linuswck commented on issue sinara-hw/kirdy#32

2024-02-06 15:40:55 +08:00

MCU's Firmware Starts before Analog Power Rails are "Power Good"

Yes. Should be a simple bug fix in code depending hw revision.

linuswck opened issue sinara-hw/kirdy#32

2024-02-06 14:49:42 +08:00

MCU's Firmware starts before Analog Power Rails are "Power Good"

linuswck pushed to master at sinara-hw/kirdy

2024-02-05 14:43:24 +08:00

c08d3d36b4 Panel: Add Mounting Plates for Fiber Optic Adapters

c7cfa18a99 sch: Add M3 Washer to BOM

Compare 2 commits »

linuswck pushed to master at M-Labs/kirdy

2024-02-02 17:38:45 +08:00

4132bfacd3 boot: Set thermostat & LD init output current to 0

linuswck pushed to master at M-Labs/kirdy

2024-02-02 17:36:57 +08:00

4f44925bb7 boot: Turn off thermostat and LD by default

6096711d2c eth: Poll and Handle Json based Ld ctrl cmd

3d3d6f5cb5 ld: cleanup

Compare 3 commits »

linuswck pushed to master at M-Labs/kirdy

2024-02-01 16:25:06 +08:00

172c3e1dfc cleanup boot.rs, thermostat.rs

ee0ed8ebe7 eth: add drivers for init, polling & sending data

771f2813f7 gpio: correct wrong eth pin definition

4e0d14def2 laser: Add driver and fn to get termination status

Compare 4 commits »

linuswck opened issue sinara-hw/kirdy#31

2024-01-29 16:24:36 +08:00

Fiber optic adapter mounted on front panel may block the access of alternate programming pin header

linuswck pushed to master at M-Labs/kirdy

2024-01-26 16:57:24 +08:00

f6677d874c LD: Rst LD current at power_up for soft start

d391e3a1fb LD: Setting LD output current now ramps up slowly

edd30e94a0 laser_diode: Add fn to set pd_dark_i

ad731c2f15 rename pd_mon -> pd_responsitivity

9d8a553669 pd_mon: add fns to convert between pwr and current

Compare 10 commits »

linuswck pushed to master at M-Labs/kirdy

2024-01-24 12:29:01 +08:00

07ea733b34 thermostst: Patch hw related settings for rev0_3

linuswck pushed to master at M-Labs/kirdy

2024-01-24 12:20:23 +08:00

5bea3f0e5f boot: init analog wdg & power up laser after cfg

af283b17ac laser_diode: use analog wdg fns

c3022e9db1 Analog_Wdg: Add GPIO init

c02181c80c laser diode: Add Analog Watchdog initial commit

095fe8ea69 AD7172: Rm deprecated warning for Rev0_2 hw bug

Compare 21 commits »

linuswck commented on issue sinara-hw/kirdy#29

2024-01-24 11:27:09 +08:00

components bump into card guides

I will correct it in a future commit along with a Rule Area added for the edge rail.

linuswck commented on issue sinara-hw/kirdy#30

2024-01-24 11:04:52 +08:00

[Rev0_3] Front Panel is connected to PCB Ground

It is indeed not an issue and does not affect the low noise signal path.

linuswck pushed to master at sinara-hw/kirdy

2024-01-24 10:56:55 +08:00

43c5afefab sch: correct MFR/PNs for BSS138, TLV9001, TPS54620

linuswck closed issue sinara-hw/kirdy#30

2024-01-24 10:55:34 +08:00

[Rev0_3] Front Panel is connected to PCB Ground

linuswck opened issue sinara-hw/kirdy#30

2024-01-24 10:48:45 +08:00

[Rev0_3] Front Panel is connected to PCB Ground

linuswck pushed to master at M-Labs/kirdy

2024-01-16 16:16:23 +08:00

e355e83d28 memory.x: Add comment on the reserved flash sector

linuswck commented on issue sinara-hw/kirdy#20

2024-01-16 12:39:41 +08:00

[TEST] Turn on / Turn off behavior

Laser Driver Output (Without Load)

Objective

To check open circuit voltage

Test Setup

Kirdy Hardware: Rev0_2

Added Rev0_3 the soft start circuit at 12V Power Input

Kirdy…

linuswck commented on issue sinara-hw/kirdy#20

2024-01-16 11:24:27 +08:00

[TEST] Turn on / Turn off behavior

Laser Driving Output

Objective

To see if there is current spikes appear on the laser driver output at startup and check if abnormal behavior

Test Setup

Kirdy Hardware: Rev0_2 -…

linuswck pushed to master at M-Labs/kirdy

2024-01-15 17:45:00 +08:00

285fc9b5d6 memory.x: Reserved Flash Sector 11 for Config

8c612fc0c9 memory.x: RM CONFIG MEMORY area in linker script

Compare 2 commits »

linuswck pushed to master at M-Labs/kirdy

2024-01-15 17:23:31 +08:00

42cd55645c main: Add demo fns to use on-board flash

d190b8b192 flash: Add init boot seq

74325a3cee flash: Add fns to store data in flash

Compare 3 commits »