diff --git a/src/hw/stabilizer.md b/src/hw/stabilizer.md
index 8f149d5..887c966 100644
--- a/src/hw/stabilizer.md
+++ b/src/hw/stabilizer.md
@@ -10,9 +10,19 @@ EEM is used for power only, and it can be alternatively powered by 12V barrel ja
 
 Not present in the JSON.
 
-## Building
+## Getting the firmware
 
-Pick your poison - firmware version: older with Pounder support or newer with USB serial console - the first works with a hardcoded MQTT broker and (static or dynamic) IP address, the latter is configured like the booster - through a serial console.
+You can get the firmware from [Hydra](https://nixbld.m-labs.hk/jobset/mcu/mcu-contrib).
+
+* ``stabilizer-dual-iir`` supports Pounder v1.2 - probably you should flash this one,
+* ``stabilizer-dual-iir-pounder_v1_0`` supports Pounder 1.0 and 1.1 (legacy),
+* ``stabilizer-lockin`` is a different application which we do not usually flash.
+
+These all include changes to the mainline code to include Pounder telemetry.
+
+### Building (optional)
+
+Please keep in mind that the firmware from the official Quartiq repository does not include support for Pounder in MQTT, you may need to use a fork for that. But if the stabilizer is without a Pounder, it's also a valid option.
 
 There is no Nix Flake support to make things easier, so you need to set up rust and cargo manually. Start with cloning the stabilizer repository and opening a new shell with dfu-util (for flashing) and rustup (for building).
 
@@ -30,27 +40,18 @@ rustup update
 rustup default stable
 ```
 
-Building the older version:
-
-```
-BROKER="MQTT BROKER IP" cargo build --release
-BROKER="MQTT BROKER IP" cargo objcopy --release --bin dual-iir -- -O binary dual-iir.bin
-```
-
-Building the newer version:
+Building:
 
 ```
 cargo build --release
 cargo objcopy --release --bin dual-iir -- -O binary dual-iir.bin
 ```
 
-The newer version must be configured with USB console later (try ``help`` command first).
-
 ## Flashing
 
-Once you have the binary (either built, or received from someone), you can now flash it.
+Once you have the binary, you can now flash it.
 
-Without firmware on the device or with older firmware, you need to use the jumper method:
+Without firmware on the device or with older firmware (without USB serial console), you need to use the jumper method:
 
 1. Have the Stabilizer disconnected from power.
 2. Use a jumper of some sort to short BOOT pins on the board.
@@ -75,9 +76,11 @@ dfu-util -a 0 -s 0x08000000:leave -R -D dual-iir.bin
 
 7. Look for "File downloaded successfully".
 
+For normal usage, the stabilizer must be configured with USB console later (try ``help`` command first), to set its IP address and MQTT broker address. However, for general testing (like the one below), you don't need to configure it any further.
+
 ## Testing
 
-1. Ensure that the [firmware](https://github.com/quartiq/stabilizer) has been flashed onto the Stabilizer
+1. Ensure that the [firmware](#getting-the-firmware) has been flashed onto the Stabilizer
 2. Turn on the crate/Stabilizer via EEM cable or power supply
 3. Set up the signal generator for an amplitude of 1V, frequency of 10kHz, and a sine wave
 4. Use the splitter to connect the generator's output to ADC0 and to the oscilloscope (refer to the picture below)