forked from M-Labs/artiq
1
0
Fork 0

Shuttler: Correct spelling and grammar in docs

This commit is contained in:
linuswck 2023-09-26 15:12:29 +08:00 committed by Sébastien Bourdeauducq
parent ab0d4c41c3
commit 0c1b572872
1 changed files with 8 additions and 8 deletions

View File

@ -21,7 +21,7 @@ class Config:
The configuration registers control waveform phase auto-clear, and pre-DAC
gain & offset values for calibration with ADC on the Shuttler AFE card.
To find the calibrated DAC code, the Shuttler core first multiplies the
To find the calibrated DAC code, the Shuttler Core first multiplies the
output data with pre-DAC gain, then adds the offset.
.. note::
@ -49,7 +49,7 @@ class Config:
"""Set/Unset waveform phase clear bits.
Each bit corresponds to a Shuttler waveform generator core. Setting a
clear bit forces the Shuttler core to clear the phase accumulator on
clear bit forces the Shuttler Core to clear the phase accumulator on
waveform trigger (See :class:`Trigger` for the trigger method).
Otherwise, the phase accumulator increments from its original value.
@ -156,7 +156,7 @@ class Volt:
and 46 bits in width respectively. See :meth:`shuttler_volt_to_mu` for
machine unit conversion.
Note: The waveform is not updated to the Shuttler core until
Note: The waveform is not updated to the Shuttler Core until
triggered. See :class:`Trigger` for the update triggering mechanism.
:param a0: The :math:`a_0` coefficient in machine unit.
@ -243,7 +243,7 @@ class Dds:
machine unit conversion. :math:`c_0`, :math:`c_1` and :math:`c_2` are
16, 32 and 32 bits in width respectively.
Note: The waveform is not updated to the Shuttler core until
Note: The waveform is not updated to the Shuttler Core until
triggered. See :class:`Trigger` for the update triggering mechanism.
:param b0: The :math:`b_0` coefficient in machine unit.
@ -291,11 +291,11 @@ class Trigger:
@kernel
def trigger(self, trig_out):
"""Triggers coefficient update of (a) Shuttler core channel(s).
"""Triggers coefficient update of (a) Shuttler Core channel(s).
Each bit corresponds to a Shuttler waveform generator core. Setting
`trig_out` bits commits the pending coefficient update (from
`set_waveform` in :class:`Volt` and :class:`Dds`) to the Shuttler core
`set_waveform` in :class:`Volt` and :class:`Dds`) to the Shuttler Core
synchronously.
:param trig_out: Coefficient update trigger bits. The MSB corresponds
@ -410,7 +410,7 @@ class ADC:
contents.
.. note::
The datasheet only requires 64 cycles, but reaserting `CS_n` right
The datasheet only requires 64 cycles, but reasserting `CS_n` right
after the transfer appears to interrupt the start-up sequence.
"""
self.bus.set_config_mu(ADC_SPI_CONFIG, 32, SPIT_ADC_WR, CS_ADC)
@ -584,7 +584,7 @@ class ADC:
:param volts: A list of all 16 cubic DC-bias spline.
(See :class:`Volt`)
:param trigger: The Shuttler spline coefficient update trigger.
:param config: The Shuttler core configuration registers.
:param config: The Shuttler Core configuration registers.
:param samples: A list of sample voltages for calibration. There must
be at least 2 samples to perform slope rate calculation.
"""