forked from M-Labs/thermostat
Compare commits
3 Commits
798b400aa5
...
0fe2d645e2
| Author | SHA1 | Date | |
|---|---|---|---|
| 0fe2d645e2 | |||
| ee26616c09 | |||
| c3b423b5f4 |
73
README.md
73
README.md
@ -92,43 +92,40 @@ ADC input data is provided in reports. Query for the latest report with the comm
|
||||
Send commands as simple text string terminated by `\n`. Responses are
|
||||
formatted as line-delimited JSON.
|
||||
|
||||
| Syntax | Function |
|
||||
|------------------------------------------- |-------------------------------------------------------------------------------|
|
||||
| `report` | Show current input |
|
||||
| `report mode` | Show current report mode |
|
||||
| `report mode <off/on>` | Set report mode |
|
||||
| `pwm` | Show current PWM settings |
|
||||
| `pwm <0/1> max_i_pos <amp>` | Set maximum positive output current, clamped to [0, 2] |
|
||||
| `pwm <0/1> max_i_neg <amp>` | Set maximum negative output current, clamped to [0, 2] |
|
||||
| `pwm <0/1> max_v <volt>` | Set maximum output voltage, clamped to [0, 4] |
|
||||
| `pwm <0/1> i_set <amp>` | Disengage PID, set fixed output current, clamped to [-2, 2] |
|
||||
| `pwm <0/1> polarity <normal/reversed>` | Set output current polarity, with 'normal' being the front panel polarity |
|
||||
| `pwm <0/1> pid` | Let output current to be controlled by the PID |
|
||||
| `center <0/1> <volt>` | Set the MAX1968 0A-centerpoint to the specified fixed voltage |
|
||||
| `center <0/1> vref` | Set the MAX1968 0A-centerpoint to measure from VREF |
|
||||
| `pid` | Show PID configuration |
|
||||
| `pid <0/1> target <deg_celsius>` | Set the PID controller target temperature |
|
||||
| `pid <0/1> kp <value>` | Set proportional gain |
|
||||
| `pid <0/1> ki <value>` | Set integral gain |
|
||||
| `pid <0/1> kd <value>` | Set differential gain |
|
||||
| `pid <0/1> output_min <amp>` | Set mininum output |
|
||||
| `pid <0/1> output_max <amp>` | Set maximum output |
|
||||
| `s-h` | Show Steinhart-Hart equation parameters |
|
||||
| `s-h <0/1> <t0/b/r0> <value>` | Set Steinhart-Hart parameter for a channel |
|
||||
| `postfilter` | Show postfilter settings |
|
||||
| `postfilter <0/1> off` | Disable postfilter |
|
||||
| `postfilter <0/1> rate <rate>` | Set postfilter output data rate |
|
||||
| `load [0/1]` | Restore configuration for channel all/0/1 from flash |
|
||||
| `save [0/1]` | Save configuration for channel all/0/1 to flash |
|
||||
| `reset` | Reset the device |
|
||||
| `dfu` | Reset device and enters USB device firmware update (DFU) mode |
|
||||
| `ipv4 <X.X.X.X/L> [Y.Y.Y.Y]` | Configure IPv4 address, netmask length, and optional default gateway |
|
||||
| `fan` | Show current fan settings and sensors' measurements |
|
||||
| `fan <value>` | Set fan power with values from 1 to 100 |
|
||||
| `fan auto` | Enable automatic fan speed control |
|
||||
| `fcurve <a> <b> <c>` | Set fan controller curve coefficients (see *Fan control* section) |
|
||||
| `fcurve default` | Set fan controller curve coefficients to defaults (see *Fan control* section) |
|
||||
| `hwrev` | Show hardware revision, and settings related to it |
|
||||
| Syntax | Function |
|
||||
|----------------------------------|-------------------------------------------------------------------------------|
|
||||
| `report` | Show current input |
|
||||
| `pwm` | Show current PWM settings |
|
||||
| `pwm <0/1> max_i_pos <amp>` | Set maximum positive output current, clamped to [0, 2] |
|
||||
| `pwm <0/1> max_i_neg <amp>` | Set maximum negative output current, clamped to [0, 2] |
|
||||
| `pwm <0/1> max_v <volt>` | Set maximum output voltage, clamped to [0, 4] |
|
||||
| `pwm <0/1> i_set <amp>` | Disengage PID, set fixed output current, clamped to [-2, 2] |
|
||||
| `pwm <0/1> pid` | Let output current to be controlled by the PID |
|
||||
| `center <0/1> <volt>` | Set the MAX1968 0A-centerpoint to the specified fixed voltage |
|
||||
| `center <0/1> vref` | Set the MAX1968 0A-centerpoint to measure from VREF |
|
||||
| `pid` | Show PID configuration |
|
||||
| `pid <0/1> target <deg_celsius>` | Set the PID controller target temperature |
|
||||
| `pid <0/1> kp <value>` | Set proportional gain |
|
||||
| `pid <0/1> ki <value>` | Set integral gain |
|
||||
| `pid <0/1> kd <value>` | Set differential gain |
|
||||
| `pid <0/1> output_min <amp>` | Set mininum output |
|
||||
| `pid <0/1> output_max <amp>` | Set maximum output |
|
||||
| `s-h` | Show Steinhart-Hart equation parameters |
|
||||
| `s-h <0/1> <t0/b/r0> <value>` | Set Steinhart-Hart parameter for a channel |
|
||||
| `postfilter` | Show postfilter settings |
|
||||
| `postfilter <0/1> off` | Disable postfilter |
|
||||
| `postfilter <0/1> rate <rate>` | Set postfilter output data rate |
|
||||
| `load [0/1]` | Restore configuration for channel all/0/1 from flash |
|
||||
| `save [0/1]` | Save configuration for channel all/0/1 to flash |
|
||||
| `reset` | Reset the device |
|
||||
| `dfu` | Reset device and enters USB device firmware update (DFU) mode |
|
||||
| `ipv4 <X.X.X.X/L> [Y.Y.Y.Y]` | Configure IPv4 address, netmask length, and optional default gateway |
|
||||
| `fan` | Show current fan settings and sensors' measurements |
|
||||
| `fan <value>` | Set fan power with values from 1 to 100 |
|
||||
| `fan auto` | Enable automatic fan speed control |
|
||||
| `fcurve <a> <b> <c>` | Set fan controller curve coefficients (see *Fan control* section) |
|
||||
| `fcurve default` | Set fan controller curve coefficients to defaults (see *Fan control* section) |
|
||||
| `hwrev` | Show hardware revision, and settings related to it |
|
||||
|
||||
|
||||
## USB
|
||||
@ -185,8 +182,6 @@ postfilter rate can be tuned with the `postfilter` command.
|
||||
|
||||
When using a TEC module with the Thermostat, the Thermostat expects the thermal load (where the thermistor is located) to cool down with a positive software current set point, and heat up with a negative current set point.
|
||||
|
||||
If the Thermostat is used for temperature control with the Sinara 5432 DAC "Zotino", and is connected via an IDC cable, the TEC polarity may need to be reversed with the `pwm <ch> polarity reversed` TCP command.
|
||||
|
||||
Testing heat flow direction with a low set current is recommended before installation of the TEC module.
|
||||
|
||||
### Limits
|
||||
|
||||
@ -57,14 +57,12 @@ class Client:
|
||||
'max_i_neg': 2.0,
|
||||
'max_v': 3.988,
|
||||
'max_i_pos': 2.0,
|
||||
'polarity': 'normal',
|
||||
{'channel': 1,
|
||||
'center': 'vref',
|
||||
'i_set': -0.02002179650216762,
|
||||
'max_i_neg': 2.0,
|
||||
'max_v': 3.988,
|
||||
'max_i_pos': 2.0}
|
||||
'polarity': 'normal',
|
||||
]
|
||||
"""
|
||||
return self._get_conf("pwm")
|
||||
|
||||
@ -18,7 +18,7 @@ use crate::{
|
||||
pid,
|
||||
config::PwmLimits,
|
||||
steinhart_hart as sh,
|
||||
command_parser::{CenterPoint, Polarity},
|
||||
command_parser::CenterPoint,
|
||||
};
|
||||
|
||||
const R_INNER: f64 = 2.0 * 5100.0;
|
||||
@ -37,7 +37,6 @@ pub struct ChannelState {
|
||||
pub pid_engaged: bool,
|
||||
pub pid: pid::Controller,
|
||||
pub sh: sh::Parameters,
|
||||
pub polarity: Polarity,
|
||||
}
|
||||
|
||||
impl ChannelState {
|
||||
@ -59,7 +58,6 @@ impl ChannelState {
|
||||
pid_engaged: false,
|
||||
pid: pid::Controller::new(pid::Parameters::default()),
|
||||
sh: sh::Parameters::default(),
|
||||
polarity: Polarity::Normal,
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
@ -17,7 +17,7 @@ use crate::{
|
||||
ad7172,
|
||||
channel::{Channel, Channel0, Channel1},
|
||||
channel_state::ChannelState,
|
||||
command_parser::{CenterPoint, PwmPin, Polarity},
|
||||
command_parser::{CenterPoint, PwmPin},
|
||||
command_handler::JsonBuffer,
|
||||
pins::{self, Channel0VRef, Channel1VRef},
|
||||
steinhart_hart,
|
||||
@ -158,11 +158,6 @@ impl Channels {
|
||||
|
||||
pub fn set_i(&mut self, channel: usize, i_set: ElectricCurrent) -> ElectricCurrent {
|
||||
let i_set = i_set.min(MAX_TEC_I).max(-MAX_TEC_I);
|
||||
self.channel_state(channel).i_set = i_set;
|
||||
let negate = match self.channel_state(channel).polarity {
|
||||
Polarity::Normal => 1.0,
|
||||
Polarity::Reversed => -1.0,
|
||||
};
|
||||
let vref_meas = match channel.into() {
|
||||
0 => self.channel0.vref_meas,
|
||||
1 => self.channel1.vref_meas,
|
||||
@ -170,9 +165,10 @@ impl Channels {
|
||||
};
|
||||
let center_point = vref_meas;
|
||||
let r_sense = ElectricalResistance::new::<ohm>(R_SENSE);
|
||||
let voltage = negate * i_set * 10.0 * r_sense + center_point;
|
||||
let voltage = i_set * 10.0 * r_sense + center_point;
|
||||
let voltage = self.set_dac(channel, voltage);
|
||||
let i_set = negate * (voltage - center_point) / (10.0 * r_sense);
|
||||
let i_set = (voltage - center_point) / (10.0 * r_sense);
|
||||
self.channel_state(channel).i_set = i_set;
|
||||
i_set
|
||||
}
|
||||
|
||||
@ -371,11 +367,7 @@ impl Channels {
|
||||
|
||||
// Get current passing through TEC
|
||||
pub fn get_tec_i(&mut self, channel: usize) -> ElectricCurrent {
|
||||
let tec_i = (self.adc_read(channel, PinsAdcReadTarget::ITec, 16) - self.adc_read(channel, PinsAdcReadTarget::VREF, 16)) / ElectricalResistance::new::<ohm>(0.4);
|
||||
match self.channel_state(channel).polarity {
|
||||
Polarity::Normal => tec_i,
|
||||
Polarity::Reversed => -tec_i,
|
||||
}
|
||||
(self.adc_read(channel, PinsAdcReadTarget::ITec, 16) - self.adc_read(channel, PinsAdcReadTarget::VREF, 16)) / ElectricalResistance::new::<ohm>(0.4)
|
||||
}
|
||||
|
||||
// Get voltage across TEC
|
||||
@ -423,10 +415,7 @@ impl Channels {
|
||||
let max = ElectricCurrent::new::<ampere>(3.0);
|
||||
let max_i_pos = max_i_pos.min(MAX_TEC_I).max(ElectricCurrent::zero());
|
||||
let duty = (max_i_pos / MAX_TEC_I_DUTY_TO_CURRENT_RATE).get::<ratio>();
|
||||
let duty = match self.channel_state(channel).polarity {
|
||||
Polarity::Normal => self.set_pwm(channel, PwmPin::MaxIPos, duty),
|
||||
Polarity::Reversed => self.set_pwm(channel, PwmPin::MaxINeg, duty),
|
||||
};
|
||||
let duty = self.set_pwm(channel, PwmPin::MaxIPos, duty);
|
||||
self.channel_state(channel).pwm_limits.max_i_pos = max_i_pos.get::<ampere>();
|
||||
(duty * MAX_TEC_I_DUTY_TO_CURRENT_RATE, max)
|
||||
}
|
||||
@ -435,27 +424,11 @@ impl Channels {
|
||||
let max = ElectricCurrent::new::<ampere>(3.0);
|
||||
let max_i_neg = max_i_neg.min(MAX_TEC_I).max(ElectricCurrent::zero());
|
||||
let duty = (max_i_neg / MAX_TEC_I_DUTY_TO_CURRENT_RATE).get::<ratio>();
|
||||
let duty = match self.channel_state(channel).polarity {
|
||||
Polarity::Normal => self.set_pwm(channel, PwmPin::MaxINeg, duty),
|
||||
Polarity::Reversed => self.set_pwm(channel, PwmPin::MaxIPos, duty),
|
||||
};
|
||||
let duty = self.set_pwm(channel, PwmPin::MaxINeg, duty);
|
||||
self.channel_state(channel).pwm_limits.max_i_neg = max_i_neg.get::<ampere>();
|
||||
(duty * MAX_TEC_I_DUTY_TO_CURRENT_RATE, max)
|
||||
}
|
||||
|
||||
pub fn set_polarity(&mut self, channel: usize, polarity: Polarity) {
|
||||
if self.channel_state(channel).polarity != polarity {
|
||||
let i_set = self.channel_state(channel).i_set;
|
||||
let max_i_pos = self.get_max_i_pos(channel);
|
||||
let max_i_neg = self.get_max_i_neg(channel);
|
||||
self.channel_state(channel).polarity = polarity;
|
||||
|
||||
self.set_i(channel, i_set);
|
||||
self.set_max_i_pos(channel, max_i_pos);
|
||||
self.set_max_i_neg(channel, max_i_neg);
|
||||
}
|
||||
}
|
||||
|
||||
fn report(&mut self, channel: usize) -> Report {
|
||||
let i_set = self.get_i(channel);
|
||||
let i_tec = self.adc_read(channel, PinsAdcReadTarget::ITec, 16);
|
||||
@ -515,7 +488,6 @@ impl Channels {
|
||||
max_v: self.get_max_v(channel),
|
||||
max_i_pos: self.get_max_i_pos(channel),
|
||||
max_i_neg: self.get_max_i_neg(channel),
|
||||
polarity: PolarityJson(self.channel_state(channel).polarity.clone()),
|
||||
}
|
||||
}
|
||||
|
||||
@ -597,21 +569,6 @@ impl Serialize for CenterPointJson {
|
||||
}
|
||||
}
|
||||
|
||||
pub struct PolarityJson(Polarity);
|
||||
|
||||
// used in JSON encoding, not for config
|
||||
impl Serialize for PolarityJson {
|
||||
fn serialize<S>(&self, serializer: S) -> Result<S::Ok, S::Error>
|
||||
where
|
||||
S: Serializer,
|
||||
{
|
||||
serializer.serialize_str(match self.0 {
|
||||
Polarity::Normal => "normal",
|
||||
Polarity::Reversed => "reversed",
|
||||
})
|
||||
}
|
||||
}
|
||||
|
||||
#[derive(Serialize)]
|
||||
pub struct PwmSummary {
|
||||
channel: usize,
|
||||
@ -620,7 +577,6 @@ pub struct PwmSummary {
|
||||
max_v: ElectricPotential,
|
||||
max_i_pos: ElectricCurrent,
|
||||
max_i_neg: ElectricCurrent,
|
||||
polarity: PolarityJson,
|
||||
}
|
||||
|
||||
#[derive(Serialize)]
|
||||
|
||||
@ -11,8 +11,7 @@ use super::{
|
||||
CenterPoint,
|
||||
PidParameter,
|
||||
PwmPin,
|
||||
ShParameter,
|
||||
Polarity
|
||||
ShParameter
|
||||
},
|
||||
ad7172,
|
||||
CHANNEL_CONFIG_KEY,
|
||||
@ -171,12 +170,6 @@ impl Handler {
|
||||
Ok(Handler::Handled)
|
||||
}
|
||||
|
||||
fn set_polarity(socket: &mut TcpSocket, channels: &mut Channels, channel: usize, polarity: Polarity) -> Result<Handler, Error> {
|
||||
channels.set_polarity(channel, polarity);
|
||||
send_line(socket, b"{}");
|
||||
Ok(Handler::Handled)
|
||||
}
|
||||
|
||||
fn set_pwm (socket: &mut TcpSocket, channels: &mut Channels, channel: usize, pin: PwmPin, value: f64) -> Result<Handler, Error> {
|
||||
match pin {
|
||||
PwmPin::ISet => {
|
||||
@ -418,7 +411,6 @@ impl Handler {
|
||||
Command::Show(ShowCommand::PostFilter) => Handler::show_post_filter(socket, channels),
|
||||
Command::Show(ShowCommand::Ipv4) => Handler::show_ipv4(socket, ipv4_config),
|
||||
Command::PwmPid { channel } => Handler::engage_pid(socket, channels, channel),
|
||||
Command::PwmPolarity { channel, polarity } => Handler::set_polarity(socket, channels, channel, polarity),
|
||||
Command::Pwm { channel, pin, value } => Handler::set_pwm(socket, channels, channel, pin, value),
|
||||
Command::CenterPoint { channel, center } => Handler::set_center_point(socket, channels, channel, center),
|
||||
Command::Pid { channel, parameter, value } => Handler::set_pid(socket, channels, channel, parameter, value),
|
||||
|
||||
@ -135,12 +135,6 @@ pub enum CenterPoint {
|
||||
Override(f32),
|
||||
}
|
||||
|
||||
#[derive(Debug, Clone, PartialEq, Serialize, Deserialize)]
|
||||
pub enum Polarity {
|
||||
Normal,
|
||||
Reversed,
|
||||
}
|
||||
|
||||
#[derive(Debug, Clone, PartialEq)]
|
||||
pub enum Command {
|
||||
Quit,
|
||||
@ -163,10 +157,6 @@ pub enum Command {
|
||||
PwmPid {
|
||||
channel: usize,
|
||||
},
|
||||
PwmPolarity {
|
||||
channel: usize,
|
||||
polarity: Polarity,
|
||||
},
|
||||
CenterPoint {
|
||||
channel: usize,
|
||||
center: CenterPoint,
|
||||
@ -307,18 +297,6 @@ fn pwm_pid(input: &[u8]) -> IResult<&[u8], ()> {
|
||||
value((), tag("pid"))(input)
|
||||
}
|
||||
|
||||
fn pwm_polarity(input: &[u8]) -> IResult<&[u8], Polarity> {
|
||||
preceded(
|
||||
tag("polarity"),
|
||||
preceded(
|
||||
whitespace,
|
||||
alt((value(Polarity::Normal, tag("normal")),
|
||||
value(Polarity::Reversed, tag("reversed"))
|
||||
))
|
||||
)
|
||||
)(input)
|
||||
}
|
||||
|
||||
fn pwm(input: &[u8]) -> IResult<&[u8], Result<Command, Error>> {
|
||||
let (input, _) = tag("pwm")(input)?;
|
||||
alt((
|
||||
@ -331,10 +309,6 @@ fn pwm(input: &[u8]) -> IResult<&[u8], Result<Command, Error>> {
|
||||
let (input, ()) = pwm_pid(input)?;
|
||||
Ok((input, Ok(Command::PwmPid { channel })))
|
||||
},
|
||||
|input| {
|
||||
let (input, polarity) = pwm_polarity(input)?;
|
||||
Ok((input, Ok(Command::PwmPolarity { channel, polarity })))
|
||||
},
|
||||
|input| {
|
||||
let (input, config) = pwm_setup(input)?;
|
||||
match config {
|
||||
|
||||
@ -8,7 +8,7 @@ use uom::si::{
|
||||
use crate::{
|
||||
ad7172::PostFilter,
|
||||
channels::Channels,
|
||||
command_parser::{CenterPoint, Polarity},
|
||||
command_parser::CenterPoint,
|
||||
pid,
|
||||
steinhart_hart,
|
||||
};
|
||||
@ -20,7 +20,6 @@ pub struct ChannelConfig {
|
||||
pid_target: f32,
|
||||
pid_engaged: bool,
|
||||
i_set: ElectricCurrent,
|
||||
polarity: Polarity,
|
||||
sh: steinhart_hart::Parameters,
|
||||
pwm: PwmLimits,
|
||||
/// uses variant `PostFilter::Invalid` instead of `None` to save space
|
||||
@ -46,8 +45,7 @@ impl ChannelConfig {
|
||||
pid: state.pid.parameters.clone(),
|
||||
pid_target: state.pid.target as f32,
|
||||
pid_engaged: state.pid_engaged,
|
||||
i_set,
|
||||
polarity: state.polarity.clone(),
|
||||
i_set: i_set,
|
||||
sh: state.sh.clone(),
|
||||
pwm,
|
||||
adc_postfilter,
|
||||
@ -70,7 +68,6 @@ impl ChannelConfig {
|
||||
};
|
||||
let _ = channels.adc.set_postfilter(channel as u8, adc_postfilter);
|
||||
let _ = channels.set_i(channel, self.i_set);
|
||||
channels.set_polarity(channel, self.polarity.clone());
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user