when quoting builtin functions.
...
Fixes #1051 .
2018-06-05 23:27:23 +00:00
af88c4c93e
clean up hmc7043 reset
2018-06-05 20:41:48 +08:00
Thomas Harty
988054f4bb
Sayma: fix mistake in HMC7043 init code.
2018-06-05 19:22:04 +08:00
Thomas Harty
bd1ac7cf3b
Configure HMC7043 to give deterministic phase differences between its outputs
2018-06-05 19:22:04 +08:00
Thomas Harty
ac5c4913ec
Sayma RTM: hold hmc7043 in reset/mute state during init.
2018-06-05 19:22:04 +08:00
Florent Kermarrec
b82158a2de
firmware/ad9154: add stpl test
2018-06-05 02:08:57 +02:00
07d4145a35
correct documented siphaser VCO frequency [NFC]
2018-06-04 20:53:43 +08:00
Florent Kermarrec
925b47b077
firmware/ad9154: reset the dac between each configuration attempt
2018-06-04 14:03:26 +02:00
bb87976d4f
suservo: docstring fixes, revert parametrization of r_rtt
2018-06-04 07:27:17 +00:00
07a1425e51
SUservo EEM docs
...
add documentation to eem.SUServo. Change parameterization of t_rtt to include delays on Sampler, as this seems simpler and more robust to changing RTIO frequencies in the future.
c.f. #1046
2018-06-04 08:51:28 +02:00
whitequark
d686d33093
runtime: print hex dumps around PC/EA in case of exception.
...
For #1026 .
2018-06-01 21:17:59 +00:00
whitequark
985fd7377b
artiq_rpctool: use inspect.formatargspec instead of a NIH formatter.
...
Fixes #1029 .
2018-06-01 19:18:14 +00:00
62deffa7d2
opticlock: fix core device name
2018-06-01 15:39:23 +00:00
f50aef1a22
suservo: extract boilerplate
...
closes #1041
2018-06-01 15:37:07 +00:00
5de2d06568
ad53xx/zotino: do not clear power down on overtemp
2018-06-01 13:17:13 +00:00
2c344686d9
ad53xx/zotino: enable overtemp shutdown and readback control
2018-06-01 13:06:52 +00:00
87d3ac9d25
suservo: swap transfer function parametrization
...
The integrator is now parametrized through its gain and not the PI
corner frequency. The integrator gain limit is given in absolute gain
units and not relative to the proportional gain.
close #1033
2018-06-01 09:38:18 +00:00
e408241233
sawg: work around compiler not accepting delay_mu(int32)
2018-06-01 15:42:37 +08:00
f5d55c6902
sawg: add 1 coarse RTIO cycle between spline resets
...
This keeps all events in the same SED lane and limits the number of SED lanes required.
Closes #1038
2018-06-01 15:15:24 +08:00
22506e849f
suservo: clarify timings
...
close #1027
2018-06-01 06:35:38 +00:00
a42f774440
suservo: document offset range limits
...
close #1034
2018-05-31 16:55:44 +00:00
36dcea3edf
suservo: refactor y_mu_to_full_scale as portable
...
close #1032
2018-05-31 16:44:14 +00:00
e136709cac
suservo: document gain state
...
close #1030
2018-05-31 16:36:53 +00:00
5dbdc5650c
suservo: document set_config and get_status more
...
close #1028
2018-05-31 16:32:05 +00:00
e1b0fcc24e
suservo: add documentation on settings and setup
...
close #1015
2018-05-31 16:21:09 +00:00
9b5a46dffd
suservo: fix restart counter assertion
...
c.f. #788
2018-05-31 15:56:11 +00:00
Paweł
44c7a028cb
Added second argument to DIO.add_STD in master and satellite variant of kasli (now builds properly)
2018-05-30 22:49:40 +08:00
8fd57e6ccb
kasli_tester: add Sampler and Zotino support
2018-05-29 22:36:42 +08:00
d1df18ae6a
monkey_patches: work around Python issue 33678. Closes #1016
2018-05-29 17:51:41 +08:00
whitequark
2e09307d8d
firmware: use writeln instead of write in UART logger.
2018-05-29 03:16:52 +00:00
560889372f
firmware: grabber support
2018-05-29 10:26:36 +08:00
b860302a9a
firmware: fix typo in UART logger
2018-05-28 17:25:23 +00:00
whitequark
2b7d98eb04
firmware: enable all log levels when creating UART logger.
...
The default is all off.
2018-05-28 16:49:25 +00:00
ad099edf63
kasli: integrate grabber
2018-05-28 22:43:40 +08:00
563e434e15
eem: finalize grabber support
2018-05-28 22:43:06 +08:00
2612fd1e72
rtio: add grabber deserializer and WIP PHY encapsulation
2018-05-28 22:42:27 +08:00
Florent Kermarrec
e21f14c0b3
serwb/phy: typo (KUSSerdes --> KUSerdes)
2018-05-28 10:41:11 +02:00
c2890c6cf0
kasli_tester: initialize DDS channels
2018-05-28 14:24:39 +08:00
b20a8c86b0
kasli: don't bother with grabber ttls for now
...
not used on target cameras
2018-05-28 07:31:00 +02:00
80c69da17e
eem: add Grabber IOs and CC
2018-05-28 11:16:23 +08:00
4d3f763865
move kasli_opticlock to kasli_basic
2018-05-28 11:02:44 +08:00
cc0ddf9d72
artiq_flash: do not check variants anymore
...
Not very useful and adds to the maintainance when building new Kasli systems.
2018-05-28 10:59:01 +08:00
bb248970df
style
2018-05-28 10:40:05 +08:00
56cfe77c91
environment: spelling
2018-05-27 20:36:11 +02:00
b09d07905c
kasli: add LUH/PTB/HUB variants
...
and refactor/simplify variant selection
2018-05-27 18:33:27 +00:00
whitequark
db4d1878d3
compiler: remove debug print.
2018-05-25 09:37:18 +00:00
whitequark
223b984385
Fix non-exception-safe finally: handlers.
...
Fixes #1013 .
2018-05-25 04:23:32 +00:00
whitequark
fbf2c9a2fb
compiler: hoist loads of kernel invariants to function entry block.
...
Addresses intraprocedural cases of #1007 .
2018-05-25 02:18:13 +00:00
whitequark
12d1b9819c
compiler: handle direct calls to class methods.
...
Fixes #1005 .
2018-05-25 02:02:18 +00:00
Florent Kermarrec
bcb9c3d09d
firmware/serwb: move prbs_test outside of wait_init, add wishbone_test
2018-05-24 16:53:47 +02:00
Florent Kermarrec
bca2969957
sayma_rtm: add RTMScratch module to test remote Wishbone accesses
2018-05-24 16:53:10 +02:00
Florent Kermarrec
7642254d83
Merge branch 'master' of http://github.com/m-labs/artiq
2018-05-24 16:51:23 +02:00
Florent Kermarrec
353767bfdb
firmware/hmc830: add VCO subsystem register 6 programming (suggested by hartytp, tested on hardware without regression)
2018-05-24 16:49:49 +02:00
19efd8b13e
kasli: refactor EEM code
2018-05-24 18:41:54 +08:00
Florent Kermarrec
ad89c42acc
firmware/serwb: automatically adjust prbs test delay to prbs test cycles, increase prbs test cycles
2018-05-24 10:20:55 +02:00
Florent Kermarrec
19e5280824
firmware/ad9154: cleanup DAC init
...
- Split dac_setup in dac_reset, dat_detect & dac_setup.
- Only do one reset/detection.
- Configure before doing SYSREF scan (otherwise scan don't work at the first scan after power up).
- Do the spi_setup in each function.
2018-05-24 09:34:00 +02:00
Florent Kermarrec
fa3b48737b
firmware/hmc830: Added magic word to HMC830 init sequence (from gkasprow & marmeladapk)
2018-05-24 09:23:00 +02:00
9715f774ac
artiq_influxdb: controller (add ping())
2018-05-22 22:12:25 +00:00
whitequark
7aacc04f0c
language: scan functions are not supported on core device.
...
Closes #1009 .
2018-05-22 21:33:35 +00:00
whitequark
b55ce66a1b
Reinstate accidentally removed aqctl_corelog.
...
Closes #1008 .
2018-05-22 21:31:34 +00:00
whitequark
ce3c8fcd3e
compiler: add source location to SSA arguments.
...
Fixes #1006 .
2018-05-22 18:14:14 +00:00
fcd12e3472
suservo: work around #1007
2018-05-22 17:36:41 +00:00
9a86dfe70d
units: add mHz
2018-05-22 17:36:02 +00:00
4e863b32a1
coredevice: configurable initial backing state
...
Several core device drivers maintain a copy of some device state.
Since this copy is not transferred between experiments this backing state
can be different from device state when a new experiment is started.
This commit adds support for injecting initial backing state into
experiments via the device database and sets initial backing state where
known.
ad53xx (zotino): spi2 xfer_duration
novogorny: pgia gains
sampler: pgia gains, spi2 pgia and adc xfer_duration
suservo: pgia gains, spi2 pgia xfer_duration
urukul: cpld cfg (partial: rf_sw), attenuator register
spi2: div/length for xfer_duration
close #1003
2018-05-21 18:55:06 +02:00
4e5fe672e7
kasli: add tester target
2018-05-21 17:43:39 +08:00
2e6b81d59a
kasli_tester: reset core device
2018-05-21 15:35:29 +08:00
8513f0b0d4
minor cleanup
2018-05-21 15:35:00 +08:00
whitequark
9b4ad8b5af
compiler: implement local variable demotion.
2018-05-19 17:05:34 +00:00
whitequark
fd110e9848
compiler: sort predecessors in IR dump output.
...
Makes diffs more useful.
2018-05-19 17:02:08 +00:00
whitequark
dc1c4ebf1d
compiler: use ARTIQ_IR_NO_LOC variable to control IR dump output.
...
Useful e.g. in tests or for running diff on irgen output.
2018-05-19 17:02:08 +00:00
whitequark
21a0f26cd1
compiler: do not emit nonstandard !unconditionally* LLVM metadata.
...
This metadata was added by an LLVM patch that was removed because
it was unsound.
2018-05-19 16:58:03 +00:00
f953bee79e
kasli_test: add RF switch control
2018-05-18 23:48:29 +08:00
f457b59985
kasli_tester: bail out when run from ARTIQ master
2018-05-18 23:30:52 +08:00
3cbcb3bff6
move mitll, sysu and ustc device_dbs to kasli_basic
2018-05-18 23:20:40 +08:00
bdfd993818
kasli_tester: add Urukul support
2018-05-18 23:18:03 +08:00
72aef5799e
kasli/ustc: use TTLOut
2018-05-18 22:55:28 +08:00
9a4408a570
add Kasli TTL tester
2018-05-18 22:52:53 +08:00
b10d3ee4b4
make RTIO clock switch optional and simplify
...
Kasli no longer has an internal RTIO clock.
Switching clocks dynamically is no longer supported.
2018-05-18 17:41:34 +08:00
8a988d0feb
kasli: remove leftover debug print
2018-05-18 17:25:23 +08:00
37bd0c2566
kasli: add USTC target
2018-05-18 16:15:07 +08:00
73f8e61478
kasli_sysu: fix TTL directions in example device_db
2018-05-18 16:13:50 +08:00
6476219296
frontend: fix permissions
2018-05-18 00:10:46 +08:00
bfff755295
urukul: do IO_RST also when blind
2018-05-17 14:48:49 +00:00
whitequark
5744d97d59
firmware: adjust backtrace addresses correctly.
2018-05-17 08:13:55 +00:00
d4f074b1e1
firmware: fix Allaki addressing. Closes #993
2018-05-17 16:02:21 +08:00
whitequark
3b61b7c30b
compiler: fix tests after 4d06c1d8.
2018-05-16 21:53:53 +00:00
whitequark
31c6c79204
firmware: implement an edge profiler.
...
It doesn't work extremely well, and the results can be somewhat
confusing, and it needs a libunwind patch, but it's the best I could
do and it seems still useful.
2018-05-16 21:53:53 +00:00
99f7672c79
ad53xx: tweak spi readback
2018-05-16 19:08:27 +02:00
a640041844
firmware: improve ad9154/hmc830/hmc7043 messaging
2018-05-16 23:15:17 +08:00
fedf7f0c87
firmware/ad9154: cleanup sysref scan and run everytime
2018-05-16 23:01:19 +08:00
1364cd2948
firmware/hmc830_7043: break out HMC830 SPI mode selection
2018-05-16 22:46:45 +08:00
0aadd3a361
firmware/hmc830_7043: improve messaging
2018-05-16 22:46:45 +08:00
whitequark
4d06c1d84b
coredevice.CommKernel: modernize. NFC.
2018-05-16 14:40:14 +00:00
whitequark
ca93b94aea
firmware: move config requests to management protocol.
...
They were only in session protocol because of historical reasons.
2018-05-16 14:32:49 +00:00
whitequark
a39f8d6634
artiq_devtool: use CommMgmt instead of shelling out to artiq_coremgmt.
...
(Which no longer exists.)
This also fixes `artiq_devtool hotswap` to work without
an `artiq_devtool connect` running in background.
2018-05-16 14:08:32 +00:00
whitequark
d446a3293e
frontend: merge core{config,log,boot,debug,profile} into coremgmt.
2018-05-16 14:08:32 +00:00
Florent Kermarrec
f77bcbebb5
serwb/test_serwb_core: fix
2018-05-16 08:34:53 +02:00
Florent Kermarrec
77fc5c599f
serwb/test: update
2018-05-15 23:52:58 +02:00
Florent Kermarrec
3873d09692
serwb: rewrite high-speed phys by splitting clocking/tx/rx, scrambling is now always enabled.
2018-05-15 23:52:41 +02:00
Florent Kermarrec
f8a9dd930b
serwb/genphy: add device parameter (not used here, but this way all the phys share the same parameters), scrambling is also now always enabled.
2018-05-15 23:51:14 +02:00
Florent Kermarrec
2c627cd061
serwb/scrambler: simplify and set scrambler input data to 0 when sink.stb == 0
2018-05-15 23:49:17 +02:00
Florent Kermarrec
7fe49a78d2
firmware/runtime/session: fix compilation when no rtio core
2018-05-15 23:47:47 +02:00
whitequark
8128a814f6
firmware: update dependencies.
2018-05-15 18:17:32 +00:00
whitequark
1b0384c513
firmware: fix satman build.
2018-05-15 16:35:05 +00:00
whitequark
07b713fdad
firmware: use upstream log_buffer.
2018-05-15 15:19:20 +00:00
whitequark
9f5b76253c
firmware: remove some unnecessary unwraps.
2018-05-15 15:05:19 +00:00
whitequark
e5796e26e1
firmware: remove unused #![feature(untagged_unions)].
2018-05-15 15:05:19 +00:00
whitequark
b54926134c
firmware: update the signature of #[lang="panic_fmt"].
2018-05-15 15:05:19 +00:00
Florent Kermarrec
c18a73d45f
sayma_amc/rtm: use new serwb low-speed phy
2018-05-15 16:40:50 +02:00
Florent Kermarrec
913d1e8e12
serwb: add generic low-speed phy (125Mhz linerate, same phy for ultrascale/7-series)
2018-05-15 16:39:39 +02:00
Florent Kermarrec
520aade8fe
serwb/scrambler: cleanup/fix potential bug
2018-05-15 16:30:52 +02:00
whitequark
9347f6e00c
firmware: use a dedicated error type in the scheduler.
...
After this commit, error handling does not normally allocate
(session::Error::{Load,Unexpected} still allocate, but those two
are very rare).
Good riddance to libstd_artiq.
2018-05-15 14:19:44 +00:00
whitequark
479cb9a857
firmware: use dedicated error types for every protocol and thread.
...
Good riddance to io::Error::Unrecognized.
2018-05-15 13:27:23 +00:00
whitequark
514eab3d39
Update Rust to 1.26.0.
2018-05-15 12:47:51 +00:00
whitequark
26faaad2b7
firmware: remove io::Result<T, E> in favor of Result<T, impl Fail>.
...
This doesn't yet use impl Fail since std_artiq::io::Error doesn't
impl it.
2018-05-15 08:29:03 +00:00
whitequark
140ca729aa
firmware: rename io::Error::{UnexpectedEof→UnexpectedEnd}.
...
We don't even have files.
2018-05-15 08:27:45 +00:00
whitequark
ce0593315b
firmware: move {ProtoRead,ProtoWrite} to the root of libio.
2018-05-15 08:16:09 +00:00
whitequark
4416c04ae1
firmware: use the failure crate in libio.
2018-05-15 07:40:13 +00:00
whitequark
9e8f8bb669
firmware: extract io::Cursor into its own file.
...
Also remove unused io::CursorError.
2018-05-15 06:24:04 +00:00
whitequark
a4ab236af3
firmware: simplify some uses.
2018-05-14 19:24:14 +00:00
whitequark
d93aa13fd6
firmware: use upstream compiler_builtins again.
...
I've fixed i128 in LLVM, so there is no need in our fork anymore.
2018-05-14 19:11:57 +00:00
whitequark
5ead27f2e1
firmware: eliminate uses of std_artiq::io::{Read,Write} from runtime.
2018-05-14 19:11:57 +00:00
whitequark
cf33ba748d
firmware: eliminate non-io uses of std_artiq from runtime.
...
Just replace these with references to alloc.
2018-05-14 19:11:57 +00:00
a100c73dfe
suservo: support pure-I
2018-05-14 18:48:27 +00:00
whitequark
ae50196186
firmware: rename libproto to libproto_artiq.
...
libproto_artiq only has ARTIQ-specific protocols.
2018-05-14 18:09:44 +00:00
whitequark
02b8426f60
firmware: rename libboard to libboard_misoc.
...
By analogy with libbuild_misoc. Hopefully one day it actually gets
moved to misoc...
2018-05-14 18:09:44 +00:00
whitequark
1ff42683d9
firmware: merge libamp into libboard_artiq.
...
All gateware interfaces live in libboard_artiq, but libamp predates
libboard_artiq.
2018-05-14 17:33:25 +00:00
whitequark
764386c9e3
firmware: split libdrtioaux into libproto and libboard_artiq modules.
...
All other protocol code lives in libproto, and all other gateware
interfaces live in libboard_artiq.
2018-05-14 17:26:59 +00:00
whitequark
6a10d54432
firmware: migrate rpc_proto to new libio.
...
This closes an old and horrible issue in that some code in ksupport
may implicitly try to allocate and we'll never know until it crashes
at runtime inside liballoc_stub.
This also removes liballoc_stub.
This also removes ReadExt and WriteExt from libproto.
Hooray!
2018-05-14 17:26:59 +00:00
whitequark
9a1bd66d2c
compiler: add test for int64(round(1.0)).
2018-05-14 15:57:27 +00:00
e121a81f21
ad9914: fix frequency_to_xftw and xftw_to_frequency
2018-05-14 23:49:00 +08:00
80df86f700
ad9914: set_mu_x -> set_x_mu
2018-05-14 23:49:00 +08:00
whitequark
09617c9f5e
firmware: migrate session_proto to new libio.
2018-05-14 15:17:32 +00:00
whitequark
e9c88e32e6
firmware: migrate moninj_proto to new libio.
2018-05-14 15:17:32 +00:00
whitequark
e292c8ab65
firmware: migrate mgmt_proto to new libio.
2018-05-14 15:17:32 +00:00
0c1caf0744
suservo: clean up and beautify example
2018-05-14 15:22:47 +02:00
4ddb29fa02
suservo: document class arguments
2018-05-14 15:22:47 +02:00
whitequark
976bb5e935
firmware: migrate analyzer_proto to new libio.
2018-05-14 12:51:59 +00:00
whitequark
2999756493
firmware: impl std_artiq::io::{Read,Write} for io::{Read,Write}.
2018-05-14 12:51:59 +00:00
whitequark
bfc8fd0807
firmware: add io::Error::Unrecognized variant and use it in drtioaux.
2018-05-14 12:51:59 +00:00
504d37b66b
suservo: add SI units functions and document
...
m-labs/artiq#788
2018-05-14 12:26:49 +00:00
4993ceec35
sampler: unroll conversion for speed
2018-05-14 12:26:49 +00:00
d71e4e60a9
suservo: use addition for offset
2018-05-14 12:26:49 +00:00
27f975e7bb
kasli: eem DifferentialInputs need DIFF_TERM
...
cleanup some formatting on the way
2018-05-14 12:26:49 +00:00
2a47b934ea
suservo: remove adc return clock gating
2018-05-14 12:26:49 +00:00
74c0b4452b
suservo: clkout and sdo[b-d] are inverted
2018-05-14 12:26:49 +00:00
04240cdc08
suservo: sampler channels are reversed
2018-05-14 12:25:09 +00:00
whitequark
7e299563df
firmware: mark many functions in libio as #[inline].
2018-05-14 11:22:56 +00:00
whitequark
368d6f9bfb
satman: remove useless _Unwind_Resume.
2018-05-14 11:22:56 +00:00
whitequark
42420e094a
satman: don't unwrap so much in process_aux_packet.
...
This shrinks the code by almost 4K.
2018-05-14 11:22:56 +00:00
ba1d137d19
ad9914: fix FTW write in regular resolution mode
2018-05-14 18:47:23 +08:00
whitequark
56a29b91fc
firmware: implement ConsoleLogger, use it in satman.
2018-05-14 10:45:11 +00:00
whitequark
5d43d457d2
satman: eliminate heap.
2018-05-14 10:05:02 +00:00
whitequark
46c8afc56c
firmware: implement libio and use in in drtioaux.
2018-05-14 10:02:39 +00:00
whitequark
d543c9aa63
firmware: backtrace_artiq → unwind_backtrace.
...
This crate isn't ARTIQ-specific.
2018-05-14 07:33:00 +00:00
b04c7abde8
ad9914: fix kernel_invariants
2018-05-14 14:02:11 +08:00
56a18682a7
ad9914: minor fixes
2018-05-14 10:37:50 +08:00
194d6462ee
ad9914: fix set_mu
2018-05-14 00:19:09 +08:00
hartytp
00cb31b804
sampler: remove v_ref parameter ( #988 )
2018-05-13 18:00:57 +02:00
3027951dd8
integrate new AD9914 driver
...
moninj, analyzer, docs, examples, tests.
2018-05-13 23:29:35 +08:00
663d8e66ba
ad9914: optimize extended-resolution mode
2018-05-13 23:01:06 +08:00
c8d91b297d
coredevice: add new ad9914 driver
2018-05-13 22:30:33 +08:00
whitequark
f383a470fe
satman: do not debug print unexpected aux packets.
...
This shrinks firmware by 2.8K.
2018-05-13 13:43:39 +00:00
whitequark
aa42a69849
libdrtioaux: always inline read/write helpers.
...
This shrinks Packet::{read_from,write_to} by 1K.
2018-05-13 13:39:14 +00:00
whitequark
32522be413
satman: use 1K log buffer and 4K stack.
...
This reduces memory requirements in half.
2018-05-13 13:28:00 +00:00
whitequark
ee4c475cf3
gateware: fix Sayma satellite build.
...
RTIO clock multiplier was removed from Sayma in 32f22f4c
2018-05-13 13:10:39 +00:00
8c1390e557
kasli: use 62.5MHz clock for siphaser reference ( #999 )
2018-05-12 22:58:03 +08:00
2426fea3f2
siphaser: support external reference for the freerunning 150MHz
2018-05-12 22:57:11 +08:00
6796413a53
serwb: remove unnecessary shebang line
2018-05-12 22:49:44 +08:00
Florent Kermarrec
f5208ff2f3
serwb/core: reduce buffering, use buffered=True
2018-05-12 12:03:58 +02:00
Florent Kermarrec
fdc953e569
serwb/etherbone: recuce buffering
2018-05-12 12:03:11 +02:00
Florent Kermarrec
6e67e6d0b1
serwb: revert some changes (was breaking simulation)
2018-05-12 11:59:46 +02:00
Florent Kermarrec
0a6d4ccd85
serwb/phy: improve/cleanup init
2018-05-12 01:35:34 +02:00
Florent Kermarrec
b6ab59fb80
serwb/phy: increase timeout
2018-05-12 01:32:55 +02:00
Florent Kermarrec
e09dbc89bc
serwb: remove idelaye3 en_vtc (was not done correctly, we'll add direct software control)
2018-05-12 01:32:16 +02:00
Florent Kermarrec
6b4bbe31f7
firmware/ad9154: use fixed hmc7043 sysref phase (found with scan)
2018-05-12 00:12:59 +02:00
Florent Kermarrec
3c49eba0a0
firmware/hmc830_7043: put hmc7043 in sleep mode before hmc830 initialization
...
hmc7043 seems to generate broadband noise when not initialized. This allows isolating issues. If hmc830 still does not always lock correctly, then this is not related to hmc7043 broadband noise.
2018-05-12 00:06:49 +02:00
Florent Kermarrec
cd4477864a
serwb: fix case when rtm fpga is not loaded, lvds input can be 0 or 1
2018-05-11 23:31:25 +02:00
2e3bf8602f
serwb: reduce buffering. Closes #997
2018-05-11 14:13:41 +08:00
2cece47b10
firmware/si5324: fix compilation warning
2018-05-09 20:00:08 +08:00
6b811c1a8b
sayma: fix runtime/rtm gateware address conflict
2018-05-09 19:47:29 +08:00
Florent Kermarrec
9de08f85c6
firmware/ad9154: reduce verbosity of dac_sysref_cfg
2018-05-09 10:57:00 +02:00
f055bf88f6
suservo: add clip flags ( #992 )
2018-05-09 07:16:15 +00:00
Florent Kermarrec
60fd362d57
serwb: fix rx_comma detection
2018-05-07 23:54:35 +02:00
7d4a103a43
opticlock, suservo: set default kasli hw_rev
2018-05-07 09:07:18 +02:00
whitequark
c646409dbe
firmware: fix order of bits clocked into hmc542.
...
Fixes #993 .
2018-05-05 03:12:25 +00:00
whitequark
917a4185eb
Unbreak 9dc7efef.
2018-05-05 03:00:30 +00:00
whitequark
fd2b8d5f8f
firmware: raise hmc542 log level to INFO.
2018-05-05 02:59:49 +00:00
whitequark
a148729bf8
artiq_flash, artiq_devtool: add support for ssh -J option.
2018-05-05 02:50:01 +00:00
whitequark
9704fb837f
firmware: fix warnings in ad9154 driver.
2018-05-05 01:55:42 +00:00
whitequark
8a70c18d1e
firmware: add debug output to hmc542 driver.
2018-05-05 01:53:30 +00:00
whitequark
68ef09ed73
firmware: stop profiler before rebooting too.
2018-05-05 01:52:44 +00:00
whitequark
9dc7efefe4
compiler: transparently handle Windows newlines in RunTool.
2018-05-05 01:43:00 +00:00
whitequark
4f29d9134f
firmware: update log_buffer.
...
Fixes #986 .
2018-05-05 01:18:59 +00:00
whitequark
5ebc626cf4
artiq_coreprofile: fix an inverted option.
2018-05-05 00:49:42 +00:00
whitequark
b1d349cc1b
firmware: implement a sampling profiler.
...
Does not yet support constructing call graphs.
2018-05-05 00:44:40 +00:00
whitequark
9857dfcd7d
firmware: add irq::Exception to libboard.
2018-05-04 18:41:03 +00:00
0b4d06c7a9
worker: keep sys.modules untouched until the end of examine()
2018-05-02 12:50:37 +08:00
8079aa6d20
worker: python docs recommend not replacing sys.modules
2018-05-02 12:48:50 +08:00
8c69d939fb
worker: restore sys.modules in examine() ( #976 )
2018-05-02 12:32:35 +08:00
8d66d53e06
Revert "tools/file_import: restore sys.modules. Closes #976 "
...
This reverts commit b48e782dd6
2018-05-02 12:14:56 +08:00
5f0cfadb30
rtio/sed: add unittest for sequence number rollover
2018-05-02 12:04:30 +08:00
4120105e3a
rtio/sed: fix output network cmp_wrap
2018-05-02 12:04:03 +08:00
bce8fa3ec5
rtio/sed: add replace unittest at the top level ( #978 )
2018-05-02 10:58:18 +08:00
83fb431cd0
rtio/sed: pass sequence numbers through the FIFOs. Closes #978
2018-05-02 10:57:57 +08:00
Florent Kermarrec
05955bfd79
sayma_rtm: use bufio for sys4x (needed since we are using a -1 speedgrade)
2018-05-01 22:16:35 +02:00
b48e782dd6
tools/file_import: restore sys.modules. Closes #976
2018-05-01 22:15:47 +08:00
Florent Kermarrec
84e1f05559
sayma_rtm: make cd_sys4x clock domain reset_less
2018-05-01 16:11:26 +02:00
whitequark
623614f835
Update LLVM to 6.0.0 and Rust to 1.25.0.
2018-05-01 08:57:37 +00:00
Florent Kermarrec
64c8eee28d
serwb/phy/master: fix slave ready detection by filtering possible glitches on rx data (seems to happen when RTM fpga is not loaded)
2018-04-30 23:59:56 +02:00
5a683ddd1f
Revert "kasli: force hw_rev for the different targets"
...
This reverts commit 17d7d7856a
2018-04-28 23:24:41 +02:00
17d7d7856a
kasli: force hw_rev for the different targets
2018-04-28 21:30:29 +02:00
whitequark
f7e08ec46b
Unbreak f35f1001.
2018-04-28 01:03:08 +00:00
whitequark
f35f100110
compiler: don't crash printing locations of specialized functions.
...
Fixes #987 .
2018-04-28 00:49:25 +00:00
8812824fb2
suservo: speed up example, interlock mem
2018-04-27 17:17:17 +00:00
ae80bab180
urukul: reg based io-update is a kernel
2018-04-27 16:42:09 +00:00
5d3c76fd50
sayma_rtm: use bitstream opts in migen
2018-04-27 15:43:32 +00:00
5f00326c65
suservo: coeff mem write port READ_FIRST
2018-04-27 15:43:32 +00:00
73fa572275
suservo: documentation, small API changes
2018-04-27 16:53:22 +02:00
Florent Kermarrec
4e2d9abaf7
firmware/ad9154: combine analog and digital delay of hmc7043 for sysref scan
2018-04-27 14:32:03 +02:00
fe9834bac4
suservo: update 'technology preview' example [wip]
...
Still with mostly undocumented and unstable API.
2018-04-27 12:04:17 +00:00
307cd07b9d
suservo: lots of gateware/ runtime changes
...
tested/validated:
* servo enable/disable
* dds interface, timing, io_update, mask_nu
* channel control (en_out, en_iir, profile)
* profile configuration (coefficients, delays, offsets, channel)
* adc timings and waveforms measured
* asf state readback
* adc readback
individual changes below:
suservo: correct rtio readback
suservo: example, device_db [wip]
suservo: change rtio channel layout
suservo: mem ports in rio domain
suservo: sck clocked from rio_phy
suservo: cleanup, straighten out timing
suservo: dds cs polarity
suservo: simplify pipeline
suservo: drop unused eem names
suservo: decouple adc SR from IIR
suservo: expand coredevice layer
suservo: start the correct stage
suservo: actually load ctrl
suservo: refactor/tweak adc timing
suservo: implement cpld and dds init
2018-04-27 13:50:26 +02:00
01f762a8f5
urukul/ad9910: support blind init
...
urukul: always set io_update attribute
to silence compiler warning w.r.t. kernel_invariants
2018-04-27 13:48:40 +02:00
Florent Kermarrec
3802c7badb
firmware/ad9154: add sysref scan/conf for jesd sc1
2018-04-27 13:20:20 +02:00
Florent Kermarrec
8212e46f5e
sayma_amc: filter jesd refclk/sysref with jreset (hmc7043 can generate noise when unconfigured see sinara issue #541 )
2018-04-27 13:04:37 +02:00
edbc7763e0
urukul: allow no io_update_device
2018-04-25 17:32:36 +00:00
8a1151b54f
suservo: example device db
2018-04-25 17:14:25 +00:00
f9b2c32739
suservo: add pgia spi channel
2018-04-25 17:14:25 +00:00
c83305065a
suservo: add servo/config/status register
2018-04-25 15:59:06 +00:00
105068ad90
suservo: fix restart timing
2018-04-25 15:19:49 +00:00
c304b6207a
suservo: drop adc idelays
2018-04-25 14:59:50 +00:00
b44d6517d1
suservo: use 125 MHz SDR ADC
...
* easier timing
* natural sampling on rising edge
* timing, signal robustness
* adjust the servo iteration timing
2018-04-25 14:32:23 +00:00
37c186a0fc
suservo: refactor, constrain
...
* remove DiffMixin, move pad layout handling to pads
* add input delay constraints, IDELAYs
2018-04-25 13:44:52 +00:00
d0258b9b2d
suservo: set input delays
2018-04-24 15:30:25 +00:00
fe75064c1e
suservo: cleanup rtio interface
2018-04-24 13:08:40 +00:00
3942c2d274
suservo: fix clkout cd drive
2018-04-24 10:18:32 +00:00
f74998a5e0
suservo: move arch logic to top, fix tests
2018-04-23 21:11:26 +00:00
4903eb074c
suservo: use BUFIO/BUFH for ADC
2018-04-23 18:30:19 +00:00
e36deab0a8
suservo/adc: try to help vivado extract srls
2018-04-23 18:30:19 +00:00
929ed4471b
kasli/SUServo: use suservo, implement urukul_qspi
...
m-labs/artiq#788
2018-04-23 18:30:18 +00:00
4c1e356f67
suservo: add pads rewiring layer for eems
2018-04-23 18:30:18 +00:00
99dd9c7a2a
suservo: fix rtio interface width
2018-04-23 18:30:18 +00:00
d5eea962ec
suservo: fix cnv_b diff
2018-04-23 18:30:12 +00:00
c8fd63754a
suservo: add unittests
...
m-labs/artiq#788
2018-04-23 18:25:59 +00:00
934c41b90a
gateware: add suservo
...
from
fe4b60b902m-labs/artiq#788
2018-04-23 18:24:59 +00:00
4fe09fddd5
examples/kc705_nist_clock: update to new ad53xx driver
2018-04-22 15:03:30 +08:00
c47d3ec8c8
zotino: use None as default for ldac and clr
...
This is also what AD53xx does.
2018-04-22 15:03:01 +08:00
d2d02ae353
artiq_coredebug: fix permissions
2018-04-22 15:02:17 +08:00
whitequark
3b054855ec
firmware: add allocator debug feature, invoked by artiq_coredebug frontend.
2018-04-21 19:39:46 +00:00
whitequark
873324d52b
firmware: don't truncate queued RPCs ( fixes #985 ).
2018-04-21 19:39:46 +00:00
whitequark
58967f14fd
compiler: do not try to re-coerce fully coerced numerics.
2018-04-21 18:25:52 +00:00
whitequark
742e273441
Commit missing part of b4e3c30d.
2018-04-20 15:27:27 +00:00
whitequark
0d5fd1e83d
runtime: fix race condition in log extraction code paths ( #979 ).
...
The core device used to panic if certain combinations of borrows
of the log buffer happened. Now they all use .try_borrow_mut().
2018-04-20 15:26:00 +00:00
whitequark
b4e3c30d8c
compiler: desugar x != y into not x == y ( fixes #974 ).
2018-04-20 12:20:45 +00:00
Florent Kermarrec
fe689ab4f2
firmware/serwb: add link test, use info! instead of debug! for link settings (useful to analyze logs from others boards)
2018-04-17 19:24:22 +02:00
Florent Kermarrec
439d2bf2bc
sayma/serwb: adapt, full reset of rtm on link reset
2018-04-17 19:24:03 +02:00
Florent Kermarrec
8edf4541d6
serwb: adapt test
2018-04-17 19:21:53 +02:00
