4456 -> 4456-4457: add almazny

4456-4457.tex

@@ -1,10 +1,10 @@
 \input{preamble.tex}
-\graphicspath{{images/4456}{images}}
+\graphicspath{{images/4456-4457}{images}}
 
-\title{4456 Synthesizer Mirny}
+\title{4456 Synthesizer Mirny / 4457 HF Synthesizer Mirny + Almazny}
 \author{M-Labs Limited}
-\date{January 2022}
-\revision{Revision 1}
+\date{January 2025}
+\revision{Revision 2}
 \companylogo{\includegraphics[height=0.73in]{artiq_sinara.pdf}}
 
 \begin{document}
@@ -13,29 +13,28 @@
 \section{Features}
 
 \begin{itemize}
-\item{4-channel VCO/PLL}
-\item{Output frequency ranges from 53 MHz to \textgreater 4 GHz}
-\item{Up to 13.6 GHz with Almazny mezzanine}
-\item{Higher frequency resolution than Urukul}
-\item{Lower jitter and phase noise}
-\item{Large frequency changes take several milliseconds}
+    \item{4-channel VCO/PLL}
+    \item{Output frequency ranges from 53 MHz to \textgreater 4 GHz for 4456 Mirny only}
+    \item{Up to 13.6 GHz with 4457 mezzanine Almazny}
+    \item{Higher frequency resolution than Urukul}
+    \item{Lower jitter and phase noise}
+    \item{Large frequency changes take several milliseconds}
 \end{itemize}
 
 \section{Applications}
 
 \begin{itemize}
-\item{Low-noise microwave source}
-\item{Quantum state control}
-\item{Driving acousto/electro-optic modulators}
+    \item{Low-noise microwave source}
+    \item{Quantum state control}
+    \item{Driving acousto/electro-optic modulators}
 \end{itemize}
 
 \section{General Description}
-The 4456 Synthesizer Mirny card is a 4hp EEM module, part of the ARTIQ/Sinara family. It adds microwave generation capabilities to carrier cards such as 1124 Kasli and 1125 Kasli-SoC.
+    The 4456 Synthesizer Mirny card is a 4hp EEM module; the 4457 HF Synthesizer Mirny + Almazny card, consisting of 4456 Mirny plus the 4-channel Almazny HF mezzanine, is a 8hp EEM module. Both Synthesizer cards add microwave generation capabilities to carrier cards such as 1124 Kasli and 1125 Kasli-SoC.
 
-It provides 4 channels of PLL frequency synthesis. Output frequencies from 53 MHz to \textgreater 4 GHz are supported.The range can be expanded up to 13.6 GHz with the Almazny mezzanine (4467 HF Synthesizer).
-
-Each channel can be attenuated from 0 to -31.5 dB by a digital attenuator. RF switches on each channel provides at least 50 dB isolation.
+    Both cards provide 4 channels of PLL frequency synthesis. 4456 Synthesizer Mirny supports output frequencies from 53 MHz to \textgreater 4GHz. As 4457 HF Synthesizer with Almazny mezzanine this range is expanded up to 13.6 GHz.
 
+    Each channel can be attenuated from 0 to -31.5 dB by a digital attenuator. RF switches on each channel provide at least 50 dB isolation.
 
 % Switch to next column
 \vfill\break
@@ -275,30 +274,44 @@ Each channel can be attenuated from 0 to -31.5 dB by a digital attenuator. RF sw
 
 \begin{figure}[hbt!]
     \centering
-    \includegraphics[height=2in]{photo4456.jpg}
-    \includegraphics[height=3in, angle=90]{Mirny_FP.pdf}
-    \caption{Mirny card and front panel}
+    \includegraphics[height=2in]{photo4457.jpg}
+    \caption{Mirny + Almazny card}
 \end{figure}
 
 % For wide tables, a single column layout is better. It can be switched
 % page-by-page.
 \onecolumn
 
-\sourcesection{4456 Synthesizer Mirny}{https://github.com/sinara-hw/mirny}
+\begin{figure}[hbt!]
+    \subfloat[\centering Mirny and Almazny front panels]{{
+        \begin{minipage}[b]{0.5\linewidth}
+            \centering
+            \includegraphics[height=3in, angle=90]{fp4456.pdf} \\
+            \vspace{0.2in}
+            \includegraphics[height=3in, angle=90]{fp4457.pdf}
+            \vspace{0.25in}
+        \end{minipage}
+    }}
+    \subfloat[\centering Mirny, top-down view]{{
+        \includegraphics[height=2.5in]{photo4456.jpg}
+    }}
+\end{figure}
+
+\sourcesectiond{4456 Synthesizer Mirny}{the 4457 Almazny mezzanine}{https://github.com/sinara-hw/mirny}{https://github.com/sinara-hw/Almazny}
 
 \section{Electrical Specifications}
 
-Specifications of parameters are based on the datasheets of the PLL IC
-(ADF5356\footnote{\label{adf5356}\url{https://www.analog.com/media/en/technical-documentation/data-sheets/ADF5356.pdf}}),
-clock buffer IC (Si53340-B-GM\footnote{\label{clock_buffer}\url{https://www.skyworksinc.com/-/media/Skyworks/SL/documents/public/data-sheets/si5334x-datasheet.pdf}}),
-and digital attenuator IC (HMC542BLP4E\footnote{\label{attenuator}\url{https://www.analog.com/media/en/technical-documentation/data-sheets/hmc542b.pdf}}).
-Test results are from Krzysztof Belewicz's thesis. "Microwave synthesizer for driving ion traps in quantum computing"\footnote{\label{mirny_thesis}\url{https://m-labs.hk/Krzysztof\_Belewicz\_V1.1.pdf}}.
+    Specifications of parameters are based on the datasheets of the PLL IC
+    (ADF5356\footnote{\label{adf5356}\url{https://www.analog.com/media/en/technical-documentation/data-sheets/ADF5356.pdf}}),
+    clock buffer IC (Si53340-B-GM\footnote{\label{clock_buffer}\url{https://www.skyworksinc.com/-/media/Skyworks/SL/documents/public/data-sheets/si5334x-datasheet.pdf}}),
+    and digital attenuator IC (HMC542BLP4E\footnote{\label{attenuator}\url{https://www.analog.com/media/en/technical-documentation/data-sheets/hmc542b.pdf}}).
+    Test results are from Krzysztof Belewicz's thesis. "Microwave synthesizer for driving ion traps in quantum computing"\footnote{\label{mirny_thesis}\url{https://m-labs.hk/Krzysztof\_Belewicz\_V1.1.pdf}}.
 
-\begin{table}[h]
-\centering
-\begin{threeparttable}
-\caption{Recommended Operating Conditions}
-\begin{tabularx}{0.9\textwidth}{l | c c c | c | X}
+    \begin{table}[h]
+    \centering
+    \begin{threeparttable}
+    \caption{Recommended Operating Conditions}
+    \begin{tabularx}{0.9\textwidth}{l | c c c | c | X}
         \thickhline
         \textbf{Parameter} & \textbf{Min.} & \textbf{Typ.} & \textbf{Max.} &
         \textbf{Unit} & \textbf{Conditions} \\
@@ -313,57 +326,73 @@ Test results are from Krzysztof Belewicz's thesis. "Microwave synthesizer for dr
             \hspace{3mm}Differential input swing\repeatfootnote{clock_buffer}
                 & 0.11 & & 1.55 & V\textsubscript{p-p} & \\
         \thickhline
-\end{tabularx}
-\end{threeparttable}
-\end{table}
+    \end{tabularx}
+    \end{threeparttable}
+    \end{table}
 
-\begin{table}[h]
-\centering
-\begin{threeparttable}
-\caption{Output Specifications}
-\begin{tabularx}{0.9\textwidth}{l | c c c | c | X}
+    \begin{table}[h]
+    \centering
+    \begin{threeparttable}
+    \caption{Output Specifications}
+    \begin{tabularx}{0.9\textwidth}{l | c c c | c | X}
         \thickhline
         \textbf{Parameter} & \textbf{Min.} & \textbf{Typ.} & \textbf{Max.} &
         \textbf{Unit} & \textbf{Conditions} \\
         \hline
-    Frequency & 53.125 &  & 4000 & MHz & \\
+        Frequency & 53.125 &  & 4000 & MHz & 4456 Mirny only \\
+        & &  & 13600 & MHz & With Almazny mezzanine \\
         \hline
         Digital attenuation\repeatfootnote{attenuator} & -31.5 & & 0 & dB & \\
         \hline
-    Resolution & \multicolumn{4}{c|}{} & \\
-    \hspace{3mm} Frequency\repeatfootnote{adf5356} & \multicolumn{4}{c|}{52 bits} & \\
-    \hspace{3mm} Phase offset\repeatfootnote{adf5356} & \multicolumn{4}{c|}{24 bits} & \\
-    \hspace{3mm} Digital attenuation\repeatfootnote{attenuator} & \multicolumn{4}{c|}{0.5 dB} & \\
-    \thickhline
-\end{tabularx}
-\end{threeparttable}
-\end{table}
+    \end{tabularx}
+    \end{threeparttable}
+    \end{table}
 
 \newpage
 
-Phase noise performance of Mirny was tested using the ADF4351 evaluation kit\repeatfootnote{mirny_thesis}. The SPI signal was driven by the evaluation kit, converted into LVDS signal by propagating through the DIO-tester card, finally arriving at the Mirny card. Mirny was then connected to the RSA5100A spectrum analyzer for measurement.
+\begin{table}[h]
+    \centering
+    \begin{threeparttable}
+    \caption{Output Specifications, cont.}
+    \begin{tabularx}{0.9\textwidth}{l | c c c | c | X}
+        \thickhline
+        \textbf{Parameter} & \textbf{Min.} & \textbf{Typ.} & \textbf{Max.} &
+        \textbf{Unit} & \textbf{Conditions} \\
+        Resolution & & & & \\
+        \hspace{3mm} Frequency\repeatfootnote{adf5356} & \multicolumn{3}{c|}{52} & bits & \\
+        \hspace{3mm} Phase offset\repeatfootnote{adf5356} & \multicolumn{3}{c|}{24} & bits & \\
+        \hspace{3mm} Digital attenuation\repeatfootnote{attenuator} & \multicolumn{3}{c|}{0.5} & dB & \\
+        \thickhline
+    \end{tabularx}
+    \end{threeparttable}
+    \end{table}
 
-Noise response spike can be improved by inserting an additional common-mode choke between the power supply and Mirny; note that this common-mode choke is not present on the card itself. The following is a comparison between the two setups at 1 GHz output:
-\begin{itemize}
-    \item Red: Before any modifications
-    \item Blue: CM choke added with an 100 \textmu F capacitor after the CM choke
-\end{itemize}
+    Phase noise performance of 4456 Mirny was tested using the ADF4351 evaluation kit\repeatfootnote{mirny_thesis}. The SPI signal was driven by the evaluation kit, converted into LVDS signal by propagating through the DIO-tester card, finally arriving at the Mirny card. 4456 Mirny was then connected to the RSA5100A spectrum analyzer for measurement.
 
-\begin{figure}[H]
+    Noise response spike can be improved by inserting an additional common-mode choke between the power supply and Mirny; note that this common-mode choke is not present on the card itself. The following is a comparison between the two setups at 1 GHz output:
+
+    \begin{figure}[H]
         \centering
         \includegraphics[height=3in]{mirny_phase_noise_cm_choke.png}
         \caption{Phase noise measurement at 1 GHz}
-\end{figure}
+    \end{figure}
 
-Phase noise at different output frequencies is then measured:
+    \begin{itemize}
+        \item Red: Before any modifications
+        \item Blue: CM choke added with an 100 \textmu F capacitor after the CM choke
+    \end{itemize}
 
-\newcolumntype{Y}{>{\centering\arraybackslash}X}
+\newpage
 
-\begin{table}[hbt!]
-\centering
-\begin{threeparttable}
-\caption{Phase noise performance}
-\begin{tabularx}{0.8\textwidth}{| c | Y | Y | Y | Y | Y |}
+    Phase noise at different output frequencies is then measured:
+
+    \newcolumntype{Y}{>{\centering\arraybackslash}X}
+
+    \begin{table}[hbt!]
+    \centering
+    \begin{threeparttable}
+    \caption{Phase noise performance}
+    \begin{tabularx}{0.8\textwidth}{| c | Y | Y | Y | Y | Y |}
         \thickhline
         \multirow{2}{*}{\textbf{Output frequency}} &
         \multicolumn{5}{c|}{\textbf{Phase noise (dBc/Hz) at carrier offset}}\\
@@ -379,33 +408,61 @@ Phase noise at different output frequencies is then measured:
         \hline
         3.5 GHz & -96 & -101 & -103 & -127 & -128 \\
         \thickhline
-\end{tabularx}
-\end{threeparttable}
-\end{table}
+    \end{tabularx}
+    \end{threeparttable}
+    \end{table}
 
-\newpage
-
-\begin{figure}[H]
+    \begin{figure}[H]
         \centering
         \includegraphics[height=3in]{mirny_phase_noise_frequency.png}
         \caption{Phase noise measurement}
-\end{figure}
+    \end{figure}
+
+\newpage
+\sysdescsection
+
+    4456 Synthesizer Mirny must be entered in the \texttt{peripherals} list of the corresponding core device in the following format:
+
+    \begin{tcolorbox}[colback=white]
+        \begin{minted}{json}
+            {
+                "type": "mirny",
+                "ports": 0,
+                "clk_sel": "mmcx", // optional
+                "refclk": 125e6 // optional
+            }
+        \end{minted}
+    \end{tcolorbox}
+
+    Replace 0 with the EEM port number used on the core device. Any port can be used. The \texttt{clk\_sel} field is optional and may be specified as one of either \texttt{xo}, \texttt{mmcx}, or \texttt{sma}. The default is \texttt{xo}. The \texttt{refclk} field is optional and the default is \texttt{100e6}.
+
+    For 4457 Mirny + Almazny, one field must be added:
+
+    \begin{tcolorbox}[colback=white]
+        \begin{minted}{json}
+            {
+                "type": "mirny",
+                "almazny": true,
+                "ports": 0
+            }
+        \end{minted}
+    \end{tcolorbox}
 
 \codesection{4456 Synthesizer Mirny}
 
-\subsection{1 GHz sinusoidal wave}
-Generates a 1 GHz sinusoid from RF0 with full scale amplitude, attenuated by 12 dB. Both the CPLD and the PLL channels should be initialized.
+    \subsection{1 GHz sinusoidal wave}
+    Generates a 1 GHz sinusoid from RF0 with full scale amplitude, attenuated by 12 dB. Both the CPLD and the PLL channels should be initialized.
 
-\inputcolorboxminted{firstline=10,lastline=17}{examples/pll.py}
+    \inputcolorboxminted{firstline=10,lastline=17}{examples/pll.py}
 
-\subsection{ADF5356 power control}
-Output power can be controlled be configuring the PLL channels individually in addition to the digital attenuators. After initialization of the PLL channel (ADF5356), the following line of code can change the output power level:
+    \subsection{ADF5356 power control}
+    Output power can be controlled be configuring the PLL channels individually in addition to the digital attenuators. After initialization of the PLL channel (ADF5356), the following line of code can change the output power level:
 
-\inputcolorboxminted{firstline=28,lastline=28}{examples/pll.py}
+    \inputcolorboxminted{firstline=28,lastline=28}{examples/pll.py}
 
-The parameter corresponds to a specific change of output power according to the following table\repeatfootnote{adf5356}.
+    The parameter corresponds to a specific change of output power according to the following table\repeatfootnote{adf5356}.
 
-\begin{center}
+    \begin{center}
         \captionof{table}{Power changes from ADF5356}
         \begin{tabular}{|c|c|}
         \hline
@@ -415,18 +472,18 @@ The parameter corresponds to a specific change of output power according to the
         2 & +2 dBm \\ \hline
         3 & +5 dBm \\ \hline
         \end{tabular}
-\end{center}
+    \end{center}
 
-ADF5356 gives +5 dBm by default. The stored parameter in ADF5356 can be read using the following line"
+    ADF5356 gives +5 dBm by default. The stored parameter in ADF5356 can be read using the following line"
 
-\inputcolorboxminted{firstline=29,lastline=29}{examples/pll.py}
+    \inputcolorboxminted{firstline=29,lastline=29}{examples/pll.py}
 
-\subsection{Periodic 100\textmu s pulses}
-The output can be toggled on and off periodically using the RF switches. The following code emits a 100\textmu s pulse in every millisecond. A microwave signal should be programmed in prior (such as the 1 GHz wave example).
+    \subsection{Periodic 100\textmu s pulses}
+    The output can be toggled on and off periodically using the RF switches. The following code emits a 100\textmu s pulse in every millisecond. A microwave signal should be programmed in prior (such as the 1 GHz wave example).
 
-\inputcolorboxminted{firstline=42,lastline=44}{examples/pll.py}
+    \inputcolorboxminted{firstline=42,lastline=44}{examples/pll.py}
 
-\ordersection{4456 Synthesizer Mirny}
+\ordersection{4456 Synthesizer Mirny or 4457 HF Synthesizer Mirny + Almazny}
 
 \finalfootnote