Add instruction for Mirny

Signed-off-by: Egor Savkin <es@m-labs.hk>

src/SUMMARY.md

@@ -1,4 +1,6 @@
 # Summary
 
 - [Build and test firmware](./build_test_firmware.md)
-- [Sinara 4624 AWG Phaser (Upconverter)](./hw/phaser_upconverter.md)
+- [Hardware](./hw/hardware.md)
+  - [Sinara 4624 AWG Phaser (Upconverter)](./hw/phaser_upconverter.md)
+  - [Sinara 4456 synthesizer Mirny](./hw/mirny.md)

src/hw/hardware.md

@@ -0,0 +1,4 @@
+# Hardware
+
+In this section you will find instructions on testing the hardware.
+If you didn't find one for your hardware, feel free to compose and add your instruction.

src/hw/mirny.md

@@ -0,0 +1,42 @@
+# Sinara 4456 synthesizer Mirny
+
+## JSON
+
+```json
+{
+  "type": "mirny",
+  "ports": [<port num>]
+}
+```
+
+## Testing
+
+```text
+*** Testing Mirny PLLs.
+Initializing CPLDs...
+mirny0_cpld...
+...done
+All mirny channels active.
+Frequencies:
+mirny0_ch0	1000MHz
+mirny0_ch0 info: {'f_outA': 1000000000.0, 'f_outB': 8000000000, 'output_divider': 4, 'f_vco': 4000000000, 'pll_n': 40, 'pll_frac1': 0, 'pll_frac2': 0, 'pll_mod2': 1, 'prescaler': '4/5', 'sysclk': 100000000.0, 'ref_doubler': False, 'ref_divider': False, 'ref_counter': 1, 'f_pfd': 100000000}
+mirny0_ch1	1100MHz
+mirny0_ch1 info: {'f_outA': 1100000000.0, 'f_outB': 8800000000, 'output_divider': 4, 'f_vco': 4400000000, 'pll_n': 44, 'pll_frac1': 0, 'pll_frac2': 0, 'pll_mod2': 1, 'prescaler': '4/5', 'sysclk': 100000000.0, 'ref_doubler': False, 'ref_divider': False, 'ref_counter': 1, 'f_pfd': 100000000}
+mirny0_ch2	1200MHz
+mirny0_ch2 info: {'f_outA': 1200000000.0, 'f_outB': 9600000000, 'output_divider': 4, 'f_vco': 4800000000, 'pll_n': 48, 'pll_frac1': 0, 'pll_frac2': 0, 'pll_mod2': 1, 'prescaler': '4/5', 'sysclk': 100000000.0, 'ref_doubler': False, 'ref_divider': False, 'ref_counter': 1, 'f_pfd': 100000000}
+mirny0_ch3	1300MHz
+mirny0_ch3 info: {'f_outA': 1300000000.0, 'f_outB': 10400000000, 'output_divider': 4, 'f_vco': 5200000000, 'pll_n': 52, 'pll_frac1': 0, 'pll_frac2': 0, 'pll_mod2': 1, 'prescaler': '4/5', 'sysclk': 100000000.0, 'ref_doubler': False, 'ref_divider': False, 'ref_counter': 1, 'f_pfd': 100000000}
+```
+
+After running `artiq_sinara_test`:
+
+1. Install gqrx `nix-shell -p gqrx`
+2. Connect bladeRF via USB cable only
+3. Run gqrx and choose `BladeRF #<number>...`
+4. Default settings
+5. When gqrx loaded, start DSP processing with frequency at mirnyN_chM freq
+6. Connect the probe through attenuator to the Mirny's port
+7. You should see significant signal emission on choosen freq compared to nearby freqs (see image below)
+8. Repeat 5-7 for every channel
+
+![](../img/mirny_gqrx.png)

src/hw/phaser_upconverter.md

@@ -25,7 +25,7 @@ After running `artiq_sinara_test`:
 3. Run gqrx and choose `BladeRF #<number>...`
 4. Input rate 30000000, other settings are default
 5. When gqrx loaded, start DSP processing with frequency near 2.875 GHz + frequencies from `artiq_sinara_test` in `Receiver Options`
-6. Connect the probe with adjusted resistance (???) to the Phaser's ports
+6. Connect the probe through attenuator to the Phaser's ports
 7. You should see 5 tones on `artiq_sinara_test`'s frequencies, like on the picture below
 
 ![](../img/phaser_upconverter_gqrx.png)