assembly/src/hw/stabilizer.md

# Sinara 8452 DSP Stabilizer

* [Wiki](https://github.com/sinara-hw/Stabilizer/wiki)
* [QUARTIQ Manual](https://quartiq.de/stabilizer/)
* [Firmware](https://github.com/quartiq/stabilizer)

EEM is used for power only, and it can be alternatively powered by 12V barrel jack or PoE.

## JSON

Not present in the JSON.

## Getting the firmware

You can get the firmware from [Hydra](https://nixbld.m-labs.hk/jobset/mcu/mcu-contrib).

* ``stabilizer-dual-iir`` supports Pounder v1.2 - probably you should flash this one,
* ``stabilizer-dual-iir-pounder_v1_0`` supports Pounder 1.0 and 1.1 (legacy),
* ``stabilizer-lockin`` is a different application which we do not usually flash.

These all include changes to the mainline code to include Pounder telemetry.

### Building (optional)

Please keep in mind that the firmware from the official Quartiq repository does not include support for Pounder in MQTT, you may need to use a fork for that. But if the stabilizer is without a Pounder, it's also a valid option.

There is no Nix Flake support to make things easier, so you need to set up rust and cargo manually. Start with cloning the stabilizer repository and opening a new shell with dfu-util (for flashing) and rustup (for building).

```
nix-shell -p dfu-util rustup
```

Set up the toolchain, this should be done only once:

```
rustup target add thumbv7em-none-eabihf
cargo install cargo-binutils
rustup component add llvm-tools-preview
rustup update
rustup default stable
```

Building:

```
cargo build --release
cargo objcopy --release --bin dual-iir -- -O binary dual-iir.bin
```

## Flashing

Once you have the binary, you can now flash it.

Without firmware on the device or with older firmware (without USB serial console), you need to use the jumper method:

1. Have the Stabilizer disconnected from power.
2. Use a jumper of some sort to short BOOT pins on the board.
3. Turn on the power.
4. You can remove the jumper after few seconds.

With newer firmware with USB serial console:

1. Connect the Stabilizer to power.
2. Connect USB cable to the Stabilizer.
3. Connect with a serial console emulator, usually at ``/dev/ttyACM0``.
4. Input ``platform dfu`` in the console.

And for both:

5. The device is now in DFU mode.
6. Flash the device with the following command:

```
dfu-util -a 0 -s 0x08000000:leave -R -D dual-iir.bin
```

7. Look for "File downloaded successfully".

For normal usage, the stabilizer must be configured with USB console later (try ``help`` command first), to set its IP address and MQTT broker address. However, for general testing (like the one below), you don't need to configure it any further.

## Testing

1. Ensure that the [firmware](#getting-the-firmware) has been flashed onto the Stabilizer
2. Turn on the crate/Stabilizer via EEM cable or power supply
3. Set up the signal generator for an amplitude of 1V, frequency of 10kHz, and a sine wave
4. Use the splitter to connect the generator's output to ADC0 and to the oscilloscope (refer to the picture below)
   ![](../img/stabilizer_signal_generator.jpg)
5. Configure the oscilloscope so that the sine wave is clearly visible
6. Connect the second channel of the oscilloscope to the Stabilizer's DAC0
7. Ensure that there is the same wave on the second channel, with a small delay, as on the first channel
8. Repeat steps 4-7 for ADC/DAC1 (refer to the picture below for connection reference)
   ![](../img/stabilizer_ports_match.jpg)