forked from M-Labs/artiq
1
0
Fork 0

manual: document startup clock and kernel

This commit is contained in:
Sebastien Bourdeauducq 2015-11-01 00:24:44 +08:00
parent a2c074cc33
commit 73fed53c09
2 changed files with 20 additions and 9 deletions

View File

@ -323,7 +323,7 @@ Installing the host-side software
Configuring the core device
---------------------------
This should be done after either installation methods (conda or source).
This should be done after either installation method (conda or source).
.. _flash-mac-ip-addr:
@ -371,16 +371,16 @@ This should be done after either installation methods (conda or source).
.. note:: The reset button of the KC705 board is the "CPU_RST" labeled button.
.. warning:: Both those instructions will result in the flash storage being wiped out. However you can use the test mode to change the IP/MAC without erasing everything if you skip the "fserase" command.
* (optional) Flash the ``idle`` kernel
* (optional) Flash the idle kernel
The ``idle`` kernel is the kernel (some piece of code running on the core device) which the core device runs whenever it is not connected to a PC via ethernet.
The idle kernel is the kernel (some piece of code running on the core device) which the core device runs whenever it is not connected to a PC via ethernet.
This kernel is therefore stored in the :ref:`core device configuration flash storage <core-device-flash-storage>`.
To flash the ``idle`` kernel:
To flash the idle kernel:
* Compile the ``idle`` experiment:
The ``idle`` experiment's ``run()`` method must be a kernel: it must be decorated with the ``@kernel`` decorator (see :ref:`next topic <connecting-to-the-core-device>` for more information about kernels).
* Compile the idle experiment:
The idle experiment's ``run()`` method must be a kernel: it must be decorated with the ``@kernel`` decorator (see :ref:`next topic <connecting-to-the-core-device>` for more information about kernels).
Since the core device is not connected to the PC, RPCs (calling Python code running on the PC from the kernel) are forbidden in the ``idle`` experiment.
Since the core device is not connected to the PC, RPCs (calling Python code running on the PC from the kernel) are forbidden in the idle experiment.
::
$ artiq_compile idle.py
@ -391,6 +391,17 @@ To flash the ``idle`` kernel:
.. note:: You can find more information about how to use the ``artiq_coretool`` utility on the :ref:`Utilities <core-device-access-tool>` page.
* (optional) Flash the startup kernel
The startup kernel is executed once when the core device powers up. It should initialize DDSes, set up TTL directions, etc. Proceed as with the idle kernel, but using the ``startup_kernel`` key in ``artiq_coretool``.
* (optional) Select the startup clock
The core device may use either an external clock signal or its internal clock. This clock can be switched dynamically after the PC is connected using the ``external_clock`` parameter of the core device driver; however, one may want to select the clock at power-up so that it is used for the startup and idle kernels. Use one of these commands: ::
$ artiq_coretool cfg-write -s startup_clock i # internal clock (default)
$ artiq_coretool cfg-write -s startup_clock e # external clock
Ubuntu 14.04 specific instructions
----------------------------------

View File

@ -104,7 +104,7 @@ The artiq_coretool utility allows to perform maintenance on the core device:
* as well as read, write and remove key-value records from the :ref:`core-device-flash-storage`;
* erase the entire flash storage area.
To use this tool, you need to specify a ``device_db.pyon`` device database file which contains a ``comm`` device (an example is provided in ``artiq/examples/master/device_db.pyon``). This tells the tool how to connect to the core device (via serial or via TCP) and with which parameters (baudrate, serial device, IP address, TCP port). When not specified, the artiq_coretool utility will assume that there is a file named ``device_db.pyon`` in the current directory.
To use this tool, you need to specify a ``device_db.pyon`` device database file which contains a ``comm`` device (an example is provided in ``examples/master/device_db.pyon``). This tells the tool how to connect to the core device (via serial or via TCP) and with which parameters (baudrate, serial device, IP address, TCP port). When not specified, the artiq_coretool utility will assume that there is a file named ``device_db.pyon`` in the current directory.
To read the record whose key is ``mac``::
@ -117,7 +117,7 @@ To write the value ``test_value`` in the key ``my_key``::
$ artiq_coretool cfg-read my_key
b'test_value'
You can also write entire files in a record using the ``-f`` parameter. This is useful for instance to write the ``idle`` kernel in the flash storage::
You can also write entire files in a record using the ``-f`` parameter. This is useful for instance to write the startup and idle kernels in the flash storage::
$ artiq_coretool cfg-write -f idle_kernel idle.elf
$ artiq_coretool cfg-read idle_kernel | head -c9