Firmware for the Sinara 8451 Thermostat

Go to file

Astro d40a038c2f config: switch to postcard encoding		2020-09-24 02:06:53 +02:00
.cargo	use NixOS 19.03 multiarch gdb instead of custom build	2019-04-12 17:14:38 +08:00
src	config: switch to postcard encoding	2020-09-24 02:06:53 +02:00
.gitignore	create nix build infrastructure	2019-03-07 16:27:33 +01:00
Cargo.lock	config: switch to postcard encoding	2020-09-24 02:06:53 +02:00
Cargo.toml	config: switch to postcard encoding	2020-09-24 02:06:53 +02:00
LICENSE	LICENSE: add GPL-3	2019-03-18 21:47:18 +01:00
README.md	command_parser: parse load/save	2020-09-24 01:17:50 +02:00
build.rs	create nix build infrastructure	2019-03-07 16:27:33 +01:00
cargosha256.nix	implement mac address generation with reading eui48 from i2c eeprom	2020-09-24 00:19:07 +02:00
memory.x	memory.x: fix RAM2 region, place stack in CCMRAM	2019-03-12 22:52:52 +01:00
openocd.gdb	gdb with `cargo run`	2019-03-19 17:16:45 +01:00

README.md

Firmware for the Sinara 8451 Thermostat

Building

Debian-based systems (tested on Ubuntu 19.10)

install git, clone this repository
install rustup

rustup toolchain install nightly
rustup update
rustup target add thumbv7em-none-eabihf --toolchain nightly
rustup default nightly
cargo build --release

The resulting ELF file will be located under target/thumbv7em-none-eabihf/release/thermostat

Network

Connecting

Ethernet, IP: 192.168.1.26/24

Use netcat to connect to port 23/tcp (telnet)

nc -vv 192.168.1.26 23

telnet clients send binary data after connect. Enter \n once to invalidate the first line of input.

Reading ADC input

Set report mode to on for a continuous stream of input data.

The scope of this setting is per TCP session.

Commands

Syntax	Function
`report`	Show current input
`report mode`	Show current report mode
`report mode <off/on>`	Set report mode
`pwm`	Show current PWM settings
`pwm <0/1> max_i_pos <ratio>`	Set PWM duty cycle for max_i_pos to ampere
`pwm <0/1> max_i_neg <ratio>`	Set PWM duty cycle for max_i_neg to ampere
`pwm <0/1> max_v <ratio>`	Set PWM duty cycle for max_v to volt
`pwm <0/1> <volts>`	Disengage PID, set i_set DAC to ampere
`pwm <0/1> pid`	Set PWM to be controlled by PID
`center <0/1> <volts>`	Set the MAX1968 0A-centerpoint to volts
`center <0/1> vref`	Set the MAX1968 0A-centerpoint to measure from VREF
`pid`	Show PID configuration
`pid <0/1> target <value>`	Set the PID controller target
`pid <0/1> kp <value>`	Set proportional gain
`pid <0/1> ki <value>`	Set integral gain
`pid <0/1> kd <value>`	Set differential gain
`pid <0/1> output_min <value>`	Set mininum output
`pid <0/1> output_max <value>`	Set maximum output
`pid <0/1> integral_min <value>`	Set integral lower bound
`pid <0/1> integral_max <value>`	Set integral upper bound
`s-h`	Show Steinhart-Hart equation parameters
`s-h <0/1> <t/b/r0> <value>`	Set Steinhart-Hart parameter for a channel
`postfilter <0/1> rate <rate>`	Set postfilter output data rate
`load`	Restore configuration from EEPROM
`save`	Save configuration to EEPROM