# Build and test firmware ## Operating hints and warnings * 😡 **Always** use grounding strap during dis/assembly or other cards' physical operation * 😡 **Always** power off devices before un/plugging * 🧐 If needed to power-cycle the crate, wait at least 30 seconds before turning them on * 🙅 Avoid the boards touching conductive materials - wires, metals. Use at least plastic ESD bags if you need the cards to be put at the desk or any other surface. * 💁 Be gentle to the EEM ports and any other connectors. Support them when plugging, hold when unplugging * 🙆 If you need to take the cards out, take them out one-by-one from the end, unplug EEM and cables if you feel high tension * 🙆 Use dedicated power supplies for each crate, preferably given or equivalent to given by us * 🙅 Avoid unnecessary inserts and pullouts, especially of MMCX cables Failure to comply with this voids the warranty. ## Shipping hints and warnings * 🙆 Leave the cards in the crate * 🙆 Ensure screws are tight * 🙆 Ensure cards are in card guides * ⚠️ Remove any cables from front panels * ⚠️ Remove SFP adapters and insert caps/stubs * 💁 Also advised to put caps on SMA connectors * ✅ Wrap each crate in the bubble wrap individually until you don't feel the edges of the crate (usually 10 layers of standard buble wrap) * 🈁 Fill in the space around the crate in the box with foamy stuff ## Kasli standalone ### Checklist 1. Build firmware (see commands below) 2. Flash firmware and settings 3. Test hardware with the PSU, which is going to be shipped 4. Create a flash-drive with `device_db.py` file for customers (FAT32) ### CLI commands - build and flash ```shell mkdir cd / nix develop github:m-labs/artiq\?ref=release-7 # master/standalone only artiq_mkfs -s ip 192.168.1.75 kasli.config artiq_flash storage -f kasli.config artiq_ddb_template -o device_db.py .json python -m artiq.gateware.targets.kasli_generic .json artiq_flash --srcbuild -d artiq_kasli// ``` ## Kasli-SoC (zynq) ### Checklist 1. Build firmware (see commands below) for SD card variant 2. Copy `results/boot.bin` to the SD card 3. Insert SD card to the Kasli-SoC and boot 4. Change IP from the default one: `artiq_coremgmt -D 192.168.1.56 config write -s ip 192.168.1.75` 5. Reboot and check it works on new IP address 6. Test hardware with the PSU, which is going to be shipped 7. Create a flash-drive with `device_db.py` file for customers (FAT32) ### CLI commands - build and flash ```shell mkdir cd / nix develop git+https://git.m-labs.hk/m-labs/artiq-zynq\?ref=release-7 artiq_ddb_template -o device_db.py .json nix build -L --impure --expr 'let fl = builtins.getFlake "git+https://git.m-labs.hk/m-labs/artiq-zynq?ref=release-7"; in (fl.makeArtiqZynqPackage {target="kasli_soc"; variant="[master, standalone, satellite]"; json=;}).kasli_soc-[master, standalone, satellite]-sd' # copy `results/boot.bin` to the SD card # insert SD card to the Kasli-SoC and boot artiq_coremgmt -D 192.168.1.56 config write -s ip 192.168.1.75 # or just place extra/CONFIG.TXT near the boot.bin on SD card # update firmware (alternative to copy to SD, if ARTIQ already running) artiq_coremgmt config write -f boot result/boot.bin # reboot via power supply ``` ## Testing (common) ``` artiq_sinara_tester ``` Follow `artiq_sinara_tester` instructions for testing the hardware. For more detailed information, you can use this book's pages, or if there is no instruction for testing your hardware, please add them to this book. ### Known issues * ~~[artiq-zynq#197](https://git.m-labs.hk/M-Labs/artiq-zynq/issues/197) - some cards (Sampler, Mirny, Zotino and others) do not work properly with some EEM ports. You might need to connect the card to the other ports until it gets working.~~ resolved (hopefully) ## Master-satellite setups 1. Change `base` in JSON to the respective `master` or `satellite`, add `"enable_sata_drtio": true` if needed to the master, remove `core_addr` in satellites 2. Build and flash firmware for each crate with JSONs (see instructions above) 3. Create composed `device_db.py`: e.g. `artiq_ddb_template -o device_db.py -s 1 .json -s 2 .json .json` 4. Connect satellite crates to the master respective to their numbers via the fiber (see example picture) ![](img/master_sat_connection.jpg) 5. Ethernet is needed only for master 6. Test hardware as it would be one crate