f87da95e57
jesd204: use jesd clock domain for sysref sampler
...
RTIO domain is still in reset during calibration.
2018-06-22 17:13:01 +08:00
76fc63bbf7
jesd204: use separate controls for reset and input buffer disable
2018-06-22 11:38:18 +08:00
d9955fee76
jesd204: make sure IOB FF is used to sample SYSREF at FPGA
2018-06-22 11:00:56 +08:00
60b22217ce
sayma: set DRTIO master HMC830_REF to 100MHz
2018-06-22 10:10:09 +08:00
e6d1726754
sayma: add RTIO log to DRTIO master
2018-06-22 00:05:22 +08:00
83428961ad
sayma: add SAWG and JESD to DRTIO master
2018-06-22 00:04:22 +08:00
c1db02a351
drtio/gth_ultrascale: disable IBUFDS_GTE3 until stable_clkin
...
Precaution against HMC7043 noise issues.
2018-06-21 22:56:07 +08:00
8b3c12e6eb
sayma: clock DRTIO master transceiver from HMC7043
2018-06-21 22:34:44 +08:00
de7d64d482
sayma: clock JESD204 from GTP CLK2
...
This frees up GTP CLK1, which is routable to the SFP quads, for DRTIO.
2018-06-21 22:33:53 +08:00
b28ff587c5
sayma: add sysref sampler to DRTIO master
2018-06-21 22:28:34 +08:00
e29536351d
drtio: resync SYSREF when TSC is loaded
2018-06-21 17:00:32 +08:00
45e8263208
hmc7043: do not configure phases during initial init
...
They are determined later on.
2018-06-21 15:54:42 +08:00
28fb0fd754
sayma: add SYSREF sampler gateware
2018-06-20 17:48:35 +08:00
9142a5ab8a
rtio: expose coarse timestamp in RTIO and DRTIO satellite cores
2018-06-20 17:39:54 +08:00
75b6cea52f
sayma: add SAWG to DRTIO satellite
2018-06-19 19:12:10 +08:00
433273dd95
sayma: support RTM FPGA, HMC830 and HMC7043 in DRTIO master and satellite
2018-06-19 14:33:48 +08:00
6403a0d5d1
sayma_amc: update without-sawg description
2018-06-19 13:52:05 +08:00
d29b3dd588
hmc830: compile-time configurable reference frequency
2018-06-19 13:47:32 +08:00
6f3ed81626
targets/sayma_rtm: fix description
2018-06-18 17:46:53 +08:00
32484a62de
sayma_amc: remove unused imports
2018-06-17 13:09:44 +02:00
53ab255c00
sayma_amc: enable slave fpga loading ( #813 )
2018-06-16 12:47:26 +02:00
1029ac870b
sayma_rtm: don't drive txen pins
...
pins disabled by config
necessary for using that pin as DIN (#813 )
2018-06-13 16:11:30 +00:00
68d16fc292
serwb: support single-ended signals
...
Low-speed PHY only.
2018-06-13 21:28:21 +08:00
a9a25f2605
sayma_rtm: drive ref_lo_clk_sel, and set clk muxes early
2018-06-12 20:00:12 +02:00
a143e238a8
savel_fpga: get rid of unneeded config
2018-06-12 10:24:04 +02:00
0b086225a9
sawg: don't use Cat() for signed signals
...
c.f. #1039 #1040 #1022 #1058 #1044
2018-06-09 07:33:47 +00:00
5b73dd8604
sawg: accurate unittest rtio freq
2018-06-08 17:22:13 +02:00
e5f6750171
sawg: cleanup double assign
2018-06-08 14:31:55 +00:00
Florent Kermarrec
53e9e475d0
serwb: transmit zeroes when nothing to transmit (for prbs), improve rx idle detection
2018-06-08 16:10:31 +02:00
Florent Kermarrec
7296a76f18
serwb: move common datapath code to datapath.py, simplify flow control
2018-06-08 12:37:08 +02:00
Florent Kermarrec
89797d08ed
serwb: revert to 125MHz linerate (until we understand why 1gbps version breaks between builds)
2018-06-07 15:13:56 +02:00
b4c2b148d1
sawg: don't use Mux for signed signals
...
migen#75
2018-06-06 15:51:14 +00:00
Florent Kermarrec
009db5eda9
serwb: revert 1gbps linerate
2018-06-06 16:20:20 +02:00
cae92f9b44
kasli: add Tsinghua variant
2018-06-06 19:03:45 +08:00
e21b7965b9
sayma_amc: change test patterns for 'without-sawg'
2018-06-06 08:02:52 +00:00
af88c4c93e
clean up hmc7043 reset
2018-06-05 20:41:48 +08:00
Thomas Harty
ac5c4913ec
Sayma RTM: hold hmc7043 in reset/mute state during init.
2018-06-05 19:22:04 +08:00
07d4145a35
correct documented siphaser VCO frequency [NFC]
2018-06-04 20:53:43 +08:00
bb87976d4f
suservo: docstring fixes, revert parametrization of r_rtt
2018-06-04 07:27:17 +00:00
07a1425e51
SUservo EEM docs
...
add documentation to eem.SUServo. Change parameterization of t_rtt to include delays on Sampler, as this seems simpler and more robust to changing RTIO frequencies in the future.
c.f. #1046
2018-06-04 08:51:28 +02:00
f50aef1a22
suservo: extract boilerplate
...
closes #1041
2018-06-01 15:37:07 +00:00
9b5a46dffd
suservo: fix restart counter assertion
...
c.f. #788
2018-05-31 15:56:11 +00:00
Paweł
44c7a028cb
Added second argument to DIO.add_STD in master and satellite variant of kasli (now builds properly)
2018-05-30 22:49:40 +08:00
ad099edf63
kasli: integrate grabber
2018-05-28 22:43:40 +08:00
563e434e15
eem: finalize grabber support
2018-05-28 22:43:06 +08:00
2612fd1e72
rtio: add grabber deserializer and WIP PHY encapsulation
2018-05-28 22:42:27 +08:00
Florent Kermarrec
e21f14c0b3
serwb/phy: typo (KUSSerdes --> KUSerdes)
2018-05-28 10:41:11 +02:00
b20a8c86b0
kasli: don't bother with grabber ttls for now
...
not used on target cameras
2018-05-28 07:31:00 +02:00
80c69da17e
eem: add Grabber IOs and CC
2018-05-28 11:16:23 +08:00
bb248970df
style
2018-05-28 10:40:05 +08:00
b09d07905c
kasli: add LUH/PTB/HUB variants
...
and refactor/simplify variant selection
2018-05-27 18:33:27 +00:00
Florent Kermarrec
bca2969957
sayma_rtm: add RTMScratch module to test remote Wishbone accesses
2018-05-24 16:53:10 +02:00
19efd8b13e
kasli: refactor EEM code
2018-05-24 18:41:54 +08:00
4e5fe672e7
kasli: add tester target
2018-05-21 17:43:39 +08:00
72aef5799e
kasli/ustc: use TTLOut
2018-05-18 22:55:28 +08:00
b10d3ee4b4
make RTIO clock switch optional and simplify
...
Kasli no longer has an internal RTIO clock.
Switching clocks dynamically is no longer supported.
2018-05-18 17:41:34 +08:00
8a988d0feb
kasli: remove leftover debug print
2018-05-18 17:25:23 +08:00
37bd0c2566
kasli: add USTC target
2018-05-18 16:15:07 +08:00
Florent Kermarrec
f77bcbebb5
serwb/test_serwb_core: fix
2018-05-16 08:34:53 +02:00
Florent Kermarrec
77fc5c599f
serwb/test: update
2018-05-15 23:52:58 +02:00
Florent Kermarrec
3873d09692
serwb: rewrite high-speed phys by splitting clocking/tx/rx, scrambling is now always enabled.
2018-05-15 23:52:41 +02:00
Florent Kermarrec
f8a9dd930b
serwb/genphy: add device parameter (not used here, but this way all the phys share the same parameters), scrambling is also now always enabled.
2018-05-15 23:51:14 +02:00
Florent Kermarrec
2c627cd061
serwb/scrambler: simplify and set scrambler input data to 0 when sink.stb == 0
2018-05-15 23:49:17 +02:00
Florent Kermarrec
c18a73d45f
sayma_amc/rtm: use new serwb low-speed phy
2018-05-15 16:40:50 +02:00
Florent Kermarrec
913d1e8e12
serwb: add generic low-speed phy (125Mhz linerate, same phy for ultrascale/7-series)
2018-05-15 16:39:39 +02:00
Florent Kermarrec
520aade8fe
serwb/scrambler: cleanup/fix potential bug
2018-05-15 16:30:52 +02:00
504d37b66b
suservo: add SI units functions and document
...
m-labs/artiq#788
2018-05-14 12:26:49 +00:00
d71e4e60a9
suservo: use addition for offset
2018-05-14 12:26:49 +00:00
27f975e7bb
kasli: eem DifferentialInputs need DIFF_TERM
...
cleanup some formatting on the way
2018-05-14 12:26:49 +00:00
2a47b934ea
suservo: remove adc return clock gating
2018-05-14 12:26:49 +00:00
74c0b4452b
suservo: clkout and sdo[b-d] are inverted
2018-05-14 12:26:49 +00:00
04240cdc08
suservo: sampler channels are reversed
2018-05-14 12:25:09 +00:00
3027951dd8
integrate new AD9914 driver
...
moninj, analyzer, docs, examples, tests.
2018-05-13 23:29:35 +08:00
whitequark
ee4c475cf3
gateware: fix Sayma satellite build.
...
RTIO clock multiplier was removed from Sayma in 32f22f4c
2018-05-13 13:10:39 +00:00
8c1390e557
kasli: use 62.5MHz clock for siphaser reference ( #999 )
2018-05-12 22:58:03 +08:00
2426fea3f2
siphaser: support external reference for the freerunning 150MHz
2018-05-12 22:57:11 +08:00
6796413a53
serwb: remove unnecessary shebang line
2018-05-12 22:49:44 +08:00
Florent Kermarrec
f5208ff2f3
serwb/core: reduce buffering, use buffered=True
2018-05-12 12:03:58 +02:00
Florent Kermarrec
fdc953e569
serwb/etherbone: recuce buffering
2018-05-12 12:03:11 +02:00
Florent Kermarrec
6e67e6d0b1
serwb: revert some changes (was breaking simulation)
2018-05-12 11:59:46 +02:00
Florent Kermarrec
0a6d4ccd85
serwb/phy: improve/cleanup init
2018-05-12 01:35:34 +02:00
Florent Kermarrec
b6ab59fb80
serwb/phy: increase timeout
2018-05-12 01:32:55 +02:00
Florent Kermarrec
e09dbc89bc
serwb: remove idelaye3 en_vtc (was not done correctly, we'll add direct software control)
2018-05-12 01:32:16 +02:00
Florent Kermarrec
cd4477864a
serwb: fix case when rtm fpga is not loaded, lvds input can be 0 or 1
2018-05-11 23:31:25 +02:00
2e3bf8602f
serwb: reduce buffering. Closes #997
2018-05-11 14:13:41 +08:00
6b811c1a8b
sayma: fix runtime/rtm gateware address conflict
2018-05-09 19:47:29 +08:00
f055bf88f6
suservo: add clip flags ( #992 )
2018-05-09 07:16:15 +00:00
Florent Kermarrec
60fd362d57
serwb: fix rx_comma detection
2018-05-07 23:54:35 +02:00
7d4a103a43
opticlock, suservo: set default kasli hw_rev
2018-05-07 09:07:18 +02:00
whitequark
b1d349cc1b
firmware: implement a sampling profiler.
...
Does not yet support constructing call graphs.
2018-05-05 00:44:40 +00:00
5f0cfadb30
rtio/sed: add unittest for sequence number rollover
2018-05-02 12:04:30 +08:00
4120105e3a
rtio/sed: fix output network cmp_wrap
2018-05-02 12:04:03 +08:00
bce8fa3ec5
rtio/sed: add replace unittest at the top level ( #978 )
2018-05-02 10:58:18 +08:00
83fb431cd0
rtio/sed: pass sequence numbers through the FIFOs. Closes #978
2018-05-02 10:57:57 +08:00
Florent Kermarrec
05955bfd79
sayma_rtm: use bufio for sys4x (needed since we are using a -1 speedgrade)
2018-05-01 22:16:35 +02:00
Florent Kermarrec
84e1f05559
sayma_rtm: make cd_sys4x clock domain reset_less
2018-05-01 16:11:26 +02:00
Florent Kermarrec
64c8eee28d
serwb/phy/master: fix slave ready detection by filtering possible glitches on rx data (seems to happen when RTM fpga is not loaded)
2018-04-30 23:59:56 +02:00
5a683ddd1f
Revert "kasli: force hw_rev for the different targets"
...
This reverts commit 17d7d7856a
2018-04-28 23:24:41 +02:00
17d7d7856a
kasli: force hw_rev for the different targets
2018-04-28 21:30:29 +02:00
5d3c76fd50
sayma_rtm: use bitstream opts in migen
2018-04-27 15:43:32 +00:00
5f00326c65
suservo: coeff mem write port READ_FIRST
2018-04-27 15:43:32 +00:00
307cd07b9d
suservo: lots of gateware/ runtime changes
...
tested/validated:
* servo enable/disable
* dds interface, timing, io_update, mask_nu
* channel control (en_out, en_iir, profile)
* profile configuration (coefficients, delays, offsets, channel)
* adc timings and waveforms measured
* asf state readback
* adc readback
individual changes below:
suservo: correct rtio readback
suservo: example, device_db [wip]
suservo: change rtio channel layout
suservo: mem ports in rio domain
suservo: sck clocked from rio_phy
suservo: cleanup, straighten out timing
suservo: dds cs polarity
suservo: simplify pipeline
suservo: drop unused eem names
suservo: decouple adc SR from IIR
suservo: expand coredevice layer
suservo: start the correct stage
suservo: actually load ctrl
suservo: refactor/tweak adc timing
suservo: implement cpld and dds init
2018-04-27 13:50:26 +02:00
Florent Kermarrec
8212e46f5e
sayma_amc: filter jesd refclk/sysref with jreset (hmc7043 can generate noise when unconfigured see sinara issue #541 )
2018-04-27 13:04:37 +02:00
f9b2c32739
suservo: add pgia spi channel
2018-04-25 17:14:25 +00:00
c83305065a
suservo: add servo/config/status register
2018-04-25 15:59:06 +00:00
105068ad90
suservo: fix restart timing
2018-04-25 15:19:49 +00:00
c304b6207a
suservo: drop adc idelays
2018-04-25 14:59:50 +00:00
b44d6517d1
suservo: use 125 MHz SDR ADC
...
* easier timing
* natural sampling on rising edge
* timing, signal robustness
* adjust the servo iteration timing
2018-04-25 14:32:23 +00:00
37c186a0fc
suservo: refactor, constrain
...
* remove DiffMixin, move pad layout handling to pads
* add input delay constraints, IDELAYs
2018-04-25 13:44:52 +00:00
d0258b9b2d
suservo: set input delays
2018-04-24 15:30:25 +00:00
fe75064c1e
suservo: cleanup rtio interface
2018-04-24 13:08:40 +00:00
3942c2d274
suservo: fix clkout cd drive
2018-04-24 10:18:32 +00:00
f74998a5e0
suservo: move arch logic to top, fix tests
2018-04-23 21:11:26 +00:00
4903eb074c
suservo: use BUFIO/BUFH for ADC
2018-04-23 18:30:19 +00:00
e36deab0a8
suservo/adc: try to help vivado extract srls
2018-04-23 18:30:19 +00:00
929ed4471b
kasli/SUServo: use suservo, implement urukul_qspi
...
m-labs/artiq#788
2018-04-23 18:30:18 +00:00
4c1e356f67
suservo: add pads rewiring layer for eems
2018-04-23 18:30:18 +00:00
99dd9c7a2a
suservo: fix rtio interface width
2018-04-23 18:30:18 +00:00
d5eea962ec
suservo: fix cnv_b diff
2018-04-23 18:30:12 +00:00
c8fd63754a
suservo: add unittests
...
m-labs/artiq#788
2018-04-23 18:25:59 +00:00
934c41b90a
gateware: add suservo
...
from
fe4b60b902m-labs/artiq#788
2018-04-23 18:24:59 +00:00
Florent Kermarrec
439d2bf2bc
sayma/serwb: adapt, full reset of rtm on link reset
2018-04-17 19:24:03 +02:00
Florent Kermarrec
8edf4541d6
serwb: adapt test
2018-04-17 19:21:53 +02:00
Florent Kermarrec
20ccc9d82f
serwb/core/phy: move scrambler in phy, add link test, revert delay min/max checks
2018-04-17 19:21:21 +02:00
Florent Kermarrec
ebfac36223
serwb/scrambler: dynamic enable/disable
2018-04-17 19:20:06 +02:00
Florent Kermarrec
816a6f2ec7
serwb/phys: remove phy_width (revert linerate to 1Gbps)
2018-04-17 19:19:18 +02:00
eac447278f
kasli: add MITLL variant
2018-04-17 19:00:11 +08:00
756e120c27
kasli/sysu: add comments
2018-04-17 18:46:55 +08:00
Florent Kermarrec
1acd7ea1db
sayma/serwb: re-enable scrambling
2018-04-17 00:49:36 +02:00
Florent Kermarrec
ca01c8f1cb
sayma: reduce serwb linerate to 500Mbps
2018-04-16 23:19:15 +02:00
Florent Kermarrec
825a2158ba
serwb: add phy_width parameter to allow reducing linerate to 500Mbps or 250Mbps
2018-04-16 23:19:14 +02:00
Florent Kermarrec
bb90fb7d59
sayma/serwb: remove scrambling (does not seems to work on sayma for now...)
2018-04-07 15:57:57 +02:00
Florent Kermarrec
6aa8e2c433
serwb/test: replace valid/ready with stb/ack
2018-04-07 15:55:57 +02:00
Florent Kermarrec
73dbc0b6b6
serwb/test: adapt to new version
2018-04-07 15:09:29 +02:00
Florent Kermarrec
e15f8aa903
sayma/serwb: enable scrambling
2018-04-07 14:52:37 +02:00
Florent Kermarrec
9d0e8c27ff
serwb/scrambler: add flow control
2018-04-07 14:51:17 +02:00
Florent Kermarrec
2f8bd022f7
sayma_rtm: remove sys0p2x clock
2018-04-07 03:10:34 +02:00
Florent Kermarrec
1fd96eb0fd
serwb: replace valid/ready with stb/ack
2018-04-07 03:06:19 +02:00
Florent Kermarrec
c8a08375f8
serwb: replace valid/ready with stb/ack
2018-04-07 03:03:44 +02:00
Florent Kermarrec
73b727cade
serwb: new version using only sys/sys4x clocks domains, scrambling deactivated.
2018-04-07 02:59:14 +02:00
Florent Kermarrec
dd21c07b85
targets/sayma_rtm: fix serwb 2 ...
2018-04-03 18:59:05 +02:00
Florent Kermarrec
7488703f23
targets/sayma_rtm: fix serwb
2018-04-03 18:57:00 +02:00
Florent Kermarrec
aef0153a8f
targets/sayma: adapt to new serwb clocking
2018-04-03 18:53:39 +02:00
Florent Kermarrec
3248caa184
gateware/serwb: move all clocking outside of serwb, use existing sys/sys4x clocks
2018-04-03 18:48:08 +02:00
f0771765c1
rtio: move CRI write comment to more appropriate location
2018-03-29 23:55:00 +08:00
493d2a653f
siphaser: add false path between sys_clk and mmcm_freerun_output
2018-03-29 10:55:41 +08:00
4229c045f4
kasli: fix DRTIO master clock constraint
2018-03-29 10:20:31 +08:00
3d89ba2e11
sayma: remove debug leftover
2018-03-29 10:20:17 +08:00
605292535c
kasli: ignore OSERDESE2->ISERDESE2 timing path on DRTIO targets as well
2018-03-29 10:12:02 +08:00
whitequark
bab6723ff2
Revert "gateware: don't run tests if there is no migen."
...
This reverts commit 4804cfef9b
2018-03-26 03:33:52 +00:00
whitequark
4804cfef9b
gateware: don't run tests if there is no migen.
...
This allows us to skip testing gateware on Windows.
2018-03-26 03:26:34 +00:00
3a0dfb7fdc
ad53xx: port monitor, moninj dashboard, kc705 target
2018-03-24 16:04:02 +01:00
1553fc8c7d
sed: reset valid in output sorter
2018-03-23 11:11:11 +00:00
770b0a7b79
novogorny: conv -> cnv
...
* parity with sampler
* also add novogorny device to opticlock
2018-03-21 18:38:42 +00:00
1afce8c613
kasli: simplify single eem pin formatting
2018-03-21 13:08:42 +01:00
d48b8f3086
kasli: fix sampler sdr/cnv pins
2018-03-21 09:28:00 +00:00
1fb5907362
kasli: add SUServo variant (Sampler-Urukul Servo)
2018-03-21 08:53:26 +00:00
f74d5772f4
sampler: add wide eem definition
2018-03-21 08:53:26 +00:00
32f22f4c9c
sayma: disable SERDES TTL entirely
...
Timing closure becomes very random, even at 4X.
2018-03-21 13:03:48 +08:00
f8c2d54e75
ttl_serdes_ultrascale: configurable SERDES ratio. Also try X4 on Sayma
2018-03-21 13:01:38 +08:00
9c2d343052
sayma: use SERDES RTIO TTL
...
This is not enabled on the standalone design as it breaks timing.
2018-03-21 10:53:52 +08:00
c8020f6bbd
ttl_serdes_generic: fix/upgrade test
2018-03-20 16:46:57 +08:00
a5825184b7
add ttl_serdes_ultrascale (untested)
2018-03-20 16:07:23 +08:00
fad066f1aa
ttl_serdes_7series: cleanup indentation
...
Inconsistent with other code and confuses text editors.
2018-03-20 15:50:04 +08:00
Thomas Harty
37d431039d
Fix typos.
...
Reduce ififo depth to 4 for Zotino.
2018-03-19 09:42:18 +00:00
Thomas Harty
c4fa44bc62
Add Zotino and Sampler functions to Kasli. Add Zotino to Kasli EEM 7 on OptiClock.
2018-03-18 00:25:43 +00:00
a315ecd10b
rtio/ttl_serdes_7series: reset IOSERDES ( #958 )
2018-03-14 09:01:29 +08:00
2fdc180601
dsp/fir: outputs reset_less (pipelined)
2018-03-13 17:11:50 +00:00
2edf65f57b
drtio: fix satellite minimum_coarse_timestamp clock domain ( #947 )
2018-03-13 00:20:57 +08:00
1d081ed6c2
drtio: print diagnostic info on satellite write underflow ( #947 )
2018-03-12 23:41:19 +08:00
Florent Kermarrec
eb6e59b44c
sayma_rtm: fix serwb timing constraints (was causing the gated clock warning)
2018-03-12 11:25:29 +01:00
6dfebd54dd
ttl_serdes_7series: use correct IBUFDS_INTERMDISABLE port names
2018-03-12 10:37:33 +08:00
fc3d97f1f7
drtio: remove spurious multichannel transceiver clock constraints
...
They used to cause (otherwise harmless) Vivado critical warnings.
2018-03-09 22:46:27 +08:00
caf7b14b55
kasli: generate fine RTIO clock in DRTIO targets, separate RTIO channel code
2018-03-09 22:36:16 +08:00
3fbcf5f303
drtio: remove TSC correction ( #40 )
2018-03-09 10:36:17 +08:00
e38187c760
drtio: increase default underflow margin. Closes #947
2018-03-09 00:49:24 +08:00
8bd15d36c4
drtio: fix error CSR edge detection ( #947 )
2018-03-08 16:28:25 +08:00
82831a85b6
kasli/opticlock: add eem6 phys
2018-03-07 21:32:59 +01:00
3a6566f949
rtio: judicious spray with reset_less=True
...
Hoping to reduce rst routing difficulty and easier RTIO timing closure.
2018-03-07 14:57:18 +00:00
b0282fa855
spi2: reset configuration in rio_phy
2018-03-07 14:42:11 +00:00
4af7600b2d
Revert "LaneDistributor: try equivalent spread logic"
...
This reverts commit 8b70db5f17
2018-03-07 11:34:51 +00:00
a6d1b030c1
RTIO: use TS counter in the correct CD
...
artiq/m-labs#938
2018-03-07 11:34:42 +00:00
8b70db5f17
LaneDistributor: try equivalent spread logic
2018-03-07 11:34:42 +00:00
2cbd597416
LaneDistributor: style and signal consolidation [NFC]
2018-03-07 11:34:42 +00:00
916197c4d7
siphaser: cleanup
2018-03-07 11:15:44 +08:00
f7aba6b570
siphaser: fix phase_shift_done CSR
2018-03-07 10:57:30 +08:00
acfd9db185
siphaser: minor cleanup
2018-03-07 10:57:30 +08:00
7d98864b31
sayma: enable siphaser
2018-03-07 10:57:30 +08:00
a6e29462a8
sayma: enable multilink DRTIO
2018-03-07 10:57:30 +08:00
c34d00cbc9
drtio: implement Si5324 phaser gateware and partial firmware support
2018-03-07 10:57:30 +08:00
994ceca9ff
sayma_amc: disable slave fpga gateware loading
2018-03-06 17:27:43 +01:00
62af7fe2ac
Revert "kasli/opticlock: use plain ttls for channels 8-23"
...
This reverts commit bd5c222569eb68d624a5ac1e9f2542f6ee553f83.
No decrease in power consumption or improvement in timing.
2018-03-06 14:27:19 +01:00
fd3cdce59a
kasli/opticlock: use plain ttls for channels 8-23
2018-03-06 14:27:19 +01:00
50298a6104
ttl_serdes_7series: suppress diff_term in outputs
2018-03-06 14:27:19 +01:00
e356150ac4
ttl_simple: support differential io
2018-03-06 14:27:19 +01:00
956098c213
kasli: add second urukul, make clk_sel drive optional
2018-03-06 14:26:27 +01:00
07de7af86a
kasli: make second eem optional in urukul
2018-03-06 14:26:26 +01:00
c25560baec
sed: more LaneDistributor comments
2018-03-06 20:56:35 +08:00
f40255c968
sed: add comments about key points in LaneDistributor
2018-03-06 20:51:09 +08:00
Florent Kermarrec
5b3d6d57e2
drtio/gth: power down rx on restart (seems to make link initialization reliable)
2018-03-06 11:49:28 +01:00
