src/SUMMARY.md

@@ -10,14 +10,13 @@
   - [Sinara 2118 BNC-TTL / 2128 SMA-TTL](./hw/bnc_sma_ttl.md)
   - [Sinara 2138 MCX-TTL](./hw/mcx_ttl.md)
   - [Sinara 5432 DAC Zotino / Sinara 5632 DAC Fastino](./hw/zotino_fastino.md)
-  - [Sinara 5633 HV Amplifier](./hw/hvamp.md)
   - [Sinara 5716 DAC Shuttler](./hw/shuttler.md)
   - [Sinara 5518 BNC-IDC / 5528 SMA-IDC adapter](./hw/bnc_sma_idc_adapter.md)
   - [Sinara 4410/4412 DDS Urukul (AD9910/AD9912)](./hw/urukul.md)
   - [Sinara 5108 Sampler](./hw/sampler.md)
   - [Sinara 6302 Grabber](./hw/grabber.md)
   - [Sinara 7210 Clocker](./hw/clocker.md)
-  - [Sinara 8452 DSP Stabilizer / Sinara 4459 Pounder](./hw/stabilizer_pounder.md)
+  - [Sinara 8452 DSP Stabilizer](./hw/stabilizer.md)
   - [Sinara 9805 RF Power Amplifier Booster](./hw/booster.md)
   - [Sinara 8451 Thermostat](./hw/thermostat.md)
   - [Sinara 2245 LVDS DIO](./hw/lvds_dio.md)

src/hw/hvamp.md

@@ -1,29 +0,0 @@
-# Sinara 5633 HV Amplifier
-
-* [Wiki](https://github.com/sinara-hw/HVAMP_32/wiki)
-
-## Setup
-
-1. Connect the HV Amplifier to the Zotino/Fastino with IDC connectors (stand-alone mode) or with mezzanine connectors (meazzanine mode). Be aware of pin alignment when using it in the meazzanine mode
-2. Connect the DC barrel or ATX cable to HV Amplifier but **don't supply power** 
-
-## Testing
-
-After running `artiq_sinara_test` on the connected Zotino/Fastino:
-
-```text
-*** Testing Zotino DACs and USER LEDs.
-Voltages:
-zotino0 0.1 -0.1 0.2 -0.2 0.3 -0.3 0.4 -0.4 0.5 -0.5 0.6 -0.6 0.7 -0.7 0.8 -0.8 0.9 -0.9 1.0 -1.0 1.1 -1.1 1.2 -1.2 1.3 -1.3 1.4 -1.4 1.5 -1.5 1.6 -1.6
-Press ENTER when done.
-
-*** Testing Fastino DACs and USER LEDs.
-Voltages:
-fastino0 0.1 -0.1 0.2 -0.2 0.3 -0.3 0.4 -0.4 0.5 -0.5 0.6 -0.6 0.7 -0.7 0.8 -0.8 0.9 -0.9 1.0 -1.0 1.1 -1.1 1.2 -1.2 1.3 -1.3 1.4 -1.4 1.5 -1.5 1.6 -1.6
-Press ENTER when done.
-```
-
-1. Turn on the external power supply connecting to the HV Amplifier **(⚠️Danger: High Voltage active, don't touch the bare PCB without PPE)**
-2. Probe with multimeter/DC voltmeter each pair of pins from bottom to top (left pins are ground)
-3. Check that respective pins have voltages multipled by the gains as described by `artiq_sinara_test` (e.g. for 5x gain variant 0.1V pin => 0.1V x 5 = 0.5V )
-4. Check LEDs are on

src/hw/stabilizer.md

@@ -133,46 +133,3 @@ Configure Stabilizer:
 Now, disconnect the USB and connect the Ethernet cable to the Stabilizer, as both won't fit at the same time.
 Stabilizer should connect to moquitto automatically, and you should see the MQTT settings pop up in the MQTT Explorer.
 If the IP address is not set, Stabilizer will try to use DHCP to get an address.
-
-## Installing the Pounder
-
-Remember that the Pounder is not fully supported in official QUARTIQ release; use the firmware from Hydra.
-
-Use ESD precautions; ensure that power is off (both barrel jack and PoE) before installing or removing the card.
-
-There are no guides for the Pounder connector. Line up the connectors with the pins and gently push in.
-
-SMA connectors should line up with the ones from Stabilizer; no pins should be visible from the sides of the Pounder; it's more obvious if the Pounder has the front panel already installed.
-
-## Testing the Pounder
-
-### With serial only
-
-You need to have the Stabilizer powered on and connected through USB. Ethernet is not necessary.
-
-Input the following sequence of commands into the shell, assuming Stabilizer serial interface is visible at /dev/ttyACM0:
-```
-stty 115200 -F /dev/ttyACM0
-echo 'set /dual_iir/pounder/out_channel/0/dds/frequency 20e6' > /dev/ttyACM0
-echo 'set /dual_iir/pounder/out_channel/0/dds/amplitude 1' > /dev/ttyACM0
-echo 'set /dual_iir/pounder/out_channel/0/attenuation 16' > /dev/ttyACM0
-echo 'set /dual_iir/pounder/out_channel/1/dds/frequency 30e6' > /dev/ttyACM0
-echo 'set /dual_iir/pounder/out_channel/1/dds/amplitude 1' > /dev/ttyACM0
-echo 'set /dual_iir/pounder/out_channel/1/attenuation 16' > /dev/ttyACM0
-```
-
-You can copy them all and input at once.
-
-Observe a sine wave with frequency of 20MHz on channel 0 output, and 30MHz on channel 1 output.
-
-### With MQTT (slower)
-
-For this method, you need to set up MQTT and have the Stabilizer connected with Ethernet.
-
-1. Set up the MQTT as described above.
-2. Using Mosquitto and MQTT Explorer, set the pounder ``out_channel`` parameters:
-* Frequency: 20e6 (20MHz)
-* Amplitude: 1.0
-   ![Pounder MQTT settings](../img/pounder_mqtt.png)
-3. Repeat the procedure for the other channel.
-4. Observe a sine wave of given frequency with an oscilloscope in the output channel.