forked from M-Labs/artiq
1
0
Fork 0

Revert "Globally update UART baudrate to 921600."

This reverts commit b29e2d5bfe.

This broke flterm firmware upload, which was the entire point
of the whole exercise.
This commit is contained in:
whitequark 2017-01-25 00:29:37 +00:00
parent 6414e40deb
commit de17908b38
7 changed files with 4 additions and 9 deletions

View File

@ -100,7 +100,7 @@ def main():
logger.info("Booting runtime")
flterm = run_command(
"{env} python3 flterm.py {serial} --speed 921600" +
"{env} python3 flterm.py {serial} " +
"--kernel /tmp/{tmp}/runtime.bin " +
("--upload-only" if action == "boot" else "--output-only"))
artiq_flash = run_command(
@ -151,7 +151,7 @@ def main():
logger.info("Connecting to device")
flterm = run_command(
"{env} python3 flterm.py {serial} --speed 921600 --output-only")
"{env} python3 flterm.py {serial} --output-only")
drain(flterm)
else:

View File

@ -112,7 +112,6 @@ class _NIST_Ions(MiniSoC, AMPSoC):
sdram_controller_type="minicon",
l2_size=128*1024,
ident=artiq_version,
uart_baudrate=921600,
**kwargs)
AMPSoC.__init__(self)
if isinstance(self.platform.toolchain, XilinxVivadoToolchain):

View File

@ -33,7 +33,6 @@ class Master(MiniSoC, AMPSoC):
sdram_controller_type="minicon",
l2_size=128*1024,
ident=artiq_version,
uart_baudrate=921600,
**kwargs)
AMPSoC.__init__(self)

View File

@ -131,7 +131,6 @@ class Satellite(BaseSoC):
sdram_controller_type="minicon",
l2_size=128*1024,
ident=artiq_version,
uart_baudrate=921600,
**kwargs)
platform = self.platform

View File

@ -169,7 +169,6 @@ class Phaser(MiniSoC, AMPSoC):
sdram_controller_type="minicon",
l2_size=128*1024,
ident=artiq_version,
uart_baudrate=921600,
**kwargs)
AMPSoC.__init__(self)
self.platform.toolchain.bitstream_commands.extend([

View File

@ -160,7 +160,6 @@ class Demo(BaseSoC, AMPSoC):
l2_size=64*1024,
ident=artiq_version,
clk_freq=75*1000*1000,
uart_baudrate=921600,
**kwargs)
AMPSoC.__init__(self)

View File

@ -187,7 +187,7 @@ These steps are required to generate gateware bitstream (``.bit``) files, build
* Check that the board boots by running a serial terminal program (you may need to press its FPGA reconfiguration button or power-cycle it to load the gateware bitstream that was newly written into the flash): ::
$ flterm /dev/ttyUSB1 --speed 921600
$ flterm /dev/ttyUSB1
MiSoC BIOS http://m-labs.hk
[...]
Booting from flash...
@ -197,7 +197,7 @@ These steps are required to generate gateware bitstream (``.bit``) files, build
.. note:: flterm is part of MiSoC. If you installed MiSoC with ``setup.py develop --user``, the flterm launcher is in ``~/.local/bin``.
The communication parameters are 921600 8-N-1. Ensure that your user has access
The communication parameters are 115200 8-N-1. Ensure that your user has access
to the serial device (``sudo adduser $USER dialout`` assuming standard setup).
.. _installing-the-host-side-software: