From 9061b175a721a10b24a311a8e43ae318f65c9e69 Mon Sep 17 00:00:00 2001 From: atse Date: Fri, 16 Aug 2024 17:43:14 +0800 Subject: [PATCH] README: swap_polarity --- README.md | 73 ++++++++++++++++++++++++++++--------------------------- 1 file changed, 37 insertions(+), 36 deletions(-) diff --git a/README.md b/README.md index bf6cff8..7d12c29 100644 --- a/README.md +++ b/README.md @@ -94,42 +94,43 @@ The scope of this setting is per TCP session. Send commands as simple text string terminated by `\n`. Responses are formatted as line-delimited JSON. -| Syntax | Function | -|----------------------------------|-------------------------------------------------------------------------------| -| `report` | Show current input | -| `report mode` | Show current report mode | -| `report mode ` | Set report mode | -| `pwm` | Show current PWM settings | -| `pwm <0/1> max_i_pos ` | Set maximum positive output current | -| `pwm <0/1> max_i_neg ` | Set maximum negative output current | -| `pwm <0/1> max_v ` | Set maximum output voltage | -| `pwm <0/1> i_set ` | Disengage PID, set fixed output current | -| `pwm <0/1> pid` | Let output current to be controlled by the PID | -| `center <0/1> ` | Set the MAX1968 0A-centerpoint to the specified fixed voltage | -| `center <0/1> vref` | Set the MAX1968 0A-centerpoint to measure from VREF | -| `pid` | Show PID configuration | -| `pid <0/1> target ` | Set the PID controller target temperature | -| `pid <0/1> kp ` | Set proportional gain | -| `pid <0/1> ki ` | Set integral gain | -| `pid <0/1> kd ` | Set differential gain | -| `pid <0/1> output_min ` | Set mininum output | -| `pid <0/1> output_max ` | Set maximum output | -| `s-h` | Show Steinhart-Hart equation parameters | -| `s-h <0/1> ` | Set Steinhart-Hart parameter for a channel | -| `postfilter` | Show postfilter settings | -| `postfilter <0/1> off` | Disable postfilter | -| `postfilter <0/1> rate ` | Set postfilter output data rate | -| `load [0/1]` | Restore configuration for channel all/0/1 from flash | -| `save [0/1]` | Save configuration for channel all/0/1 to flash | -| `reset` | Reset the device | -| `dfu` | Reset device and enters USB device firmware update (DFU) mode | -| `ipv4 [Y.Y.Y.Y]` | Configure IPv4 address, netmask length, and optional default gateway | -| `fan` | Show current fan settings and sensors' measurements | -| `fan ` | Set fan power with values from 1 to 100 | -| `fan auto` | Enable automatic fan speed control | -| `fcurve ` | Set fan controller curve coefficients (see *Fan control* section) | -| `fcurve default` | Set fan controller curve coefficients to defaults (see *Fan control* section) | -| `hwrev` | Show hardware revision, and settings related to it | +| Syntax | Function | +|-------------------------------------------|-------------------------------------------------------------------------------| +| `report` | Show current input | +| `report mode` | Show current report mode | +| `report mode ` | Set report mode | +| `pwm` | Show current PWM settings | +| `pwm <0/1> max_i_pos ` | Set maximum positive output current | +| `pwm <0/1> max_i_neg ` | Set maximum negative output current | +| `pwm <0/1> max_v ` | Set maximum output voltage | +| `pwm <0/1> i_set ` | Disengage PID, set fixed output current | +| `pwm <0/1> polarity_swapped ` | Swap current polarity on channel | +| `pwm <0/1> pid` | Let output current to be controlled by the PID | +| `center <0/1> ` | Set the MAX1968 0A-centerpoint to the specified fixed voltage | +| `center <0/1> vref` | Set the MAX1968 0A-centerpoint to measure from VREF | +| `pid` | Show PID configuration | +| `pid <0/1> target ` | Set the PID controller target temperature | +| `pid <0/1> kp ` | Set proportional gain | +| `pid <0/1> ki ` | Set integral gain | +| `pid <0/1> kd ` | Set differential gain | +| `pid <0/1> output_min ` | Set mininum output | +| `pid <0/1> output_max ` | Set maximum output | +| `s-h` | Show Steinhart-Hart equation parameters | +| `s-h <0/1> ` | Set Steinhart-Hart parameter for a channel | +| `postfilter` | Show postfilter settings | +| `postfilter <0/1> off` | Disable postfilter | +| `postfilter <0/1> rate ` | Set postfilter output data rate | +| `load [0/1]` | Restore configuration for channel all/0/1 from flash | +| `save [0/1]` | Save configuration for channel all/0/1 to flash | +| `reset` | Reset the device | +| `dfu` | Reset device and enters USB device firmware update (DFU) mode | +| `ipv4 [Y.Y.Y.Y]` | Configure IPv4 address, netmask length, and optional default gateway | +| `fan` | Show current fan settings and sensors' measurements | +| `fan ` | Set fan power with values from 1 to 100 | +| `fan auto` | Enable automatic fan speed control | +| `fcurve ` | Set fan controller curve coefficients (see *Fan control* section) | +| `fcurve default` | Set fan controller curve coefficients to defaults (see *Fan control* section) | +| `hwrev` | Show hardware revision, and settings related to it | ## USB