From 2fe2ef531b82b79d7552bc26076afc02e722a29d Mon Sep 17 00:00:00 2001 From: linuswck Date: Tue, 3 Sep 2024 10:36:49 +0800 Subject: [PATCH] Update example code --- pykirdy/asyncio_exmaple.py | 178 +++++++++++++++++-------------------- 1 file changed, 83 insertions(+), 95 deletions(-) diff --git a/pykirdy/asyncio_exmaple.py b/pykirdy/asyncio_exmaple.py index 7b7e954..9587c1e 100644 --- a/pykirdy/asyncio_exmaple.py +++ b/pykirdy/asyncio_exmaple.py @@ -2,147 +2,135 @@ from pprint import pp from driver.kirdy import Kirdy, FilterConfig import signal import time +import asyncio -""" - Enter Device Firmware Upgrade(Dfu) mode - Please see README.md for flash instructions. -""" -def enter_dfu_mode(kirdy: Kirdy): - kirdy.device.dfu() - kirdy.end_session() +async def enter_dfu_mode(kirdy: Kirdy): + """ + Enter Device Firmware Upgrade(Dfu) mode + Please refer to README.md for firmware update instructions. + """ + await kirdy.device.dfu() -""" - Configure Kirdy to actively report status - Press Ctrl + C to exit active report mode -""" -def active_report(kirdy: Kirdy): - class SignalHandler: - def __init__(self): - signal.signal(signal.SIGINT, self.exit_gracefully) - signal.signal(signal.SIGTERM, self.exit_gracefully) - def exit_gracefully(self, signum, frame): - kirdy.stop_report_mode() - - signal_handler = SignalHandler() - - for data in kirdy.get_report_stream(): +async def active_report(kirdy: Kirdy): + """ + Configure Kirdy to actively report status to connected socket + Press Ctrl + C to exit active report mode + """ + async for data in kirdy.report_mode(): pp(data) -""" - Configure Kirdy network and board specific transconductance settings. - These configs are saved to flash immediately after command is processed. -""" -def device_cfg(kirdy: Kirdy): +async def device_cfg(kirdy: Kirdy): + """ + Configure Kirdy's network and board specific transconductance settings. + These configs are saved to flash immediately after command is processed. + """ # Kirdy rev0_3's gain and transconductance varies between boards to maximize the # PD current range resolution. - kirdy.device.set_pd_mon_fin_gain(1.0) - kirdy.device.set_pd_mon_transconductance(1/1000.0) + await kirdy.device.set_pd_mon_fin_gain(1.0) + await kirdy.device.set_pd_mon_transconductance(1/1000.0) # Network Settings will be updated on next reboot. - kirdy.device.set_ip_settings( + await kirdy.device.set_ip_settings( addr="192.168.1.128", port=1337, prefix_len=24, gateway="192.168.1.1" ) # Hard reset Kirdy. - kirdy.device.hard_reset() + await kirdy.device.hard_reset() -""" - Control and config laser diode and thermostat parameters. -""" -def ld_thermostat_cfg(kirdy: Kirdy): - # Load the laser diode and thermostat settings from flash - kirdy.device.restore_settings_from_flash() +async def ld_thermostat_cfg(kirdy: Kirdy): + """ + Control and config laser diode and thermostat parameters. + """ + # Load the laser diode and thermostat settings from flash memory. + await kirdy.device.restore_settings_from_flash() - # Power off the laser diode and thermostat and clear alarm (if any) - kirdy.laser.set_power_on(False) - kirdy.laser.clear_alarm() - kirdy.thermostat.set_power_on(False) - kirdy.thermostat.clear_alarm() + # Power off the laser diode & thermostat and clear any asserted alarm + await kirdy.laser.set_power_on(False) + await kirdy.laser.clear_alarm() + await kirdy.thermostat.set_power_on(False) + await kirdy.thermostat.clear_alarm() # Set the laser diode terminals not to be shorted - kirdy.laser.set_ld_terms_short(False) + await kirdy.laser.set_ld_terms_short(False) # Do not power up the laser & thermostat during initial startup - kirdy.laser.set_default_pwr_on(False) - kirdy.thermostat.set_default_pwr_on(False) + await kirdy.laser.set_default_pwr_on(False) + await kirdy.thermostat.set_default_pwr_on(False) - kirdy.laser.set_i(0) + await kirdy.laser.set_i(0) # Configure the laser diode output power limit and photodiode parameters - # Exceeding the measured power limit triggers overpower protection alarm. - # The laser diode power will be turned off while the thermostat power remains unchanged. - kirdy.laser.set_ld_pwr_limit(0.0) - kirdy.laser.set_pd_mon_dark_current(0.0) - kirdy.laser.set_pd_mon_responsitivity(0.0) + # Exceeding the power limit triggers overpower protection alarm. + # The laser diode power will be cut off upon alarm assertion while the thermostat power remains unchanged. + await kirdy.laser.set_ld_pwr_limit(0.0) + await kirdy.laser.set_pd_mon_dark_current(0.0) + await kirdy.laser.set_pd_mon_responsitivity(0.0) # Configure the thermostat NTC thermistor parameters. - kirdy.thermostat.set_sh_r0(10.0 * 1000) - kirdy.thermostat.set_sh_t0(25) - kirdy.thermostat.set_sh_beta(3900) + await kirdy.thermostat.set_sh_r0(10.0 * 1000) + await kirdy.thermostat.set_sh_t0(25) + await kirdy.thermostat.set_sh_beta(3900) - # Configure the thermostat output limits. - # The actual output current is limited by the hardware limit set below. - kirdy.thermostat.set_tec_max_cooling_i(1.0) - kirdy.thermostat.set_tec_max_heating_i(1.0) - kirdy.thermostat.set_tec_max_v(4.0) + # Configure the thermostat TEC settings. + # The actual output current is limited by value set below. + await kirdy.thermostat.set_tec_max_cooling_i(1.0) + await kirdy.thermostat.set_tec_max_heating_i(1.0) + await kirdy.thermostat.set_tec_max_v(4.0) - # Configure the thermostat temperature monitor limit. - # Exceeding the limit will trigger over temperature protection alarm. - # The laser diode and thermostat power will be turned off. - kirdy.thermostat.set_temp_mon_upper_limit(70) - kirdy.thermostat.set_temp_mon_lower_limit(0) + # Configure the thermostat temperature monitor limits. + # Exceeding the temperature limits trigger over temperature protection alarm. + # Both laser diode and thermostat power will be cut off upon alarm assertion. + await kirdy.thermostat.set_temp_mon_upper_limit(70) + await kirdy.thermostat.set_temp_mon_lower_limit(0) - # Configure the thermostat PID related parameter. - # You can configure the PID parameter with the autotune tool. - # Here provides an example if it is configured manually. - kirdy.thermostat.set_temperature_setpoint(25) - kirdy.thermostat.set_pid_kp(0.15668282198105507) - kirdy.thermostat.set_pid_ki(0.002135962407793784) - kirdy.thermostat.set_pid_kd(0.829254515277143) - kirdy.thermostat.set_pid_output_max(1.0) - kirdy.thermostat.set_pid_output_min(-1.0) + # Configure the thermostat PID parameters. + # You can configure the PID parameter by the included autotune script. + await kirdy.thermostat.set_temperature_setpoint(25) + await kirdy.thermostat.set_pid_kp(0.15668282198105507) + await kirdy.thermostat.set_pid_ki(0.002135962407793784) + await kirdy.thermostat.set_pid_kd(0.829254515277143) + await kirdy.thermostat.set_pid_output_max(1.0) + await kirdy.thermostat.set_pid_output_min(-1.0) # Configure the thermostat ADC Filter Setting / PID Update Rate / Report Rate. # The ADC sampling rate determines the report and pid update rate. # The chosen filter and sampling rate affects the noise of the readings. - # For details, please refer to the AD7172 da`tas`heet. - kirdy.thermostat.config_temp_adc_filter(FilterConfig.Sinc5Sinc1With50hz60HzRejection.f16sps) + # For details, please refer to the AD7172 datasheet. + await kirdy.thermostat.config_temp_adc_filter(FilterConfig.Sinc5Sinc1With50hz60HzRejection.f16sps) # Configure thermostat to run in PID control mode - kirdy.thermostat.set_pid_control_mode() + await kirdy.thermostat.set_pid_control_mode() # When control mode is switched from PID to constant current(CC) control mode, - # the thermostat keeps its instantaneous output current unchanged. + # thermostat keeps its instantaneous output current unchanged. # Thermostat output current should only be set if it is in CC control mode - # or the value set will not be overwritten by PID output. - kirdy.thermostat.set_constant_current_control_mode() - kirdy.thermostat.set_tec_i_out(0.0) + # or the value set will be overwritten by PID output. + await kirdy.thermostat.set_constant_current_control_mode() + await kirdy.thermostat.set_tec_i_out(0.0) - # Save the above settings configured into the flash - kirdy.device.save_current_settings_to_flash() + # Save the current settings to flash memory + await kirdy.device.save_current_settings_to_flash() # Power on the laser diode and thermostat - kirdy.laser.set_power_on(True) - kirdy.thermostat.set_power_on(True) + await kirdy.laser.set_power_on(True) + await kirdy.thermostat.set_power_on(True) - pp(kirdy.device.get_settings_summary()) - pp(kirdy.device.get_status_report()) + pp(await kirdy.device.get_settings_summary()) + pp(await kirdy.device.get_status_report()) -def main(): +async def main(): kirdy = Kirdy() kirdy.start_session(host='192.168.1.128', port=1337) + await kirdy.wait_until_connected() - while not(kirdy.connected()): - pass - - ld_thermostat_cfg(kirdy) - # active_report(kirdy) + await ld_thermostat_cfg(kirdy) + # await active_report(kirdy) # await device_cfg(kirdy) - # enter_dfu_mode(kirdy) + # await enter_dfu_mode(kirdy) - kirdy.end_session(block=True) + await kirdy.end_session() if __name__ == "__main__": - main() + asyncio.run(main())