current source working

.gitignore

@@ -1,2 +1,4 @@
 target/
 result
+
+*.jdebug*

src/device/boot.rs

@@ -6,18 +6,15 @@ use stm32f4xx_hal::{
 };
 use fugit::ExtU32;
 use log::info;
-use super::{log_setup, sys_timer, usb};
-use super::gpio;
-use crate::laser_diode::current_sources;
+use super::{log_setup, sys_timer, usb, gpio};
+use crate::laser_diode::current_sources::*;
 
 #[cfg(not(feature = "semihosting"))]
 const WATCHDOG_PERIOD: u32 = 1000;
 #[cfg(feature = "semihosting")]
 const WATCHDOG_PERIOD: u32 = 30000;
 
-pub fn bootup (mut core_perif : CorePeripherals, perif : Peripherals) -> (
-    IndependentWatchdog
-) {
+pub fn bootup (mut core_perif : CorePeripherals, perif : Peripherals) -> IndependentWatchdog {
 
     log_setup::init_log();
     info!("Kirdy init");
@@ -35,9 +32,12 @@ pub fn bootup (mut core_perif : CorePeripherals, perif : Peripherals) -> (
         .pclk2(MegaHertz::from_raw(64).convert())
         .freeze();
 
-    let (eth_pins,
-         usb,
-         current_source) = gpio::setup(
+    sys_timer::setup(core_perif.SYST, clocks);
+
+    let (
+        eth_pins,
+        usb,
+        current_source_phy) = gpio::setup(
         clocks, perif.TIM4,
         perif.GPIOA, perif.GPIOB, perif.GPIOC, perif.GPIOD, perif.GPIOE, perif.GPIOF, perif.GPIOG,
         perif.SPI1, perif.SPI2, perif.SPI3,
@@ -45,14 +45,24 @@ pub fn bootup (mut core_perif : CorePeripherals, perif : Peripherals) -> (
         perif.OTG_FS_GLOBAL, perif.OTG_FS_DEVICE, perif.OTG_FS_PWRCLK,
     );
 
+    usb::State::setup(usb);
+
+    let mut laser = current_source {
+        phy: current_source_phy,
+        setting: current_source_settings_construct {
+            output_current : 0.0
+        }
+    };
+
+    laser.setup();
+    laser.set_current(0.1);
+    
     let mut wd = IndependentWatchdog::new(perif.IWDG);
     wd.start(WATCHDOG_PERIOD.millis());
     wd.feed();
 
-    sys_timer::setup(core_perif.SYST, clocks);
-
     info!("Kirdy setup complete");
 
-    (wd)
+    wd
 
 }

src/device/gpio.rs

@@ -52,7 +52,7 @@ pub fn setup(
 ) -> (  
     EthernetPins, 
     USB, 
-    current_source_construct<current_source_0>, 
+    current_source_phy_construct<current_source_phy_ch0>, 
     // photo_diode_phy, 
     // thermostat_phy 
 ) {
@@ -84,29 +84,23 @@ pub fn setup(
         rx_d1: gpioc.pc5,
     };
     
-    let sck = gpiob.pb10.into_alternate();
-    let mosi = gpiob.pb15.into_alternate();
-    let mode = spi::Mode {
-        polarity: spi::Polarity::IdleHigh,
-        phase: spi::Phase::CaptureOnSecondTransition,
-    };
-    let spi2 = Spi::new(
-        spi2, 
-        (sck, NoMiso {}, mosi), 
-        mode, 
-        10_u32.MHz(), 
-        &clocks);
-
-    
-    let current_source: current_source_construct<current_source_0> = current_source_construct {
-        max5719_spi: spi2,
-        max5719_load: gpioe.pe4.into_push_pull_output(),
-        current_source_ldo_en: gpioe.pe10.into_push_pull_output(),
-        current_source_short: gpioa.pa4.into_push_pull_output(),
-        output_current: 0.0
+    let current_source_phy = current_source_phy_construct {  
+        max5719_spi: Spi::new(
+            spi2, 
+            (gpiob.pb10.into_alternate(), NoMiso {}, gpiob.pb15.into_alternate()), 
+            spi::Mode {
+                polarity: spi::Polarity::IdleLow,
+                phase: spi::Phase::CaptureOnFirstTransition,
+            }, 
+            10_u32.MHz(), 
+            &clocks),
+        max5719_load: gpiob.pb14.into_push_pull_output(),   
+        max5719_cs: gpiod.pd8.into_push_pull_output(),     
+        current_source_ldo_en: gpiod.pd9.into_push_pull_output(),
+        current_source_short: gpioa.pa4.into_push_pull_output()
     };
     
-    (eth_pins, usb, current_source)
+    (eth_pins, usb, current_source_phy)
 
 }
 

src/laser_diode/current_sources.rs

@@ -5,37 +5,73 @@ use stm32f4xx_hal::{
         gpioa::*,
         gpiob::*,
         gpioe::*,
+        gpiod::*,
         Output, 
-        PushPull,
+        PushPull, PD9,
     },
-    hal::{self, blocking::spi::Transfer, digital::v2::OutputPin},
+    hal::{self, blocking::spi::Write, digital::v2::OutputPin},
     spi::{Spi, NoMiso, TransferModeNormal},
     pac::SPI2,
 };
 
+use crate::device::sys_timer::sleep;
 pub trait current_source_phy {
-    type max5719_spi: Transfer<u8>;
-    type max5719_load: OutputPin;
     type current_source_ldo_en: OutputPin;
     type current_source_short: OutputPin;
+    type max5719_load: OutputPin;
+    type max5719_cs: OutputPin;
+    type max5719_spi: Write<u8>;
 }
 
-pub struct current_source_construct<C: current_source_phy> {
+pub struct current_source_phy_construct<C: current_source_phy> {
     pub max5719_spi: C::max5719_spi,
     pub max5719_load: C::max5719_load,
+    pub max5719_cs: C::max5719_cs,
     pub current_source_ldo_en: C::current_source_ldo_en,
     pub current_source_short: C::current_source_short,
-    pub output_current : f32,
+}
+pub struct current_source_settings_construct {
+    pub output_current: f32
+}
+pub struct current_source<C:current_source_phy> {
+    pub phy : current_source_phy_construct<C>,
+    pub setting: current_source_settings_construct
 }
 
-pub struct current_source_0;
+pub struct current_source_phy_ch0;
 
-impl current_source_phy for current_source_0 {
-    type max5719_spi = Spi<SPI2, (PB10<Alternate<5>>, NoMiso, PB15<Alternate<5>>), TransferModeNormal>;
-    type max5719_load = PE4<Output<PushPull>>;
-    type current_source_ldo_en = PE10<Output<PushPull>>;
+impl current_source_phy for current_source_phy_ch0 {
+    type current_source_ldo_en = PD9<Output<PushPull>>;
     type current_source_short = PA4<Output<PushPull>>;
+    type max5719_load = PB14<Output<PushPull>>;
+    type max5719_cs = PD8<Output<PushPull>>;
+    type max5719_spi = Spi<SPI2, (PB10<Alternate<5>>, NoMiso, PB15<Alternate<5>>), TransferModeNormal>;
 }
 
+impl<C:current_source_phy> current_source<C>  {
 
+    pub fn setup(&mut self) {
+        self.phy.max5719_load.set_high();
+        self.phy.max5719_cs.set_high();
+        self.phy.current_source_ldo_en.set_high();
+        sleep(50_u32);
+        self.phy.current_source_short.set_high();
+        sleep(50_u32);
+    }
 
+    pub fn set_current(&mut self, current: f32) {
+        self.phy.max5719_load.set_high();
+        self.phy.max5719_cs.set_low();
+        let v_dac = current * 10.0 / 0.75;
+        let word = (((v_dac / 4.096) * 1048576.0) as u32) << 4;
+        let mut buf = [
+            ((word >> 16) & 0xFF) as u8,
+            ((word >> 8) & 0xFF) as u8,
+            ((word >> 0) & 0xFF) as u8,
+        ];
+        self.phy.max5719_spi.write(&mut buf);
+        self.phy.max5719_cs.set_high();
+        self.phy.max5719_load.set_low();
+    }
+
+}

src/laser_diode/max5719.rs

@@ -1,17 +0,0 @@
-use stm32f4xx_hal::{
-    adc::Adc,
-    gpio::{
-        AF5, Alternate, Analog, Input,
-        gpioa::*,
-        gpiob::*,
-        gpiod::*,
-        Output, PushPull, Pin,
-    },
-    hal::{self, blocking::spi::Transfer, digital::v2::OutputPin},
-    spi::{Spi, NoMiso, TransferModeNormal},
-    pac::{GPIOB, SPI2}
-};
-
-
-
-