fast-servo/pyfastservo/adc.py

@@ -17,6 +17,8 @@
 # You should have received a copy of the GNU General Public License
 # along with this program. If not, see <https://www.gnu.org/licenses/>.
 
+import mmap
+import os
 
 import spidev
 from pyfastservo.common import (
@@ -31,8 +33,6 @@ from pyfastservo.common import (
     AUX_ADC_ADDR,
     MAP_MASK,
     PAGESIZE,
-    write_to_memory,
-    read_from_memory
 )
 
 # /dev/spidev1.0  <=> spidev<BUS>.<DEVICE>
@@ -44,118 +44,276 @@ AUX_ADC_PORT_A = 2
 AUX_ADC_PORT_B = 3
 
 
-def spi_write(spi, address, value):
+def main_adc_config(test_pattern):
-    spi.xfer2([address, value])
-
-def spi_read(spi, address):
-    rx_buffer = spi.xfer2([0x80 | address, 0x00])
-    return rx_buffer[1]
-
-def main_adc_config(spi, test_pattern):
     high_word = (test_pattern & 0xFF00) >> 8
     low_word = test_pattern & 0xFF
 
-    spi_write(spi, 0x00, 0x80)              # reset
-    spi_write(spi, 0x01, 0x20)              # REGISTER A1: set to Two's complement Data Format
-    spi_write(spi, 0x02, 0x15)              # REGISTER A2: set to LVDS output, set 4 data lanes and turn on test mode
-    spi_write(spi, 0x03, high_word)         # REGISTER A3: test pattern high word
-    spi_write(spi, 0x04, low_word)          # REGISTER A4: test pattern low word
-
-def main_adc_test_mode(spi, enable):
-    reg_contents = 0x15 if enable else 0x11 # set to LVDS output, set 4 data lanes and turn on or off test mode
-    spi_write(spi, 0x02, reg_contents)
-
-def verify_adc_registers(spi, reg_to_check):
-    for register, expected_value in reg_to_check.items():
-        value = spi_read(spi, register)
-        print(f"Spi readback register 0x{register:02x}: 0x{value:02x}")
-        if value != expected_value:
-            print(f"Different value read than sent in reg 0x{register:02x}")
-
-def read_frame():
-    return read_from_memory(ADC_FRAME_ADDR, 1)[0]
-
-def perform_bitslip():
-    for i in range(4):
-        current_frame = read_frame()
-        if current_frame != 0x0C:
-            print(f"Performing bitslip (iteration: {i}). Current frame: 0x{current_frame:02x}")
-            write_to_memory(ADC_BITSLIP_ADDR, 1)
-        else:
-            print(f"No bitslip required; Current frame: 0x{current_frame:02x}")
-            return
-
-def find_edge():
-    prev_frame = read_frame()
-    transition = False
-    for tap_delay in range(32):
-        write_to_memory(ADC_DELAY_ADDR, tap_delay)
-        current_frame = read_frame()
-
-        print(f"Tap delay: {tap_delay}, Current frame: 0x{current_frame:02x}")
-
-        if current_frame != prev_frame:
-            if not transition:
-                transition = True
-            else:
-                final_delay = (tap_delay // 2) + 2
-                print(f"Edge detected; setting iDelay to: {final_delay}")
-                write_to_memory(ADC_DELAY_ADDR, final_delay)
-                return
-
-        prev_frame = current_frame
-
-    # If no edge detected
-    final_delay = 11
-    print(f"No edge detected; setting iDelay to: {final_delay}")
-    write_to_memory(ADC_DELAY_ADDR, final_delay)
-
-def read_adc_channel(high_addr, low_addr):
-    return (read_from_memory(high_addr, 1)[0] << 8) | read_from_memory(low_addr, 1)[0]
-
-def print_adc_channels():
-    adc_ch0 = read_adc_channel(ADC_CH0_HIGH_ADDR, ADC_CH0_LOW_ADDR)
-    adc_ch1 = read_adc_channel(ADC_CH1_HIGH_ADDR, ADC_CH1_LOW_ADDR)
-    print(f"Final ADC_CH0: 0x{adc_ch0:04x}")
-    print(f"Final ADC_CH1: 0x{adc_ch1:04x}")
-
-def enable_adc_afe(ch1_x10=False, ch2_x10=False):
-    ctrl_value = (ch2_x10 << 1) | ch1_x10
-    write_to_memory(ADC_AFE_CTRL_ADDR, ctrl_value)
-    afe_ctrl = read_from_memory(ADC_AFE_CTRL_ADDR, 1)[0]
-    print(f"ADC_AFE_CTRL: 0x{afe_ctrl:02X}")
-    return afe_ctrl
-
-def configure_ltc2195():
     spi = spidev.SpiDev()
+
     try:
         spi.open(MAIN_ADC_BUS, MAIN_ADC_DEVICE)
         spi.max_speed_hz = 50000
         spi.mode = 0b00  # CPOL = 0 CPHA = 0
         spi.cshigh = False
+        # spi.read0 = False
 
-        test_pattern = 0x811F
+        spi_buffer = [0x00, 0x80]  # reset
-        main_adc_config(spi, test_pattern)
+        rx_buffer = [0x00, 0x00]
 
-        verify_adc_registers(spi, {
+        spi.xfer2(spi_buffer)
-            0x01: 0x20,
-            0x02: 0x15,
-            0x03: (test_pattern & 0xFF00) >> 8,
-            0x04: test_pattern & 0xFF
-        })
 
-        # Performing Word Align
+        # REGISTER A1
-        perform_bitslip()
+        spi_buffer = [0x01, 0x20]  # set to Two's complement Data Format
-        find_edge()
+        spi.xfer2(spi_buffer)
-        print_adc_channels()
 
-        main_adc_test_mode(spi, False)
+        # read values back
-        verify_adc_registers(spi, {0x02: 0x11})  # Verify test mode is off
+        spi_buffer = [0x81, 0x00]
+        rx_buffer = spi.xfer2(spi_buffer)
+        print(f"Spi readback register 0x01: 0x{rx_buffer[1]:02x}")
+        if rx_buffer[1] != 0x20:
+            print("Different value read than sent in reg 0x02")
 
-        enable_adc_afe()
+        # REGISTER A2
+        spi_buffer = [
+            0x02,
+            0x15,
+        ]  # set to LVDS output, set 4 data lanes and turn on test mode
+        spi.xfer2(spi_buffer)
+
+        # read values back
+        spi_buffer = [0x82, 0x00]
+        rx_buffer = spi.xfer2(spi_buffer)
+        print(f"Spi readback register 0x02: 0x{rx_buffer[1]:02x}")
+        if rx_buffer[1] != 0x15:
+            print("Different value read than sent in reg 0x02")
+
+        # REGISTER A3
+        # test pattern high word
+        spi_buffer = [0x03, high_word]
+        spi.xfer2(spi_buffer)
+
+        # read balues back
+        spi_buffer = [0x83, 0x00]
+        rx_buffer = spi.xfer2(spi_buffer)
+        print(f"Spi readback register 0x03: 0x{rx_buffer[1]:02x}")
+        if rx_buffer[1] != high_word:
+            print("Different value read than sent in reg 0x03")
+
+        # REGISTER A4
+        # test pattern low word
+        spi_buffer = [0x04, low_word]
+        spi.xfer2(spi_buffer)
+
+        # read balues back
+        spi_buffer = [0x84, 0x00]
+        rx_buffer = spi.xfer2(spi_buffer)
+        print(f"Spi readback register 0x04: 0x{rx_buffer[1]:02x}")
+        if rx_buffer[1] != low_word:
+            print("Different value read than sent in reg 0x04")
+    finally:
+        spi.close()
+
+
+def main_adc_test_mode(enable):
+    spi = spidev.SpiDev()
+
+    try:
+        spi.open(MAIN_ADC_BUS, MAIN_ADC_DEVICE)
+        spi.max_speed_hz = 50000
+        spi.mode = 0b00  # CPOL = 0 CPHA = 0
+        spi.cshigh = False
+        # spi.read0 = True
+
+        reg_contents = (
+            0x15 if enable else 0x11
+        )  # set to LVDS output, set 4 data lanes and turn on or off test mode
+        spi_buffer = [0x02, reg_contents]
+        spi.xfer2(spi_buffer)
+
+        # read values back
+        spi_buffer = [0x82, 0x00]
+        rx_buffer = spi.xfer2(spi_buffer)
+        print(f"Spi readback register 0x02: 0x{rx_buffer[1]:02x}")
+        if rx_buffer[1] != reg_contents:
+            print("Different value read than sent in reg 0x02")
+    finally:
+        spi.close()
+
+
+def read_from_memory(address, n_bytes):
+    assert n_bytes <= 4
+    addr = address
+
+    try:
+        f = os.open("/dev/mem", os.O_SYNC | os.O_RDWR)
+        with mmap.mmap(
+            f,
+            PAGESIZE,
+            mmap.MAP_SHARED,
+            mmap.PROT_READ | mmap.PROT_WRITE,
+            offset=addr & ~MAP_MASK,
+        ) as mem:
+            start_addr = addr & MAP_MASK
+            stop_addr = start_addr + 4
+            # print(f"addr: 0x{addr:x}\tstart_addr: 0x{start_addr}\tstop_addr: 0x{stop_addr}")
+            contents = mem[start_addr:stop_addr]
+            read_value = list(contents)[:n_bytes]
+            # print("Read value: ", read_value)
+    finally:
+        os.close(f)
+
+    return read_value
+
+
+def write_to_memory(address, value):
+    value_bytes = value.to_bytes(4, "little")
+    addr = address
+
+    try:
+        f = os.open("/dev/mem", os.O_SYNC | os.O_RDWR)
+        with mmap.mmap(
+            f,
+            PAGESIZE,
+            mmap.MAP_SHARED,
+            mmap.PROT_READ | mmap.PROT_WRITE,
+            offset=addr & ~MAP_MASK,
+        ) as mem:
+            start_addr = addr & MAP_MASK
+            stop_addr = start_addr + 4
+            # print(f"addr: 0x{addr:x}\tstart_addr: 0x{start_addr}\tstop_addr: 0x{stop_addr}")
+            mem[start_addr:stop_addr] = value_bytes
+            contents = mem[start_addr:stop_addr]
+            # print("Read value: ", list(contents), " written value: ", list(value_bytes))
+    finally:
+        os.close(f)
+
+
+def word_align():
+
+    value = 0
+    edge_detected = False
+    transition = False
+    tap_delay = 0
+
+    for i in range(4):
+        current_frame = read_from_memory(ADC_FRAME_ADDR, 1)[0]
+        if current_frame != 0x0C:
+            print(
+                f"Performing bitslip (bitslip iteration: {i}). Reason: current_frame is 0x{current_frame:02x} instead of 0x0C"
+            )
+            write_to_memory(ADC_BITSLIP_ADDR, 1)
+        else:
+            print(f"No bitslip required; Currernt frame = 0x{current_frame:02x}")
+            break
+
+    current_frame = read_from_memory(ADC_FRAME_ADDR, 1)[0]
+    prev_frame = current_frame
+
+    for i in range(32):
+        write_to_memory(ADC_DELAY_ADDR, tap_delay)
+        if edge_detected == 1:
+            break
+        current_frame = read_from_memory(ADC_FRAME_ADDR, 1)[0]
+
+        print(f"Tap delay: {tap_delay}")
+        print(f"Current frame: 0x{current_frame:02x}")
+
+        if current_frame == prev_frame:
+            tap_delay += 1
+        elif not transition:
+            tap_delay += 1
+            transition = True
+        elif transition:
+            tap_delay = i // 2
+            edge_detected = True
+
+        prev_frame = current_frame
+
+    if not edge_detected:
+        tap_delay = 11  # empirically tested to work best
+        write_to_memory(ADC_DELAY_ADDR, tap_delay)
+        print(f"No edge detected; setting iDelay to: {tap_delay}")
+    if edge_detected:
+        write_to_memory(ADC_DELAY_ADDR, tap_delay + 2)
+        print(f"Edge detected; setting iDelay to (tap_delay + 2): {tap_delay} + 2")
+
+    adc_ch0 = read_from_memory(ADC_CH0_HIGH_ADDR, 4)
+    print(f"ADC_CH0: 0x{adc_ch0}")
+
+    adc_ch0 = (read_from_memory(ADC_CH0_HIGH_ADDR, 1)[0] << 8) | read_from_memory(
+        ADC_CH0_LOW_ADDR, 1
+    )[0]
+    adc_ch1 = (read_from_memory(ADC_CH1_HIGH_ADDR, 1)[0] << 8) | read_from_memory(
+        ADC_CH1_LOW_ADDR, 1
+    )[0]
+    print(f"Final ADC_CH0: 0x{adc_ch0:04x}")
+    print(f"Final ADC_CH1: 0x{adc_ch1:04x}")
+
+
+def modify_bit(original_value, position, bit_value):
+    mask = 1 << position
+    return (original_value & ~mask) | (bit_value << position)
+
+
+def adc_aux_config():
+    # MSB to LSB
+    # | RANGE | ADDR [2:0] | DIFF |
+    #       DIFF = 0    =>  configure as single ended (it is negated in gateware)
+    #       RANGE = 0   =>  configure as 0-2.5 Vref
+    to_write = 0b00000
+    write_to_memory(AUX_ADC_ADDR, to_write)
+
+
+def adc_aux_read(port, type, pin):
+    # port:
+    #   1 - port A
+    #   2 - port B
+    # type:
+    #   0 - single-ended
+    #   1 - differential
+    # pin:
+    #   0b000   - VA1/VB1
+    #   0b001   - VA2/VB2
+    #   0b010   - VA3/VB3
+    #   0b011   - VA4/VB4
+
+    assert type in (0, 1)
+    assert port in (1, 2)
+
+    write_buffer = [0, 0]
+    read_buffer = [0, 0]
+
+    aux_config_reg = read_from_memory(AUX_ADC_ADDR, 1)[0]
+    aux_config = (aux_config_reg & 0b10001) | pin << 1
+    write_to_memory(AUX_ADC_ADDR, aux_config)
+
+    spi = spidev.SpiDev()
+    try:
+        spi.open(1, 3)  # AUX ADC 1?
+        spi.max_speed_hz = 5000
+        spi.mode = 0b00
+        spi.cshigh = False
+
+        read_buffer = spi.xfer2(write_buffer)
+        mu_voltage = read_buffer[0] << 8 | read_buffer[1] >> 2
+        print(f"MU_voltage: 0x{mu_voltage:04X}")
+        print(f"Read_buffer[0]: 0x{read_buffer[0]:02X}")
+        print(f"Read_buffer[1]: 0x{read_buffer[1]:02X}")
+        return mu_voltage * 2.5 / 4096
 
     finally:
         spi.close()
 
+
+def main():
+    main_adc_config(0x811F)
+    word_align()
+
+    main_adc_test_mode(False)
+
+    write_to_memory(ADC_AFE_CTRL_ADDR, 0b1100) # {-, -, ch2_X10, ch1_X10}
+    print(read_from_memory(ADC_AFE_CTRL_ADDR, 1)[0])
+
+
 if __name__ == "__main__":
-    configure_ltc2195()
+    main()

fast-servo/pyfastservo/common.py

@@ -17,9 +17,6 @@
 # You should have received a copy of the GNU General Public License
 # along with this program. If not, see <https://www.gnu.org/licenses/>.
 
-import os
-import mmap
-
 CSR_SIZE = 0x800
 MAP_SIZE = 0x1000
 MAP_MASK = 0xFFF
@@ -75,46 +72,3 @@ CH0_HIGH_WORD_ADDR      =   DAC_BASE_ADDR + CH0_HIGH_WORD_OFFSET
 CH0_LOW_WORD_ADDR       =   DAC_BASE_ADDR + CH0_LOW_WORD_OFFSET
 CH1_HIGH_WORD_ADDR      =   DAC_BASE_ADDR + CH1_HIGH_WORD_OFFSET
 CH1_LOW_WORD_ADDR       =   DAC_BASE_ADDR + CH1_LOW_WORD_OFFSET
-
-
-def read_from_memory(address, n_bytes):
-    assert n_bytes <= 4
-    addr = address
-
-    try:
-        f = os.open("/dev/mem", os.O_SYNC | os.O_RDWR)
-        with mmap.mmap(
-            f,
-            PAGESIZE,
-            mmap.MAP_SHARED,
-            mmap.PROT_READ | mmap.PROT_WRITE,
-            offset=addr & ~MAP_MASK,
-        ) as mem:
-            start_addr = addr & MAP_MASK
-            stop_addr = start_addr + 4
-            contents = mem[start_addr:stop_addr]
-            read_value = list(contents)[:n_bytes]
-    finally:
-        os.close(f)
-
-    return read_value
-
-def write_to_memory(address, value):
-    value_bytes = value.to_bytes(4, "little")
-    addr = address
-
-    try:
-        f = os.open("/dev/mem", os.O_SYNC | os.O_RDWR)
-        with mmap.mmap(
-            f,
-            PAGESIZE,
-            mmap.MAP_SHARED,
-            mmap.PROT_READ | mmap.PROT_WRITE,
-            offset=addr & ~MAP_MASK,
-        ) as mem:
-            start_addr = addr & MAP_MASK
-            stop_addr = start_addr + 4
-            mem[start_addr:stop_addr] = value_bytes
-            contents = mem[start_addr:stop_addr]
-    finally:
-        os.close(f)

fast-servo/pyfastservo/dac.py

@@ -17,7 +17,8 @@
 # You should have received a copy of the GNU General Public License
 # along with this program. If not, see <https://www.gnu.org/licenses/>.
 
-import time
+import mmap
+import os
 
 import spidev
 from pyfastservo.common import (
@@ -28,58 +29,108 @@ from pyfastservo.common import (
     CTRL_ADDR,
     MAP_MASK,
     PAGESIZE,
-    write_to_memory,
-    read_from_memory
 )
 
 # /dev/spidev2.0  <=> spidev<BUS>.<DEVICE>
 MAIN_DAC_BUS = 2
 MAIN_DAC_DEVICE = 0
+
 DAC_VERSION = 0x0A
 
 
-def spi_write(spi, address, value):
+def main_dac_init():
-    spi.xfer2([address, value])
+    spi = spidev.SpiDev()
 
-def spi_read(spi, address):
+    try:
-    rx_buffer = spi.xfer2([0x80 | address, 0x00])
+        spi.open(MAIN_DAC_BUS, MAIN_DAC_DEVICE)
-    return rx_buffer[1]
+        spi.max_speed_hz = 5000
+        spi.mode = 0b00  # CPOL = 0 CPHA = 0
+        spi.cshigh = False
 
-def hard_reset(spi):
+        spi_buffer = [0x00, 0x10]  # software reset
-    spi_write(spi, 0x00, 0x10)  # Software reset
+        spi.xfer2(spi_buffer)
-    spi_write(spi, 0x00, 0x00)  # Release software reset
-    spi_read(spi, 0x00)         # Read reset address (necessary for reset to take effect)
 
-def check_version(spi):
+        spi_buffer = [0x00, 0x00]  # release software reset
-    version = spi_read(spi, 0x1F)
+        spi.xfer2(spi_buffer)
-    print(f"DAC version: 0x{version:02X}")
-    return version == DAC_VERSION
 
-def configure_dac(spi):
+        spi_buffer = [
-    power_down_reg = spi_read(spi, 0x01)
+            0x80,
-    spi_write(spi, 0x01, power_down_reg & ~(1 << 0))  # Clear EXTREF bit for internal reference
+            0x00,
-    spi_write(spi, 0x0D, 0x00)      # Set RREF to 10 kΩ for 1.0V reference
+        ]  # for some reason it is needed to read the reset address for reset to actually reset
-    spi_write(spi, 0x04, 0xA0)      # Enable on-chip IRSET (1.6 kΩ for 20mA output)
+        rx_buffer = spi.xfer2(spi_buffer)
-    spi_write(spi, 0x07, 0xA0)      # Enable on-chip QRSET (1.6 kΩ for 20mA output)
-    spi_write(spi, 0x05, 0x00)      # Disable internal IRCML
-    spi_write(spi, 0x08, 0x00)      # Disable internal QRCML
-    spi_write(spi, 0x02, 0xB4)      # Enable 2's complement, LVDS interface, 4 LVDS lanes
 
-def dac_self_calibration(spi):
+        spi_buffer = [0x9F, 0x00]  # hardware version
-    spi_write(spi, 0x12, 0x00)      # Reset calibration status
+        rx_buffer = spi.xfer2(spi_buffer)
-    spi_write(spi, 0x0E, 0x08)      # Enable calibration clock, default divide ratio
+        if rx_buffer[1] != DAC_VERSION:
-    spi_write(spi, 0x0E, 0x38)      # CALSELI = 1, CALSELQ = 1, CALCLK = 1
+            print(f"Unrecognized device: 0x{rx_buffer[1]:02X}")
-    spi_write(spi, 0x12, 0x10)      # Set CALEN bit
 
-    while True:
+        print("=== Contents of spi buffer after DAC VERSION read back: ===")
-        status = spi_read(spi, 0x0F)
+        print(f"0x{rx_buffer[0]:02X}{rx_buffer[1]:02X}")
-        if status & 0xC0 == 0xC0:   # Both CALSTATI and CALSTATQ are 1
+
-            break
+        spi_buffer = [0x82, 00]
-        time.sleep(0.01)
+        rx_buffer = spi.xfer2(spi_buffer)
+        print(f"0x{rx_buffer[0]:02X}{rx_buffer[1]:02X}")
+
+        # set to 2's complement and I to be first of pair on data input pads
+        spi_buffer = [0x02, 0xB4]
+        rx_buffer = spi.xfer2(spi_buffer)
+        spi_buffer = [0x82, 00]
+        rx_buffer = spi.xfer2(spi_buffer)
+        print(f"0x{rx_buffer[0]:02X}{rx_buffer[1]:02X}")
+
+        for i in range(10):
+            spi_buffer = [0x94, 0x00]
+            rx_buffer = spi.xfer2(spi_buffer)
+            print(f"0x{rx_buffer[0]:02X}{rx_buffer[1]:02X}")
+
+    finally:
+        spi.close()
+
+
+def read_from_memory(address, n_bytes):
+    assert n_bytes <= 4
+    addr = address
+
+    try:
+        f = os.open("/dev/mem", os.O_SYNC | os.O_RDWR)
+        with mmap.mmap(
+            f,
+            PAGESIZE,
+            mmap.MAP_SHARED,
+            mmap.PROT_READ | mmap.PROT_WRITE,
+            offset=addr & ~MAP_MASK,
+        ) as mem:
+            start_addr = addr & MAP_MASK
+            stop_addr = start_addr + 4
+            # print(f"addr: 0x{addr:x}\tstart_addr: 0x{start_addr}\tstop_addr: 0x{stop_addr}")
+            contents = mem[start_addr:stop_addr]
+            read_value = list(contents)[:n_bytes]
+    finally:
+        os.close(f)
+
+    return read_value
+
+
+def write_to_memory(address, value):
+    value_bytes = value.to_bytes(4, "little")
+    addr = address
+
+    try:
+        f = os.open("/dev/mem", os.O_SYNC | os.O_RDWR)
+        with mmap.mmap(
+            f,
+            PAGESIZE,
+            mmap.MAP_SHARED,
+            mmap.PROT_READ | mmap.PROT_WRITE,
+            offset=addr & ~MAP_MASK,
+        ) as mem:
+            start_addr = addr & MAP_MASK
+            stop_addr = start_addr + 4
+            mem[start_addr:stop_addr] = value_bytes
+            contents = mem[start_addr:stop_addr]
+    finally:
+        os.close(f)
 
-    spi_write(spi, 0x12, 0x00)      # Clear calibration bits
-    spi_write(spi, 0x0E, 0x30)      # Keep CALSELI and CALSELQ set, clear CALCLK
-    print("DAC self-calibration completed")
 
 def manual_override(enable=True):
     reg_contents = read_from_memory(CTRL_ADDR, 1)[0]
@@ -87,6 +138,7 @@ def manual_override(enable=True):
     to_write = reg_contents | 0b1 if enable else reg_contents & 0b110
     write_to_memory(CTRL_ADDR, to_write)
 
+
 def power_down(channel, power_down=True):
     assert channel in (0, 1)
 
@@ -100,49 +152,31 @@ def power_down(channel, power_down=True):
     reg_contents = read_from_memory(CTRL_ADDR, 1)[0]
     print(f"REG contents: 0b{reg_contents:03b}")
 
-def set_dac_output(value):
-    value = min(value, 0x3FFF)
-    low_word = value & 0xFF
-    high_word = (value >> 8) & 0x3F
 
-    write_to_memory(CH0_HIGH_WORD_ADDR, high_word)
+def write_sample(channel, sample):
-    write_to_memory(CH0_LOW_WORD_ADDR, low_word)
+    assert channel in (0, 1)
-    write_to_memory(CH1_HIGH_WORD_ADDR, high_word)
+    if channel == 0:
-    write_to_memory(CH1_LOW_WORD_ADDR, low_word)
+        addresses = [CH0_HIGH_WORD_ADDR, CH0_LOW_WORD_ADDR]
-    print(f"DAC output set to: 0x{value:04X}")
+    else:
+        addresses = [CH1_HIGH_WORD_ADDR, CH1_LOW_WORD_ADDR]
 
-def configure_ad9117():
+    low_word_value = sample & 0xFF
-    spi = spidev.SpiDev()
+    high_word_value = (sample >> 8) & 0x3F
-    spi.open(MAIN_DAC_BUS, MAIN_DAC_DEVICE)
+    values = [high_word_value, low_word_value]
-    spi.max_speed_hz = 5000
+    for addr, value in zip(addresses, values):
-    spi.mode = 0b00  # CPOL = 0 CPHA = 0
+        write_to_memory(addr, value)
-    spi.cshigh = False
 
-    try:
-        hard_reset(spi)
-        if not check_version(spi):
-            print("Unrecognized DAC version")
-            return False
 
-        configure_dac(spi)
+def write_ramp():
-        dac_self_calibration(spi)
+    signal = [i for i in range(16384)]
 
+    for value in signal:
+        write_sample(0, value)
+
+def main():
+    main_dac_init()
     power_down(0, False)
     power_down(1, False)
-        manual_override(True)
-
-        # Enable DAC outputs
-        spi_write(spi, 0x01, spi_read(spi, 0x01) & ~((1 << 4) | (1 << 3)))
-
-        print("AD9117 configuration completed successfully")
-        return True
-
-    except Exception as e:
-        print(f"Error configuring AD9117: {e}")
-        return False
-
-    finally:
-        spi.close()
     
 if __name__ == "__main__":
-    configure_ad9117()
+    main()

fast-servo/pyfastservo/initialize.py

@@ -21,8 +21,8 @@ from pyfastservo import adc, si5340, dac
 
 def main():
     si5340.configure_si5340()
-    adc.configure_ltc2195()
+    adc.main()
-    dac.configure_ad9117()
+    dac.main()
 
 if __name__ == "__main__":
     main()

fast-servo/pyfastservo/si5340.py

@@ -35,15 +35,6 @@ STATUS_LOSREF = 0x04
 STATUS_LOL = 0x08
 
 
-def write_register(bus, address, value):
-    try:
-        page = address >> 8
-        register = address & 0xFF
-        bus.write_byte_data(IC_ADDR, 0x01, page)
-        bus.write_byte_data(IC_ADDR, register, value)
-    except Exception as e:
-        raise Exception(f"Write failed 0x{value:02X} at 0x{address:04X}: {e}")
-
 def write_preamble(bus):
     preamble = [
         (0x0B24, 0xC0),
@@ -54,7 +45,7 @@ def write_preamble(bus):
         (0x0B4E, 0x1A),
     ]
     for address, value in preamble:
-        write_register(bus, address, value)
+        bus.write_byte_data(IC_ADDR, address, value)
 
 def write_postamble(bus):
     postamble = [
@@ -63,7 +54,7 @@ def write_postamble(bus):
         (0x0B25, 0x02),
     ]
     for address, value in postamble:
-        write_register(bus, address, value)
+        bus.write_byte_data(IC_ADDR, address, value)
 
 def wait_device_ready(bus):
     for _ in range(15):
@@ -253,7 +244,7 @@ def configure_si5340():
 
         print("Writing main configuration...")
         for address, value in main_config:
-            write_register(bus, address, value)
+            bus.write_byte_data(IC_ADDR, address, value)
         print("Main configuration written")
 
         write_postamble(bus)