forked from M-Labs/thermostat
Compare commits
4 Commits
6b5c5340f8
...
1741acfc3b
| Author | SHA1 | Date | |
|---|---|---|---|
| 1741acfc3b | |||
| ce4fb6090a | |||
| f3d5b1dc6b | |||
| ca096c119d |
31
README.md
31
README.md
@ -256,22 +256,21 @@ Use the bare `report` command to obtain a single report. Enable
|
||||
continuous reporting with `report mode on`. Reports are JSON objects
|
||||
with the following keys.
|
||||
|
||||
| Key | Unit | Description |
|
||||
| --- | :---: | --- |
|
||||
| `channel` | Integer | Channel `0`, or `1` |
|
||||
| `time` | Seconds | Temperature measurement time |
|
||||
| `adc` | Volts | AD7172 input |
|
||||
| `sens` | Ohms | Thermistor resistance derived from `adc` |
|
||||
| `temperature` | Degrees Celsius | Steinhart-Hart conversion result derived from `sens` |
|
||||
| `pid_engaged` | Boolean | `true` if in closed-loop mode |
|
||||
| `current_swapped` | Boolean | `true` if TEC current direction is swapped relative to front panel |
|
||||
| `i_set` | Amperes | TEC output current |
|
||||
| `dac_value` | Volts | AD5680 output derived from `i_set` |
|
||||
| `dac_feedback` | Volts | ADC measurement of the AD5680 output |
|
||||
| `i_tec` | Volts | MAX1968 TEC current monitor |
|
||||
| `tec_i` | Amperes | TEC output current feedback derived from `i_tec` |
|
||||
| `tec_u_meas` | Volts | Measurement of the voltage across the TEC |
|
||||
| `pid_output` | Amperes | PID control output |
|
||||
| Key | Unit | Description |
|
||||
| --- | :---: | --- |
|
||||
| `channel` | Integer | Channel `0`, or `1` |
|
||||
| `time` | Seconds | Temperature measurement time |
|
||||
| `adc` | Volts | AD7172 input |
|
||||
| `sens` | Ohms | Thermistor resistance derived from `adc` |
|
||||
| `temperature` | Degrees Celsius | Steinhart-Hart conversion result derived from `sens` |
|
||||
| `pid_engaged` | Boolean | `true` if in closed-loop mode |
|
||||
| `i_set` | Amperes | TEC output current |
|
||||
| `dac_value` | Volts | AD5680 output derived from `i_set` |
|
||||
| `dac_feedback` | Volts | ADC measurement of the AD5680 output |
|
||||
| `i_tec` | Volts | MAX1968 TEC current monitor |
|
||||
| `tec_i` | Amperes | TEC output current feedback derived from `i_tec` |
|
||||
| `tec_u_meas` | Volts | Measurement of the voltage across the TEC |
|
||||
| `pid_output` | Amperes | PID control output |
|
||||
|
||||
Note: With Thermostat v2 and below, the voltage and current readouts `i_tec` and `tec_i` are noisy without the hardware fix shown in [this PR][https://git.m-labs.hk/M-Labs/thermostat/pulls/105].
|
||||
|
||||
|
||||
@ -157,13 +157,11 @@ impl Channels {
|
||||
}
|
||||
|
||||
pub fn set_i(&mut self, channel: usize, i_set: ElectricCurrent) -> ElectricCurrent {
|
||||
let i_set = i_set.min(MAX_TEC_I).max(-MAX_TEC_I);
|
||||
let mut i_set = i_set.min(MAX_TEC_I).max(-MAX_TEC_I);
|
||||
self.channel_state(channel).i_set = i_set;
|
||||
let negate = if self.channel_state(channel).polarity_swapped {
|
||||
-1.0
|
||||
} else {
|
||||
1.0
|
||||
};
|
||||
if self.channel_state(channel).polarity_swapped {
|
||||
i_set = -i_set;
|
||||
}
|
||||
let vref_meas = match channel.into() {
|
||||
0 => self.channel0.vref_meas,
|
||||
1 => self.channel1.vref_meas,
|
||||
@ -171,9 +169,9 @@ impl Channels {
|
||||
};
|
||||
let center_point = vref_meas;
|
||||
let r_sense = ElectricalResistance::new::<ohm>(R_SENSE);
|
||||
let voltage = negate * i_set * 10.0 * r_sense + center_point;
|
||||
let voltage = i_set * 10.0 * r_sense + center_point;
|
||||
let voltage = self.set_dac(channel, voltage);
|
||||
let i_set = negate * (voltage - center_point) / (10.0 * r_sense);
|
||||
let i_set = (voltage - center_point) / (10.0 * r_sense);
|
||||
i_set
|
||||
}
|
||||
|
||||
@ -479,19 +477,6 @@ impl Channels {
|
||||
(duty * MAX_TEC_I_DUTY_TO_CURRENT_RATE, max)
|
||||
}
|
||||
|
||||
pub fn swap_polarity(&mut self, channel: usize, swapped: bool) {
|
||||
if self.channel_state(channel).polarity_swapped != swapped {
|
||||
let i_set = self.channel_state(channel).i_set;
|
||||
let max_i_pos = self.get_max_i_pos(channel).0;
|
||||
let max_i_neg = self.get_max_i_neg(channel).0;
|
||||
|
||||
self.channel_state(channel).polarity_swapped = swapped;
|
||||
self.set_i(channel, i_set);
|
||||
self.set_max_i_pos(channel, max_i_pos);
|
||||
self.set_max_i_neg(channel, max_i_neg);
|
||||
}
|
||||
}
|
||||
|
||||
fn report(&mut self, channel: usize) -> Report {
|
||||
let i_set = self.get_i(channel);
|
||||
let i_tec = self.adc_read(channel, PinsAdcReadTarget::ITec, 16);
|
||||
|
||||
@ -182,7 +182,10 @@ impl Handler {
|
||||
}
|
||||
|
||||
fn swap_polarity (socket: &mut TcpSocket, channels: &mut Channels, channel: usize, swapped: bool) -> Result<Handler, Error> {
|
||||
channels.swap_polarity(channel, swapped);
|
||||
channels.channel_state(channel).polarity_swapped = swapped;
|
||||
let channel_state = channels.channel_state(channel);
|
||||
let i_set = channel_state.i_set;
|
||||
channels.set_i(channel, i_set);
|
||||
send_line(socket, b"{}");
|
||||
Ok(Handler::Handled)
|
||||
}
|
||||
|
||||
@ -20,7 +20,6 @@ pub struct ChannelConfig {
|
||||
pid_target: f32,
|
||||
pid_engaged: bool,
|
||||
i_set: ElectricCurrent,
|
||||
polarity_swapped: bool,
|
||||
sh: steinhart_hart::Parameters,
|
||||
pwm: PwmLimits,
|
||||
/// uses variant `PostFilter::Invalid` instead of `None` to save space
|
||||
@ -46,8 +45,7 @@ impl ChannelConfig {
|
||||
pid: state.pid.parameters.clone(),
|
||||
pid_target: state.pid.target as f32,
|
||||
pid_engaged: state.pid_engaged,
|
||||
i_set,
|
||||
polarity_swapped: state.polarity_swapped,
|
||||
i_set: i_set,
|
||||
sh: state.sh.clone(),
|
||||
pwm,
|
||||
adc_postfilter,
|
||||
@ -70,7 +68,6 @@ impl ChannelConfig {
|
||||
};
|
||||
let _ = channels.adc.set_postfilter(channel as u8, adc_postfilter);
|
||||
let _ = channels.set_i(channel, self.i_set);
|
||||
channels.swap_polarity(channel, self.polarity_swapped);
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user