firmware: support DDRPHY without write leveling (fixes #886).

Currently, this is kasli.

artiq/firmware/bootloader/main.rs

@@ -158,6 +158,7 @@ fn network_boot() {
 
     println!("Using MAC address {} and IP address {}", eth_addr, ip_addr);
 
+    #[allow(unused_mut)]
     let mut net_device = unsafe { ethmac::EthernetDevice::new() };
 
     #[cfg(has_ethphy)]

artiq/firmware/libboard/sdram.rs

@@ -8,13 +8,6 @@ mod ddr {
                     DFII_COMMAND_WRDATA, DFII_COMMAND_RDDATA};
     use sdram_phy::{DFII_NPHASES, DFII_PIX_DATA_SIZE, DFII_PIX_WRDATA_ADDR, DFII_PIX_RDDATA_ADDR};
 
-    unsafe fn enable_write_leveling(enabled: bool) {
-        dfii::pi0_address_write(sdram_phy::DDR3_MR1 as u16 | ((enabled as u16) << 7));
-        dfii::pi0_baddress_write(1);
-        sdram_phy::command_p0(DFII_COMMAND_RAS|DFII_COMMAND_CAS|DFII_COMMAND_WE|DFII_COMMAND_CS);
-        ddrphy::wlevel_en_write(enabled as u8);
-    }
-
     #[cfg(kusddrphy)]
     const DDRPHY_MAX_DELAY: u16 = 512;
     #[cfg(not(kusddrphy))]
@@ -30,6 +23,15 @@ mod ddr {
         )
     }
 
+    #[cfg(ddrphy_wlevel)]
+    unsafe fn enable_write_leveling(enabled: bool) {
+        dfii::pi0_address_write(sdram_phy::DDR3_MR1 as u16 | ((enabled as u16) << 7));
+        dfii::pi0_baddress_write(1);
+        sdram_phy::command_p0(DFII_COMMAND_RAS|DFII_COMMAND_CAS|DFII_COMMAND_WE|DFII_COMMAND_CS);
+        ddrphy::wlevel_en_write(enabled as u8);
+    }
+
+    #[cfg(ddrphy_wlevel)]
     unsafe fn write_level(logger: &mut Option<&mut fmt::Write>,
                           delay: &mut [u16; DQS_SIGNAL_COUNT],
                           high_skew: &mut [bool; DQS_SIGNAL_COUNT]) -> bool {
@@ -102,6 +104,7 @@ mod ddr {
         !failed
     }
 
+    #[cfg(ddrphy_wlevel)]
     unsafe fn read_bitslip(logger: &mut Option<&mut fmt::Write>,
                            delay: &[u16; DQS_SIGNAL_COUNT],
                            high_skew: &[bool; DQS_SIGNAL_COUNT]) {
@@ -238,13 +241,16 @@ mod ddr {
     }
 
     pub unsafe fn level(logger: &mut Option<&mut fmt::Write>) -> bool {
-        let mut delay = [0; DQS_SIGNAL_COUNT];
+        #[cfg(ddrphy_wlevel)]
-        let mut high_skew = [false; DQS_SIGNAL_COUNT];
+        {
-
+            let mut delay = [0; DQS_SIGNAL_COUNT];
-        if !write_level(logger, &mut delay, &mut high_skew) {
+            let mut high_skew = [false; DQS_SIGNAL_COUNT];
-            return false
+            if !write_level(logger, &mut delay, &mut high_skew) {
+                return false
+            }
+            read_bitslip(logger, &delay, &high_skew);
         }
-        read_bitslip(logger, &delay, &high_skew);
+
         read_delays(logger);
 
         true

artiq/firmware/runtime/main.rs

@@ -148,7 +148,7 @@ fn startup_ethernet() {
         }
     }
 
-    let mut net_device = unsafe { ethmac::EthernetDevice::new() };
+    let net_device = unsafe { ethmac::EthernetDevice::new() };
 
     // fn _net_trace_writer<U>(timestamp: u64, printer: smoltcp::wire::PrettyPrinter<U>)
     //         where U: smoltcp::wire::pretty_print::PrettyPrint {

conda/artiq-dev/meta.yaml

@@ -15,7 +15,7 @@ requirements:
     - python >=3.5.3,<3.6
     - setuptools 33.1.1
     - migen 0.6.dev py35_61+git31c446b
-    - misoc 0.8.dev py35_52+gitddbf9cbd
+    - misoc 0.8.dev py35_57+git3bfb128a
     - jesd204b 0.4
     - microscope
     - binutils-or1k-linux >=2.27