hartytp
/
ionpak-thermostat
forked from M-Labs/ionpak-thermostat
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

remove other ionpak artifacts

This commit is contained in:
Sebastien Bourdeauducq 2019-07-31 13:16:38 +08:00
parent 3fe5aae04e
commit 2fcae2cdee
132 changed files with 0 additions and 178621 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

9
hardware/assembly.md
View File

@ -1,9 +0,0 @@
Assembly notes
==============
Flyback transformer construction
--------------------------------
TR300: Use EPCOS coilformer B66208X1010T1. Wind 5 turns on the primary and spread them across the length of the coilformer - it is particularly important that the air gap between the cores is covered by windings. Wind 70 turns on the secondary in multiple layers. As with all flyback transformers, the polarity of the windings is critical. Assemble with EPCOS cores B66317G500X127 and B66317GX127 (one half gapped core, one half ungapped core), and corresponding clips.
TR350: Use EPCOS coilformer B66206W1110T1 and cores B66311G250X127 and B66311GX127. Both the primary and the secondary have 5 turns and must be wound together, interleaving the windings. The same remarks as for TR300 apply.

50
hardware/errata.md
View File

@ -1,50 +0,0 @@
Hardware errata
===============
Rev 1
-----
* R307 needs more clearance from D400
* Pins 1 and 12 of U502 need pull-downs
* Pin 1 of U501 needs pull-up
* D203 reversed polarity
* R236 and R234 are swapped
* Q301 needs to be NPN, change to BC817
* increase R307 -> 3.3Kohm and increase R500 -> 33Kohm
* C201: oscillates at 0 and 1nF, stable at 100nF
* add clamp diodes to GND on op-amp outputs to ADC when op-amp has negative supply
* R214 -> 7.5k
* LM339PT is in TSSOP package. Change for SOIC P/N
* GDT200 minimum firing voltage is too low
* the relay model should be changed to 9001-05-00. 9001-05-02 is an undocumented normally closed variant.
* D504 should follow the schematics in its datasheet
* R502 should be connected to VCC
* R502 -> 240 ohm
* C500 -> 1nF
* R234 -> 7.5k
* Q104 -> DMN3404
* R114 -> 470 ohm
* R115 -> 4.7k
* R227 -> 470 ohm
* R228 -> 4.7k
* review values of R226 and R113
* C100 -> 47pF NP0 AVX, R107 -> 100K, C101 -> 0.1uF
* use crystal type recommended by the MCU datasheet
* add connector for OLED display?
* enlarge holes to fit M3 screws comfortably
* add 15M resistor between A and FIL-
* power U200 from a small negative voltage instead of GND
* review choice of filament flyback output diode
* invert LED position so that the Ethernet LED is closest to the connector
* invert polarity of LEDs (Ethernet LED polarity cannot be programmed)
* change D351 model to MBR1645
* add snubber on D351
* add heatsink (Seifert-KK633) to D351
* move D351 further away from transformer for heatsink clearance
* add plated-through holes and pads for mounting rods of BNC connector
* simplify FBI circuit, 2 ranges only (typ. 8mA and 45mA), remove diodes and neglect MOSFET leakage
* to support different case designs, replace the holes on the connectors side with slots. One of the case designs requires holes whose center is at 11.5mm from the board edge.
* review choice of external LED connector type and clearance
* if using a non-polarized connector, change pinout so that connecting the LEDs the wrong way cannot cause damage
* add 12V fan connector and on/off circuit (with optocoupler)
* increase sensitivity to ~20fA / LSB

BIN
hardware/rev1/IONPAK1_250417_1.pdf
View File

Binary file not shown.

4659
hardware/rev1/gerber/IONPAK1-B.Cu.gbr
View File

File diff suppressed because it is too large Load Diff

260
hardware/rev1/gerber/IONPAK1-B.Mask.gbr
View File

@ -1,260 +0,0 @@
G04 #@! TF.FileFunction,Soldermask,Bot*
%FSLAX46Y46*%
G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
G04 Created by KiCad (PCBNEW 4.0.2-stable) date 5/1/2017 12:34:54 AM*
%MOMM*%
G01*
G04 APERTURE LIST*
%ADD10C,0.100000*%
%ADD11C,1.998980*%
%ADD12R,1.998980X1.998980*%
%ADD13R,1.300000X1.300000*%
%ADD14C,1.300000*%
%ADD15C,1.700000*%
%ADD16R,1.700000X1.700000*%
%ADD17R,1.727200X1.727200*%
%ADD18O,1.727200X1.727200*%
%ADD19O,3.600000X2.500000*%
%ADD20R,3.600000X2.500000*%
%ADD21O,2.500000X3.600000*%
%ADD22R,2.500000X3.600000*%
%ADD23C,1.600000*%
%ADD24O,1.600000X1.600000*%
%ADD25C,2.400000*%
%ADD26O,2.400000X2.400000*%
%ADD27C,2.400000*%
%ADD28C,3.750000*%
%ADD29C,1.250000*%
%ADD30R,2.100000X3.600000*%
%ADD31O,2.100000X3.600000*%
%ADD32O,1.700000X1.700000*%
%ADD33R,1.050000X1.050000*%
%ADD34C,1.050000*%
%ADD35C,3.000000*%
%ADD36C,8.000000*%
%ADD37R,1.800000X1.800000*%
%ADD38C,1.800000*%
%ADD39R,1.800000X3.600000*%
%ADD40O,1.800000X3.600000*%
%ADD41C,2.200000*%
%ADD42C,2.800000*%
%ADD43R,5.800000X5.800000*%
%ADD44C,5.500000*%
%ADD45C,1.500000*%
%ADD46C,2.100000*%
G04 APERTURE END LIST*
D10*
X248893000Y-224500000D02*
G75*
G03X248893000Y-224500000I-1143000J0D01*
G01*
X254389000Y-227000000D02*
G75*
G03X254389000Y-227000000I-889000J0D01*
G01*
X249889000Y-227000000D02*
G75*
G03X249889000Y-227000000I-889000J0D01*
G01*
X255893000Y-224500000D02*
G75*
G03X255893000Y-224500000I-1143000J0D01*
G01*
D11*
X156464000Y-226824540D03*
D12*
X166624000Y-226824540D03*
D13*
X131826000Y-192024000D03*
D14*
X136826000Y-192024000D03*
D13*
X234696000Y-202438000D03*
D14*
X239696000Y-202438000D03*
D13*
X210566000Y-184912000D03*
D14*
X210566000Y-179912000D03*
D15*
X180340000Y-217250000D03*
D16*
X180340000Y-222250000D03*
D15*
X195580000Y-217250000D03*
D16*
X195580000Y-222250000D03*
D13*
X178054000Y-201422000D03*
D14*
X183054000Y-201422000D03*
D17*
X134620000Y-179832000D03*
D18*
X134620000Y-177292000D03*
X134620000Y-174752000D03*
X134620000Y-169672000D03*
X134620000Y-167132000D03*
X134620000Y-164592000D03*
X134620000Y-162052000D03*
D19*
X208026000Y-209804000D03*
X208026000Y-205994000D03*
X218186000Y-209804000D03*
X218186000Y-205994000D03*
X208026000Y-202184000D03*
X208026000Y-198374000D03*
D20*
X208026000Y-194564000D03*
D19*
X218186000Y-194564000D03*
X218186000Y-198374000D03*
X218186000Y-202184000D03*
D21*
X146558000Y-203962000D03*
X151638000Y-203962000D03*
X146558000Y-216662000D03*
X151638000Y-216662000D03*
X156718000Y-203962000D03*
X161798000Y-203962000D03*
D22*
X166878000Y-203962000D03*
D21*
X166878000Y-216662000D03*
X161798000Y-216662000D03*
X156718000Y-216662000D03*
D23*
X217932000Y-219202000D03*
D24*
X207772000Y-219202000D03*
D25*
X207010000Y-225552000D03*
D26*
X222250000Y-225552000D03*
D23*
X157480000Y-223266000D03*
D24*
X167640000Y-223266000D03*
D25*
X246761000Y-191770000D03*
D27*
X257537307Y-180993693D02*
X257537307Y-180993693D01*
D23*
X232791000Y-194310000D03*
D24*
X232791000Y-184150000D03*
D23*
X241554000Y-194183000D03*
D24*
X241554000Y-184023000D03*
D28*
X308356000Y-231902000D03*
D29*
X299466000Y-223012000D03*
D28*
X296924000Y-231902000D03*
D29*
X302006000Y-223012000D03*
X304546000Y-223012000D03*
X307086000Y-223012000D03*
X298196000Y-225552000D03*
X300736000Y-225552000D03*
X303276000Y-225552000D03*
X305816000Y-225552000D03*
D30*
X131000000Y-226000000D03*
D31*
X136080000Y-226000000D03*
D21*
X238160000Y-226080000D03*
X233080000Y-226080000D03*
D22*
X228000000Y-226080000D03*
X228000000Y-221000000D03*
D21*
X233080000Y-221000000D03*
X238160000Y-221000000D03*
D16*
X280924000Y-223266000D03*
D32*
X283464000Y-223266000D03*
X286004000Y-223266000D03*
X288544000Y-223266000D03*
X291084000Y-223266000D03*
D16*
X290322000Y-197866000D03*
D32*
X290322000Y-200406000D03*
X290322000Y-202946000D03*
X290322000Y-205486000D03*
X290322000Y-208026000D03*
X290322000Y-210566000D03*
D33*
X314198000Y-181864000D03*
D34*
X314198000Y-183134000D03*
X314198000Y-184404000D03*
X314198000Y-185674000D03*
X314198000Y-186944000D03*
X315468000Y-183134000D03*
X315468000Y-184404000D03*
X315468000Y-185674000D03*
X315468000Y-186944000D03*
X315468000Y-181864000D03*
D35*
X121000000Y-229000000D03*
X121000000Y-158000000D03*
X315000000Y-158000000D03*
D36*
X315000000Y-229000000D03*
D37*
X289000000Y-227000000D03*
D38*
X291540000Y-227000000D03*
D37*
X283000000Y-227000000D03*
D38*
X285540000Y-227000000D03*
D37*
X145000000Y-227000000D03*
D38*
X147540000Y-227000000D03*
D13*
X178054000Y-186944000D03*
D14*
X183054000Y-186944000D03*
D39*
X130810000Y-219456000D03*
D40*
X135890000Y-219456000D03*
D41*
X247750000Y-224500000D03*
X254750000Y-224500000D03*
D15*
X249000000Y-227000000D03*
X253500000Y-227000000D03*
D35*
X218000000Y-161000000D03*
D38*
X260286500Y-212153500D03*
X255206500Y-212153500D03*
D42*
X250126500Y-212153500D03*
D43*
X265366500Y-212153500D03*
D38*
X260286500Y-205359000D03*
X255206500Y-205359000D03*
D42*
X250126500Y-205359000D03*
D43*
X265366500Y-205359000D03*
D44*
X268000000Y-220620000D03*
D45*
X270540000Y-220620000D03*
D46*
X273080000Y-225700000D03*
X262920000Y-225700000D03*
M02*

11
hardware/rev1/gerber/IONPAK1-B.SilkS.gbr
View File

@ -1,11 +0,0 @@
G04 #@! TF.FileFunction,Legend,Bot*
%FSLAX46Y46*%
G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
G04 Created by KiCad (PCBNEW 4.0.2-stable) date 5/1/2017 12:34:54 AM*
%MOMM*%
G01*
G04 APERTURE LIST*
%ADD10C,0.100000*%
G04 APERTURE END LIST*
D10*
M02*

13151
hardware/rev1/gerber/IONPAK1-F.Cu.gbr
View File

File diff suppressed because it is too large Load Diff

2229
hardware/rev1/gerber/IONPAK1-F.Mask.gbr
View File

File diff suppressed because it is too large Load Diff

16777
hardware/rev1/gerber/IONPAK1-F.SilkS.gbr
View File

File diff suppressed because it is too large Load Diff

7758
hardware/rev1/gerber/IONPAK1-In1.Cu.gbr
View File

File diff suppressed because it is too large Load Diff

2040
hardware/rev1/gerber/IONPAK1-In2.Cu.gbr
View File

File diff suppressed because it is too large Load Diff

21
hardware/rev1/gerber/IONPAK1-Margin.gbr
View File

@ -1,21 +0,0 @@
G04 #@! TF.FileFunction,Other,User*
%FSLAX46Y46*%
G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
G04 Created by KiCad (PCBNEW 4.0.2-stable) date 5/1/2017 12:34:54 AM*
%MOMM*%
G01*
G04 APERTURE LIST*
%ADD10C,0.100000*%
%ADD11C,0.200000*%
G04 APERTURE END LIST*
D10*
D11*
X115000000Y-235000000D02*
X115000000Y-152000000D01*
X321000000Y-235000000D02*
X115000000Y-235000000D01*
X321000000Y-152000000D02*
X321000000Y-235000000D01*
X115000000Y-152000000D02*
X321000000Y-152000000D01*
M02*

1304
hardware/rev1/gerber/IONPAK1-NPTH-drl_map.gbr
View File

File diff suppressed because it is too large Load Diff

25
hardware/rev1/gerber/IONPAK1-NPTH.drl
View File

@ -1,25 +0,0 @@
M48
;DRILL file {KiCad 4.0.2-stable} date 4/26/2017 8:44:01 AM
;FORMAT={-:-/ absolute / inch / decimal}
FMAT,2
INCH,TZ
T1C0.083
T2C0.118
T3C0.128
%
G90
G05
M72
T1
X10.3512Y-8.8858
X10.7512Y-8.8858
T2
X4.7638Y-6.2205
X4.7638Y-9.0157
X8.5827Y-6.3386
X12.4016Y-6.2205
T3
X11.6899Y-9.13
X12.14Y-9.13
T0
M30

5785
hardware/rev1/gerber/IONPAK1-drl_map.gbr
View File

File diff suppressed because it is too large Load Diff

415
hardware/rev1/gerber/IONPAK1.drl
View File

@ -1,415 +0,0 @@
M48
;DRILL file {KiCad 4.0.2-stable} date 4/26/2017 8:44:01 AM
;FORMAT={-:-/ absolute / inch / decimal}
FMAT,2
INCH,TZ
T1C0.016
T2C0.026
T3C0.030
T4C0.031
T5C0.035
T6C0.039
T7C0.039
T8C0.040
T9C0.047
T10C0.050
T11C0.051
T12C0.055
T13C0.063
T14C0.118
%
G90
G05
M72
T1
X5.79Y-7.42
X5.82Y-7.
X5.82Y-7.39
X5.83Y-7.44
X5.85Y-7.41
X5.85Y-7.47
X5.86Y-7.61
X5.86Y-7.71
X5.86Y-7.79
X5.86Y-7.88
X5.86Y-8.84
X5.88Y-7.3
X5.88Y-7.4
X5.88Y-7.44
X5.96Y-7.88
X6.02Y-7.05
X6.09Y-7.88
X6.19Y-6.54
X6.68Y-7.54
X6.68Y-7.58
X6.68Y-7.62
X6.73Y-7.54
X6.73Y-7.58
X6.73Y-7.62
X6.78Y-7.54
X6.78Y-7.58
X6.78Y-7.62
X7.44Y-7.99
X7.44Y-8.06
X7.44Y-8.11
X7.45Y-7.42
X7.47Y-8.03
X7.47Y-8.08
X7.48Y-6.6
X7.49Y-7.98
X7.51Y-8.01
X7.51Y-8.06
X7.51Y-8.1
X7.57Y-7.42
X7.59Y-8.36
X7.61Y-8.4
X7.63Y-8.36
X7.64Y-7.14
X7.64Y-7.18
X7.65Y-8.4
X7.66Y-6.96
X7.67Y-8.36
X7.68Y-6.98
X7.69Y-8.4
X7.7Y-6.96
X7.71Y-8.36
X7.72Y-6.98
X7.74Y-6.66
X7.74Y-6.96
X7.88Y-8.09
X7.97Y-8.08
X7.97Y-8.17
X8.06Y-7.98
X8.06Y-8.08
X8.66Y-6.72
X8.66Y-7.22
X8.66Y-8.51
X8.7Y-8.46
X8.75Y-8.465
X8.8Y-8.46
X8.835Y-8.51
X9.03Y-6.21
X9.135Y-6.78
X9.21Y-6.56
X9.28Y-7.02
X9.29Y-6.94
X9.32Y-7.29
X9.33Y-6.775
X9.33Y-6.865
X9.33Y-6.94
X9.35Y-7.29
X9.38Y-7.02
X9.39Y-6.51
X9.48Y-6.4
X9.49Y-6.3
X9.54Y-6.82
X9.56Y-6.61
X9.58Y-6.24
X9.58Y-6.37
X9.65Y-6.73
X9.706Y-8.209
X9.71Y-8.49
X9.7318Y-7.2018
X9.7615Y-6.751
X9.77Y-7.91
X9.88Y-7.65
X9.89Y-7.7
X9.9Y-7.76
X9.9Y-7.83
X9.94Y-6.72
X9.94Y-6.77
X9.97Y-7.83
X10.Y-6.72
X10.Y-6.77
X10.04Y-7.74
X10.06Y-6.49
X10.13Y-6.39
X10.16Y-6.24
X10.19Y-6.27
X10.21Y-7.03
X10.21Y-7.75
X10.26Y-7.8
X10.29Y-7.03
X10.29Y-7.08
X10.32Y-7.39
X10.35Y-7.46
X10.38Y-6.44
X10.41Y-7.25
X10.435Y-7.02
X10.46Y-7.73
X10.52Y-7.46
X10.56Y-7.73
X10.59Y-7.61
X10.6Y-7.45
X10.68Y-7.58
X10.73Y-7.455
X10.7375Y-7.865
X10.79Y-7.185
X10.8055Y-7.453
X10.8085Y-7.3785
X10.82Y-6.38
X10.82Y-7.69
X10.86Y-6.46
X10.8865Y-7.395
X10.9Y-6.26
X10.9Y-6.31
X10.9Y-7.57
X10.94Y-6.31
X10.94Y-6.47
X10.94Y-8.68
X11.Y-9.03
X11.005Y-7.345
X11.0075Y-7.277
X11.02Y-7.23
X11.023Y-6.489
X11.03Y-8.47
X11.035Y-7.105
X11.055Y-7.25
X11.08Y-7.53
X11.085Y-7.71
X11.1Y-6.25
X11.1Y-7.632
X11.1275Y-7.8625
X11.14Y-7.38
X11.15Y-6.45
X11.174Y-6.885
X11.188Y-6.583
X11.21Y-6.77
X11.21Y-6.81
X11.21Y-7.6
X11.21Y-7.71
X11.215Y-7.36
X11.2395Y-6.4325
X11.28Y-6.33
X11.28Y-7.53
X11.28Y-8.33
X11.283Y-6.568
X11.295Y-7.06
X11.3195Y-6.628
X11.32Y-6.31
X11.33Y-7.88
X11.33Y-8.1
X11.36Y-6.59
X11.39Y-6.18
X11.39Y-7.06
X11.431Y-7.351
X11.46Y-6.44
X11.47Y-6.57
X11.53Y-6.25
X11.551Y-7.741
X11.57Y-6.77
X11.579Y-7.9975
X11.58Y-6.59
X11.59Y-6.55
X11.613Y-7.277
X11.621Y-7.124
X11.622Y-7.056
X11.6255Y-6.605
X11.636Y-7.215
X11.648Y-8.0185
X11.665Y-7.858
X11.667Y-6.15
X11.675Y-8.17
X11.677Y-7.6965
X11.69Y-6.74
X11.701Y-7.121
X11.742Y-7.463
X11.7465Y-6.9865
X11.759Y-7.2745
X11.764Y-7.788
X11.788Y-7.406
X11.79Y-6.8425
X11.825Y-7.403
X11.828Y-7.858
X11.835Y-7.369
X11.838Y-8.018
X11.85Y-6.88
X11.854Y-6.981
X11.858Y-7.872
X11.86Y-6.63
X11.862Y-7.4895
X11.885Y-7.902
X11.89Y-6.44
X11.895Y-8.17
X11.905Y-7.93
X11.91Y-6.74
X11.9175Y-7.2785
X11.93Y-8.02
X11.9465Y-7.055
X11.95Y-7.84
X11.97Y-6.35
X11.97Y-7.38
X11.995Y-7.405
X12.Y-6.75
X12.02Y-7.43
X12.024Y-7.6405
X12.04Y-6.87
X12.04Y-8.09
X12.041Y-7.7505
X12.0495Y-7.1845
X12.05Y-6.76
X12.062Y-7.2355
X12.075Y-7.7755
X12.078Y-7.407
X12.089Y-7.2085
X12.091Y-7.167
X12.0945Y-7.7035
X12.11Y-6.88
X12.1115Y-6.7425
X12.113Y-7.0985
X12.12Y-6.48
X12.1435Y-7.7345
X12.1545Y-7.5015
X12.17Y-7.6725
X12.1745Y-7.5335
X12.175Y-7.888
X12.18Y-8.185
X12.18Y-8.24
X12.184Y-7.344
X12.198Y-7.8425
X12.2Y-6.695
X12.2035Y-7.553
X12.2075Y-6.9385
X12.219Y-7.3765
X12.24Y-7.641
X12.293Y-7.995
X12.308Y-8.16
X12.313Y-7.4735
X12.3135Y-8.089
X12.328Y-7.8
X12.34Y-8.2
X12.38Y-7.04
X12.419Y-8.206
X12.42Y-7.04
X12.5Y-7.57
X12.514Y-7.8595
T2
X12.37Y-7.16
X12.37Y-7.21
X12.37Y-7.26
X12.37Y-7.31
X12.37Y-7.36
X12.42Y-7.16
X12.42Y-7.21
X12.42Y-7.26
X12.42Y-7.31
X12.42Y-7.36
T3
X11.74Y-8.88
X11.79Y-8.78
X11.84Y-8.88
X11.89Y-8.78
X11.94Y-8.88
X11.99Y-8.78
X12.04Y-8.88
X12.09Y-8.78
T4
X5.19Y-7.56
X5.3869Y-7.56
X6.2Y-8.79
X6.6Y-8.79
X7.01Y-7.36
X7.01Y-7.93
X7.2069Y-7.36
X7.2069Y-7.93
X8.18Y-8.63
X8.29Y-7.0831
X8.29Y-7.28
X8.58Y-8.63
X9.165Y-7.25
X9.165Y-7.65
X9.24Y-7.97
X9.4369Y-7.97
X9.51Y-7.245
X9.51Y-7.645
X9.8475Y-8.085
X9.8475Y-8.3525
X10.0475Y-8.085
X10.0475Y-8.3525
X10.2475Y-8.085
X10.2475Y-8.3525
X10.4475Y-8.085
X10.4475Y-8.3525
T5
X5.7087Y-8.937
X5.8087Y-8.937
X10.5512Y-8.6858
X10.6512Y-8.6858
X11.1417Y-8.937
X11.2417Y-8.937
X11.378Y-8.937
X11.478Y-8.937
T6
X9.8031Y-8.937
X9.9803Y-8.937
X11.06Y-8.79
X11.16Y-8.79
X11.26Y-8.79
X11.36Y-8.79
X11.43Y-7.79
X11.43Y-7.89
X11.43Y-7.99
X11.43Y-8.09
X11.43Y-8.19
X11.43Y-8.29
X11.46Y-8.79
T7
X6.56Y-8.9301
T8
X5.3Y-6.38
X5.3Y-6.48
X5.3Y-6.58
X5.3Y-6.68
X5.3Y-6.88
X5.3Y-6.98
X5.3Y-7.08
T9
X5.15Y-8.64
X5.35Y-8.64
X7.1Y-8.5531
X7.1Y-8.75
X7.7Y-8.5531
X7.7Y-8.75
X8.15Y-8.88
X8.75Y-8.88
X9.715Y-7.55
X10.1393Y-7.1257
T10
X6.16Y-8.9301
T11
X8.19Y-7.81
X8.19Y-7.96
X8.19Y-8.11
X8.19Y-8.26
X8.59Y-7.66
X8.59Y-7.81
X8.59Y-7.96
X8.59Y-8.11
X8.59Y-8.26
X9.7539Y-8.8386
X10.0295Y-8.8386
T12
X5.1575Y-8.8976
X5.3575Y-8.8976
T13
X5.77Y-8.03
X5.77Y-8.53
X5.97Y-8.03
X5.97Y-8.53
X6.17Y-8.03
X6.17Y-8.53
X6.37Y-8.03
X6.37Y-8.53
X6.57Y-8.03
X6.57Y-8.53
X8.19Y-7.66
X8.9764Y-8.7008
X8.9764Y-8.9008
X9.1764Y-8.7008
X9.1764Y-8.9008
X9.3764Y-8.7008
X9.3764Y-8.9008
T14
X12.4016Y-9.0157
T0
M30

BIN
hardware/rev1/ionpak_bom_rev1.xls
View File

Binary file not shown.

1156
hardware/rev1/kicad/IONPAK1-cache.lib
View File

File diff suppressed because it is too large Load Diff

15286
hardware/rev1/kicad/IONPAK1.kicad_pcb
View File

File diff suppressed because it is too large Load Diff

4068
hardware/rev1/kicad/IONPAK1.net
View File

File diff suppressed because it is too large Load Diff

72
hardware/rev1/kicad/IONPAK1.pro
View File

@ -1,72 +0,0 @@
update=4/25/2017 11:39:52 PM
version=1
last_client=kicad
[pcbnew]
version=1
LastNetListRead=
UseCmpFile=1
PadDrill=0.600000000000
PadDrillOvalY=0.600000000000
PadSizeH=1.500000000000
PadSizeV=1.500000000000
PcbTextSizeV=1.500000000000
PcbTextSizeH=1.500000000000
PcbTextThickness=0.300000000000
ModuleTextSizeV=1.000000000000
ModuleTextSizeH=1.000000000000
ModuleTextSizeThickness=0.150000000000
SolderMaskClearance=0.000000000000
SolderMaskMinWidth=0.000000000000
DrawSegmentWidth=0.200000000000
BoardOutlineThickness=0.100000000000
ModuleOutlineThickness=0.150000000000
[cvpcb]
version=1
NetIExt=net
[general]
version=1
[eeschema]
version=1
LibDir=
[eeschema/libraries]
LibName1=power
LibName2=device
LibName3=transistors
LibName4=conn
LibName5=linear
LibName6=regul
LibName7=74xx
LibName8=cmos4000
LibName9=adc-dac
LibName10=memory
LibName11=xilinx
LibName12=microcontrollers
LibName13=dsp
LibName14=microchip
LibName15=analog_switches
LibName16=motorola
LibName17=texas
LibName18=intel
LibName19=audio
LibName20=interface
LibName21=digital-audio
LibName22=philips
LibName23=display
LibName24=cypress
LibName25=siliconi
LibName26=opto
LibName27=atmel
LibName28=contrib
LibName29=valves
LibName30=ionpak
LibName31=relays
[schematic_editor]
version=1
PageLayoutDescrFile=
PlotDirectoryName=
SubpartIdSeparator=0
SubpartFirstId=65
NetFmtName=Pcbnew
SpiceForceRefPrefix=0
SpiceUseNetNumbers=0
LabSize=60

6913
hardware/rev1/kicad/IONPAK1.sch
View File

File diff suppressed because it is too large Load Diff

5572
hardware/rev1/kicad/ionpak.lib
View File

File diff suppressed because it is too large Load Diff

16
hardware/rev1/kicad/proj_footprints.pretty/28F0121-0SR-10.kicad_mod
View File

@ -1,16 +0,0 @@
(module 28F0121-0SR-10 (layer F.Cu) (tedit 5825A986)
(fp_text reference REF** (at -0.2 -2.3) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value 28F0121-0SR-10 (at 0 2) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -2.1 -1) (end -2.1 -1.6) (layer F.SilkS) (width 0.15))
(fp_line (start -2.1 -1.6) (end 2.1 -1.6) (layer F.SilkS) (width 0.15))
(fp_line (start 2.1 -1.6) (end 2.1 -1) (layer F.SilkS) (width 0.15))
(fp_line (start -2.1 1.6) (end -2.1 1.1) (layer F.SilkS) (width 0.15))
(fp_line (start -2.1 1.6) (end 2.1 1.6) (layer F.SilkS) (width 0.15))
(fp_line (start 2.1 1.6) (end 2.1 1.1) (layer F.SilkS) (width 0.15))
(pad 1 smd rect (at -1.79 0) (size 2.77 1.47) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 1.79 0) (size 2.77 1.47) (layers F.Cu F.Paste F.Mask))
)

14
hardware/rev1/kicad/proj_footprints.pretty/3528RGB.kicad_mod
View File

@ -1,14 +0,0 @@
(module 3528RGB (layer F.Cu) (tedit 58B7D568)
(fp_text reference REF** (at 0 -2.4) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value LED3528RGB (at 0 3.1) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start 2.68 1.327) (end 2.68 2.127) (layer F.SilkS) (width 0.15))
(fp_line (start 1.791 2.127) (end 2.591 2.127) (layer F.SilkS) (width 0.15))
(pad 4 smd rect (at 1.5 -0.8) (size 1.5 1) (layers F.Cu F.Paste F.Mask))
(pad 1 smd rect (at 1.5 0.8) (size 1.5 1) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at -1.5 0.8) (size 1.5 1) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at -1.5 -0.8) (size 1.5 1) (layers F.Cu F.Paste F.Mask))
)

9
hardware/rev1/kicad/proj_footprints.pretty/3mm_EARTH.kicad_mod
View File

@ -1,9 +0,0 @@
(module NPTH_3mm_ID (layer F.Cu) (tedit 58F9BBE4)
(fp_text reference H4 (at 0 2.9) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value 3mm_Mounting_Hole (at 0 -2.7) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(pad 1 thru_hole circle (at 0 0) (size 8 8) (drill 3) (layers *.Cu *.Mask F.SilkS))
)

29
hardware/rev1/kicad/proj_footprints.pretty/6-SMD.kicad_mod
View File

@ -1,29 +0,0 @@
(module 6-SMD (layer F.Cu) (tedit 58F98D57)
(descr "6-300 smd shape")
(tags "smd cms 6smd")
(attr smd)
(fp_text reference REF** (at 0.381 -1.143) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value 6-SMD (at 0 0.762) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -5.08 -2.54) (end -5.08 2.54) (layer F.SilkS) (width 0.15))
(fp_line (start -5.08 2.54) (end 2.54 2.54) (layer F.SilkS) (width 0.15))
(fp_line (start 2.54 2.54) (end 2.54 -2.54) (layer F.SilkS) (width 0.15))
(fp_line (start 2.54 -2.54) (end -5.08 -2.54) (layer F.SilkS) (width 0.15))
(fp_line (start -5.08 -1.27) (end -3.81 -1.27) (layer F.SilkS) (width 0.15))
(fp_line (start -3.81 -1.27) (end -3.81 1.27) (layer F.SilkS) (width 0.15))
(fp_line (start -3.81 1.27) (end -5.08 1.27) (layer F.SilkS) (width 0.15))
(pad 1 smd rect (at -3.81 4.635) (size 1.78 1.52) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at -1.27 4.635) (size 1.78 1.52) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at 1.27 4.635) (size 1.78 1.52) (layers F.Cu F.Paste F.Mask))
(pad 4 smd rect (at 1.27 -4.635) (size 1.78 1.52) (layers F.Cu F.Paste F.Mask))
(pad 5 smd rect (at -1.27 -4.635) (size 1.78 1.52) (layers F.Cu F.Paste F.Mask))
(pad 6 smd rect (at -3.81 -4.635) (size 1.78 1.52) (layers F.Cu F.Paste F.Mask))
(model SMD_Packages.3dshapes/6-SMD.wrl
(at (xyz 0 0 0))
(scale (xyz 1 0.5 0.8))
(rotate (xyz 0 0 0))
)
)

25
hardware/rev1/kicad/proj_footprints.pretty/BOURNS-GDT-2051.kicad_mod
View File

@ -1,25 +0,0 @@
(module BOURNS-GDT-2051 (layer F.Cu) (tedit 553CF70D)
(attr smd)
(fp_text reference REF** (at 0 0) (layer F.SilkS)
(effects (font (size 0.8 0.8) (thickness 0.15)))
)
(fp_text value BOURNS-GDT-2051 (at 0 0) (layer F.Fab)
(effects (font (size 0.8 0.8) (thickness 0.15)))
)
(fp_line (start -3 -2) (end 3 -2) (layer F.Fab) (width 0.2))
(fp_line (start 3 -2) (end 3 2) (layer F.Fab) (width 0.2))
(fp_line (start 3 2) (end -3 2) (layer F.Fab) (width 0.2))
(fp_line (start -3 2) (end -3 -2) (layer F.Fab) (width 0.2))
(fp_line (start 1 -1.5) (end 1 1.5) (layer F.SilkS) (width 0.2))
(fp_line (start 1 1.5) (end 0 0) (layer F.SilkS) (width 0.2))
(fp_line (start 0 0) (end 1 -1.5) (layer F.SilkS) (width 0.2))
(fp_line (start -1 -1.5) (end -1 1.5) (layer F.SilkS) (width 0.2))
(fp_line (start -1 1.5) (end 0 0) (layer F.SilkS) (width 0.2))
(fp_line (start 0 0) (end -1 -1.5) (layer F.SilkS) (width 0.2))
(fp_line (start -3.25 -2.35) (end 3.25 -2.35) (layer F.CrtYd) (width 0.2))
(fp_line (start 3.25 -2.35) (end 3.25 2.35) (layer F.CrtYd) (width 0.2))
(fp_line (start 3.25 2.35) (end -3.25 2.35) (layer F.CrtYd) (width 0.2))
(fp_line (start -3.25 2.35) (end -3.25 -2.35) (layer F.CrtYd) (width 0.2))
(pad 1 smd rect (at -2.25 0) (size 1.5 4.2) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 2.25 0) (size 1.5 4.2) (layers F.Cu F.Paste F.Mask))
)

19
hardware/rev1/kicad/proj_footprints.pretty/BOURNS-GDT-2051_ns.kicad_mod
View File

@ -1,19 +0,0 @@
(module proj_footprints:BOURNS-GDT-2051 (layer F.Cu) (tedit 58FF4C19)
(attr smd)
(fp_text reference GDT100 (at 3.81 3.048) (layer F.SilkS)
(effects (font (size 0.8 0.8) (thickness 0.15)))
)
(fp_text value 2051-09 (at 0 0) (layer F.Fab)
(effects (font (size 0.8 0.8) (thickness 0.15)))
)
(fp_line (start -3 -2) (end 3 -2) (layer F.Fab) (width 0.2))
(fp_line (start 3 -2) (end 3 2) (layer F.Fab) (width 0.2))
(fp_line (start 3 2) (end -3 2) (layer F.Fab) (width 0.2))
(fp_line (start -3 2) (end -3 -2) (layer F.Fab) (width 0.2))
(fp_line (start -3.25 -2.35) (end 3.25 -2.35) (layer F.CrtYd) (width 0.2))
(fp_line (start 3.25 -2.35) (end 3.25 2.35) (layer F.CrtYd) (width 0.2))
(fp_line (start 3.25 2.35) (end -3.25 2.35) (layer F.CrtYd) (width 0.2))
(fp_line (start -3.25 2.35) (end -3.25 -2.35) (layer F.CrtYd) (width 0.2))
(pad 1 smd rect (at -2.25 0) (size 1.5 4.2) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 2.25 0) (size 1.5 4.2) (layers F.Cu F.Paste F.Mask))
)

35
hardware/rev1/kicad/proj_footprints.pretty/COTO-9001.kicad_mod
View File

@ -1,35 +0,0 @@
(module relay_9001 (layer F.Cu) (tedit 58F9BC5C)
(descr "relay, Coto 9001 series Reed")
(fp_text reference RLY*** (at 0 -4.1) (layer F.SilkS)
(effects (font (thickness 0.3048)))
)
(fp_text value relay_9001 (at 0 4.3) (layer F.SilkS)
(effects (font (thickness 0.3048)))
)
(fp_line (start -8.6 -3) (end -8.6 3) (layer F.SilkS) (width 0.3048))
(fp_line (start 0.8 0) (end 2.5 0) (layer F.SilkS) (width 0.3048))
(fp_line (start -2.5 0) (end -0.8 0) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 0.8) (end 0.8 -0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 -0.8) (end 0.8 -0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start 0.8 -0.8) (end 0.8 0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 0.8) (end 0.8 0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 0.8) (end -0.8 -0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start 1.5 -1.8) (end 7.6 -1.8) (layer F.SilkS) (width 0.3048))
(fp_line (start 7.6 -1.8) (end 7.6 0) (layer F.SilkS) (width 0.3048))
(fp_line (start -7.6 -1.8) (end -7.6 0) (layer F.SilkS) (width 0.3048))
(fp_line (start -7.6 -1.8) (end -1.1 -1.8) (layer F.SilkS) (width 0.3048))
(fp_line (start -1.1 -1.8) (end 1.5 -2.3) (layer F.SilkS) (width 0.3048))
(fp_line (start 10.3 -3) (end 10.3 3) (layer F.SilkS) (width 0.3048))
(fp_line (start -10.3 -3) (end -10.3 3) (layer F.SilkS) (width 0.3048))
(fp_line (start -10.3 3) (end 10.3 3) (layer F.SilkS) (width 0.3048))
(fp_line (start -10.3 -3) (end 10.3 -3) (layer F.SilkS) (width 0.3048))
(pad 2 thru_hole circle (at -2.54 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(pad 3 thru_hole circle (at 2.54 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(pad 4 thru_hole circle (at 7.62 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(pad 1 thru_hole circle (at -7.62 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(model walter/relay/relay_9001.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 0))
)
)

29
hardware/rev1/kicad/proj_footprints.pretty/COTO-9001_ns.kicad_mod
View File

@ -1,29 +0,0 @@
(module proj_footprints:COTO-9001 (layer F.Cu) (tedit 58FF4F8B)
(descr "relay, Coto 9001 series Reed")
(fp_text reference RL101 (at 11.8745 0.889 90) (layer F.SilkS)
(effects (font (thickness 0.3048)))
)
(fp_text value 9001-05-02 (at 0 4.3) (layer F.SilkS)
(effects (font (thickness 0.3048)))
)
(fp_line (start 0.8 0) (end 2.5 0) (layer F.SilkS) (width 0.3048))
(fp_line (start -2.5 0) (end -0.8 0) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 0.8) (end 0.8 -0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 -0.8) (end 0.8 -0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start 0.8 -0.8) (end 0.8 0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 0.8) (end 0.8 0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 0.8) (end -0.8 -0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start 1.5 -1.8) (end 7.6 -1.8) (layer F.SilkS) (width 0.3048))
(fp_line (start 7.6 -1.8) (end 7.6 0) (layer F.SilkS) (width 0.3048))
(fp_line (start -1.1 -1.8) (end 1.5 -2.3) (layer F.SilkS) (width 0.3048))
(fp_line (start 10.3 -3) (end 10.3 3) (layer F.SilkS) (width 0.3048))
(pad 2 thru_hole circle (at -2.54 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(pad 3 thru_hole circle (at 2.54 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(pad 4 thru_hole circle (at 7.62 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(pad 1 thru_hole rect (at -7.62 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(model walter/relay/relay_9001.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 0))
)
)

29
hardware/rev1/kicad/proj_footprints.pretty/C_1206_ns.kicad_mod
View File

@ -1,29 +0,0 @@
(module Capacitors_SMD:C_1206 (layer F.Cu) (tedit 58FF4D39)
(descr "Capacitor SMD 1206, reflow soldering, AVX (see smccp.pdf)")
(tags "capacitor 1206")
(attr smd)
(fp_text reference C100 (at 5.208549 1.796051) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value DNP/1206 (at 0 2) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text user %R (at 0 -1.75) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -1.6 0.8) (end -1.6 -0.8) (layer F.Fab) (width 0.1))
(fp_line (start 1.6 0.8) (end -1.6 0.8) (layer F.Fab) (width 0.1))
(fp_line (start 1.6 -0.8) (end 1.6 0.8) (layer F.Fab) (width 0.1))
(fp_line (start -1.6 -0.8) (end 1.6 -0.8) (layer F.Fab) (width 0.1))
(fp_line (start -2.25 -1.05) (end 2.25 -1.05) (layer F.CrtYd) (width 0.05))
(fp_line (start -2.25 -1.05) (end -2.25 1.05) (layer F.CrtYd) (width 0.05))
(fp_line (start 2.25 1.05) (end 2.25 -1.05) (layer F.CrtYd) (width 0.05))
(fp_line (start 2.25 1.05) (end -2.25 1.05) (layer F.CrtYd) (width 0.05))
(pad 1 smd rect (at -1.5 0) (size 1 1.6) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 1.5 0) (size 1 1.6) (layers F.Cu F.Paste F.Mask))
(model Capacitors_SMD.3dshapes/C_1206.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 0))
)
)

25
hardware/rev1/kicad/proj_footprints.pretty/DO-214AB.kicad_mod
View File

@ -1,25 +0,0 @@
(module DO-214AB (layer F.Cu) (tedit 5825692F)
(descr "Jedec DO-214AB diode package. Designed according to Fairchild SS32 datasheet.")
(tags "DO-214AB diode")
(attr smd)
(fp_text reference REF** (at 0 -4.2) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value DO-214AB (at 0 4.6) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -5.5 -2.6) (end -5.5 2.5) (layer F.SilkS) (width 0.15))
(fp_line (start -5.15 -3.45) (end 5.15 -3.45) (layer F.CrtYd) (width 0.05))
(fp_line (start 5.15 -3.45) (end 5.15 3.45) (layer F.CrtYd) (width 0.05))
(fp_line (start 5.15 3.45) (end -5.15 3.45) (layer F.CrtYd) (width 0.05))
(fp_line (start -5.15 3.45) (end -5.15 -3.45) (layer F.CrtYd) (width 0.05))
(fp_line (start 3.5 3.2) (end -4.8 3.2) (layer F.SilkS) (width 0.15))
(fp_line (start -4.8 -3.2) (end 3.5 -3.2) (layer F.SilkS) (width 0.15))
(pad 2 smd rect (at 3.6 0) (size 2.6 3.2) (layers F.Cu F.Paste F.Mask))
(pad 1 smd rect (at -3.6 0) (size 2.6 3.2) (layers F.Cu F.Paste F.Mask))
(model Diodes_SMD.3dshapes/DO-214AB.wrl
(at (xyz 0 0 0))
(scale (xyz 0.39 0.39 0.39))
(rotate (xyz 0 0 180))
)
)

17
hardware/rev1/kicad/proj_footprints.pretty/DO-214AC.kicad_mod
View File

@ -1,17 +0,0 @@
(module DO-214AC (layer F.Cu) (tedit 5833D139)
(fp_text reference REF** (at -1.5 2.7) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value DO-214AC (at -0.1 0) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -0.9 -1.4) (end -0.9 1.4) (layer F.SilkS) (width 0.15))
(fp_line (start -2.3 -1.4) (end -2.3 -1.1) (layer F.SilkS) (width 0.15))
(fp_line (start 2.3 1.1) (end 2.3 1.4) (layer F.SilkS) (width 0.15))
(fp_line (start 2.3 1.4) (end -2.3 1.4) (layer F.SilkS) (width 0.15))
(fp_line (start -2.3 1.4) (end -2.3 1.1) (layer F.SilkS) (width 0.15))
(fp_line (start -2.3 -1.4) (end 2.3 -1.4) (layer F.SilkS) (width 0.15))
(fp_line (start 2.3 -1.4) (end 2.3 -1.1) (layer F.SilkS) (width 0.15))
(pad 1 smd rect (at -2.2 0) (size 2.1 1.8) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 2.2 0) (size 2.1 1.8) (layers F.Cu F.Paste F.Mask))
)

29
hardware/rev1/kicad/proj_footprints.pretty/DPAK.kicad_mod
View File

@ -1,29 +0,0 @@
(module DPAK (layer F.Cu) (tedit 4FF970FF)
(descr "MOS boitier DPACK G-D-S")
(tags "CMD DPACK")
(attr smd)
(fp_text reference DPAK (at 0 -10.414) (layer F.SilkS)
(effects (font (size 0.29972 0.29972) (thickness 0.0762)))
)
(fp_text value VAL** (at 0 -4.39928) (layer F.SilkS)
(effects (font (size 0.29972 0.29972) (thickness 0.0762)))
)
(fp_line (start 1.34874 1.69926) (end 1.34874 -3.2004) (layer F.SilkS) (width 0.381))
(fp_line (start 1.34874 1.69926) (end 3.2512 1.69926) (layer F.SilkS) (width 0.381))
(fp_line (start 3.2512 1.69926) (end 3.2512 -3.2004) (layer F.SilkS) (width 0.381))
(fp_line (start -3.2512 1.651) (end -3.2512 -3.2004) (layer F.SilkS) (width 0.381))
(fp_line (start -3.2512 1.651) (end -1.34874 1.651) (layer F.SilkS) (width 0.381))
(fp_line (start -1.34874 1.651) (end -1.34874 -3.2004) (layer F.SilkS) (width 0.381))
(fp_line (start -3.44932 -10.09904) (end 3.44932 -10.09904) (layer F.SilkS) (width 0.381))
(fp_line (start 3.44932 -10.09904) (end 3.44932 -3.2004) (layer F.SilkS) (width 0.381))
(fp_line (start 3.44932 -3.2004) (end -3.44932 -3.2004) (layer F.SilkS) (width 0.381))
(fp_line (start -3.44932 -3.2004) (end -3.44932 -10.09904) (layer F.SilkS) (width 0.381))
(pad 1 smd rect (at -2.30124 0) (size 1.651 3.048) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at 0 -6.64972) (size 6.70052 6.70052) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 2.30124 0) (size 1.651 3.048) (layers F.Cu F.Paste F.Mask))
(model smd/dpack_2.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 0))
)
)

23
hardware/rev1/kicad/proj_footprints.pretty/FCI_54601-908WPLF.kicad_mod
View File

@ -1,23 +0,0 @@
(module FCI_54601-908WPLF locked (layer F.Cu) (tedit 58343208)
(fp_text reference J2 (at 14.6 6) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value NET_OUT (at 5.7 0.1) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start 13.4 -1.8) (end 13.4 -5.2) (layer F.SilkS) (width 0.15))
(fp_line (start -2 -1.8) (end -2 -5.2) (layer F.SilkS) (width 0.15))
(fp_line (start -2 10.2) (end -2 1.8) (layer F.SilkS) (width 0.15))
(fp_line (start 13.4 10.2) (end 13.4 1.8) (layer F.SilkS) (width 0.15))
(fp_line (start 13.416 10.2) (end -1.984 10.2) (layer F.SilkS) (width 0.15))
(pad "" np_thru_hole circle (at 0 0) (size 3.75 3.75) (drill 3.25) (layers *.Cu *.Mask F.SilkS))
(pad 2 thru_hole circle (at 8.89 8.89) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
(pad "" np_thru_hole circle (at 11.432 0) (size 3.75 3.75) (drill 3.25) (layers *.Cu *.Mask F.SilkS))
(pad 4 thru_hole circle (at 6.35 8.89) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
(pad 6 thru_hole circle (at 3.81 8.89) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
(pad 8 thru_hole circle (at 1.27 8.89) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
(pad 1 thru_hole circle (at 10.16 6.35) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
(pad 3 thru_hole circle (at 7.62 6.35) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
(pad 5 thru_hole circle (at 5.08 6.35) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
(pad 7 thru_hole circle (at 2.54 6.35) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
)

31
hardware/rev1/kicad/proj_footprints.pretty/H2019FNL.kicad_mod
View File

@ -1,31 +0,0 @@
(module H2019FNL (layer F.Cu) (tedit 582FE01B)
(fp_text reference REF** (at -4.8 6.4 180) (layer F.SilkS)
(effects (font (size 1.2 1.2) (thickness 0.15)))
)
(fp_text value H2019FNL (at 0 0) (layer F.Fab)
(effects (font (size 1.2 1.2) (thickness 0.15)))
)
(fp_circle (center -5.6 3.4) (end -6.1 3.6) (layer F.SilkS) (width 0.15))
(fp_line (start 5 4.6) (end 6.4 4.6) (layer F.SilkS) (width 0.15))
(fp_line (start 6.4 4.6) (end 6.4 -4.6) (layer F.SilkS) (width 0.15))
(fp_line (start 6.4 -4.6) (end 5 -4.6) (layer F.SilkS) (width 0.15))
(fp_line (start -5 -4.6) (end -6.4 -4.6) (layer F.SilkS) (width 0.15))
(fp_line (start -6.4 -4.6) (end -6.4 4.6) (layer F.SilkS) (width 0.15))
(fp_line (start -6.4 4.6) (end -5 4.6) (layer F.SilkS) (width 0.15))
(pad 16 smd rect (at -4.445 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 1 smd rect (at -4.445 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 15 smd rect (at -3.175 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at -3.175 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 14 smd rect (at -1.905 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at -1.905 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 13 smd rect (at -0.635 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 4 smd rect (at -0.635 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 12 smd rect (at 0.635 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 5 smd rect (at 0.635 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 11 smd rect (at 1.905 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 6 smd rect (at 1.905 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 10 smd rect (at 3.175 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 7 smd rect (at 3.175 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 9 smd rect (at 4.445 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 8 smd rect (at 4.445 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
)

9
hardware/rev1/kicad/proj_footprints.pretty/NPTH_3mm_ID.kicad_mod
View File

@ -1,9 +0,0 @@
(module NPTH_3mm_ID (layer F.Cu) (tedit 58345150)
(fp_text reference H4 (at 0 2.9) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value 3mm_Mounting_Hole (at 0 -2.7) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(pad "" np_thru_hole circle (at 0 0) (size 3 3) (drill 3) (layers *.Cu *.Mask))
)

24
hardware/rev1/kicad/proj_footprints.pretty/PhoenixContact_1786417_03.kicad_mod
View File

@ -1,24 +0,0 @@
(module Connectors_Phoenix:PhoenixContact_MC-G_03x5.08mm_Angled (layer F.Cu) (tedit 58F9A094)
(descr PhoenixContact_1786417_03x5.08mm_Angled)
(tags "phoenix_contact connector 01x03_G_5.08mm")
(fp_text reference REF** (at 4.826 -4.064) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value PhoenixContact_1786417_03x5.08mm_Angled (at 5.08 9.5) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -2.62 -3) (end -2.62 16) (layer F.SilkS) (width 0.15))
(fp_line (start -2.62 16) (end 12.78 16) (layer F.SilkS) (width 0.15))
(fp_line (start 12.78 16) (end 12.78 -3) (layer F.SilkS) (width 0.15))
(fp_line (start -2.62 -3) (end 12.78 -3) (layer F.SilkS) (width 0.15))
(fp_line (start -2.62 8) (end 12.78 8) (layer F.SilkS) (width 0.15))
(fp_line (start 0 -2.3) (end 0.3 -2.9) (layer F.SilkS) (width 0.15))
(fp_line (start 0.3 -2.9) (end -0.3 -2.9) (layer F.SilkS) (width 0.15))
(fp_line (start -0.3 -2.9) (end 0 -2.3) (layer F.SilkS) (width 0.15))
(pad 3 thru_hole oval (at 10.16 5.08) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 2 thru_hole oval (at 5.08 5.08) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 1 thru_hole rect (at 0 5.08) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 1 thru_hole rect (at 0 0) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 2 thru_hole oval (at 5.08 0) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 3 thru_hole oval (at 10.16 0) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
)

32
hardware/rev1/kicad/proj_footprints.pretty/Pin_Header_Straight_2x05_Pitch1.27mm.kicad_mod
View File

@ -1,32 +0,0 @@
(module Pin_Header_Straight_2x05_Pitch1.27mm (layer F.Cu) (tedit 58705FA3)
(descr "Through hole pin header, pitch 1.27mm")
(tags "pin header")
(fp_text reference REF** (at -1.8 0 90) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value PH2X05VR1MM27 (at 0 6.9) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -1.1 0.5) (end -1.1 -1.1) (layer F.SilkS) (width 0.15))
(fp_line (start -1.1 -1.1) (end 0.5 -1.1) (layer F.SilkS) (width 0.15))
(fp_line (start 2.1 -0.8) (end 1.3 -0.8) (layer F.SilkS) (width 0.15))
(fp_line (start 2.1 5.85) (end 2.1 -0.8) (layer F.SilkS) (width 0.15))
(fp_line (start 2.1 5.85) (end -0.85 5.85) (layer F.SilkS) (width 0.15))
(fp_line (start -1.1 -1.05) (end -1.1 6.1) (layer F.CrtYd) (width 0.05))
(fp_line (start 2.35 -1.05) (end 2.35 6.1) (layer F.CrtYd) (width 0.05))
(fp_line (start -1.1 -1.05) (end 2.35 -1.05) (layer F.CrtYd) (width 0.05))
(fp_line (start -1.1 6.1) (end 2.35 6.1) (layer F.CrtYd) (width 0.05))
(fp_line (start -0.85 5.85) (end -0.85 1.3) (layer F.SilkS) (width 0.15))
(fp_line (start 0.5 -0.8) (end -0.85 -0.8) (layer F.SilkS) (width 0.15))
(fp_line (start -0.85 -0.8) (end -0.85 0.5) (layer F.SilkS) (width 0.15))
(pad 1 thru_hole rect (at 0 0) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 3 thru_hole circle (at 0 1.27) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 5 thru_hole circle (at 0 2.54) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 7 thru_hole circle (at 0 3.81) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 9 thru_hole circle (at 0 5.08) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 4 thru_hole circle (at 1.27 1.27) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 6 thru_hole circle (at 1.27 2.54) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 8 thru_hole circle (at 1.27 3.81) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 10 thru_hole circle (at 1.27 5.08) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 2 thru_hole circle (at 1.27 0) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
)

29
hardware/rev1/kicad/proj_footprints.pretty/R_1206_ns.kicad_mod
View File

@ -1,29 +0,0 @@
(module Resistors_SMD:R_1206 (layer F.Cu) (tedit 58FF4C8B)
(descr "Resistor SMD 1206, reflow soldering, Vishay (see dcrcw.pdf)")
(tags "resistor 1206")
(attr smd)
(fp_text reference R104 (at 7.184205 1.257236) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value 10M/1206 (at 0 1.95) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text user %R (at 0 0) (layer F.Fab)
(effects (font (size 0.7 0.7) (thickness 0.105)))
)
(fp_line (start -1.6 0.8) (end -1.6 -0.8) (layer F.Fab) (width 0.1))
(fp_line (start 1.6 0.8) (end -1.6 0.8) (layer F.Fab) (width 0.1))
(fp_line (start 1.6 -0.8) (end 1.6 0.8) (layer F.Fab) (width 0.1))
(fp_line (start -1.6 -0.8) (end 1.6 -0.8) (layer F.Fab) (width 0.1))
(fp_line (start -2.15 -1.11) (end 2.15 -1.11) (layer F.CrtYd) (width 0.05))
(fp_line (start -2.15 -1.11) (end -2.15 1.1) (layer F.CrtYd) (width 0.05))
(fp_line (start 2.15 1.1) (end 2.15 -1.11) (layer F.CrtYd) (width 0.05))
(fp_line (start 2.15 1.1) (end -2.15 1.1) (layer F.CrtYd) (width 0.05))
(pad 1 smd rect (at -1.45 0) (size 0.9 1.7) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 1.45 0) (size 0.9 1.7) (layers F.Cu F.Paste F.Mask))
(model ${KISYS3DMOD}/Resistors_SMD.3dshapes/R_1206.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 0))
)
)

18
hardware/rev1/kicad/proj_footprints.pretty/SC-90A.kicad_mod
View File

@ -1,18 +0,0 @@
(module SC-90A (layer F.Cu) (tedit 58079009)
(fp_text reference REF** (at 3.1 0) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value SC-90A (at 0 -2.5) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -0.6 0.4) (end 0.6 0.4) (layer F.SilkS) (width 0.15))
(fp_line (start -0.6 -0.4) (end 0.6 -0.4) (layer F.SilkS) (width 0.15))
(fp_line (start 0.6 -0.4) (end 0 0.3) (layer F.SilkS) (width 0.15))
(fp_line (start 0 0.3) (end -0.6 -0.4) (layer F.SilkS) (width 0.15))
(fp_line (start -0.8 -2) (end -0.8 2) (layer F.SilkS) (width 0.15))
(fp_line (start -0.8 2) (end 0.8 2) (layer F.SilkS) (width 0.15))
(fp_line (start 0.8 2) (end 0.8 -2) (layer F.SilkS) (width 0.15))
(fp_line (start 0.8 -2) (end -0.8 -2) (layer F.SilkS) (width 0.15))
(pad 2 smd rect (at 0 -1.2) (size 0.9 0.9) (layers F.Cu F.Paste F.Mask))
(pad 1 smd rect (at 0 1.2) (size 1.1 0.9) (layers F.Cu F.Paste F.Mask))
)

18
hardware/rev1/kicad/proj_footprints.pretty/SC70-5.kicad_mod
View File

@ -1,18 +0,0 @@
(module SC70-5 (layer F.Cu) (tedit 589D8A3B)
(fp_text reference REF** (at 0.3 0.2) (layer F.SilkS)
(effects (font (size 0.3 0.3) (thickness 0.075)))
)
(fp_text value SC70-5 (at 0 -0.3) (layer F.SilkS)
(effects (font (size 0.3 0.3) (thickness 0.075)))
)
(fp_circle (center -0.7 0.2) (end -0.7 0.3) (layer F.SilkS) (width 0.15))
(fp_line (start -1 -0.6) (end 1 -0.6) (layer F.SilkS) (width 0.15))
(fp_line (start 1 -0.6) (end 1 0.6) (layer F.SilkS) (width 0.15))
(fp_line (start 1 0.6) (end -1 0.6) (layer F.SilkS) (width 0.15))
(fp_line (start -1 0.6) (end -1 -0.6) (layer F.SilkS) (width 0.15))
(pad 1 smd rect (at -0.65 0.95) (size 0.4 0.7) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 0 0.95) (size 0.4 0.7) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at 0.65 0.95) (size 0.4 0.7) (layers F.Cu F.Paste F.Mask))
(pad 4 smd rect (at 0.65 -0.95) (size 0.4 0.7) (layers F.Cu F.Paste F.Mask))
(pad 5 smd rect (at -0.65 -0.95) (size 0.4 0.7) (layers F.Cu F.Paste F.Mask))
)

32
hardware/rev1/kicad/proj_footprints.pretty/SC70-6.kicad_mod
View File

@ -1,32 +0,0 @@
(module SC-70-6 (layer F.Cu) (tedit 54CBD979)
(attr smd)
(fp_text reference REF** (at 0 0) (layer F.SilkS)
(effects (font (size 0.8 0.8) (thickness 0.15)))
)
(fp_text value SC-70-6 (at 0 0) (layer F.Fab)
(effects (font (size 0.8 0.8) (thickness 0.15)))
)
(fp_line (start -0.5 -1.25) (end -0.5 -0.75) (layer F.Fab) (width 0.15))
(fp_line (start -0.5 -0.75) (end -1.5 -0.75) (layer F.Fab) (width 0.15))
(fp_line (start -1.5 -1.25) (end -1.5 1.25) (layer F.Fab) (width 0.15))
(fp_line (start -1.5 1.25) (end 1.5 1.25) (layer F.Fab) (width 0.15))
(fp_line (start 1.5 1.25) (end 1.5 -1.25) (layer F.Fab) (width 0.15))
(fp_line (start 1.5 -1.25) (end -1.5 -1.25) (layer F.Fab) (width 0.15))
(fp_line (start -1.4 -1.1) (end -0.5 -1.1) (layer F.SilkS) (width 0.15))
(fp_line (start -1.75 -1.5) (end 1.75 -1.5) (layer F.CrtYd) (width 0.15))
(fp_line (start 1.75 -1.5) (end 1.75 1.5) (layer F.CrtYd) (width 0.15))
(fp_line (start 1.75 1.5) (end -1.75 1.5) (layer F.CrtYd) (width 0.15))
(fp_line (start -1.75 1.5) (end -1.75 -1.5) (layer F.CrtYd) (width 0.15))
(fp_line (start 0 -1) (end 0 1) (layer F.SilkS) (width 0.35))
(pad 5 smd rect (at 0.95 0 180) (size 0.75 0.4) (layers F.Cu F.Paste F.Mask))
(pad 1 smd rect (at -0.95 -0.65 180) (size 0.75 0.4) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at -0.95 0.65 180) (size 0.75 0.4) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at -0.95 0 180) (size 0.75 0.4) (layers F.Cu F.Paste F.Mask))
(pad 4 smd rect (at 0.95 0.65 180) (size 0.75 0.4) (layers F.Cu F.Paste F.Mask))
(pad 6 smd rect (at 0.95 -0.65 180) (size 0.75 0.4) (layers F.Cu F.Paste F.Mask))
(model smd_trans/sc70-6.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 90))
)
)

48
hardware/rev1/kicad/proj_footprints.pretty/SOIC-16_3.9x9.9mm_Pitch1.27mm.kicad_mod
View File

@ -1,48 +0,0 @@
(module Housings_SOIC:SOIC-16_3.9x9.9mm_Pitch1.27mm (layer F.Cu) (tedit 574D979F)
(descr "16-Lead Plastic Small Outline (SL) - Narrow, 3.90 mm Body [SOIC] (see Microchip Packaging Specification 00000049BS.pdf)")
(tags "SOIC 1.27")
(attr smd)
(fp_text reference REF** (at 0 -6) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value SOIC-16_3.9x9.9mm_Pitch1.27mm (at 0 6) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -0.95 -4.95) (end 1.95 -4.95) (layer F.Fab) (width 0.15))
(fp_line (start 1.95 -4.95) (end 1.95 4.95) (layer F.Fab) (width 0.15))
(fp_line (start 1.95 4.95) (end -1.95 4.95) (layer F.Fab) (width 0.15))
(fp_line (start -1.95 4.95) (end -1.95 -3.95) (layer F.Fab) (width 0.15))
(fp_line (start -1.95 -3.95) (end -0.95 -4.95) (layer F.Fab) (width 0.15))
(fp_line (start -3.7 -5.25) (end -3.7 5.25) (layer F.CrtYd) (width 0.05))
(fp_line (start 3.7 -5.25) (end 3.7 5.25) (layer F.CrtYd) (width 0.05))
(fp_line (start -3.7 -5.25) (end 3.7 -5.25) (layer F.CrtYd) (width 0.05))
(fp_line (start -3.7 5.25) (end 3.7 5.25) (layer F.CrtYd) (width 0.05))
(fp_line (start -2.075 -5.075) (end -2.075 -5.05) (layer F.SilkS) (width 0.15))
(fp_line (start 2.075 -5.075) (end 2.075 -4.97) (layer F.SilkS) (width 0.15))
(fp_line (start 2.075 5.075) (end 2.075 4.97) (layer F.SilkS) (width 0.15))
(fp_line (start -2.075 5.075) (end -2.075 4.97) (layer F.SilkS) (width 0.15))
(fp_line (start -2.075 -5.075) (end 2.075 -5.075) (layer F.SilkS) (width 0.15))
(fp_line (start -2.075 5.075) (end 2.075 5.075) (layer F.SilkS) (width 0.15))
(fp_line (start -2.075 -5.05) (end -3.45 -5.05) (layer F.SilkS) (width 0.15))
(pad 1 smd rect (at -2.7 -4.445) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at -2.7 -3.175) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at -2.7 -1.905) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 4 smd rect (at -2.7 -0.635) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 5 smd rect (at -2.7 0.635) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 6 smd rect (at -2.7 1.905) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 7 smd rect (at -2.7 3.175) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 8 smd rect (at -2.7 4.445) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 9 smd rect (at 2.7 4.445) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 10 smd rect (at 2.7 3.175) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 11 smd rect (at 2.7 1.905) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 12 smd rect (at 2.7 0.635) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 13 smd rect (at 2.7 -0.635) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 14 smd rect (at 2.7 -1.905) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 15 smd rect (at 2.7 -3.175) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(pad 16 smd rect (at 2.7 -4.445) (size 1.5 0.6) (layers F.Cu F.Paste F.Mask))
(model Housings_SOIC.3dshapes/SOIC-16_3.9x9.9mm_Pitch1.27mm.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 0))
)
)

29
hardware/rev1/kicad/proj_footprints.pretty/SOIC-8-N_ns.kicad_mod
View File

@ -1,29 +0,0 @@
(module SMD_Packages:SOIC-8-N (layer F.Cu) (tedit 58FF4DF4)
(descr "Module Narrow CMS SOJ 8 pins large")
(tags "CMS SOJ")
(attr smd)
(fp_text reference U100 (at 3.556 0 90) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value LMP7721 (at 0 1.27) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start 2.54 -2.286) (end 2.54 2.286) (layer F.SilkS) (width 0.15))
(fp_line (start 2.54 2.286) (end -2.54 2.286) (layer F.SilkS) (width 0.15))
(fp_line (start -2.54 0.762) (end -2.032 0.762) (layer F.SilkS) (width 0.15))
(fp_line (start -2.032 0.762) (end -2.032 2.032) (layer F.SilkS) (width 0.15))
(fp_line (start -2.032 2.032) (end -2.54 2.032) (layer F.SilkS) (width 0.15))
(pad 8 smd rect (at -1.905 -3.175) (size 0.508 1.143) (layers F.Cu F.Paste F.Mask))
(pad 7 smd rect (at -0.635 -3.175) (size 0.508 1.143) (layers F.Cu F.Paste F.Mask))
(pad 6 smd rect (at 0.635 -3.175) (size 0.508 1.143) (layers F.Cu F.Paste F.Mask))
(pad 5 smd rect (at 1.905 -3.175) (size 0.508 1.143) (layers F.Cu F.Paste F.Mask))
(pad 4 smd rect (at 1.905 3.175) (size 0.508 1.143) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at 0.635 3.175) (size 0.508 1.143) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at -0.635 3.175) (size 0.508 1.143) (layers F.Cu F.Paste F.Mask))
(pad 1 smd rect (at -1.905 3.175) (size 0.508 1.143) (layers F.Cu F.Paste F.Mask))
(model SMD_Packages.3dshapes/SOIC-8-N.wrl
(at (xyz 0 0 0))
(scale (xyz 0.5 0.38 0.5))
(rotate (xyz 0 0 0))
)
)

23
hardware/rev1/kicad/proj_footprints.pretty/SOIC-8.kicad_mod
View File

@ -1,23 +0,0 @@
(module SOIC-8 (layer F.Cu) (tedit 582FE8D6)
(fp_text reference REF** (at -2.2 4.4 180) (layer F.SilkS)
(effects (font (size 1.2 1.2) (thickness 0.15)))
)
(fp_text value SOIC-8 (at 0 0) (layer F.Fab)
(effects (font (size 1.2 1.2) (thickness 0.15)))
)
(fp_circle (center -1.7 1.3) (end -2.1 1.5) (layer F.SilkS) (width 0.15))
(fp_line (start 2.5 -2) (end 2.5 2) (layer F.SilkS) (width 0.15))
(fp_line (start 2.5 2) (end 2.4 2) (layer F.SilkS) (width 0.15))
(fp_line (start 2.5 -2) (end 2.4 -2) (layer F.SilkS) (width 0.15))
(fp_line (start -2.4 -2) (end -2.5 -2) (layer F.SilkS) (width 0.15))
(fp_line (start -2.5 -2) (end -2.5 2) (layer F.SilkS) (width 0.15))
(fp_line (start -2.5 2) (end -2.4 2) (layer F.SilkS) (width 0.15))
(pad 8 smd rect (at -1.905 -2.76) (size 0.6 1.52) (layers F.Cu F.Paste F.Mask))
(pad 1 smd rect (at -1.905 2.76) (size 0.6 1.52) (layers F.Cu F.Paste F.Mask))
(pad 7 smd rect (at -0.635 -2.76) (size 0.6 1.52) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at -0.635 2.76) (size 0.6 1.52) (layers F.Cu F.Paste F.Mask))
(pad 6 smd rect (at 0.635 -2.76) (size 0.6 1.52) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at 0.635 2.76) (size 0.6 1.52) (layers F.Cu F.Paste F.Mask))
(pad 5 smd rect (at 1.905 -2.76) (size 0.6 1.52) (layers F.Cu F.Paste F.Mask))
(pad 4 smd rect (at 1.905 2.76) (size 0.6 1.52) (layers F.Cu F.Paste F.Mask))
)

33
hardware/rev1/kicad/proj_footprints.pretty/SOT-223.kicad_mod
View File

@ -1,33 +0,0 @@
(module SOT-223 (layer F.Cu) (tedit 5883B228)
(descr "module CMS SOT223 4 pins")
(tags "CMS SOT")
(attr smd)
(fp_text reference REF** (at 0 -4.5) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value SOT-223 (at 0 4.5) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -1.85 -2.3) (end -0.8 -3.35) (layer F.Fab) (width 0.1))
(fp_line (start 1.91 3.41) (end 1.91 2.15) (layer F.SilkS) (width 0.12))
(fp_line (start 1.91 -3.41) (end 1.91 -2.15) (layer F.SilkS) (width 0.12))
(fp_line (start 4.4 -3.6) (end -4.4 -3.6) (layer F.CrtYd) (width 0.05))
(fp_line (start 4.4 3.6) (end 4.4 -3.6) (layer F.CrtYd) (width 0.05))
(fp_line (start -4.4 3.6) (end 4.4 3.6) (layer F.CrtYd) (width 0.05))
(fp_line (start -4.4 -3.6) (end -4.4 3.6) (layer F.CrtYd) (width 0.05))
(fp_line (start -1.85 -2.3) (end -1.85 3.35) (layer F.Fab) (width 0.1))
(fp_line (start -1.85 3.41) (end 1.91 3.41) (layer F.SilkS) (width 0.12))
(fp_line (start -0.8 -3.35) (end 1.85 -3.35) (layer F.Fab) (width 0.1))
(fp_line (start -4.1 -3.41) (end 1.91 -3.41) (layer F.SilkS) (width 0.12))
(fp_line (start -1.85 3.35) (end 1.85 3.35) (layer F.Fab) (width 0.1))
(fp_line (start 1.85 -3.35) (end 1.85 3.35) (layer F.Fab) (width 0.1))
(pad 4 smd rect (at 3.15 0) (size 2 3.8) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at -3.15 0) (size 2 1.5) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at -3.15 2.3) (size 2 1.5) (layers F.Cu F.Paste F.Mask))
(pad 1 smd rect (at -3.15 -2.3) (size 2 1.5) (layers F.Cu F.Paste F.Mask))
(model TO_SOT_Packages_SMD.3dshapes/SOT-223.wrl
(at (xyz 0 0 0))
(scale (xyz 0.4 0.4 0.4))
(rotate (xyz 0 0 90))
)
)

30
hardware/rev1/kicad/proj_footprints.pretty/SOT-23-5.kicad_mod
View File

@ -1,30 +0,0 @@
(module SOT-23-5 (layer F.Cu) (tedit 55360473)
(descr "5-pin SOT23 package")
(tags SOT-23-5)
(attr smd)
(fp_text reference REF** (at -0.05 -2.55) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value SOT-23-5 (at -0.05 2.35) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -1.8 -1.6) (end 1.8 -1.6) (layer F.CrtYd) (width 0.05))
(fp_line (start 1.8 -1.6) (end 1.8 1.6) (layer F.CrtYd) (width 0.05))
(fp_line (start 1.8 1.6) (end -1.8 1.6) (layer F.CrtYd) (width 0.05))
(fp_line (start -1.8 1.6) (end -1.8 -1.6) (layer F.CrtYd) (width 0.05))
(fp_circle (center -0.3 -1.7) (end -0.2 -1.7) (layer F.SilkS) (width 0.15))
(fp_line (start 0.25 -1.45) (end -0.25 -1.45) (layer F.SilkS) (width 0.15))
(fp_line (start 0.25 1.45) (end 0.25 -1.45) (layer F.SilkS) (width 0.15))
(fp_line (start -0.25 1.45) (end 0.25 1.45) (layer F.SilkS) (width 0.15))
(fp_line (start -0.25 -1.45) (end -0.25 1.45) (layer F.SilkS) (width 0.15))
(pad 1 smd rect (at -1.1 -0.95) (size 1.06 0.65) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at -1.1 0) (size 1.06 0.65) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at -1.1 0.95) (size 1.06 0.65) (layers F.Cu F.Paste F.Mask))
(pad 4 smd rect (at 1.1 0.95) (size 1.06 0.65) (layers F.Cu F.Paste F.Mask))
(pad 5 smd rect (at 1.1 -0.95) (size 1.06 0.65) (layers F.Cu F.Paste F.Mask))
(model TO_SOT_Packages_SMD.3dshapes/SOT-23-5.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 0))
)
)

27
hardware/rev1/kicad/proj_footprints.pretty/SOT-23-6.kicad_mod
View File

@ -1,27 +0,0 @@
(module SOT-23-6 (layer F.Cu) (tedit 53DE8DE3)
(descr "6-pin SOT-23 package")
(tags SOT-23-6)
(attr smd)
(fp_text reference REF** (at 0 -2.9) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value SOT-23-6 (at 0 2.9) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_circle (center -0.4 -1.7) (end -0.3 -1.7) (layer F.SilkS) (width 0.15))
(fp_line (start 0.25 -1.45) (end -0.25 -1.45) (layer F.SilkS) (width 0.15))
(fp_line (start 0.25 1.45) (end 0.25 -1.45) (layer F.SilkS) (width 0.15))
(fp_line (start -0.25 1.45) (end 0.25 1.45) (layer F.SilkS) (width 0.15))
(fp_line (start -0.25 -1.45) (end -0.25 1.45) (layer F.SilkS) (width 0.15))
(pad 1 smd rect (at -1.1 -0.95) (size 1.06 0.65) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at -1.1 0) (size 1.06 0.65) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at -1.1 0.95) (size 1.06 0.65) (layers F.Cu F.Paste F.Mask))
(pad 4 smd rect (at 1.1 0.95) (size 1.06 0.65) (layers F.Cu F.Paste F.Mask))
(pad 6 smd rect (at 1.1 -0.95) (size 1.06 0.65) (layers F.Cu F.Paste F.Mask))
(pad 5 smd rect (at 1.1 0) (size 1.06 0.65) (layers F.Cu F.Paste F.Mask))
(model TO_SOT_Packages_SMD.3dshapes/SOT-23-6.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 0))
)
)

16
hardware/rev1/kicad/proj_footprints.pretty/SOT-23.kicad_mod
View File

@ -1,16 +0,0 @@
(module SOT-23 (layer F.Cu) (tedit 582FEB56)
(fp_text reference REF** (at -1.1 2.6) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value SOT-23 (at 0 -0.5) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -0.3 0.7) (end 0.3 0.7) (layer F.SilkS) (width 0.15))
(fp_line (start 1.6 0.7) (end 1.6 -0.7) (layer F.SilkS) (width 0.15))
(fp_line (start 1.6 -0.7) (end 0.6 -0.7) (layer F.SilkS) (width 0.15))
(fp_line (start -0.7 -0.7) (end -1.6 -0.7) (layer F.SilkS) (width 0.15))
(fp_line (start -1.6 -0.7) (end -1.6 0.7) (layer F.SilkS) (width 0.15))
(pad 1 smd rect (at -0.95 1.1) (size 1 1.4) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 0.95 1.1) (size 1 1.4) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at 0 -1.1) (size 1 1.4) (layers F.Cu F.Paste F.Mask))
)

27
hardware/rev1/kicad/proj_footprints.pretty/SPB05A.kicad_mod
View File

@ -1,27 +0,0 @@
(module Pin_Header_Angled_2x17 (layer F.Cu) (tedit 58F9BCFA)
(descr SPB05A)
(fp_text reference REF** (at 0 -5.1) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value SPB05A (at 0 -7.62) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -7.62 -3.048) (end 7.62 -3.048) (layer F.SilkS) (width 0.15))
(fp_line (start -1.524 -1.524) (end -1.524 1.524) (layer F.SilkS) (width 0.15))
(fp_line (start -1.524 1.524) (end 1.524 1.524) (layer F.SilkS) (width 0.15))
(fp_line (start 1.524 1.524) (end 1.524 -1.524) (layer F.SilkS) (width 0.15))
(fp_line (start 1.524 -1.524) (end -1.524 -1.524) (layer F.SilkS) (width 0.15))
(fp_line (start 0 21.59) (end 7.62 21.59) (layer F.SilkS) (width 0.15))
(fp_line (start 7.62 21.59) (end 7.62 -3.81) (layer F.SilkS) (width 0.15))
(fp_line (start 7.62 -3.81) (end -7.62 -3.81) (layer F.SilkS) (width 0.15))
(fp_line (start -7.62 20.32) (end -7.62 21.59) (layer F.SilkS) (width 0.15))
(fp_line (start -7.62 -3.81) (end -7.62 20.32) (layer F.SilkS) (width 0.15))
(fp_line (start -7.62 21.59) (end 0 21.59) (layer F.SilkS) (width 0.15))
(pad 1 thru_hole rect (at 0 0) (size 1.7272 1.7272) (drill 1.016) (layers *.Cu *.Mask F.SilkS))
(pad 2 thru_hole oval (at 0 2.54) (size 1.7272 1.7272) (drill 1.016) (layers *.Cu *.Mask F.SilkS))
(pad 3 thru_hole oval (at 0 5.08) (size 1.7272 1.7272) (drill 1.016) (layers *.Cu *.Mask F.SilkS))
(pad 5 thru_hole oval (at 0 10.16) (size 1.7272 1.7272) (drill 1.016) (layers *.Cu *.Mask F.SilkS))
(pad 6 thru_hole oval (at 0 12.7) (size 1.7272 1.7272) (drill 1.016) (layers *.Cu *.Mask F.SilkS))
(pad 7 thru_hole oval (at 0 15.24) (size 1.7272 1.7272) (drill 1.016) (layers *.Cu *.Mask F.SilkS))
(pad 8 thru_hole oval (at 0 17.78) (size 1.7272 1.7272) (drill 1.016) (layers *.Cu *.Mask F.SilkS))
)

55
hardware/rev1/kicad/proj_footprints.pretty/SW_Tactile_SKHH_Angled_v.kicad_mod
View File

@ -1,55 +0,0 @@
(module Buttons_Switches_ThroughHole:SW_Tactile_SKHH_Angled (layer F.Cu) (tedit 58FF2BB1)
(descr "tactile switch 6mm ALPS SKHH right angle http://www.alps.com/prod/info/E/HTML/Tact/SnapIn/SKHH/SKHHLUA010.html")
(tags "tactile switch 6mm ALPS SKHH right angle")
(fp_text reference S1 (at 0.7 7.4) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)) (justify left bottom))
)
(fp_text value SW_PBTN_2PIN_V (at 2.65 -5.1) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start 4.3 -4.3) (end 7.2 -4.3) (layer F.CrtYd) (width 0.05))
(fp_line (start 7.2 -4.3) (end 7.2 -1.1) (layer F.CrtYd) (width 0.05))
(fp_line (start 7.2 -1.1) (end 6.1 -1.1) (layer F.CrtYd) (width 0.05))
(fp_line (start 6.1 -1.1) (end 6.1 2.9) (layer F.CrtYd) (width 0.05))
(fp_line (start 0.2 -4.3) (end -2.7 -4.3) (layer F.CrtYd) (width 0.05))
(fp_line (start -2.7 -4.3) (end -2.7 -1.1) (layer F.CrtYd) (width 0.05))
(fp_line (start -2.7 -1.1) (end -1.6 -1.1) (layer F.CrtYd) (width 0.05))
(fp_line (start -1.6 -1.1) (end -1.6 2.9) (layer F.CrtYd) (width 0.05))
(fp_line (start 4.3 -2.3) (end 0.2 -2.3) (layer F.CrtYd) (width 0.05))
(fp_line (start -1.6 2.9) (end 0.3 2.9) (layer F.CrtYd) (width 0.05))
(fp_line (start 0.3 2.9) (end 0.3 6.2) (layer F.CrtYd) (width 0.05))
(fp_line (start 0.3 6.2) (end 4.2 6.2) (layer F.CrtYd) (width 0.05))
(fp_line (start 4.2 6.2) (end 4.2 2.9) (layer F.CrtYd) (width 0.05))
(fp_line (start 4.2 2.9) (end 6.1 2.9) (layer F.CrtYd) (width 0.05))
(fp_line (start 4.3 -4.3) (end 4.3 -2.3) (layer F.CrtYd) (width 0.05))
(fp_line (start 0.2 -2.3) (end 0.2 -4.3) (layer F.CrtYd) (width 0.05))
(fp_line (start 3.92 5.85) (end 0.58 5.85) (layer F.Fab) (width 0.1))
(fp_line (start -1.25 2.55) (end -1.25 -4) (layer F.Fab) (width 0.1))
(fp_line (start -1.25 -4) (end -0.85 -4) (layer F.Fab) (width 0.1))
(fp_line (start 5.35 -4) (end 5.75 -4) (layer F.Fab) (width 0.1))
(fp_line (start 5.75 -4) (end 5.75 2.55) (layer F.Fab) (width 0.1))
(fp_line (start -0.85 -2) (end 5.35 -2) (layer F.Fab) (width 0.1))
(fp_line (start -0.85 -2) (end -0.85 -4) (layer F.Fab) (width 0.1))
(fp_line (start 5.35 -2) (end 5.35 -4) (layer F.Fab) (width 0.1))
(fp_line (start -1.25 2.55) (end 0.58 2.55) (layer F.Fab) (width 0.1))
(fp_line (start 0.58 2.55) (end 3.92 2.55) (layer F.Fab) (width 0.1))
(fp_line (start 3.92 2.55) (end 5.75 2.55) (layer F.Fab) (width 0.1))
(fp_line (start 3.92 2.55) (end 3.92 5.85) (layer F.Fab) (width 0.1))
(fp_line (start 0.58 2.55) (end 0.58 5.85) (layer F.Fab) (width 0.1))
(fp_line (start -1.45 -1) (end -1.45 2.55) (layer F.SilkS) (width 0.12))
(fp_line (start -1.25 2.75) (end 5.75 2.75) (layer F.SilkS) (width 0.12))
(fp_line (start 5.95 2.55) (end 5.95 -1) (layer F.SilkS) (width 0.12))
(fp_line (start 4.25 -2.2) (end 0.25 -2.2) (layer F.SilkS) (width 0.12))
(fp_circle (center 4.5 0) (end 4.9445 0) (layer F.Mask) (width 0))
(fp_circle (center 0 0) (end 0.4445 0) (layer F.Mask) (width 0))
(fp_circle (center -1.25 -2.5) (end -0.615 -2.5) (layer F.Mask) (width 0))
(fp_circle (center 5.75 -2.5) (end 6.385 -2.5) (layer F.Mask) (width 0))
(fp_circle (center -1.25 -2.5) (end -0.107 -2.5) (layer B.Mask) (width 0))
(fp_circle (center 4.5 0) (end 5.389 0) (layer B.Mask) (width 0))
(fp_circle (center 0 0) (end 0.889 0) (layer B.Mask) (width 0))
(fp_circle (center 5.75 -2.5) (end 6.893 -2.5) (layer B.Mask) (width 0))
(pad 3 thru_hole circle (at -1.25 -2.5) (size 2.2 2.2) (drill 1.3) (layers *.Cu *.Mask))
(pad 4 thru_hole circle (at 5.75 -2.5) (size 2.2 2.2) (drill 1.3) (layers *.Cu *.Mask))
(pad 1 thru_hole circle (at 0 0) (size 1.7 1.7) (drill 1) (layers *.Cu *.Mask))
(pad 2 thru_hole circle (at 4.5 0) (size 1.7 1.7) (drill 1) (layers *.Cu *.Mask))
)

23
hardware/rev1/kicad/proj_footprints.pretty/TDK_B66206X.kicad_mod
View File

@ -1,23 +0,0 @@
(module Connectors_Phoenix:PhoenixContact_MC-G_03x5.08mm_Angled (layer F.Cu) (tedit 58F9AB42)
(descr TDK_B66208X)
(fp_text reference REF** (at 7.62 -5.08) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value TDK_B66206X (at 7.62 5.08) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -4.38 -2.92) (end -4.38 13.08) (layer F.SilkS) (width 0.15))
(fp_line (start -4.38 13.08) (end 19.62 13.08) (layer F.SilkS) (width 0.15))
(fp_line (start 19.62 13.08) (end 19.62 -2.92) (layer F.SilkS) (width 0.15))
(fp_line (start -4.38 -2.92) (end 19.62 -2.92) (layer F.SilkS) (width 0.15))
(pad 5 thru_hole oval (at 15.24 10.16) (size 2.5 3.6) (drill 1.3) (layers *.Cu *.Mask))
(pad 4 thru_hole oval (at 11.43 10.16) (size 2.5 3.6) (drill 1.3) (layers *.Cu *.Mask))
(pad 6 thru_hole oval (at 15.24 0) (size 2.5 3.6) (drill 1.3) (layers *.Cu *.Mask))
(pad 7 thru_hole oval (at 11.43 0) (size 2.5 3.6) (drill 1.3) (layers *.Cu *.Mask))
(pad 3 thru_hole oval (at 7.62 10.16) (size 2.5 3.6) (drill 1.3) (layers *.Cu *.Mask))
(pad 2 thru_hole oval (at 3.81 10.16) (size 2.5 3.6) (drill 1.3) (layers *.Cu *.Mask))
(pad 1 thru_hole rect (at 0 10.16) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 10 thru_hole oval (at 0 0) (size 2.5 3.6) (drill 1.3) (layers *.Cu *.Mask))
(pad 9 thru_hole oval (at 3.81 0) (size 2.5 3.6) (drill 1.3) (layers *.Cu *.Mask))
(pad 8 thru_hole oval (at 7.62 0) (size 2.5 3.6) (drill 1.3) (layers *.Cu *.Mask))
)

23
hardware/rev1/kicad/proj_footprints.pretty/TDK_B66208X.kicad_mod
View File

@ -1,23 +0,0 @@
(module Connectors_Phoenix:PhoenixContact_MC-G_03x5.08mm_Angled (layer F.Cu) (tedit 58F9A706)
(descr TDK_B66208X)
(fp_text reference REF** (at 10.16 -5.588) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value TDK_B66208X (at 10.16 9.398) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -4.84 -3.65) (end -4.84 16.35) (layer F.SilkS) (width 0.15))
(fp_line (start -4.84 16.35) (end 25.16 16.35) (layer F.SilkS) (width 0.15))
(fp_line (start 25.16 16.35) (end 25.16 -3.65) (layer F.SilkS) (width 0.15))
(fp_line (start -4.84 -3.65) (end 25.16 -3.65) (layer F.SilkS) (width 0.15))
(pad 5 thru_hole oval (at 20.32 12.7) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 4 thru_hole oval (at 15.24 12.7) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 6 thru_hole oval (at 20.32 0) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 7 thru_hole oval (at 15.24 0) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 3 thru_hole oval (at 10.16 12.7) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 2 thru_hole oval (at 5.08 12.7) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 1 thru_hole rect (at 0 12.7) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 10 thru_hole oval (at 0 0) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 9 thru_hole oval (at 5.08 0) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 8 thru_hole oval (at 10.16 0) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
)

20
hardware/rev1/kicad/proj_footprints.pretty/TE_FSM5J.kicad_mod
View File

@ -1,20 +0,0 @@
(module Connectors:IDC_Header_Straight_10pins (layer F.Cu) (tedit 58B8E332)
(descr "10 pins through hole IDC header")
(tags "IDC header socket VASCH")
(fp_text reference REF** (at 0.3175 -5.3975) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value FSM5J (at 0.254 5.2705) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -3.6195 -4.0005) (end 4.699 -4.0005) (layer F.SilkS) (width 0.15))
(fp_line (start 4.699 -4.0005) (end 4.699 4.0005) (layer F.SilkS) (width 0.15))
(fp_line (start 4.699 4.0005) (end -3.429 4.0005) (layer F.SilkS) (width 0.15))
(fp_line (start -3.429 4.0005) (end -3.6195 4.0005) (layer F.SilkS) (width 0.15))
(fp_line (start -3.6195 4.0005) (end -3.6195 -4.0005) (layer F.SilkS) (width 0.15))
(pad 1 thru_hole oval (at -2.25 -3.25) (size 1.7272 1.7272) (drill 1.016) (layers *.Cu *.Mask))
(pad 3 thru_hole oval (at 2.25 -3.25) (size 1.7272 1.7272) (drill 1.016) (layers *.Cu *.Mask))
(pad 2 thru_hole oval (at -2.25 3.25) (size 1.7272 1.7272) (drill 1.016) (layers *.Cu *.Mask))
(pad 5 thru_hole oval (at 4.09 0) (size 1.7272 1.7272) (drill 1.016) (layers *.Cu *.Mask))
(pad 4 thru_hole oval (at 2.25 3.25) (size 1.7272 1.7272) (drill 1.016) (layers *.Cu *.Mask))
)

830
hardware/rev1/kicad/proj_footprints.pretty/TQFP-128.kicad_mod
View File

@ -1,830 +0,0 @@
(module QFP40P1600X1600X120-128N (layer F.Cu) (tedit 0)
(solder_mask_margin 0.1)
(attr smd)
(fp_text reference QFP40P1600X1600X120-128N (at -0.4826 -10.5918) (layer F.SilkS)
(effects (font (size 1.64 1.64) (thickness 0.05)))
)
(fp_text value VAL** (at -0.8636 10.1346) (layer F.SilkS)
(effects (font (size 1.64 1.64) (thickness 0.05)))
)
(fp_line (start -6.6548 -7.0104) (end -7.0104 -7.0104) (layer F.SilkS) (width 0.1524))
(fp_line (start 7.0104 -6.6548) (end 7.0104 -7.0104) (layer F.SilkS) (width 0.1524))
(fp_line (start 6.6548 7.0104) (end 7.0104 7.0104) (layer F.SilkS) (width 0.1524))
(fp_line (start -6.5786 -6.1468) (end -6.1468 -6.5786) (layer F.SilkS) (width 0.1524))
(fp_line (start -7.0104 7.0104) (end -6.6548 7.0104) (layer F.SilkS) (width 0.1524))
(fp_line (start 7.0104 7.0104) (end 7.0104 6.6548) (layer F.SilkS) (width 0.1524))
(fp_line (start 7.0104 -7.0104) (end 6.6548 -7.0104) (layer F.SilkS) (width 0.1524))
(fp_line (start -7.0104 -7.0104) (end -7.0104 -6.6548) (layer F.SilkS) (width 0.1524))
(fp_line (start -7.0104 6.6548) (end -7.0104 7.0104) (layer F.SilkS) (width 0.1524))
(fp_line (start -8.89 -2.794) (end -8.89 -2.413) (layer F.SilkS) (width 0.1524))
(fp_line (start -8.89 -2.413) (end -8.636 -2.413) (layer F.SilkS) (width 0.1524))
(fp_line (start -8.636 -2.413) (end -8.636 -2.794) (layer F.SilkS) (width 0.1524))
(fp_line (start -8.89 1.2192) (end -8.89 1.6002) (layer F.SilkS) (width 0.1524))
(fp_line (start -8.89 1.6002) (end -8.636 1.6002) (layer F.SilkS) (width 0.1524))
(fp_line (start -8.636 1.6002) (end -8.636 1.2192) (layer F.SilkS) (width 0.1524))
(fp_line (start -8.89 5.207) (end -8.89 5.588) (layer F.SilkS) (width 0.1524))
(fp_line (start -8.89 5.588) (end -8.636 5.588) (layer F.SilkS) (width 0.1524))
(fp_line (start -8.636 5.588) (end -8.636 5.207) (layer F.SilkS) (width 0.1524))
(fp_line (start -3.5814 8.636) (end -3.5814 8.89) (layer F.SilkS) (width 0.1524))
(fp_line (start -3.5814 8.89) (end -3.2004 8.89) (layer F.SilkS) (width 0.1524))
(fp_line (start -3.2004 8.89) (end -3.2004 8.636) (layer F.SilkS) (width 0.1524))
(fp_line (start 0.4064 8.636) (end 0.4064 8.89) (layer F.SilkS) (width 0.1524))
(fp_line (start 0.4064 8.89) (end 0.7874 8.89) (layer F.SilkS) (width 0.1524))
(fp_line (start 0.7874 8.89) (end 0.7874 8.636) (layer F.SilkS) (width 0.1524))
(fp_line (start 4.4196 8.636) (end 4.4196 8.89) (layer F.SilkS) (width 0.1524))
(fp_line (start 4.4196 8.89) (end 4.8006 8.89) (layer F.SilkS) (width 0.1524))
(fp_line (start 4.8006 8.89) (end 4.8006 8.636) (layer F.SilkS) (width 0.1524))
(fp_line (start 8.89 4.0132) (end 8.89 4.3942) (layer F.SilkS) (width 0.1524))
(fp_line (start 8.89 4.3942) (end 8.636 4.3942) (layer F.SilkS) (width 0.1524))
(fp_line (start 8.636 4.3942) (end 8.636 4.0132) (layer F.SilkS) (width 0.1524))
(fp_line (start 8.89 0) (end 8.89 0.381) (layer F.SilkS) (width 0.1524))
(fp_line (start 8.89 0.381) (end 8.636 0.381) (layer F.SilkS) (width 0.1524))
(fp_line (start 8.636 0.381) (end 8.636 0) (layer F.SilkS) (width 0.1524))
(fp_line (start 8.89 -3.9878) (end 8.89 -3.6068) (layer F.SilkS) (width 0.1524))
(fp_line (start 8.89 -3.6068) (end 8.636 -3.6068) (layer F.SilkS) (width 0.1524))
(fp_line (start 8.636 -3.6068) (end 8.636 -3.9878) (layer F.SilkS) (width 0.1524))
(fp_line (start 4.8006 -8.636) (end 4.8006 -8.89) (layer F.SilkS) (width 0.1524))
(fp_line (start 4.8006 -8.89) (end 5.1816 -8.89) (layer F.SilkS) (width 0.1524))
(fp_line (start 5.1816 -8.89) (end 5.1816 -8.636) (layer F.SilkS) (width 0.1524))
(fp_line (start 0.8128 -8.636) (end 0.8128 -8.89) (layer F.SilkS) (width 0.1524))
(fp_line (start 0.8128 -8.89) (end 1.1938 -8.89) (layer F.SilkS) (width 0.1524))
(fp_line (start 1.1938 -8.89) (end 1.1938 -8.636) (layer F.SilkS) (width 0.1524))
(fp_line (start -3.2004 -8.636) (end -3.2004 -8.89) (layer F.SilkS) (width 0.1524))
(fp_line (start -3.2004 -8.89) (end -2.8194 -8.89) (layer F.SilkS) (width 0.1524))
(fp_line (start -2.8194 -8.89) (end -2.8194 -8.636) (layer F.SilkS) (width 0.1524))
(fp_line (start 6.096 -7.0104) (end 6.3246 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 6.3246 -7.0104) (end 6.3246 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 6.3246 -8.0264) (end 6.096 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 6.096 -8.0264) (end 6.096 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.6896 -7.0104) (end 5.9182 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.9182 -7.0104) (end 5.9182 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.9182 -8.0264) (end 5.6896 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.6896 -8.0264) (end 5.6896 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.2832 -7.0104) (end 5.5118 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.5118 -7.0104) (end 5.5118 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.5118 -8.0264) (end 5.2832 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.2832 -8.0264) (end 5.2832 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.8768 -7.0104) (end 5.1054 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.1054 -7.0104) (end 5.1054 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.1054 -8.0264) (end 4.8768 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.8768 -8.0264) (end 4.8768 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.4958 -7.0104) (end 4.7244 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.7244 -7.0104) (end 4.7244 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.7244 -8.0264) (end 4.4958 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.4958 -8.0264) (end 4.4958 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.0894 -7.0104) (end 4.318 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.318 -7.0104) (end 4.318 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.318 -8.0264) (end 4.0894 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.0894 -8.0264) (end 4.0894 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.683 -7.0104) (end 3.9116 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.9116 -7.0104) (end 3.9116 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.9116 -8.0264) (end 3.683 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.683 -8.0264) (end 3.683 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.2766 -7.0104) (end 3.5052 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.5052 -7.0104) (end 3.5052 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.5052 -8.0264) (end 3.2766 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.2766 -8.0264) (end 3.2766 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.8956 -7.0104) (end 3.1242 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.1242 -7.0104) (end 3.1242 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.1242 -8.0264) (end 2.8956 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.8956 -8.0264) (end 2.8956 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.4892 -7.0104) (end 2.7178 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.7178 -7.0104) (end 2.7178 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.7178 -8.0264) (end 2.4892 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.4892 -8.0264) (end 2.4892 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.0828 -7.0104) (end 2.3114 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.3114 -7.0104) (end 2.3114 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.3114 -8.0264) (end 2.0828 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.0828 -8.0264) (end 2.0828 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.6764 -7.0104) (end 1.905 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.905 -7.0104) (end 1.905 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.905 -8.0264) (end 1.6764 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.6764 -8.0264) (end 1.6764 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.2954 -7.0104) (end 1.524 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.524 -7.0104) (end 1.524 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.524 -8.0264) (end 1.2954 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.2954 -8.0264) (end 1.2954 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.889 -7.0104) (end 1.1176 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.1176 -7.0104) (end 1.1176 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.1176 -8.0264) (end 0.889 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.889 -8.0264) (end 0.889 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.4826 -7.0104) (end 0.7112 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.7112 -7.0104) (end 0.7112 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.7112 -8.0264) (end 0.4826 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.4826 -8.0264) (end 0.4826 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.0762 -7.0104) (end 0.3048 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.3048 -7.0104) (end 0.3048 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.3048 -8.0264) (end 0.0762 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.0762 -8.0264) (end 0.0762 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.3048 -7.0104) (end -0.0762 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.0762 -7.0104) (end -0.0762 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.0762 -8.0264) (end -0.3048 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.3048 -8.0264) (end -0.3048 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.7112 -7.0104) (end -0.4826 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.4826 -7.0104) (end -0.4826 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.4826 -8.0264) (end -0.7112 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.7112 -8.0264) (end -0.7112 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.1176 -7.0104) (end -0.889 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.889 -7.0104) (end -0.889 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.889 -8.0264) (end -1.1176 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.1176 -8.0264) (end -1.1176 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.524 -7.0104) (end -1.2954 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.2954 -7.0104) (end -1.2954 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.2954 -8.0264) (end -1.524 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.524 -8.0264) (end -1.524 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.905 -7.0104) (end -1.6764 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.6764 -7.0104) (end -1.6764 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.6764 -8.0264) (end -1.905 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.905 -8.0264) (end -1.905 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.3114 -7.0104) (end -2.0828 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.0828 -7.0104) (end -2.0828 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.0828 -8.0264) (end -2.3114 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.3114 -8.0264) (end -2.3114 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.7178 -7.0104) (end -2.4892 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.4892 -7.0104) (end -2.4892 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.4892 -8.0264) (end -2.7178 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.7178 -8.0264) (end -2.7178 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.1242 -7.0104) (end -2.8956 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.8956 -7.0104) (end -2.8956 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.8956 -8.0264) (end -3.1242 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.1242 -8.0264) (end -3.1242 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.5052 -7.0104) (end -3.2766 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.2766 -7.0104) (end -3.2766 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.2766 -8.0264) (end -3.5052 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.5052 -8.0264) (end -3.5052 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.9116 -7.0104) (end -3.683 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.683 -7.0104) (end -3.683 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.683 -8.0264) (end -3.9116 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.9116 -8.0264) (end -3.9116 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.318 -7.0104) (end -4.0894 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.0894 -7.0104) (end -4.0894 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.0894 -8.0264) (end -4.318 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.318 -8.0264) (end -4.318 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.7244 -7.0104) (end -4.4958 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.4958 -7.0104) (end -4.4958 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.4958 -8.0264) (end -4.7244 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.7244 -8.0264) (end -4.7244 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.1054 -7.0104) (end -4.8768 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.8768 -7.0104) (end -4.8768 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.8768 -8.0264) (end -5.1054 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.1054 -8.0264) (end -5.1054 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.5118 -7.0104) (end -5.2832 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.2832 -7.0104) (end -5.2832 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.2832 -8.0264) (end -5.5118 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.5118 -8.0264) (end -5.5118 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.9182 -7.0104) (end -5.7404 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.7404 -7.0104) (end -5.6896 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.6896 -7.0104) (end -5.6896 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.6896 -8.0264) (end -5.9182 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.9182 -8.0264) (end -5.9182 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -6.3246 -7.0104) (end -6.096 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -6.096 -7.0104) (end -6.096 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -6.096 -8.0264) (end -6.3246 -8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -6.3246 -8.0264) (end -6.3246 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -6.096) (end -7.0104 -6.3246) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -6.3246) (end -8.0264 -6.3246) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -6.3246) (end -8.0264 -6.096) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -6.096) (end -7.0104 -6.096) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -5.6896) (end -7.0104 -5.7404) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -5.7404) (end -7.0104 -5.9182) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -5.9182) (end -8.0264 -5.9182) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -5.9182) (end -8.0264 -5.6896) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -5.6896) (end -7.0104 -5.6896) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -5.2832) (end -7.0104 -5.5118) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -5.5118) (end -8.0264 -5.5118) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -5.5118) (end -8.0264 -5.2832) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -5.2832) (end -7.0104 -5.2832) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -4.8768) (end -7.0104 -5.1054) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -5.1054) (end -8.0264 -5.1054) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -5.1054) (end -8.0264 -4.8768) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -4.8768) (end -7.0104 -4.8768) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -4.4958) (end -7.0104 -4.7244) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -4.7244) (end -8.0264 -4.7244) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -4.7244) (end -8.0264 -4.4958) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -4.4958) (end -7.0104 -4.4958) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -4.0894) (end -7.0104 -4.318) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -4.318) (end -8.0264 -4.318) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -4.318) (end -8.0264 -4.0894) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -4.0894) (end -7.0104 -4.0894) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -3.683) (end -7.0104 -3.9116) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -3.9116) (end -8.0264 -3.9116) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -3.9116) (end -8.0264 -3.683) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -3.683) (end -7.0104 -3.683) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -3.2766) (end -7.0104 -3.5052) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -3.5052) (end -8.0264 -3.5052) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -3.5052) (end -8.0264 -3.2766) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -3.2766) (end -7.0104 -3.2766) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -2.8956) (end -7.0104 -3.1242) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -3.1242) (end -8.0264 -3.1242) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -3.1242) (end -8.0264 -2.8956) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -2.8956) (end -7.0104 -2.8956) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -2.4892) (end -7.0104 -2.7178) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -2.7178) (end -8.0264 -2.7178) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -2.7178) (end -8.0264 -2.4892) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -2.4892) (end -7.0104 -2.4892) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -2.0828) (end -7.0104 -2.3114) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -2.3114) (end -8.0264 -2.3114) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -2.3114) (end -8.0264 -2.0828) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -2.0828) (end -7.0104 -2.0828) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -1.6764) (end -7.0104 -1.905) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -1.905) (end -8.0264 -1.905) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -1.905) (end -8.0264 -1.6764) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -1.6764) (end -7.0104 -1.6764) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -1.2954) (end -7.0104 -1.524) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -1.524) (end -8.0264 -1.524) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -1.524) (end -8.0264 -1.2954) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -1.2954) (end -7.0104 -1.2954) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -0.889) (end -7.0104 -1.1176) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -1.1176) (end -8.0264 -1.1176) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -1.1176) (end -8.0264 -0.889) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -0.889) (end -7.0104 -0.889) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -0.4826) (end -7.0104 -0.7112) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -0.7112) (end -8.0264 -0.7112) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -0.7112) (end -8.0264 -0.4826) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -0.4826) (end -7.0104 -0.4826) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -0.0762) (end -7.0104 -0.3048) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -0.3048) (end -8.0264 -0.3048) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -0.3048) (end -8.0264 -0.0762) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 -0.0762) (end -7.0104 -0.0762) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 0.3048) (end -7.0104 0.0762) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 0.0762) (end -8.0264 0.0762) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 0.0762) (end -8.0264 0.3048) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 0.3048) (end -7.0104 0.3048) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 0.7112) (end -7.0104 0.4826) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 0.4826) (end -8.0264 0.4826) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 0.4826) (end -8.0264 0.7112) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 0.7112) (end -7.0104 0.7112) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 1.1176) (end -7.0104 0.889) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 0.889) (end -8.0264 0.889) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 0.889) (end -8.0264 1.1176) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 1.1176) (end -7.0104 1.1176) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 1.524) (end -7.0104 1.2954) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 1.2954) (end -8.0264 1.2954) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 1.2954) (end -8.0264 1.524) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 1.524) (end -7.0104 1.524) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 1.905) (end -7.0104 1.6764) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 1.6764) (end -8.0264 1.6764) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 1.6764) (end -8.0264 1.905) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 1.905) (end -7.0104 1.905) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 2.3114) (end -7.0104 2.0828) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 2.0828) (end -8.0264 2.0828) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 2.0828) (end -8.0264 2.3114) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 2.3114) (end -7.0104 2.3114) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 2.7178) (end -7.0104 2.4892) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 2.4892) (end -8.0264 2.4892) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 2.4892) (end -8.0264 2.7178) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 2.7178) (end -7.0104 2.7178) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 3.1242) (end -7.0104 2.8956) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 2.8956) (end -8.0264 2.8956) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 2.8956) (end -8.0264 3.1242) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 3.1242) (end -7.0104 3.1242) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 3.5052) (end -7.0104 3.2766) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 3.2766) (end -8.0264 3.2766) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 3.2766) (end -8.0264 3.5052) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 3.5052) (end -7.0104 3.5052) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 3.9116) (end -7.0104 3.683) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 3.683) (end -8.0264 3.683) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 3.683) (end -8.0264 3.9116) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 3.9116) (end -7.0104 3.9116) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 4.318) (end -7.0104 4.0894) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 4.0894) (end -8.0264 4.0894) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 4.0894) (end -8.0264 4.318) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 4.318) (end -7.0104 4.318) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 4.7244) (end -7.0104 4.4958) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 4.4958) (end -8.0264 4.4958) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 4.4958) (end -8.0264 4.7244) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 4.7244) (end -7.0104 4.7244) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 5.1054) (end -7.0104 4.8768) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 4.8768) (end -8.0264 4.8768) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 4.8768) (end -8.0264 5.1054) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 5.1054) (end -7.0104 5.1054) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 5.5118) (end -7.0104 5.2832) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 5.2832) (end -8.0264 5.2832) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 5.2832) (end -8.0264 5.5118) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 5.5118) (end -7.0104 5.5118) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 5.9182) (end -7.0104 5.6896) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 5.6896) (end -8.0264 5.6896) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 5.6896) (end -8.0264 5.9182) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 5.9182) (end -7.0104 5.9182) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 6.3246) (end -7.0104 6.096) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 6.096) (end -8.0264 6.096) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 6.096) (end -8.0264 6.3246) (layer Dwgs.User) (width 0.1524))
(fp_line (start -8.0264 6.3246) (end -7.0104 6.3246) (layer Dwgs.User) (width 0.1524))
(fp_line (start -6.096 7.0104) (end -6.3246 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -6.3246 7.0104) (end -6.3246 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -6.3246 8.0264) (end -6.096 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -6.096 8.0264) (end -6.096 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.6896 7.0104) (end -5.9182 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.9182 7.0104) (end -5.9182 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.9182 8.0264) (end -5.6896 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.6896 8.0264) (end -5.6896 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.2832 7.0104) (end -5.5118 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.5118 7.0104) (end -5.5118 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.5118 8.0264) (end -5.2832 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.2832 8.0264) (end -5.2832 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.8768 7.0104) (end -5.1054 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.1054 7.0104) (end -5.1054 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -5.1054 8.0264) (end -4.8768 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.8768 8.0264) (end -4.8768 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.4958 7.0104) (end -4.7244 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.7244 7.0104) (end -4.7244 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.7244 8.0264) (end -4.4958 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.4958 8.0264) (end -4.4958 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.0894 7.0104) (end -4.318 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.318 7.0104) (end -4.318 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.318 8.0264) (end -4.0894 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -4.0894 8.0264) (end -4.0894 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.683 7.0104) (end -3.9116 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.9116 7.0104) (end -3.9116 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.9116 8.0264) (end -3.683 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.683 8.0264) (end -3.683 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.2766 7.0104) (end -3.5052 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.5052 7.0104) (end -3.5052 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.5052 8.0264) (end -3.2766 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.2766 8.0264) (end -3.2766 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.8956 7.0104) (end -3.1242 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.1242 7.0104) (end -3.1242 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -3.1242 8.0264) (end -2.8956 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.8956 8.0264) (end -2.8956 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.4892 7.0104) (end -2.7178 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.7178 7.0104) (end -2.7178 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.7178 8.0264) (end -2.4892 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.4892 8.0264) (end -2.4892 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.0828 7.0104) (end -2.3114 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.3114 7.0104) (end -2.3114 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.3114 8.0264) (end -2.0828 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -2.0828 8.0264) (end -2.0828 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.6764 7.0104) (end -1.905 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.905 7.0104) (end -1.905 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.905 8.0264) (end -1.6764 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.6764 8.0264) (end -1.6764 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.2954 7.0104) (end -1.524 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.524 7.0104) (end -1.524 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.524 8.0264) (end -1.2954 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.2954 8.0264) (end -1.2954 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.889 7.0104) (end -1.1176 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.1176 7.0104) (end -1.1176 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -1.1176 8.0264) (end -0.889 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.889 8.0264) (end -0.889 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.4826 7.0104) (end -0.7112 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.7112 7.0104) (end -0.7112 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.7112 8.0264) (end -0.4826 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.4826 8.0264) (end -0.4826 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.0762 7.0104) (end -0.3048 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.3048 7.0104) (end -0.3048 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.3048 8.0264) (end -0.0762 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start -0.0762 8.0264) (end -0.0762 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.3048 7.0104) (end 0.0762 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.0762 7.0104) (end 0.0762 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.0762 8.0264) (end 0.3048 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.3048 8.0264) (end 0.3048 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.7112 7.0104) (end 0.4826 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.4826 7.0104) (end 0.4826 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.4826 8.0264) (end 0.7112 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.7112 8.0264) (end 0.7112 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.1176 7.0104) (end 0.889 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.889 7.0104) (end 0.889 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 0.889 8.0264) (end 1.1176 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.1176 8.0264) (end 1.1176 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.524 7.0104) (end 1.2954 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.2954 7.0104) (end 1.2954 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.2954 8.0264) (end 1.524 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.524 8.0264) (end 1.524 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.905 7.0104) (end 1.6764 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.6764 7.0104) (end 1.6764 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.6764 8.0264) (end 1.905 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 1.905 8.0264) (end 1.905 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.3114 7.0104) (end 2.0828 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.0828 7.0104) (end 2.0828 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.0828 8.0264) (end 2.3114 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.3114 8.0264) (end 2.3114 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.7178 7.0104) (end 2.4892 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.4892 7.0104) (end 2.4892 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.4892 8.0264) (end 2.7178 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.7178 8.0264) (end 2.7178 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.1242 7.0104) (end 2.8956 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.8956 7.0104) (end 2.8956 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 2.8956 8.0264) (end 3.1242 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.1242 8.0264) (end 3.1242 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.5052 7.0104) (end 3.2766 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.2766 7.0104) (end 3.2766 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.2766 8.0264) (end 3.5052 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.5052 8.0264) (end 3.5052 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.9116 7.0104) (end 3.683 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.683 7.0104) (end 3.683 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.683 8.0264) (end 3.9116 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 3.9116 8.0264) (end 3.9116 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.318 7.0104) (end 4.0894 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.0894 7.0104) (end 4.0894 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.0894 8.0264) (end 4.318 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.318 8.0264) (end 4.318 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.7244 7.0104) (end 4.4958 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.4958 7.0104) (end 4.4958 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.4958 8.0264) (end 4.7244 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.7244 8.0264) (end 4.7244 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.1054 7.0104) (end 4.8768 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.8768 7.0104) (end 4.8768 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 4.8768 8.0264) (end 5.1054 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.1054 8.0264) (end 5.1054 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.5118 7.0104) (end 5.2832 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.2832 7.0104) (end 5.2832 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.2832 8.0264) (end 5.5118 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.5118 8.0264) (end 5.5118 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.9182 7.0104) (end 5.6896 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.6896 7.0104) (end 5.6896 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.6896 8.0264) (end 5.9182 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 5.9182 8.0264) (end 5.9182 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 6.3246 7.0104) (end 6.096 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 6.096 7.0104) (end 6.096 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 6.096 8.0264) (end 6.3246 8.0264) (layer Dwgs.User) (width 0.1524))
(fp_line (start 6.3246 8.0264) (end 6.3246 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 6.096) (end 7.0104 6.3246) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 6.3246) (end 8.0264 6.3246) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 6.3246) (end 8.0264 6.096) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 6.096) (end 7.0104 6.096) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 5.6896) (end 7.0104 5.9182) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 5.9182) (end 8.0264 5.9182) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 5.9182) (end 8.0264 5.6896) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 5.6896) (end 7.0104 5.6896) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 5.2832) (end 7.0104 5.5118) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 5.5118) (end 8.0264 5.5118) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 5.5118) (end 8.0264 5.2832) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 5.2832) (end 7.0104 5.2832) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 4.8768) (end 7.0104 5.1054) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 5.1054) (end 8.0264 5.1054) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 5.1054) (end 8.0264 4.8768) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 4.8768) (end 7.0104 4.8768) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 4.4958) (end 7.0104 4.7244) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 4.7244) (end 8.0264 4.7244) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 4.7244) (end 8.0264 4.4958) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 4.4958) (end 7.0104 4.4958) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 4.0894) (end 7.0104 4.318) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 4.318) (end 8.0264 4.318) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 4.318) (end 8.0264 4.0894) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 4.0894) (end 7.0104 4.0894) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 3.683) (end 7.0104 3.9116) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 3.9116) (end 8.0264 3.9116) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 3.9116) (end 8.0264 3.683) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 3.683) (end 7.0104 3.683) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 3.2766) (end 7.0104 3.5052) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 3.5052) (end 8.0264 3.5052) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 3.5052) (end 8.0264 3.2766) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 3.2766) (end 7.0104 3.2766) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 2.8956) (end 7.0104 3.1242) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 3.1242) (end 8.0264 3.1242) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 3.1242) (end 8.0264 2.8956) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 2.8956) (end 7.0104 2.8956) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 2.4892) (end 7.0104 2.7178) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 2.7178) (end 8.0264 2.7178) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 2.7178) (end 8.0264 2.4892) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 2.4892) (end 7.0104 2.4892) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 2.0828) (end 7.0104 2.3114) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 2.3114) (end 8.0264 2.3114) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 2.3114) (end 8.0264 2.0828) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 2.0828) (end 7.0104 2.0828) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 1.6764) (end 7.0104 1.905) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 1.905) (end 8.0264 1.905) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 1.905) (end 8.0264 1.6764) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 1.6764) (end 7.0104 1.6764) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 1.2954) (end 7.0104 1.524) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 1.524) (end 8.0264 1.524) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 1.524) (end 8.0264 1.2954) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 1.2954) (end 7.0104 1.2954) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 0.889) (end 7.0104 1.1176) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 1.1176) (end 8.0264 1.1176) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 1.1176) (end 8.0264 0.889) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 0.889) (end 7.0104 0.889) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 0.4826) (end 7.0104 0.7112) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 0.7112) (end 8.0264 0.7112) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 0.7112) (end 8.0264 0.4826) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 0.4826) (end 7.0104 0.4826) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 0.0762) (end 7.0104 0.3048) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 0.3048) (end 8.0264 0.3048) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 0.3048) (end 8.0264 0.0762) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 0.0762) (end 7.0104 0.0762) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -0.3048) (end 7.0104 -0.0762) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -0.0762) (end 8.0264 -0.0762) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -0.0762) (end 8.0264 -0.3048) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -0.3048) (end 7.0104 -0.3048) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -0.7112) (end 7.0104 -0.4826) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -0.4826) (end 8.0264 -0.4826) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -0.4826) (end 8.0264 -0.7112) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -0.7112) (end 7.0104 -0.7112) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -1.1176) (end 7.0104 -0.889) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -0.889) (end 8.0264 -0.889) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -0.889) (end 8.0264 -1.1176) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -1.1176) (end 7.0104 -1.1176) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -1.524) (end 7.0104 -1.2954) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -1.2954) (end 8.0264 -1.2954) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -1.2954) (end 8.0264 -1.524) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -1.524) (end 7.0104 -1.524) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -1.905) (end 7.0104 -1.6764) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -1.6764) (end 8.0264 -1.6764) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -1.6764) (end 8.0264 -1.905) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -1.905) (end 7.0104 -1.905) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -2.3114) (end 7.0104 -2.0828) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -2.0828) (end 8.0264 -2.0828) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -2.0828) (end 8.0264 -2.3114) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -2.3114) (end 7.0104 -2.3114) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -2.7178) (end 7.0104 -2.4892) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -2.4892) (end 8.0264 -2.4892) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -2.4892) (end 8.0264 -2.7178) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -2.7178) (end 7.0104 -2.7178) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -3.1242) (end 7.0104 -2.8956) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -2.8956) (end 8.0264 -2.8956) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -2.8956) (end 8.0264 -3.1242) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -3.1242) (end 7.0104 -3.1242) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -3.5052) (end 7.0104 -3.2766) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -3.2766) (end 8.0264 -3.2766) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -3.2766) (end 8.0264 -3.5052) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -3.5052) (end 7.0104 -3.5052) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -3.9116) (end 7.0104 -3.683) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -3.683) (end 8.0264 -3.683) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -3.683) (end 8.0264 -3.9116) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -3.9116) (end 7.0104 -3.9116) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -4.318) (end 7.0104 -4.0894) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -4.0894) (end 8.0264 -4.0894) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -4.0894) (end 8.0264 -4.318) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -4.318) (end 7.0104 -4.318) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -4.7244) (end 7.0104 -4.4958) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -4.4958) (end 8.0264 -4.4958) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -4.4958) (end 8.0264 -4.7244) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -4.7244) (end 7.0104 -4.7244) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -5.1054) (end 7.0104 -4.8768) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -4.8768) (end 8.0264 -4.8768) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -4.8768) (end 8.0264 -5.1054) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -5.1054) (end 7.0104 -5.1054) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -5.5118) (end 7.0104 -5.2832) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -5.2832) (end 8.0264 -5.2832) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -5.2832) (end 8.0264 -5.5118) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -5.5118) (end 7.0104 -5.5118) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -5.9182) (end 7.0104 -5.6896) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -5.6896) (end 8.0264 -5.6896) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -5.6896) (end 8.0264 -5.9182) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -5.9182) (end 7.0104 -5.9182) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -6.3246) (end 7.0104 -6.096) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -6.096) (end 8.0264 -6.096) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -6.096) (end 8.0264 -6.3246) (layer Dwgs.User) (width 0.1524))
(fp_line (start 8.0264 -6.3246) (end 7.0104 -6.3246) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -5.7404) (end -5.7404 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 7.0104) (end 7.0104 7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 7.0104) (end 7.0104 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start 7.0104 -7.0104) (end -7.0104 -7.0104) (layer Dwgs.User) (width 0.1524))
(fp_line (start -7.0104 -7.0104) (end -7.0104 7.0104) (layer Dwgs.User) (width 0.1524))
(pad 1 smd rect (at -7.6454 -6.1976 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 2 smd rect (at -7.6454 -5.7912 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 3 smd rect (at -7.6454 -5.4102 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 4 smd rect (at -7.6454 -5.0038 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 5 smd rect (at -7.6454 -4.5974 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 6 smd rect (at -7.6454 -4.191 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 7 smd rect (at -7.6454 -3.81 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 8 smd rect (at -7.6454 -3.4036 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 9 smd rect (at -7.6454 -2.9972 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 10 smd rect (at -7.6454 -2.5908 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 11 smd rect (at -7.6454 -2.2098 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 12 smd rect (at -7.6454 -1.8034 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 13 smd rect (at -7.6454 -1.397 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 14 smd rect (at -7.6454 -0.9906 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 15 smd rect (at -7.6454 -0.6096 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 16 smd rect (at -7.6454 -0.2032 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 17 smd rect (at -7.6454 0.2032 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 18 smd rect (at -7.6454 0.6096 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 19 smd rect (at -7.6454 0.9906 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 20 smd rect (at -7.6454 1.397 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 21 smd rect (at -7.6454 1.8034 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 22 smd rect (at -7.6454 2.2098 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 23 smd rect (at -7.6454 2.5908 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 24 smd rect (at -7.6454 2.9972 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 25 smd rect (at -7.6454 3.4036 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 26 smd rect (at -7.6454 3.81 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 27 smd rect (at -7.6454 4.191 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 28 smd rect (at -7.6454 4.5974 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 29 smd rect (at -7.6454 5.0038 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 30 smd rect (at -7.6454 5.4102 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 31 smd rect (at -7.6454 5.7912 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 32 smd rect (at -7.6454 6.1976 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 33 smd rect (at -6.1976 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 34 smd rect (at -5.7912 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 35 smd rect (at -5.4102 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 36 smd rect (at -5.0038 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 37 smd rect (at -4.5974 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 38 smd rect (at -4.191 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 39 smd rect (at -3.81 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 40 smd rect (at -3.4036 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 41 smd rect (at -2.9972 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 42 smd rect (at -2.5908 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 43 smd rect (at -2.2098 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 44 smd rect (at -1.8034 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 45 smd rect (at -1.397 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 46 smd rect (at -0.9906 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 47 smd rect (at -0.6096 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 48 smd rect (at -0.2032 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 49 smd rect (at 0.2032 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 50 smd rect (at 0.6096 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 51 smd rect (at 0.9906 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 52 smd rect (at 1.397 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 53 smd rect (at 1.8034 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 54 smd rect (at 2.2098 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 55 smd rect (at 2.5908 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 56 smd rect (at 2.9972 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 57 smd rect (at 3.4036 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 58 smd rect (at 3.81 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 59 smd rect (at 4.191 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 60 smd rect (at 4.5974 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 61 smd rect (at 5.0038 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 62 smd rect (at 5.4102 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 63 smd rect (at 5.7912 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 64 smd rect (at 6.1976 7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 65 smd rect (at 7.6454 6.1976 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 66 smd rect (at 7.6454 5.7912 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 67 smd rect (at 7.6454 5.4102 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 68 smd rect (at 7.6454 5.0038 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 69 smd rect (at 7.6454 4.5974 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 70 smd rect (at 7.6454 4.191 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 71 smd rect (at 7.6454 3.81 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 72 smd rect (at 7.6454 3.4036 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 73 smd rect (at 7.6454 2.9972 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 74 smd rect (at 7.6454 2.5908 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 75 smd rect (at 7.6454 2.2098 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 76 smd rect (at 7.6454 1.8034 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 77 smd rect (at 7.6454 1.397 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 78 smd rect (at 7.6454 0.9906 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 79 smd rect (at 7.6454 0.6096 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 80 smd rect (at 7.6454 0.2032 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 81 smd rect (at 7.6454 -0.2032 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 82 smd rect (at 7.6454 -0.6096 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 83 smd rect (at 7.6454 -0.9906 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 84 smd rect (at 7.6454 -1.397 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 85 smd rect (at 7.6454 -1.8034 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 86 smd rect (at 7.6454 -2.2098 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 87 smd rect (at 7.6454 -2.5908 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 88 smd rect (at 7.6454 -2.9972 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 89 smd rect (at 7.6454 -3.4036 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 90 smd rect (at 7.6454 -3.81 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 91 smd rect (at 7.6454 -4.191 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 92 smd rect (at 7.6454 -4.5974 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 93 smd rect (at 7.6454 -5.0038 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 94 smd rect (at 7.6454 -5.4102 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 95 smd rect (at 7.6454 -5.7912 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 96 smd rect (at 7.6454 -6.1976 270) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 97 smd rect (at 6.1976 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 98 smd rect (at 5.7912 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 99 smd rect (at 5.4102 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 100 smd rect (at 5.0038 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 101 smd rect (at 4.5974 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 102 smd rect (at 4.191 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 103 smd rect (at 3.81 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 104 smd rect (at 3.4036 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 105 smd rect (at 2.9972 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 106 smd rect (at 2.5908 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 107 smd rect (at 2.2098 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 108 smd rect (at 1.8034 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 109 smd rect (at 1.397 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 110 smd rect (at 0.9906 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 111 smd rect (at 0.6096 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 112 smd rect (at 0.2032 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 113 smd rect (at -0.2032 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 114 smd rect (at -0.6096 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 115 smd rect (at -0.9906 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 116 smd rect (at -1.397 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 117 smd rect (at -1.8034 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 118 smd rect (at -2.2098 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 119 smd rect (at -2.5908 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 120 smd rect (at -2.9972 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 121 smd rect (at -3.4036 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 122 smd rect (at -3.81 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 123 smd rect (at -4.191 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 124 smd rect (at -4.5974 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 125 smd rect (at -5.0038 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 126 smd rect (at -5.4102 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 127 smd rect (at -5.7912 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
(pad 128 smd rect (at -6.1976 -7.6454 180) (size 0.2286 1.4732) (layers F.Cu F.Paste F.Mask)
(solder_mask_margin 0.2))
)

18
hardware/rev1/kicad/proj_footprints.pretty/XTAL3_2X2_5.kicad_mod
View File

@ -1,18 +0,0 @@
(module XTAL3_2X2_5 (layer F.Cu) (tedit 580B09AE)
(fp_text reference REF** (at 0 -2.4) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value XTAL3_2X2_5 (at 0 3.1) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -2.4 1.2) (end -2.4 2) (layer F.SilkS) (width 0.15))
(fp_line (start -2.4 2) (end -1.6 2) (layer F.SilkS) (width 0.15))
(fp_line (start 1.1 -1.7) (end 2.1 -1.7) (layer F.SilkS) (width 0.15))
(fp_line (start 2.1 -1.7) (end 2.1 -0.8) (layer F.SilkS) (width 0.15))
(fp_line (start -2.1 0.7) (end -2.1 1.7) (layer F.SilkS) (width 0.15))
(fp_line (start -2.1 1.7) (end -1.1 1.7) (layer F.SilkS) (width 0.15))
(pad 3 smd rect (at 1.1 -0.8) (size 1.4 1.15) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 1.1 0.8) (size 1.4 1.15) (layers F.Cu F.Paste F.Mask))
(pad 1 smd rect (at -1.1 0.8) (size 1.4 1.15) (layers F.Cu F.Paste F.Mask))
(pad 4 smd rect (at -1.1 -0.8) (size 1.4 1.15) (layers F.Cu F.Paste F.Mask))
)

37
hardware/rev1/kicad/proj_footprints.pretty/bnc_90_1-1337543-0.kicad_mod
View File

@ -1,37 +0,0 @@
(module bnc_90_1-1337543-0 (layer F.Cu)
(descr "BNC connector, Tyco 1-1337543-0")
(fp_text reference bnc_90_1-1337543-0 (at 0 -14.9) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.2)))
)
(fp_text value VAL** (at 0 -16.4) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.2)))
)
(fp_line (start -6.4 1.2) (end 6.4 0.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 5.2) (end 6.4 4.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 4.2) (end 6.4 3.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 2.2) (end 6.4 1.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 3.2) (end 6.4 2.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 7.2) (end 6.4 6.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 6.2) (end 6.4 5.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 8.2) (end 6.4 7.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 9.2) (end 6.4 8.5) (layer F.SilkS) (width 0.3))
(fp_line (start 6.4 9.2) (end 6.4 0) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 9.2) (end -6.4 0) (layer F.SilkS) (width 0.3))
(fp_line (start 4.8 21.2) (end 4.8 9.2) (layer F.SilkS) (width 0.3))
(fp_line (start -4.8 21.2) (end -4.8 9.2) (layer F.SilkS) (width 0.3))
(fp_line (start -4.8 21.2) (end 4.8 21.2) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 9.2) (end 6.4 9.2) (layer F.SilkS) (width 0.3))
(fp_line (start 7.4 0) (end 7.4 -13.7) (layer F.SilkS) (width 0.3))
(fp_line (start -7.4 -13.7) (end -7.4 0) (layer F.SilkS) (width 0.3))
(fp_line (start -7.4 -13.7) (end 7.4 -13.7) (layer F.SilkS) (width 0.3))
(fp_line (start -7.4 0) (end 7.4 0) (layer F.SilkS) (width 0.3))
(pad 1 thru_hole circle (at 0 -12.38) (size 1.5 1.5) (drill 0.9) (layers *.Cu *.Mask F.SilkS))
(pad 2 thru_hole circle (at 2.54 -12.38) (size 1.5 1.5) (drill 0.9) (layers *.Cu *.Mask F.SilkS))
(pad "" np_thru_hole circle (at 5.08 -7.3) (size 2.1 2.1) (drill 2.1) (layers *.Cu *.Mask F.SilkS))
(pad "" np_thru_hole circle (at -5.08 -7.3) (size 2.1 2.1) (drill 2.1) (layers *.Cu *.Mask F.SilkS))
(model walter/conn_rf/bnc_90_1-1337543-0.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 0))
)
)

37
hardware/rev1/kicad/proj_footprints.pretty/bnc_90_1-1337543-0_ns.kicad_mod
View File

@ -1,37 +0,0 @@
(module proj_footprints:bnc_90_1-1337543-0 (layer F.Cu) (tedit 58FFF2B4)
(descr "BNC connector, Tyco 1-1337543-0")
(fp_text reference P1 (at -10.19 -11.258) (layer F.SilkS)
(effects (font (size 3 3) (thickness 0.3)))
)
(fp_text value BNC-90 (at 0 -16.4) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.2)))
)
(fp_line (start -6.4 1.2) (end 6.4 0.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 5.2) (end 6.4 4.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 4.2) (end 6.4 3.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 2.2) (end 6.4 1.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 3.2) (end 6.4 2.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 7.2) (end 6.4 6.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 6.2) (end 6.4 5.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 8.2) (end 6.4 7.5) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 9.2) (end 6.4 8.5) (layer F.SilkS) (width 0.3))
(fp_line (start 6.4 9.2) (end 6.4 0) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 9.2) (end -6.4 0) (layer F.SilkS) (width 0.3))
(fp_line (start 4.8 21.2) (end 4.8 9.2) (layer F.SilkS) (width 0.3))
(fp_line (start -4.8 21.2) (end -4.8 9.2) (layer F.SilkS) (width 0.3))
(fp_line (start -4.8 21.2) (end 4.8 21.2) (layer F.SilkS) (width 0.3))
(fp_line (start -6.4 9.2) (end 6.4 9.2) (layer F.SilkS) (width 0.3))
(fp_line (start 7.4 0) (end 7.4 -13.7) (layer F.SilkS) (width 0.3))
(fp_line (start -7.4 -13.7) (end -7.4 0) (layer F.SilkS) (width 0.3))
(fp_line (start -7.4 0) (end 7.4 0) (layer F.SilkS) (width 0.3))
(pad 1 thru_hole circle (at 0 -12.38) (size 1.5 1.5) (drill 0.9) (layers *.Cu *.Mask F.SilkS)
(solder_mask_margin 2) (clearance 2))
(pad 2 thru_hole circle (at 2.54 -12.38) (size 1.5 1.5) (drill 0.9) (layers *.Cu *.Mask F.SilkS))
(pad "" np_thru_hole circle (at 5.08 -7.3) (size 2.1 2.1) (drill 2.1) (layers *.Cu *.Mask F.SilkS))
(pad "" np_thru_hole circle (at -5.08 -7.3) (size 2.1 2.1) (drill 2.1) (layers *.Cu *.Mask F.SilkS))
(model walter/conn_rf/bnc_90_1-1337543-0.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 0))
)
)

BIN
hardware/rev2/IONPAK2_060318.pdf
View File

Binary file not shown.

5280
hardware/rev2/gerber/IONPAK2-B.Cu.gbr
View File

File diff suppressed because it is too large Load Diff

295
hardware/rev2/gerber/IONPAK2-B.Mask.gbr
View File

@ -1,295 +0,0 @@
G04 #@! TF.FileFunction,Soldermask,Bot*
%FSLAX46Y46*%
G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
G04 Created by KiCad (PCBNEW 4.0.2-stable) date 06/03/2018 00:18:55*
%MOMM*%
G01*
G04 APERTURE LIST*
%ADD10C,0.100000*%
%ADD11C,1.998980*%
%ADD12R,1.998980X1.998980*%
%ADD13R,1.300000X1.300000*%
%ADD14C,1.300000*%
%ADD15C,1.700000*%
%ADD16R,1.700000X1.700000*%
%ADD17R,1.727200X1.727200*%
%ADD18O,1.727200X1.727200*%
%ADD19O,3.600000X2.500000*%
%ADD20R,3.600000X2.500000*%
%ADD21O,2.500000X3.600000*%
%ADD22R,2.500000X3.600000*%
%ADD23C,1.600000*%
%ADD24O,1.600000X1.600000*%
%ADD25C,2.400000*%
%ADD26O,2.400000X2.400000*%
%ADD27C,2.400000*%
%ADD28C,3.750000*%
%ADD29C,1.250000*%
%ADD30R,2.100000X3.600000*%
%ADD31O,2.100000X3.600000*%
%ADD32O,1.700000X1.700000*%
%ADD33R,1.050000X1.050000*%
%ADD34C,1.050000*%
%ADD35R,1.800000X1.800000*%
%ADD36C,1.800000*%
%ADD37R,1.800000X3.600000*%
%ADD38O,1.800000X3.600000*%
%ADD39C,2.200000*%
%ADD40C,2.800000*%
%ADD41R,5.800000X5.800000*%
%ADD42C,1.600000*%
%ADD43O,1.800000X1.800000*%
%ADD44C,3.500000*%
%ADD45O,3.500000X5.000000*%
%ADD46O,8.000000X10.500000*%
%ADD47R,2.000000X2.600000*%
%ADD48O,2.000000X2.600000*%
%ADD49C,5.500000*%
%ADD50C,1.500000*%
%ADD51C,4.000000*%
G04 APERTURE END LIST*
D10*
X248893000Y-224500000D02*
G75*
G03X248893000Y-224500000I-1143000J0D01*
G01*
X254389000Y-227000000D02*
G75*
G03X254389000Y-227000000I-889000J0D01*
G01*
X249889000Y-227000000D02*
G75*
G03X249889000Y-227000000I-889000J0D01*
G01*
X255893000Y-224500000D02*
G75*
G03X255893000Y-224500000I-1143000J0D01*
G01*
D11*
X156464000Y-226824540D03*
D12*
X166624000Y-226824540D03*
D13*
X131826000Y-192024000D03*
D14*
X136826000Y-192024000D03*
D13*
X234696000Y-202438000D03*
D14*
X239696000Y-202438000D03*
D13*
X210566000Y-184912000D03*
D14*
X210566000Y-179912000D03*
D15*
X180340000Y-217250000D03*
D16*
X180340000Y-222250000D03*
D15*
X195580000Y-217250000D03*
D16*
X195580000Y-222250000D03*
D13*
X178054000Y-201422000D03*
D14*
X183054000Y-201422000D03*
D17*
X134620000Y-179832000D03*
D18*
X134620000Y-177292000D03*
X134620000Y-174752000D03*
X134620000Y-169672000D03*
X134620000Y-167132000D03*
X134620000Y-164592000D03*
X134620000Y-162052000D03*
D19*
X208026000Y-209804000D03*
X208026000Y-205994000D03*
X218186000Y-209804000D03*
X218186000Y-205994000D03*
X208026000Y-202184000D03*
X208026000Y-198374000D03*
D20*
X208026000Y-194564000D03*
D19*
X218186000Y-194564000D03*
X218186000Y-198374000D03*
X218186000Y-202184000D03*
D21*
X146558000Y-203962000D03*
X151638000Y-203962000D03*
X146558000Y-216662000D03*
X151638000Y-216662000D03*
X156718000Y-203962000D03*
X161798000Y-203962000D03*
D22*
X166878000Y-203962000D03*
D21*
X166878000Y-216662000D03*
X161798000Y-216662000D03*
X156718000Y-216662000D03*
D23*
X217932000Y-219202000D03*
D24*
X207772000Y-219202000D03*
D25*
X207010000Y-225552000D03*
D26*
X222250000Y-225552000D03*
D23*
X157480000Y-223266000D03*
D24*
X167640000Y-223266000D03*
D25*
X246761000Y-191770000D03*
D27*
X257537307Y-180993693D02*
X257537307Y-180993693D01*
D23*
X232791000Y-194310000D03*
D24*
X232791000Y-184150000D03*
D23*
X241554000Y-194183000D03*
D24*
X241554000Y-184023000D03*
D28*
X308356000Y-231902000D03*
D29*
X299466000Y-223012000D03*
D28*
X296924000Y-231902000D03*
D29*
X302006000Y-223012000D03*
X304546000Y-223012000D03*
X307086000Y-223012000D03*
X298196000Y-225552000D03*
X300736000Y-225552000D03*
X303276000Y-225552000D03*
X305816000Y-225552000D03*
D30*
X131000000Y-226000000D03*
D31*
X136080000Y-226000000D03*
D21*
X238160000Y-226080000D03*
X233080000Y-226080000D03*
D22*
X228000000Y-226080000D03*
X228000000Y-221000000D03*
D21*
X233080000Y-221000000D03*
X238160000Y-221000000D03*
D16*
X281432000Y-222758000D03*
D32*
X283972000Y-222758000D03*
X286512000Y-222758000D03*
X289052000Y-222758000D03*
X291592000Y-222758000D03*
D16*
X290322000Y-197866000D03*
D32*
X290322000Y-200406000D03*
X290322000Y-202946000D03*
X290322000Y-205486000D03*
X290322000Y-208026000D03*
X290322000Y-210566000D03*
D33*
X314198000Y-181864000D03*
D34*
X314198000Y-183134000D03*
X314198000Y-184404000D03*
X314198000Y-185674000D03*
X314198000Y-186944000D03*
X315468000Y-183134000D03*
X315468000Y-184404000D03*
X315468000Y-185674000D03*
X315468000Y-186944000D03*
X315468000Y-181864000D03*
D35*
X289000000Y-227000000D03*
D36*
X291540000Y-227000000D03*
D35*
X283000000Y-227000000D03*
D36*
X285540000Y-227000000D03*
D35*
X145000000Y-227000000D03*
D36*
X147540000Y-227000000D03*
D13*
X178054000Y-186944000D03*
D14*
X183054000Y-186944000D03*
D37*
X130810000Y-219456000D03*
D38*
X135890000Y-219456000D03*
D39*
X247750000Y-224500000D03*
X254750000Y-224500000D03*
D15*
X249000000Y-227000000D03*
X253500000Y-227000000D03*
D36*
X260286500Y-212153500D03*
X255206500Y-212153500D03*
D40*
X250126500Y-212153500D03*
D41*
X265366500Y-212153500D03*
D36*
X260286500Y-205359000D03*
X255206500Y-205359000D03*
D40*
X250126500Y-205359000D03*
D41*
X265366500Y-205359000D03*
D23*
X227330000Y-215900000D03*
D42*
X225565735Y-205894353D02*
X225565735Y-205894353D01*
D35*
X227457000Y-200406000D03*
D43*
X227457000Y-195326000D03*
D44*
X315000000Y-158000000D03*
X121000000Y-158000000D03*
D45*
X121000000Y-223500000D03*
D44*
X218000000Y-161000000D03*
D36*
X243586000Y-197104000D03*
X251206000Y-197104000D03*
D46*
X315000000Y-223500000D03*
D16*
X317500000Y-173228000D03*
D32*
X317500000Y-170688000D03*
X317500000Y-168148000D03*
X317500000Y-165608000D03*
D47*
X121920000Y-192024000D03*
D48*
X119380000Y-192024000D03*
D23*
X308229000Y-212598000D03*
D24*
X318389000Y-212598000D03*
D49*
X268000000Y-220620000D03*
D50*
X270540000Y-220620000D03*
D51*
X273080000Y-225700000D03*
X262920000Y-225700000D03*
D36*
X167132000Y-169418000D03*
X167132000Y-177038000D03*
M02*

13926
hardware/rev2/gerber/IONPAK2-F.Cu.gbr
View File

File diff suppressed because it is too large Load Diff

2264
hardware/rev2/gerber/IONPAK2-F.Mask.gbr
View File

File diff suppressed because it is too large Load Diff

1888
hardware/rev2/gerber/IONPAK2-F.Paste.gbr
View File

File diff suppressed because it is too large Load Diff

17845
hardware/rev2/gerber/IONPAK2-F.SilkS.gbr
View File

File diff suppressed because it is too large Load Diff

8399
hardware/rev2/gerber/IONPAK2-In1.Cu.gbr
View File

File diff suppressed because it is too large Load Diff

2203
hardware/rev2/gerber/IONPAK2-In2.Cu.gbr
View File

File diff suppressed because it is too large Load Diff

21
hardware/rev2/gerber/IONPAK2-Margin.gbr
View File

@ -1,21 +0,0 @@
G04 #@! TF.FileFunction,Other,User*
%FSLAX46Y46*%
G04 Gerber Fmt 4.6, Leading zero omitted, Abs format (unit mm)*
G04 Created by KiCad (PCBNEW 4.0.2-stable) date 06/03/2018 00:18:55*
%MOMM*%
G01*
G04 APERTURE LIST*
%ADD10C,0.100000*%
%ADD11C,0.200000*%
G04 APERTURE END LIST*
D10*
D11*
X115000000Y-235000000D02*
X115000000Y-152000000D01*
X321000000Y-235000000D02*
X115000000Y-235000000D01*
X321000000Y-152000000D02*
X321000000Y-235000000D01*
X115000000Y-152000000D02*
X321000000Y-152000000D01*
M02*

23
hardware/rev2/gerber/IONPAK2-NPTH.drl
View File

@ -1,23 +0,0 @@
M48
;DRILL file {KiCad 4.0.2-stable} date 06/03/2018 00:18:57
;FORMAT={-:-/ absolute / inch / decimal}
FMAT,2
INCH,TZ
T1C0.128
T2C0.138
%
G90
G05
M72
T1
X11.6899Y-9.13
X12.14Y-9.13
T2
X4.7638Y-6.2205
X8.5827Y-6.3386
X12.4016Y-6.2205
T2
X4.7638Y-8.7697G85X4.7638Y-8.8287
G05
T0
M30

431
hardware/rev2/gerber/IONPAK2.drl
View File

@ -1,431 +0,0 @@
M48
;DRILL file {KiCad 4.0.2-stable} date 06/03/2018 00:18:57
;FORMAT={-:-/ absolute / inch / decimal}
FMAT,2
INCH,TZ
T1C0.016
T2C0.026
T3C0.030
T4C0.031
T5C0.035
T6C0.039
T7C0.039
T8C0.040
T9C0.047
T10C0.050
T11C0.051
T12C0.055
T13C0.063
T14C0.087
T15C0.138
%
G90
G05
M72
T1
X4.675Y-6.582
X5.79Y-7.42
X5.82Y-7.
X5.82Y-7.39
X5.83Y-7.44
X5.85Y-7.41
X5.85Y-7.47
X5.86Y-7.61
X5.86Y-7.71
X5.86Y-7.79
X5.86Y-7.88
X5.86Y-8.84
X5.88Y-7.3
X5.88Y-7.4
X5.88Y-7.44
X5.96Y-7.88
X6.02Y-7.05
X6.09Y-7.88
X6.19Y-6.54
X6.68Y-7.54
X6.68Y-7.58
X6.68Y-7.62
X6.73Y-7.54
X6.73Y-7.58
X6.73Y-7.62
X6.78Y-7.54
X6.78Y-7.58
X6.78Y-7.62
X7.44Y-7.99
X7.44Y-8.06
X7.44Y-8.11
X7.45Y-7.42
X7.47Y-8.03
X7.47Y-8.08
X7.48Y-6.6
X7.49Y-7.98
X7.51Y-8.01
X7.51Y-8.06
X7.51Y-8.1
X7.57Y-7.42
X7.59Y-8.36
X7.61Y-8.4
X7.63Y-8.36
X7.64Y-7.14
X7.64Y-7.18
X7.65Y-8.4
X7.66Y-6.96
X7.67Y-8.36
X7.68Y-6.98
X7.69Y-8.4
X7.7Y-6.96
X7.71Y-8.36
X7.72Y-6.98
X7.74Y-6.66
X7.74Y-6.96
X7.88Y-8.09
X7.97Y-8.08
X7.97Y-8.17
X8.06Y-7.98
X8.06Y-8.08
X8.66Y-6.72
X8.66Y-7.22
X8.66Y-8.51
X8.7Y-8.46
X8.75Y-8.465
X8.785Y-6.46
X8.8Y-8.46
X8.835Y-8.51
X9.135Y-6.78
X9.2125Y-6.43
X9.275Y-6.765
X9.28Y-7.02
X9.29Y-6.94
X9.32Y-7.29
X9.3275Y-6.39
X9.33Y-6.94
X9.3325Y-6.2375
X9.335Y-6.77
X9.34Y-6.3
X9.35Y-7.29
X9.37Y-6.3
X9.38Y-7.02
X9.39Y-6.51
X9.47Y-6.24
X9.47Y-6.385
X9.54Y-6.82
X9.56Y-6.61
X9.65Y-6.73
X9.706Y-8.209
X9.71Y-8.49
X9.7318Y-7.2018
X9.77Y-6.71
X9.77Y-7.91
X9.88Y-7.65
X9.89Y-7.7
X9.97Y-7.83
X10.04Y-7.74
X10.06Y-6.49
X10.07Y-7.47
X10.16Y-6.24
X10.19Y-6.27
X10.21Y-7.75
X10.26Y-7.8
X10.38Y-6.44
X10.46Y-7.73
X10.56Y-7.73
X10.59Y-7.61
X10.6Y-7.47
X10.69Y-7.43
X10.7375Y-7.865
X10.75Y-7.44
X10.8Y-7.65
X10.82Y-6.381
X10.82Y-7.69
X10.86Y-6.46
X10.9Y-6.26
X10.9Y-6.31
X10.9375Y-6.1125
X10.94Y-6.31
X10.94Y-6.47
X10.94Y-7.18
X10.94Y-7.61
X10.94Y-8.68
X11.01Y-7.41
X11.023Y-6.489
X11.03Y-8.47
X11.035Y-6.295
X11.08Y-7.53
X11.085Y-7.71
X11.1Y-6.25
X11.1Y-7.632
X11.1275Y-7.8625
X11.14Y-6.83
X11.14Y-7.38
X11.15Y-6.45
X11.174Y-6.885
X11.188Y-6.583
X11.21Y-6.77
X11.21Y-6.81
X11.21Y-7.6
X11.21Y-7.71
X11.215Y-7.36
X11.2395Y-6.4325
X11.28Y-6.33
X11.28Y-7.53
X11.28Y-8.33
X11.283Y-6.568
X11.295Y-7.06
X11.3195Y-6.628
X11.32Y-6.31
X11.33Y-7.88
X11.33Y-8.1
X11.39Y-6.18
X11.39Y-7.06
X11.445Y-7.415
X11.46Y-6.44
X11.465Y-6.56
X11.4775Y-6.7685
X11.53Y-6.25
X11.535Y-6.485
X11.551Y-7.741
X11.575Y-8.03
X11.607Y-8.002
X11.61Y-6.835
X11.613Y-7.277
X11.621Y-7.124
X11.622Y-7.056
X11.63Y-6.405
X11.636Y-7.215
X11.665Y-7.858
X11.667Y-6.15
X11.675Y-8.17
X11.677Y-7.6965
X11.69Y-6.74
X11.701Y-7.121
X11.742Y-7.463
X11.759Y-7.2745
X11.76Y-6.98
X11.764Y-7.788
X11.788Y-7.406
X11.79Y-6.8425
X11.825Y-7.403
X11.828Y-7.858
X11.835Y-7.369
X11.838Y-8.018
X11.85Y-6.88
X11.854Y-6.981
X11.858Y-7.872
X11.862Y-7.4895
X11.875Y-8.12
X11.885Y-7.902
X11.89Y-6.44
X11.895Y-8.17
X11.9Y-8.135
X11.906Y-7.928
X11.91Y-6.74
X11.915Y-7.015
X11.9175Y-7.2785
X11.93Y-8.02
X11.95Y-7.84
X11.97Y-6.35
X11.97Y-7.38
X11.995Y-7.405
X12.Y-6.75
X12.02Y-7.1
X12.02Y-7.43
X12.024Y-7.6405
X12.032Y-7.151
X12.04Y-6.87
X12.04Y-8.09
X12.041Y-7.7505
X12.05Y-6.76
X12.062Y-7.2355
X12.075Y-7.7755
X12.078Y-7.407
X12.089Y-7.2085
X12.0945Y-7.7035
X12.11Y-6.88
X12.1115Y-6.7425
X12.12Y-6.48
X12.13Y-7.15
X12.13Y-8.22
X12.1435Y-7.7345
X12.1545Y-7.5015
X12.17Y-7.6725
X12.1745Y-7.5335
X12.175Y-6.875
X12.175Y-7.888
X12.18Y-8.185
X12.1809Y-7.3471
X12.198Y-7.8425
X12.2Y-6.695
X12.2035Y-7.553
X12.2075Y-6.9385
X12.24Y-6.8
X12.24Y-7.41
X12.24Y-7.641
X12.245Y-7.15
X12.293Y-7.995
X12.308Y-8.16
X12.313Y-7.4735
X12.3135Y-8.089
X12.328Y-7.8
X12.34Y-8.2
X12.399Y-7.037
X12.407Y-6.756
X12.419Y-8.206
X12.425Y-7.074
X12.5Y-7.57
X12.514Y-7.8595
T2
X12.37Y-7.16
X12.37Y-7.21
X12.37Y-7.26
X12.37Y-7.31
X12.37Y-7.36
X12.42Y-7.16
X12.42Y-7.21
X12.42Y-7.26
X12.42Y-7.31
X12.42Y-7.36
T3
X11.74Y-8.88
X11.79Y-8.78
X11.84Y-8.88
X11.89Y-8.78
X11.94Y-8.88
X11.99Y-8.78
X12.04Y-8.88
X12.09Y-8.78
T4
X5.19Y-7.56
X5.3869Y-7.56
X6.2Y-8.79
X6.58Y-6.67
X6.58Y-6.97
X6.6Y-8.79
X7.01Y-7.36
X7.01Y-7.93
X7.2069Y-7.36
X7.2069Y-7.93
X8.18Y-8.63
X8.29Y-7.0831
X8.29Y-7.28
X8.58Y-8.63
X8.8805Y-8.1061
X8.95Y-8.5
X9.165Y-7.25
X9.165Y-7.65
X9.24Y-7.97
X9.4369Y-7.97
X9.51Y-7.245
X9.51Y-7.645
X9.59Y-7.76
X9.8475Y-8.085
X9.8475Y-8.3525
X9.89Y-7.76
X10.0475Y-8.085
X10.0475Y-8.3525
X10.2475Y-8.085
X10.2475Y-8.3525
X10.4475Y-8.085
X10.4475Y-8.3525
X12.135Y-8.37
X12.535Y-8.37
T5
X5.7087Y-8.937
X5.8087Y-8.937
X10.5512Y-8.6858
X10.6512Y-8.6858
X11.1417Y-8.937
X11.2417Y-8.937
X11.378Y-8.937
X11.478Y-8.937
T6
X8.25Y-6.14
X8.955Y-7.69
X8.955Y-7.89
X9.8031Y-8.937
X9.9803Y-8.937
X10.2166Y-6.8634
X10.48Y-6.78
X10.48Y-7.01
X10.48Y-7.22
X10.68Y-6.78
X11.08Y-8.77
X11.18Y-8.77
X11.28Y-8.77
X11.38Y-8.77
X11.43Y-7.79
X11.43Y-7.89
X11.43Y-7.99
X11.43Y-8.09
X11.43Y-8.19
X11.43Y-8.29
X11.48Y-8.77
X12.5Y-6.52
X12.5Y-6.62
X12.5Y-6.72
X12.5Y-6.82
T7
X6.56Y-8.9301
T8
X5.3Y-6.38
X5.3Y-6.48
X5.3Y-6.58
X5.3Y-6.68
X5.3Y-6.88
X5.3Y-6.98
X5.3Y-7.08
T9
X4.7Y-7.56
X4.8Y-7.56
X5.15Y-8.64
X5.35Y-8.64
X7.1Y-8.5531
X7.1Y-8.75
X7.7Y-8.5531
X7.7Y-8.75
X8.15Y-8.88
X8.75Y-8.88
X9.715Y-7.55
X10.1393Y-7.1257
T10
X6.16Y-8.9301
T11
X8.19Y-7.81
X8.19Y-7.96
X8.19Y-8.11
X8.19Y-8.26
X8.59Y-7.66
X8.59Y-7.81
X8.59Y-7.96
X8.59Y-8.11
X8.59Y-8.26
X9.7539Y-8.8386
X10.0295Y-8.8386
T12
X5.1575Y-8.8976
X5.3575Y-8.8976
T13
X5.77Y-8.03
X5.77Y-8.53
X5.97Y-8.03
X5.97Y-8.53
X6.17Y-8.03
X6.17Y-8.53
X6.37Y-8.03
X6.37Y-8.53
X6.57Y-8.03
X6.57Y-8.53
X8.19Y-7.66
X8.9764Y-8.7008
X8.9764Y-8.9008
X9.1764Y-8.7008
X9.1764Y-8.9008
X9.3764Y-8.7008
X9.3764Y-8.9008
T14
X10.3512Y-8.8858
X10.7512Y-8.8858
T15
X12.4016Y-8.7697G85X12.4016Y-8.8287
G05
T0
M30

BIN
hardware/rev2/ionpak_bom_rev2.xls
View File

Binary file not shown.

1277
hardware/rev2/kicad/IONPAK2-cache.lib
View File

File diff suppressed because it is too large Load Diff

16200
hardware/rev2/kicad/IONPAK2.kicad_pcb
View File

File diff suppressed because it is too large Load Diff

4298
hardware/rev2/kicad/IONPAK2.net
View File

File diff suppressed because it is too large Load Diff

72
hardware/rev2/kicad/IONPAK2.pro
View File

@ -1,72 +0,0 @@
update=4/25/2017 11:39:52 PM
version=1
last_client=kicad
[pcbnew]
version=1
LastNetListRead=
UseCmpFile=1
PadDrill=0.600000000000
PadDrillOvalY=0.600000000000
PadSizeH=1.500000000000
PadSizeV=1.500000000000
PcbTextSizeV=1.500000000000
PcbTextSizeH=1.500000000000
PcbTextThickness=0.300000000000
ModuleTextSizeV=1.000000000000
ModuleTextSizeH=1.000000000000
ModuleTextSizeThickness=0.150000000000
SolderMaskClearance=0.000000000000
SolderMaskMinWidth=0.000000000000
DrawSegmentWidth=0.200000000000
BoardOutlineThickness=0.100000000000
ModuleOutlineThickness=0.150000000000
[cvpcb]
version=1
NetIExt=net
[general]
version=1
[eeschema]
version=1
LibDir=
[eeschema/libraries]
LibName1=power
LibName2=device
LibName3=transistors
LibName4=conn
LibName5=linear
LibName6=regul
LibName7=74xx
LibName8=cmos4000
LibName9=adc-dac
LibName10=memory
LibName11=xilinx
LibName12=microcontrollers
LibName13=dsp
LibName14=microchip
LibName15=analog_switches
LibName16=motorola
LibName17=texas
LibName18=intel
LibName19=audio
LibName20=interface
LibName21=digital-audio
LibName22=philips
LibName23=display
LibName24=cypress
LibName25=siliconi
LibName26=opto
LibName27=atmel
LibName28=contrib
LibName29=valves
LibName30=ionpak
LibName31=relays
[schematic_editor]
version=1
PageLayoutDescrFile=
PlotDirectoryName=
SubpartIdSeparator=0
SubpartFirstId=65
NetFmtName=Pcbnew
SpiceForceRefPrefix=0
SpiceUseNetNumbers=0
LabSize=60

7390
hardware/rev2/kicad/IONPAK2.sch
View File

File diff suppressed because it is too large Load Diff

5621
hardware/rev2/kicad/ionpak.lib
View File

File diff suppressed because it is too large Load Diff

16
hardware/rev2/kicad/proj_footprints.pretty/28F0121-0SR-10.kicad_mod
View File

@ -1,16 +0,0 @@
(module 28F0121-0SR-10 (layer F.Cu) (tedit 5825A986)
(fp_text reference REF** (at -0.2 -2.3) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value 28F0121-0SR-10 (at 0 2) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -2.1 -1) (end -2.1 -1.6) (layer F.SilkS) (width 0.15))
(fp_line (start -2.1 -1.6) (end 2.1 -1.6) (layer F.SilkS) (width 0.15))
(fp_line (start 2.1 -1.6) (end 2.1 -1) (layer F.SilkS) (width 0.15))
(fp_line (start -2.1 1.6) (end -2.1 1.1) (layer F.SilkS) (width 0.15))
(fp_line (start -2.1 1.6) (end 2.1 1.6) (layer F.SilkS) (width 0.15))
(fp_line (start 2.1 1.6) (end 2.1 1.1) (layer F.SilkS) (width 0.15))
(pad 1 smd rect (at -1.79 0) (size 2.77 1.47) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 1.79 0) (size 2.77 1.47) (layers F.Cu F.Paste F.Mask))
)

14
hardware/rev2/kicad/proj_footprints.pretty/3528RGB.kicad_mod
View File

@ -1,14 +0,0 @@
(module 3528RGB (layer F.Cu) (tedit 58B7D568)
(fp_text reference REF** (at 0 -2.4) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value LED3528RGB (at 0 3.1) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start 2.68 1.327) (end 2.68 2.127) (layer F.SilkS) (width 0.15))
(fp_line (start 1.791 2.127) (end 2.591 2.127) (layer F.SilkS) (width 0.15))
(pad 4 smd rect (at 1.5 -0.8) (size 1.5 1) (layers F.Cu F.Paste F.Mask))
(pad 1 smd rect (at 1.5 0.8) (size 1.5 1) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at -1.5 0.8) (size 1.5 1) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at -1.5 -0.8) (size 1.5 1) (layers F.Cu F.Paste F.Mask))
)

9
hardware/rev2/kicad/proj_footprints.pretty/3mm5_EARTH.kicad_mod
View File

@ -1,9 +0,0 @@
(module proj_footprints:3mm_EARTH (layer F.Cu) (tedit 59847D00)
(fp_text reference H4 (at 0 2.9) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value 3mm5_Mounting_Hole (at 0 -2.7) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(pad 1 thru_hole circle (at 0 0) (size 8 8) (drill 3.5) (layers *.Cu *.Mask F.SilkS))
)

9
hardware/rev2/kicad/proj_footprints.pretty/3mm_EARTH.kicad_mod
View File

@ -1,9 +0,0 @@
(module NPTH_3mm_ID (layer F.Cu) (tedit 58F9BBE4)
(fp_text reference H4 (at 0 2.9) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value 3mm_Mounting_Hole (at 0 -2.7) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(pad 1 thru_hole circle (at 0 0) (size 8 8) (drill 3) (layers *.Cu *.Mask F.SilkS))
)

29
hardware/rev2/kicad/proj_footprints.pretty/6-SMD.kicad_mod
View File

@ -1,29 +0,0 @@
(module 6-SMD (layer F.Cu) (tedit 58F98D57)
(descr "6-300 smd shape")
(tags "smd cms 6smd")
(attr smd)
(fp_text reference REF** (at 0.381 -1.143) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value 6-SMD (at 0 0.762) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -5.08 -2.54) (end -5.08 2.54) (layer F.SilkS) (width 0.15))
(fp_line (start -5.08 2.54) (end 2.54 2.54) (layer F.SilkS) (width 0.15))
(fp_line (start 2.54 2.54) (end 2.54 -2.54) (layer F.SilkS) (width 0.15))
(fp_line (start 2.54 -2.54) (end -5.08 -2.54) (layer F.SilkS) (width 0.15))
(fp_line (start -5.08 -1.27) (end -3.81 -1.27) (layer F.SilkS) (width 0.15))
(fp_line (start -3.81 -1.27) (end -3.81 1.27) (layer F.SilkS) (width 0.15))
(fp_line (start -3.81 1.27) (end -5.08 1.27) (layer F.SilkS) (width 0.15))
(pad 1 smd rect (at -3.81 4.635) (size 1.78 1.52) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at -1.27 4.635) (size 1.78 1.52) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at 1.27 4.635) (size 1.78 1.52) (layers F.Cu F.Paste F.Mask))
(pad 4 smd rect (at 1.27 -4.635) (size 1.78 1.52) (layers F.Cu F.Paste F.Mask))
(pad 5 smd rect (at -1.27 -4.635) (size 1.78 1.52) (layers F.Cu F.Paste F.Mask))
(pad 6 smd rect (at -3.81 -4.635) (size 1.78 1.52) (layers F.Cu F.Paste F.Mask))
(model SMD_Packages.3dshapes/6-SMD.wrl
(at (xyz 0 0 0))
(scale (xyz 1 0.5 0.8))
(rotate (xyz 0 0 0))
)
)

15
hardware/rev2/kicad/proj_footprints.pretty/BOURNS-GDT-2035TH.kicad_mod
View File

@ -1,15 +0,0 @@
(module proj_footprints:BOURNS-GDT-2035TH (layer F.Cu) (tedit 598482D8)
(descr "relay, Coto 9001 series Reed")
(fp_text reference GDT*** (at 0 -4.1) (layer F.SilkS)
(effects (font (thickness 0.3048)))
)
(fp_text value 2035 (at 0 4.3) (layer F.SilkS) hide
(effects (font (thickness 0.3048)))
)
(fp_line (start -3 -3) (end 3 -3) (layer F.SilkS) (width 0.3048))
(fp_line (start 3 -3) (end 3 3) (layer F.SilkS) (width 0.3048))
(fp_line (start -3 3) (end 3 3) (layer F.SilkS) (width 0.3048))
(fp_line (start -3 3) (end -3 -3) (layer F.SilkS) (width 0.3048))
(pad 1 thru_hole circle (at -3.81 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(pad 2 thru_hole circle (at 3.81 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
)

25
hardware/rev2/kicad/proj_footprints.pretty/BOURNS-GDT-2051.kicad_mod
View File

@ -1,25 +0,0 @@
(module BOURNS-GDT-2051 (layer F.Cu) (tedit 553CF70D)
(attr smd)
(fp_text reference REF** (at 0 0) (layer F.SilkS)
(effects (font (size 0.8 0.8) (thickness 0.15)))
)
(fp_text value BOURNS-GDT-2051 (at 0 0) (layer F.Fab)
(effects (font (size 0.8 0.8) (thickness 0.15)))
)
(fp_line (start -3 -2) (end 3 -2) (layer F.Fab) (width 0.2))
(fp_line (start 3 -2) (end 3 2) (layer F.Fab) (width 0.2))
(fp_line (start 3 2) (end -3 2) (layer F.Fab) (width 0.2))
(fp_line (start -3 2) (end -3 -2) (layer F.Fab) (width 0.2))
(fp_line (start 1 -1.5) (end 1 1.5) (layer F.SilkS) (width 0.2))
(fp_line (start 1 1.5) (end 0 0) (layer F.SilkS) (width 0.2))
(fp_line (start 0 0) (end 1 -1.5) (layer F.SilkS) (width 0.2))
(fp_line (start -1 -1.5) (end -1 1.5) (layer F.SilkS) (width 0.2))
(fp_line (start -1 1.5) (end 0 0) (layer F.SilkS) (width 0.2))
(fp_line (start 0 0) (end -1 -1.5) (layer F.SilkS) (width 0.2))
(fp_line (start -3.25 -2.35) (end 3.25 -2.35) (layer F.CrtYd) (width 0.2))
(fp_line (start 3.25 -2.35) (end 3.25 2.35) (layer F.CrtYd) (width 0.2))
(fp_line (start 3.25 2.35) (end -3.25 2.35) (layer F.CrtYd) (width 0.2))
(fp_line (start -3.25 2.35) (end -3.25 -2.35) (layer F.CrtYd) (width 0.2))
(pad 1 smd rect (at -2.25 0) (size 1.5 4.2) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 2.25 0) (size 1.5 4.2) (layers F.Cu F.Paste F.Mask))
)

19
hardware/rev2/kicad/proj_footprints.pretty/BOURNS-GDT-2051_ns.kicad_mod
View File

@ -1,19 +0,0 @@
(module proj_footprints:BOURNS-GDT-2051 (layer F.Cu) (tedit 58FF4C19)
(attr smd)
(fp_text reference GDT100 (at 3.81 3.048) (layer F.SilkS)
(effects (font (size 0.8 0.8) (thickness 0.15)))
)
(fp_text value 2051-09 (at 0 0) (layer F.Fab)
(effects (font (size 0.8 0.8) (thickness 0.15)))
)
(fp_line (start -3 -2) (end 3 -2) (layer F.Fab) (width 0.2))
(fp_line (start 3 -2) (end 3 2) (layer F.Fab) (width 0.2))
(fp_line (start 3 2) (end -3 2) (layer F.Fab) (width 0.2))
(fp_line (start -3 2) (end -3 -2) (layer F.Fab) (width 0.2))
(fp_line (start -3.25 -2.35) (end 3.25 -2.35) (layer F.CrtYd) (width 0.2))
(fp_line (start 3.25 -2.35) (end 3.25 2.35) (layer F.CrtYd) (width 0.2))
(fp_line (start 3.25 2.35) (end -3.25 2.35) (layer F.CrtYd) (width 0.2))
(fp_line (start -3.25 2.35) (end -3.25 -2.35) (layer F.CrtYd) (width 0.2))
(pad 1 smd rect (at -2.25 0) (size 1.5 4.2) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 2.25 0) (size 1.5 4.2) (layers F.Cu F.Paste F.Mask))
)

35
hardware/rev2/kicad/proj_footprints.pretty/COTO-9001.kicad_mod
View File

@ -1,35 +0,0 @@
(module relay_9001 (layer F.Cu) (tedit 58F9BC5C)
(descr "relay, Coto 9001 series Reed")
(fp_text reference RLY*** (at 0 -4.1) (layer F.SilkS)
(effects (font (thickness 0.3048)))
)
(fp_text value relay_9001 (at 0 4.3) (layer F.SilkS)
(effects (font (thickness 0.3048)))
)
(fp_line (start -8.6 -3) (end -8.6 3) (layer F.SilkS) (width 0.3048))
(fp_line (start 0.8 0) (end 2.5 0) (layer F.SilkS) (width 0.3048))
(fp_line (start -2.5 0) (end -0.8 0) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 0.8) (end 0.8 -0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 -0.8) (end 0.8 -0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start 0.8 -0.8) (end 0.8 0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 0.8) (end 0.8 0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 0.8) (end -0.8 -0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start 1.5 -1.8) (end 7.6 -1.8) (layer F.SilkS) (width 0.3048))
(fp_line (start 7.6 -1.8) (end 7.6 0) (layer F.SilkS) (width 0.3048))
(fp_line (start -7.6 -1.8) (end -7.6 0) (layer F.SilkS) (width 0.3048))
(fp_line (start -7.6 -1.8) (end -1.1 -1.8) (layer F.SilkS) (width 0.3048))
(fp_line (start -1.1 -1.8) (end 1.5 -2.3) (layer F.SilkS) (width 0.3048))
(fp_line (start 10.3 -3) (end 10.3 3) (layer F.SilkS) (width 0.3048))
(fp_line (start -10.3 -3) (end -10.3 3) (layer F.SilkS) (width 0.3048))
(fp_line (start -10.3 3) (end 10.3 3) (layer F.SilkS) (width 0.3048))
(fp_line (start -10.3 -3) (end 10.3 -3) (layer F.SilkS) (width 0.3048))
(pad 2 thru_hole circle (at -2.54 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(pad 3 thru_hole circle (at 2.54 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(pad 4 thru_hole circle (at 7.62 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(pad 1 thru_hole circle (at -7.62 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(model walter/relay/relay_9001.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 0))
)
)

29
hardware/rev2/kicad/proj_footprints.pretty/COTO-9001_ns.kicad_mod
View File

@ -1,29 +0,0 @@
(module proj_footprints:COTO-9001 (layer F.Cu) (tedit 58FF4F8B)
(descr "relay, Coto 9001 series Reed")
(fp_text reference RL101 (at 11.8745 0.889 90) (layer F.SilkS)
(effects (font (thickness 0.3048)))
)
(fp_text value 9001-05-02 (at 0 4.3) (layer F.SilkS)
(effects (font (thickness 0.3048)))
)
(fp_line (start 0.8 0) (end 2.5 0) (layer F.SilkS) (width 0.3048))
(fp_line (start -2.5 0) (end -0.8 0) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 0.8) (end 0.8 -0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 -0.8) (end 0.8 -0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start 0.8 -0.8) (end 0.8 0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 0.8) (end 0.8 0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start -0.8 0.8) (end -0.8 -0.8) (layer F.SilkS) (width 0.3048))
(fp_line (start 1.5 -1.8) (end 7.6 -1.8) (layer F.SilkS) (width 0.3048))
(fp_line (start 7.6 -1.8) (end 7.6 0) (layer F.SilkS) (width 0.3048))
(fp_line (start -1.1 -1.8) (end 1.5 -2.3) (layer F.SilkS) (width 0.3048))
(fp_line (start 10.3 -3) (end 10.3 3) (layer F.SilkS) (width 0.3048))
(pad 2 thru_hole circle (at -2.54 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(pad 3 thru_hole circle (at 2.54 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(pad 4 thru_hole circle (at 7.62 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(pad 1 thru_hole rect (at -7.62 0) (size 1.8 1.8) (drill 0.8) (layers *.Cu *.Mask F.SilkS))
(model walter/relay/relay_9001.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 0))
)
)

29
hardware/rev2/kicad/proj_footprints.pretty/C_1206_ns.kicad_mod
View File

@ -1,29 +0,0 @@
(module Capacitors_SMD:C_1206 (layer F.Cu) (tedit 58FF4D39)
(descr "Capacitor SMD 1206, reflow soldering, AVX (see smccp.pdf)")
(tags "capacitor 1206")
(attr smd)
(fp_text reference C100 (at 5.208549 1.796051) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value DNP/1206 (at 0 2) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text user %R (at 0 -1.75) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -1.6 0.8) (end -1.6 -0.8) (layer F.Fab) (width 0.1))
(fp_line (start 1.6 0.8) (end -1.6 0.8) (layer F.Fab) (width 0.1))
(fp_line (start 1.6 -0.8) (end 1.6 0.8) (layer F.Fab) (width 0.1))
(fp_line (start -1.6 -0.8) (end 1.6 -0.8) (layer F.Fab) (width 0.1))
(fp_line (start -2.25 -1.05) (end 2.25 -1.05) (layer F.CrtYd) (width 0.05))
(fp_line (start -2.25 -1.05) (end -2.25 1.05) (layer F.CrtYd) (width 0.05))
(fp_line (start 2.25 1.05) (end 2.25 -1.05) (layer F.CrtYd) (width 0.05))
(fp_line (start 2.25 1.05) (end -2.25 1.05) (layer F.CrtYd) (width 0.05))
(pad 1 smd rect (at -1.5 0) (size 1 1.6) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 1.5 0) (size 1 1.6) (layers F.Cu F.Paste F.Mask))
(model Capacitors_SMD.3dshapes/C_1206.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 0))
)
)

25
hardware/rev2/kicad/proj_footprints.pretty/DO-214AB.kicad_mod
View File

@ -1,25 +0,0 @@
(module DO-214AB (layer F.Cu) (tedit 5825692F)
(descr "Jedec DO-214AB diode package. Designed according to Fairchild SS32 datasheet.")
(tags "DO-214AB diode")
(attr smd)
(fp_text reference REF** (at 0 -4.2) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value DO-214AB (at 0 4.6) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -5.5 -2.6) (end -5.5 2.5) (layer F.SilkS) (width 0.15))
(fp_line (start -5.15 -3.45) (end 5.15 -3.45) (layer F.CrtYd) (width 0.05))
(fp_line (start 5.15 -3.45) (end 5.15 3.45) (layer F.CrtYd) (width 0.05))
(fp_line (start 5.15 3.45) (end -5.15 3.45) (layer F.CrtYd) (width 0.05))
(fp_line (start -5.15 3.45) (end -5.15 -3.45) (layer F.CrtYd) (width 0.05))
(fp_line (start 3.5 3.2) (end -4.8 3.2) (layer F.SilkS) (width 0.15))
(fp_line (start -4.8 -3.2) (end 3.5 -3.2) (layer F.SilkS) (width 0.15))
(pad 2 smd rect (at 3.6 0) (size 2.6 3.2) (layers F.Cu F.Paste F.Mask))
(pad 1 smd rect (at -3.6 0) (size 2.6 3.2) (layers F.Cu F.Paste F.Mask))
(model Diodes_SMD.3dshapes/DO-214AB.wrl
(at (xyz 0 0 0))
(scale (xyz 0.39 0.39 0.39))
(rotate (xyz 0 0 180))
)
)

17
hardware/rev2/kicad/proj_footprints.pretty/DO-214AC.kicad_mod
View File

@ -1,17 +0,0 @@
(module DO-214AC (layer F.Cu) (tedit 5833D139)
(fp_text reference REF** (at -1.5 2.7) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value DO-214AC (at -0.1 0) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -0.9 -1.4) (end -0.9 1.4) (layer F.SilkS) (width 0.15))
(fp_line (start -2.3 -1.4) (end -2.3 -1.1) (layer F.SilkS) (width 0.15))
(fp_line (start 2.3 1.1) (end 2.3 1.4) (layer F.SilkS) (width 0.15))
(fp_line (start 2.3 1.4) (end -2.3 1.4) (layer F.SilkS) (width 0.15))
(fp_line (start -2.3 1.4) (end -2.3 1.1) (layer F.SilkS) (width 0.15))
(fp_line (start -2.3 -1.4) (end 2.3 -1.4) (layer F.SilkS) (width 0.15))
(fp_line (start 2.3 -1.4) (end 2.3 -1.1) (layer F.SilkS) (width 0.15))
(pad 1 smd rect (at -2.2 0) (size 2.1 1.8) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 2.2 0) (size 2.1 1.8) (layers F.Cu F.Paste F.Mask))
)

29
hardware/rev2/kicad/proj_footprints.pretty/DPAK.kicad_mod
View File

@ -1,29 +0,0 @@
(module DPAK (layer F.Cu) (tedit 4FF970FF)
(descr "MOS boitier DPACK G-D-S")
(tags "CMD DPACK")
(attr smd)
(fp_text reference DPAK (at 0 -10.414) (layer F.SilkS)
(effects (font (size 0.29972 0.29972) (thickness 0.0762)))
)
(fp_text value VAL** (at 0 -4.39928) (layer F.SilkS)
(effects (font (size 0.29972 0.29972) (thickness 0.0762)))
)
(fp_line (start 1.34874 1.69926) (end 1.34874 -3.2004) (layer F.SilkS) (width 0.381))
(fp_line (start 1.34874 1.69926) (end 3.2512 1.69926) (layer F.SilkS) (width 0.381))
(fp_line (start 3.2512 1.69926) (end 3.2512 -3.2004) (layer F.SilkS) (width 0.381))
(fp_line (start -3.2512 1.651) (end -3.2512 -3.2004) (layer F.SilkS) (width 0.381))
(fp_line (start -3.2512 1.651) (end -1.34874 1.651) (layer F.SilkS) (width 0.381))
(fp_line (start -1.34874 1.651) (end -1.34874 -3.2004) (layer F.SilkS) (width 0.381))
(fp_line (start -3.44932 -10.09904) (end 3.44932 -10.09904) (layer F.SilkS) (width 0.381))
(fp_line (start 3.44932 -10.09904) (end 3.44932 -3.2004) (layer F.SilkS) (width 0.381))
(fp_line (start 3.44932 -3.2004) (end -3.44932 -3.2004) (layer F.SilkS) (width 0.381))
(fp_line (start -3.44932 -3.2004) (end -3.44932 -10.09904) (layer F.SilkS) (width 0.381))
(pad 1 smd rect (at -2.30124 0) (size 1.651 3.048) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at 0 -6.64972) (size 6.70052 6.70052) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 2.30124 0) (size 1.651 3.048) (layers F.Cu F.Paste F.Mask))
(model smd/dpack_2.wrl
(at (xyz 0 0 0))
(scale (xyz 1 1 1))
(rotate (xyz 0 0 0))
)
)

23
hardware/rev2/kicad/proj_footprints.pretty/FCI_54601-908WPLF.kicad_mod
View File

@ -1,23 +0,0 @@
(module FCI_54601-908WPLF locked (layer F.Cu) (tedit 58343208)
(fp_text reference J2 (at 14.6 6) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value NET_OUT (at 5.7 0.1) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start 13.4 -1.8) (end 13.4 -5.2) (layer F.SilkS) (width 0.15))
(fp_line (start -2 -1.8) (end -2 -5.2) (layer F.SilkS) (width 0.15))
(fp_line (start -2 10.2) (end -2 1.8) (layer F.SilkS) (width 0.15))
(fp_line (start 13.4 10.2) (end 13.4 1.8) (layer F.SilkS) (width 0.15))
(fp_line (start 13.416 10.2) (end -1.984 10.2) (layer F.SilkS) (width 0.15))
(pad "" np_thru_hole circle (at 0 0) (size 3.75 3.75) (drill 3.25) (layers *.Cu *.Mask F.SilkS))
(pad 2 thru_hole circle (at 8.89 8.89) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
(pad "" np_thru_hole circle (at 11.432 0) (size 3.75 3.75) (drill 3.25) (layers *.Cu *.Mask F.SilkS))
(pad 4 thru_hole circle (at 6.35 8.89) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
(pad 6 thru_hole circle (at 3.81 8.89) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
(pad 8 thru_hole circle (at 1.27 8.89) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
(pad 1 thru_hole circle (at 10.16 6.35) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
(pad 3 thru_hole circle (at 7.62 6.35) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
(pad 5 thru_hole circle (at 5.08 6.35) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
(pad 7 thru_hole circle (at 2.54 6.35) (size 1.25 1.25) (drill 0.76) (layers *.Cu *.Mask F.SilkS))
)

31
hardware/rev2/kicad/proj_footprints.pretty/H2019FNL.kicad_mod
View File

@ -1,31 +0,0 @@
(module H2019FNL (layer F.Cu) (tedit 582FE01B)
(fp_text reference REF** (at -4.8 6.4 180) (layer F.SilkS)
(effects (font (size 1.2 1.2) (thickness 0.15)))
)
(fp_text value H2019FNL (at 0 0) (layer F.Fab)
(effects (font (size 1.2 1.2) (thickness 0.15)))
)
(fp_circle (center -5.6 3.4) (end -6.1 3.6) (layer F.SilkS) (width 0.15))
(fp_line (start 5 4.6) (end 6.4 4.6) (layer F.SilkS) (width 0.15))
(fp_line (start 6.4 4.6) (end 6.4 -4.6) (layer F.SilkS) (width 0.15))
(fp_line (start 6.4 -4.6) (end 5 -4.6) (layer F.SilkS) (width 0.15))
(fp_line (start -5 -4.6) (end -6.4 -4.6) (layer F.SilkS) (width 0.15))
(fp_line (start -6.4 -4.6) (end -6.4 4.6) (layer F.SilkS) (width 0.15))
(fp_line (start -6.4 4.6) (end -5 4.6) (layer F.SilkS) (width 0.15))
(pad 16 smd rect (at -4.445 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 1 smd rect (at -4.445 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 15 smd rect (at -3.175 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at -3.175 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 14 smd rect (at -1.905 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at -1.905 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 13 smd rect (at -0.635 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 4 smd rect (at -0.635 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 12 smd rect (at 0.635 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 5 smd rect (at 0.635 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 11 smd rect (at 1.905 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 6 smd rect (at 1.905 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 10 smd rect (at 3.175 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 7 smd rect (at 3.175 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 9 smd rect (at 4.445 -4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
(pad 8 smd rect (at 4.445 4.255) (size 0.76 1.65) (layers F.Cu F.Paste F.Mask))
)

9
hardware/rev2/kicad/proj_footprints.pretty/NPTH_3mm5_ID.kicad_mod
View File

@ -1,9 +0,0 @@
(module proj_footprints:NPTH_3mm_ID (layer F.Cu) (tedit 59847C9F)
(fp_text reference H4 (at 0 2.9) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value 3mm5_Mounting_Hole (at 0 -2.7) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(pad "" np_thru_hole circle (at 0 0) (size 3.5 3.5) (drill 3.5) (layers *.Cu *.Mask))
)

9
hardware/rev2/kicad/proj_footprints.pretty/NPTH_3mm_ID.kicad_mod
View File

@ -1,9 +0,0 @@
(module NPTH_3mm_ID (layer F.Cu) (tedit 58345150)
(fp_text reference H4 (at 0 2.9) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value 3mm_Mounting_Hole (at 0 -2.7) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(pad "" np_thru_hole circle (at 0 0) (size 3 3) (drill 3) (layers *.Cu *.Mask))
)

18
hardware/rev2/kicad/proj_footprints.pretty/OPTO-SMD4.kicad_mod
View File

@ -1,18 +0,0 @@
(module OPTO-SMD4 (layer F.Cu) (tedit 53451140)
(fp_text reference U7 (at 0 1.30048) (layer F.SilkS)
(effects (font (size 0.29972 0.29972) (thickness 0.0762)))
)
(fp_text value LTV-817 (at 0 0) (layer F.SilkS)
(effects (font (size 0.29972 0.29972) (thickness 0.0762)))
)
(fp_line (start -2.4 -3.25) (end 2.4 -3.25) (layer F.SilkS) (width 0.15))
(fp_line (start -2.4 3.25) (end 2.4 3.25) (layer F.SilkS) (width 0.15))
(fp_line (start 2.39998 -3.24866) (end 2.39998 3.24866) (layer F.SilkS) (width 0.15))
(fp_line (start -2.39998 -3.24866) (end -2.39998 3.24866) (layer F.SilkS) (width 0.15))
(fp_line (start -2.39998 2.64922) (end -1.798 2.64922) (layer F.SilkS) (width 0.15))
(fp_line (start -1.798 2.64922) (end -1.798 3.24866) (layer F.SilkS) (width 0.15))
(pad 1 smd rect (at -1.27 4.49834 180) (size 1.4986 1.29794) (layers F.Cu F.Paste F.Mask))
(pad 2 smd rect (at 1.27 4.49834 180) (size 1.4986 1.29794) (layers F.Cu F.Paste F.Mask))
(pad 3 smd rect (at 1.27 -4.5) (size 1.4986 1.29794) (layers F.Cu F.Paste F.Mask))
(pad 4 smd rect (at -1.27 -4.5) (size 1.4986 1.29794) (layers F.Cu F.Paste F.Mask))
)

24
hardware/rev2/kicad/proj_footprints.pretty/PhoenixContact_1786417_03.kicad_mod
View File

@ -1,24 +0,0 @@
(module Connectors_Phoenix:PhoenixContact_MC-G_03x5.08mm_Angled (layer F.Cu) (tedit 58F9A094)
(descr PhoenixContact_1786417_03x5.08mm_Angled)
(tags "phoenix_contact connector 01x03_G_5.08mm")
(fp_text reference REF** (at 4.826 -4.064) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value PhoenixContact_1786417_03x5.08mm_Angled (at 5.08 9.5) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -2.62 -3) (end -2.62 16) (layer F.SilkS) (width 0.15))
(fp_line (start -2.62 16) (end 12.78 16) (layer F.SilkS) (width 0.15))
(fp_line (start 12.78 16) (end 12.78 -3) (layer F.SilkS) (width 0.15))
(fp_line (start -2.62 -3) (end 12.78 -3) (layer F.SilkS) (width 0.15))
(fp_line (start -2.62 8) (end 12.78 8) (layer F.SilkS) (width 0.15))
(fp_line (start 0 -2.3) (end 0.3 -2.9) (layer F.SilkS) (width 0.15))
(fp_line (start 0.3 -2.9) (end -0.3 -2.9) (layer F.SilkS) (width 0.15))
(fp_line (start -0.3 -2.9) (end 0 -2.3) (layer F.SilkS) (width 0.15))
(pad 3 thru_hole oval (at 10.16 5.08) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 2 thru_hole oval (at 5.08 5.08) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 1 thru_hole rect (at 0 5.08) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 1 thru_hole rect (at 0 0) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 2 thru_hole oval (at 5.08 0) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
(pad 3 thru_hole oval (at 10.16 0) (size 2.5 3.6) (drill 1.6) (layers *.Cu *.Mask))
)

32
hardware/rev2/kicad/proj_footprints.pretty/Pin_Header_Straight_2x05_Pitch1.27mm.kicad_mod
View File

@ -1,32 +0,0 @@
(module Pin_Header_Straight_2x05_Pitch1.27mm (layer F.Cu) (tedit 58705FA3)
(descr "Through hole pin header, pitch 1.27mm")
(tags "pin header")
(fp_text reference REF** (at -1.8 0 90) (layer F.SilkS)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_text value PH2X05VR1MM27 (at 0 6.9) (layer F.Fab)
(effects (font (size 1 1) (thickness 0.15)))
)
(fp_line (start -1.1 0.5) (end -1.1 -1.1) (layer F.SilkS) (width 0.15))
(fp_line (start -1.1 -1.1) (end 0.5 -1.1) (layer F.SilkS) (width 0.15))
(fp_line (start 2.1 -0.8) (end 1.3 -0.8) (layer F.SilkS) (width 0.15))
(fp_line (start 2.1 5.85) (end 2.1 -0.8) (layer F.SilkS) (width 0.15))
(fp_line (start 2.1 5.85) (end -0.85 5.85) (layer F.SilkS) (width 0.15))
(fp_line (start -1.1 -1.05) (end -1.1 6.1) (layer F.CrtYd) (width 0.05))
(fp_line (start 2.35 -1.05) (end 2.35 6.1) (layer F.CrtYd) (width 0.05))
(fp_line (start -1.1 -1.05) (end 2.35 -1.05) (layer F.CrtYd) (width 0.05))
(fp_line (start -1.1 6.1) (end 2.35 6.1) (layer F.CrtYd) (width 0.05))
(fp_line (start -0.85 5.85) (end -0.85 1.3) (layer F.SilkS) (width 0.15))
(fp_line (start 0.5 -0.8) (end -0.85 -0.8) (layer F.SilkS) (width 0.15))
(fp_line (start -0.85 -0.8) (end -0.85 0.5) (layer F.SilkS) (width 0.15))
(pad 1 thru_hole rect (at 0 0) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 3 thru_hole circle (at 0 1.27) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 5 thru_hole circle (at 0 2.54) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 7 thru_hole circle (at 0 3.81) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 9 thru_hole circle (at 0 5.08) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 4 thru_hole circle (at 1.27 1.27) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 6 thru_hole circle (at 1.27 2.54) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 8 thru_hole circle (at 1.27 3.81) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 10 thru_hole circle (at 1.27 5.08) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
(pad 2 thru_hole circle (at 1.27 0) (size 1.05 1.05) (drill 0.65) (layers *.Cu *.Mask F.SilkS))
)

Some files were not shown because too many files have changed in this diff Show More