53 lines
2.1 KiB
Markdown
53 lines
2.1 KiB
Markdown
|
# Sinara 7210 Clocker
|
||
|
|
|
||
|
|
[Wiki](https://github.com/sinara-hw/Clocker/wiki)
|
||
|
|
|
||
|
|
## JSON
|
||
|
|
|
||
|
|
Put the `ext_ref_frequency` field into the JSON description if the Clocker is going to use an external frequency:
|
||
|
|
|
||
|
|
```json
|
||
|
|
{
|
||
|
|
"hw_rev": "<hw rev>",
|
||
|
|
"base": "<base>",
|
||
|
|
...
|
||
|
|
"ext_ref_frequency": <freq in Hz>,
|
||
|
|
...
|
||
|
|
"peripherals": [...]
|
||
|
|
}
|
||
|
|
```
|
||
|
|
|
||
|
|
On peripherals you should choose `"clk_sel": 2` on connected devices.
|
||
|
|
|
||
|
|
## Setup
|
||
|
|
|
||
|
|
For tests, you may need an external RF generator, depending on customer needs.
|
||
|
|
Here is example setup for SynthNV RF signal generator:
|
||
|
|
|
||
|
|
1. Connect SynthNV to the workstation via USB, and
|
||
|
|
2. Install and run `cutecom`: `nix-shell -p cutecom`
|
||
|
|
3. Set settings as on the picture below:
|
||
|
|
|
||
|
|
4. Open the device, usually it is `/dev/ttyACM0`
|
||
|
|
5. Put `?` into `Input` field and press `Enter` for current settings and help commands
|
||
|
|
6. For changing the frequency, enter `f<freq in MHz>`, e.g. `f125.0` for 125 MHz
|
||
|
|
7. Set RF power so that clocker would recognize the signal with `a<power>` command, e.g. `a63`
|
||
|
|
8. Check for desired amplitude and frequency at the `RFOut` (see picture below for reference) pin via oscilloscope
|
||
|
|
|
||
|
|
9. If everything is ok, connect `RFOut` to the `CLK IN` on the Clocker (see instructions below for details)
|
||
|
|
|
||
|
|
### Setup the Clocker
|
||
|
|
|
||
|
|
1. Connect MMCx cables according to the customer needs and boards specifications (see image below for reference)
|
||
|
|
2. Connect the Clocker to the Kasli via 30-pin ports
|
||
|
|
|
||
|
|
3. Connect the Clocker's SMA output to the Kasli's `CLK`/`CLK IN` SMA pin
|
||
|
|
4. After assembling the crates and flashing the firmware, start Kasli and write config as follows:
|
||
|
|
`artiq_coremgmt config write -s rtio_clock ext0_bypass`. Please refer to the [official manual](https://m-labs.hk/artiq/manual/installing.html#miscellaneous-configuration-of-the-core-device)
|
||
|
|
for the details and available options
|
||
|
|
5. Reboot either via `artiq_coremgmt reboot` or via power supply if the board's firmware doesn't have such command
|
||
|
|
|
||
|
|
## Testing
|
||
|
|
|
||
|
|
Run `artiq_sinara_test` and check that it doesn't fail on the connected devices.
|