* coredevice.ad9910: Add return type hints to conversion functions
* coredevice.ad9910: Make set_pow write correct number of bits
The AD9910 expects 16 bits. Thus, if writing 32 bits to the POW register, the chip would likely enter a locked-up state.
* coredevice.ad9910: Correct data alignment in write_16
Co-authored-by: Robert Jördens <rj@quartiq.de>
* coredevice.ad9910: Add function to read from 16 bit registers
Co-authored-by: drmota <peter.drmota@physics.ox.ac.uk>
Co-authored-by: Robert Jördens <rj@quartiq.de>
* ad9910: fix asf range
The ASF is a 14-bit word. The highest possible value is 0x3fff, not
0x3ffe. `int(round(1.0 * 0x3fff)) == 0x3fff`.
I don't remember and understand why this was 0x3ffe since the beginning.
0x3fff was already used as a default in `set_mu()`
Signed-off-by: Robert Jördens <rj@quartiq.de>
* RELEASE_NOTES: ad9910 asf scale change
Co-authored-by: David Nadlinger <code@klickverbot.at>
* Input validation and masking of SI -> mu conversions (close#1446)
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* Update RELEASE_NOTES
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
Co-authored-by: Robert Jördens <rj@quartiq.de>
* ad53xx: voltage_to_mu() validation & documentation (closes#1443, #1444)
The voltage input (float) is checked for validity. If we need more
speed, we may want to check the DAC-code for over/underflow instead.
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* ad53xx documentation: voltage_to_mu is only valid for 16-bit DACs
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* AD53xx: add voltage_to_mu method (closes#1341)
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* ad53xx: improve voltage_to_mu performance
Interger comparison is faster than floating point math.
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* AD53xx: voltage_to_mu method now uses attribute values
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* Fixup RELEASE_NOTES.rst
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* ad53xx: documentation improvements
voltage_to_mu return value
14-bit DAC support
Signed-off-by: Marius Weber <marius.weber@physics.ox.ac.uk>
* This targets unrelease CPLD gateware (https://github.com/quartiq/mirny/issues/1)
* includes initial coredevice driver, eem shims, and kasli_generic tooling
* addresses the ARTIQ side of #1130
* Register abstraction to be written
Signed-off-by: Robert Jördens <rj@quartiq.de>
This removes:
* host-side keepalive, which turns out not to be required
* custom connection timeout (the default is OK)
* SSH tunneling support (doesn't seem to be actually used anywhere)
* updated adoo10.py for RAM mode frequency control
* updated docstrings for set_cfr1() in ad9910.py
* fixed typo in ad9910.py
* added docstrings to ad9910.py
* removed OSK-related changes in AD9910, to be included in a separate branch.
* updated AD9910 set_cfr1 for control of OSK mode parameters
* updated AD9910 set_cfr1() for control of OSK mode parameters.
This hopefully suggests a bit better that the value is the last one
fetched by the servo (i.e. needs the servo active to update), rather
than somehow requesting a new sample to be taken.
As already mentioned in the gateware.
One alternative would be to detect address collisions and
stall the read for one cycle.
Note that there will in general not be a consistent view of the servo
state unless the servo is stopped.
close#1337
