Update hardware instructions to better match real testing processes

Signed-off-by: Egor Savkin <es@m-labs.hk>
This commit is contained in:
Egor Savkin 2024-03-19 15:02:07 +08:00
parent 9323039e6a
commit 387e2f85e4
10 changed files with 53 additions and 41 deletions

View File

@ -2,16 +2,16 @@
"nodes": { "nodes": {
"nixpkgs": { "nixpkgs": {
"locked": { "locked": {
"lastModified": 1697851979, "lastModified": 1710695816,
"narHash": "sha256-lJ8k4qkkwdvi+t/Xc6Fn74kUuobpu9ynPGxNZR6OwoA=", "narHash": "sha256-3Eh7fhEID17pv9ZxrPwCLfqXnYP006RKzSs0JptsN84=",
"owner": "NixOS", "owner": "NixOS",
"repo": "nixpkgs", "repo": "nixpkgs",
"rev": "5550a85a087c04ddcace7f892b0bdc9d8bb080c8", "rev": "614b4613980a522ba49f0d194531beddbb7220d3",
"type": "github" "type": "github"
}, },
"original": { "original": {
"owner": "NixOS", "owner": "NixOS",
"ref": "nixos-23.05", "ref": "nixos-23.11",
"repo": "nixpkgs", "repo": "nixpkgs",
"type": "github" "type": "github"
} }

View File

@ -1,7 +1,7 @@
{ {
description = "Sinara assembly and test instructions"; description = "Sinara assembly and test instructions";
inputs.nixpkgs.url = github:NixOS/nixpkgs/nixos-23.05; inputs.nixpkgs.url = github:NixOS/nixpkgs/nixos-23.11;
outputs = { self, nixpkgs }: outputs = { self, nixpkgs }:

View File

@ -13,8 +13,8 @@
"hw_rev": "vX.Y", // optional "hw_rev": "vX.Y", // optional
"ports": [<port num>], "ports": [<port num>],
"edge_counter": <bool>, "edge_counter": <bool>,
"bank_direction_low": "input", "bank_direction_low": "input", // or "output"
"bank_direction_high": "output" "bank_direction_high": "output" // or "input"
} }
``` ```

View File

@ -4,20 +4,11 @@
## JSON ## JSON
Put the `ext_ref_frequency` field into the JSON description if the Kasli is going to use an external frequency: Not present in the JSON.
```json Peripherals typically should choose `"clk_sel": 2` for MMCX connection and `"clk_sel": 1` for external SMA connection.
{ Refer to the [official docs](https://m-labs.hk/artiq/manual/core_drivers_reference.html) by searching for `clk_sel`.
"hw_rev": "<hw rev>", You may also need to add `"refclk": <number>` field to the target card.
"base": "<base>",
...
"ext_ref_frequency": <freq in Hz>,
...
"peripherals": [...]
}
```
On peripherals you should choose `"clk_sel": 2` on connected devices.
## Setup external clocker ## Setup external clocker
@ -41,12 +32,12 @@ Here is example setup for SynthNV RF signal generator:
1. Switch `CLK SEL` pin to `EXT`/`INT` according to customer needs 1. Switch `CLK SEL` pin to `EXT`/`INT` according to customer needs
2. Connect MMCx cables according to the customer needs and boards specifications (see image below for reference): 2. Connect MMCx cables according to the customer needs and boards specifications (see image below for reference):
if the `INT` source is chosen, connect MMCx cable to `INT CLK`, otherwise connect external clocker to SMA `EXT CLK` if the `INT` source is chosen, connect MMCx cable to `INT CLK`, otherwise connect external clocker to SMA `EXT CLK`
3. Connect the Clocker to the Kasli via 30-pin ports 3. Connect the Clocker to the Kasli via 30-pin ports, or via external power supply
![](../img/clocker_ref.jpg) ![](../img/clocker_ref.jpg)
4. Connect the Clocker's SMA output to the Kasli's `CLK`/`CLK IN` SMA pin 4. Connect the Clocker's SMA output to the Kasli's `CLK`/`CLK IN` SMA pin
5. After assembling the crates and flashing the firmware, start Kasli and write config as follows: 5. After assembling the crates and flashing the firmware, start Kasli and set config if needed:
`artiq_coremgmt config write -s rtio_clock ext0_bypass`. Please refer to the [official manual](https://m-labs.hk/artiq/manual/installing.html#miscellaneous-configuration-of-the-core-device) `artiq_coremgmt config write -s rtio_clock ext0_bypass`. Please refer to the [official manual](https://m-labs.hk/artiq/manual/installing.html#miscellaneous-configuration-of-the-core-device)
for the details and available options for the details and available options. In most cases you may skip this step.
6. Reboot either via `artiq_coremgmt reboot` or via power supply if the board's firmware doesn't have such command 6. Reboot either via `artiq_coremgmt reboot` or via power supply if the board's firmware doesn't have such command
## Testing ## Testing

View File

@ -9,7 +9,9 @@
{ {
"type": "mirny", "type": "mirny",
"almazny": true, // for mirny with almazny only "almazny": true, // for mirny with almazny only
"ports": [<port num>] "ports": [<port num>],
"clk_sel": 2, // optional
"refclk": 125e6 // optional
} }
``` ```
@ -37,8 +39,8 @@ mirny0_ch3 info: {'f_outA': 1300000000.0, 'f_outB': 10400000000, 'output_divider
After running `artiq_sinara_test`: After running `artiq_sinara_test`:
1. Install gqrx `nix-shell -p gqrx` 1. Install gqrx `nix-shell -p gqrx`
2. Connect bladeRF via USB cable only 2. Connect HackRF One via USB cable only
3. Run gqrx and choose `BladeRF #<number>...` 3. Run gqrx and choose `HackRF HackRF One...`
4. Default settings 4. Default settings
5. When gqrx loaded, start DSP processing with frequency at mirnyN_chM freq 5. When gqrx loaded, start DSP processing with frequency at mirnyN_chM freq
6. Connect the probe through attenuator to the Mirny's port 6. Connect the probe through attenuator to the Mirny's port

View File

@ -25,9 +25,9 @@ phaser0 10+0 10+1 10+2 10+3 10+4 MHz
### Upconverter ### Upconverter
1. Install gqrx `nix-shell -p gqrx` 1. Install gqrx `nix-shell -p gqrx`
2. Connect bladeRF via USB cable only 2. Connect HackRF One via USB cable only
3. Run gqrx and choose `Nuand bladeRF SN <number>...` 3. Run gqrx and choose `HackRF HackRF One...`
4. Input rate 20000000, other settings are default 4. Default settings
5. Lower the gain in `Input options` 5. Lower the gain in `Input options`
6. When gqrx loaded, start DSP processing with frequency near 2.875 GHz +- DUC frequencies from `artiq_sinara_test` 6. When gqrx loaded, start DSP processing with frequency near 2.875 GHz +- DUC frequencies from `artiq_sinara_test`
in `Receiver Options` in `Receiver Options`
@ -39,11 +39,7 @@ phaser0 10+0 10+1 10+2 10+3 10+4 MHz
### Baseband ### Baseband
1. Install gqrx `nix-shell -p gqrx` 1. Connect the probe through attenuator to the Phaser's ports RF0 or RF1 (not the ADC)
2. Connect bladeRF via USB cable only 2. Find FTT (Fourier Transform) function in the oscilloscope
3. Run gqrx and choose `Nuand bladeRF SN <number>...` 3. Start processing with frequency near DUC frequencies from `artiq_sinara_test`
4. Input rate 15000000, other settings are default 4. You should see 5 tones on `artiq_sinara_test`'s frequencies
5. When gqrx loaded, start DSP processing with frequency near 2.875 GHz (???)
6. Connect the probe through attenuator to the Phaser's ports RF0 or RF1 (not the ADC)
7. You should see 5 tones on `artiq_sinara_test`'s frequencies (???):
![phaser_baseband.png](../img/phaser_baseband.png)

View File

@ -33,3 +33,4 @@ PASSED
1. Apply 1.5V (connect the AA-battery) to the `samplerX`'s requested channel 1. Apply 1.5V (connect the AA-battery) to the `samplerX`'s requested channel
2. Press `Enter`, the `artiq_sinara_test` should output `PASSED` 2. Press `Enter`, the `artiq_sinara_test` should output `PASSED`
3. Repeat steps 1-2 for every available channel. 3. Repeat steps 1-2 for every available channel.
4. Disassemble AA-battery tool as it risks getting corrosion

View File

@ -23,6 +23,28 @@ dfu-util -a 0 -s 0x08000000:leave -D thermostat.bin
Then check that fans are working properly. Then check that fans are working properly.
You may also check fan controls via `fan` commands (see the firmware documentation). You may also check fan controls via `fan` commands (see the firmware documentation).
## Test PID
1. For Zotino: connect 10-pins IDC 2.54mm FC cable from internal Thermostat connector to the Zotino TEC
2. General TEC: connect external connector to the TEC
3. Connect Ethernet and PSU
4. Run:
```shell
git clone gitea@git.m-labs.hk:esavkin/thermostat.git
cd thermostat
git checkout zotino-tec
nix develop
python pytec/tec_qt.py
```
5. In `Output Config`, set limits:
* `Max Cooling Current` - 400 mA
* `Max Heating Current` - 400 mA
* `Max Voltage Difference` - 1 V
6. `PID Config` -> `PID Auto Tune` set desired target temperature, which should be slightly above your room temperature (+10C)
7. Set `Thermistor Config` -> `B` and other values, according to the datasheet of the TEC module, for example for Zotino `B` is `3455 K`
8. Run `PID Config` -> `PID Auto Tune` -> `Run` and check graphs that the measured temperature goes to the target temperature,
and eventually stabilizes at +- 0.01 of the target
## Common problems ## Common problems
### Thermostat doesn't connect or doesn't enter DFU mode ### Thermostat doesn't connect or doesn't enter DFU mode

View File

@ -20,7 +20,8 @@
## Setup ## Setup
Check if [SUServo](./suservo.md) is enabled/disabled respective to customer needs. Connect to the clocker source. Check if [SUServo](./suservo.md) is enabled/disabled respective to customer needs. Connect to the clock source - either Clocker,
Kasli or external via SMA.
### Synchronization ### Synchronization

View File

@ -20,8 +20,7 @@
} }
``` ```
Fastino uses two physical EEM channels, but in the JSON file there should be only one channel specified, Fastino uses one physical EEM channel, despite having two EEM ports.
and it should be the one connected to Fastino's EEM0.
## Setup ## Setup