ARTIQ Zynq-based core device support
Go to file
mwojcik aebc739c1e add support for tar flashable (sub)kernels 2023-11-13 11:24:23 +08:00
examples qc2: add 4 edge counters to the end of rtio 2023-04-03 12:25:07 +08:00
src add support for tar flashable (sub)kernels 2023-11-13 11:24:23 +08:00
.gitignore force cargo to use our copy of zynq-rs 2023-10-09 18:27:58 +08:00
LICENSE add license 2020-07-20 19:44:45 +08:00
README.md force cargo to use our copy of zynq-rs 2023-10-09 18:27:58 +08:00
demo.json add Kasli-SoC demo JSON 2021-02-15 19:51:46 +08:00
flake.lock flake: update dependencies 2023-11-07 18:54:31 +08:00
flake.nix add support for tar flashable (sub)kernels 2023-11-13 11:24:23 +08:00
kasli-soc-master.json update build scripts for DRTIO 2021-10-08 16:25:13 +08:00
kasli-soc-satellite.json update build scripts for DRTIO 2021-10-08 16:25:13 +08:00
local_run.sh local_run: fix artiq_netbook invokation 2022-01-27 18:58:26 +08:00
remote_run.sh update build scripts for DRTIO 2021-10-08 16:25:13 +08:00

README.md

ARTIQ on Zynq

How to use

  1. Install the ARTIQ version that corresponds to the artiq-zynq version you are targeting.
  2. To obtain firmware binaries, select the latest successful build on Hydra for the targeted artiq-zynq version, or use AFWS. If using Hydra, search for the job named <board>-<variant>-sd (for example: zc706-nist_clock-sd or zc706-nist_qc2-sd).
  3. Place the boot.bin file, obtained from Hydra's "binary distribution" download link or from AFWS, at the root of a FAT-formatted SD card.
  4. Optionally, create a config.txt configuration file at the root of the SD card containing key=value pairs on each line. Use the ip, ip6 and mac keys to respectively set the IPv4, IPv6 and MAC address of the board. Configuring an IPv6 address is entirely optional. If these keys are not found, the firmware will use default values that may or may not be compatible with your network.
  5. Insert the SD card into the board and set up the board to boot from the SD card. For the ZC706, this is achieved by placing the large DIP switch SW11 in the 00110 position.
  6. Power up the board. After the firmware starts successfully, it should respond to ping at its IP addresses, and boot messages can be observed from its UART at 115200bps.
  7. Create and use an ARTIQ device database as usual, but set "target": "cortexa9" in the arguments of the core device.

Configuration

Configuring the device is done using the config.txt text file at the root of the SD card, plus the contents of the config folder. When searching for a configuration key, the firmware first looks for a file named /config/[key].bin and, if it exists, returns the contents of that file. If not, it looks into /config.txt, which contains a list of key=value pairs, one per line. The config folder allows configuration values that consist in binary data, such as the startup kernel.

The following configuration keys are available:

  • mac: Ethernet MAC address.
  • ip: IPv4 address.
  • ip6: IPv6 address.
  • startup: startup kernel in ELF format (as produced by artiq_compile).
  • rtio_clock: source of RTIO clock; valid values are ext0_bypass and int_125.
  • boot: SD card "boot.bin" file, for replacing the boot firmware/gateware. Write only.

Configurations can be read/written/removed via artiq_coremgmt. Config erase is not implemented as it seems not very useful.

Development instructions

ARTIQ on Zynq is packaged using the Nix Flakes system. Install Nix 2.8+ and enable flakes by adding experimental-features = nix-command flakes to nix.conf (e.g. ~/.config/nix/nix.conf).

Pure build with Nix and execution on a remote JTAG server:

nix build .#zc706-nist_clock-jtag  # or zc706-nist_qc2-jtag or zc706-nist_clock_satellite-jtag etc.
./remote_run.sh

Impure incremental build and execution on a remote JTAG server:

nix develop
cd src
gateware/zc706.py -g ../build/gateware -V <variant> # build gateware
make GWARGS="-V <variant>" <runtime/satman>    # build firmware
cd ..
./remote_run.sh -i

Notes:

  • The impure build process is also compatible with non-Nix systems.
  • When calling make, you need to specify both the variant and firmware type.
  • Firmware type must be either runtime for DRTIO-less or DRTIO master variants, or satman for DRTIO satellite.
  • If the board is connected to the local machine, use the local_run.sh script.

License

Copyright (C) 2019-2023 M-Labs Limited.

ARTIQ is free software: you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.

ARTIQ is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.

You should have received a copy of the GNU Lesser General Public License along with ARTIQ. If not, see http://www.gnu.org/licenses/.