diff --git a/README_PHASER.rst b/README_PHASER.rst
index 369d91877..da245579d 100644
--- a/README_PHASER.rst
+++ b/README_PHASER.rst
@@ -13,7 +13,7 @@ Ultimately it will be the basis for the ARTIQ Sayma Smart Arbitrary Waveform Gen
 * Full configurability of the AD9154 and AD9516 through SPI with ARTIQ kernel support
 * All SPI registers and register bits exposed as human readable names
 * Parametrized JESD204B core (also capable of operation with eight lanes)
-* The code can be reconfigured. Possible example configurations are: support 2 channels at 1 GHz datarate, support 4 channels at 300 MHz data rate, no interpolation, and using mix mode to stress the second and third Nyquist zones (150-300 MHz and 300-450 MHz).
+* The code can be reconfigured. Possible example configurations are: support 2 channels at 1 GHz datarate, support 4 channels at 300 MHz data rate, no interpolation, and using mix mode to stress the second and third Nyquist zones (150-300 MHz and 300-450 MHz). Please contact M-Labs if you need help with this.
 
 The hardware required is a KC705 with an AD9154-FMC-EBZ plugged into the HPC connector and a low-noise sample rate reference clock.
 
@@ -72,6 +72,8 @@ Setup
 
     python -m artiq.gateware.targets.phaser
 
+* From time to time and on request there may be pre-built binaries in the
+  ``artiq-kc705-phaser`` package on the M-Labs conda package label.
 * Generate an ARTIQ configuration flash image with MAC and IP address (see the
   documentation for ``artiq_mkfs``). Name it ``phaser_config.bin``.
 * Run the following OpenOCD command to flash the ARTIQ phaser design: ::
@@ -89,6 +91,8 @@ Setup
 * Refer to the ARTIQ documentation to configure an IP address and other settings for the transmitter device.
   If the board was running stock ARTIQ before, the settings will be kept.
 * A 300 MHz clock of roughly 10 dBm (0.2 to 3.4 V peak-to-peak into 50 Ohm) must be connected to the AD9154-FMC-EBZ J1. The input is 50 Ohm terminated. The RTIO clock, DAC deviceclock, FPGA deviceclock, and SYSREF are derived from this signal.
+* The RTIO coarse clock (the rate of the RTIO timestamp counter) is 150
+  MHz. The RTIO ``ref_period`` is 1/150 MHz = 5ns/6. The RTIO ``ref_multiplier`` is ``1``. C.f. ``device_db.py`` for both variables. The JED204B DAC data rate and DAC device clock are both 300 MHz. The JESD204B line rate is 6 GHz.
 * Configure an oscilloscope to trigger at 0.5 V on rising edge of ttl_sma (user_gpio_n on the KC705 board). Monitor DAC0 (J17) on the oscilloscope set for 100 mV/div and 200 ns/div.
 * An example device database, several status and test scripts are provided in ``artiq/examples/phaser/``. ::
 
diff --git a/artiq/coredevice/sawg.py b/artiq/coredevice/sawg.py
index 540a209fc..ba8c39951 100644
--- a/artiq/coredevice/sawg.py
+++ b/artiq/coredevice/sawg.py
@@ -239,8 +239,12 @@ class SAWG:
     This parametrization can be viewed as two complex (quadrature) oscillators
     (``frequency1``/``phase1`` and ``frequency2``/``phase2``) that are
     executing and sampling at the coarse RTIO frequency. They can represent
-    frequencies within their first Nyquist zone from ``-f_RTIO/2`` to
-    ``f_RTIO/2``.
+    frequencies within the first Nyquist zone from ``-f_rtio_coarse/2`` to
+    ``f_rtio_coarse/2``.
+
+    .. note:: The coarse RTIO frequency ``f_rtio_coarse`` is the inverse of
+      ``ref_period*multiplier``. Both are arguments of the ``Core`` device,
+      specified in the device database ``device_db.py``.
 
     The sum of their outputs is then interpolated by a factor of
     :attr:`parallelism` (2, 4, 8 depending on the bitstream) using a
@@ -251,10 +255,10 @@ class SAWG:
 
     After the limiter, the data is shifted in frequency using a complex
     digital up-converter (DUC, ``frequency0``/``phase0``) running at
-    :attr:`parallelism` times the coarse RTIO frequency. The first Nyquist zone
-    of the DUC extends from ``-f_RTIO*parallelism/2`` to
-    ``f_RTIO*parallelism/2``. Other Nyquist zones are usable depending on the
-    interpolation/modulation options configured in the DAC.
+    :attr:`parallelism` times the coarse RTIO frequency. The first Nyquist
+    zone of the DUC extends from ``-f_rtio_coarse*parallelism/2`` to
+    ``f_rtio_coarse*parallelism/2``. Other Nyquist zones are usable depending
+    on the interpolation/modulation options configured in the DAC.
 
     The real/in-phase data after digital up-conversion can be offset using
     another spline interpolator ``offset``.