README.md

@@ -93,13 +93,16 @@ Send commands as simple text string terminated by `\n`. Responses are
 formatted as line-delimited JSON.
 
 | Syntax                                     | Function                                                                      |
-|----------------------------------|-------------------------------------------------------------------------------|
+|------------------------------------------- |-------------------------------------------------------------------------------|
 | `report`                                   | Show current input                                                            |
+| `report mode`                              | Show current report mode                                                      |
+| `report mode <off/on>`                     | Set report mode                                                               |
 | `pwm`                                      | Show current PWM settings                                                     |
 | `pwm <0/1> max_i_pos <amp>`                | Set maximum positive output current                                           |
 | `pwm <0/1> max_i_neg <amp>`                | Set maximum negative output current                                           |
 | `pwm <0/1> max_v <volt>`                   | Set maximum output voltage                                                    |
 | `pwm <0/1> i_set <amp>`                    | Disengage PID, set fixed output current                                       |
+| `pwm <0/1> polarity <normal/reversed>`     | Set output current polarity, with 'normal' being the front panel polarity     |
 | `pwm <0/1> pid`                            | Let output current to be controlled by the PID                                |
 | `center <0/1> <volt>`                      | Set the MAX1968 0A-centerpoint to the specified fixed voltage                 |
 | `center <0/1> vref`                        | Set the MAX1968 0A-centerpoint to measure from VREF                           |
@@ -182,6 +185,8 @@ postfilter rate can be tuned with the `postfilter` command.
 
 When using a TEC module with the Thermostat, the Thermostat expects the thermal load (where the thermistor is located) to cool down with a positive software current set point, and heat up with a negative current set point.
 
+If the Thermostat is used for temperature control with the Sinara 5432 DAC "Zotino", and is connected via an IDC cable, the TEC polarity may need to be reversed with the `pwm <ch> polarity reversed` TCP command.
+
 Testing heat flow direction with a low set current is recommended before installation of the TEC module.
 
 ### Limits

src/channel_state.rs

@@ -17,7 +17,7 @@ use crate::{
     ad7172,
     pid,
     steinhart_hart as sh,
-    command_parser::CenterPoint,
+    command_parser::{CenterPoint, Polarity},
 };
 
 const R_INNER: f64 = 2.0 * 5100.0;
@@ -35,6 +35,7 @@ pub struct ChannelState {
     pub pid_engaged: bool,
     pub pid: pid::Controller,
     pub sh: sh::Parameters,
+    pub polarity: Polarity,
 }
 
 impl ChannelState {
@@ -51,6 +52,7 @@ impl ChannelState {
             pid_engaged: false,
             pid: pid::Controller::new(pid::Parameters::default()),
             sh: sh::Parameters::default(),
+            polarity: Polarity::Normal,
         }
     }
 

src/channels.rs

@@ -17,7 +17,7 @@ use crate::{
     ad7172,
     channel::{Channel, Channel0, Channel1},
     channel_state::ChannelState,
-    command_parser::{CenterPoint, PwmPin},
+    command_parser::{CenterPoint, PwmPin, Polarity},
     command_handler::JsonBuffer,
     pins::{self, Channel0VRef, Channel1VRef},
     steinhart_hart,
@@ -158,6 +158,11 @@ impl Channels {
 
     pub fn set_i(&mut self, channel: usize, i_set: ElectricCurrent) -> ElectricCurrent {
         let i_set = i_set.min(MAX_TEC_I).max(-MAX_TEC_I);
+        self.channel_state(channel).i_set = i_set;
+        let negate = match self.channel_state(channel).polarity {
+            Polarity::Normal => 1.0,
+            Polarity::Reversed => -1.0,
+        };
         let vref_meas = match channel.into() {
             0 => self.channel0.vref_meas,
             1 => self.channel1.vref_meas,
@@ -165,10 +170,9 @@ impl Channels {
         };
         let center_point = vref_meas;
         let r_sense = ElectricalResistance::new::<ohm>(R_SENSE);
-        let voltage = i_set * 10.0 * r_sense + center_point;
+        let voltage = negate * i_set * 10.0 * r_sense + center_point;
         let voltage = self.set_dac(channel, voltage);
-        let i_set = (voltage - center_point) / (10.0 * r_sense);
-        self.channel_state(channel).i_set = i_set;
+        let i_set = negate * (voltage - center_point) / (10.0 * r_sense);
         i_set
     }
 
@@ -386,18 +390,28 @@ impl Channels {
     }
 
     pub fn get_max_i_pos(&mut self, channel: usize) -> (ElectricCurrent, ElectricCurrent) {
-        let duty = self.get_pwm(channel, PwmPin::MaxIPos);
+        let duty = match self.channel_state(channel).polarity {
+            Polarity::Normal => self.get_pwm(channel, PwmPin::MaxIPos),
+            Polarity::Reversed => self.get_pwm(channel, PwmPin::MaxINeg),
+        };
         (duty * MAX_TEC_I_DUTY_TO_CURRENT_RATE, MAX_TEC_I)
     }
 
     pub fn get_max_i_neg(&mut self, channel: usize) -> (ElectricCurrent, ElectricCurrent) {
-        let duty = self.get_pwm(channel, PwmPin::MaxINeg);
+        let duty = match self.channel_state(channel).polarity {
+            Polarity::Normal => self.get_pwm(channel, PwmPin::MaxINeg),
+            Polarity::Reversed => self.get_pwm(channel, PwmPin::MaxIPos),
+        };
         (duty * MAX_TEC_I_DUTY_TO_CURRENT_RATE, MAX_TEC_I)
     }
 
     // Get current passing through TEC
     pub fn get_tec_i(&mut self, channel: usize) -> ElectricCurrent {
-        (self.adc_read(channel, PinsAdcReadTarget::ITec, 16) - self.adc_read(channel, PinsAdcReadTarget::VREF, 16)) / ElectricalResistance::new::<ohm>(0.4)
+        let tec_i = (self.adc_read(channel, PinsAdcReadTarget::ITec, 16) - self.adc_read(channel, PinsAdcReadTarget::VREF, 16)) / ElectricalResistance::new::<ohm>(0.4);
+        match self.channel_state(channel).polarity {
+            Polarity::Normal => tec_i,
+            Polarity::Reversed => -tec_i,
+        }
     }
 
     // Get voltage across TEC
@@ -442,17 +456,36 @@ impl Channels {
     pub fn set_max_i_pos(&mut self, channel: usize, max_i_pos: ElectricCurrent) -> (ElectricCurrent, ElectricCurrent) {
         let max = ElectricCurrent::new::<ampere>(3.0);
         let duty = (max_i_pos.min(MAX_TEC_I).max(ElectricCurrent::zero()) / MAX_TEC_I_DUTY_TO_CURRENT_RATE).get::<ratio>();
-        let duty = self.set_pwm(channel, PwmPin::MaxIPos, duty);
+        let duty = match self.channel_state(channel).polarity {
+            Polarity::Normal => self.set_pwm(channel, PwmPin::MaxIPos, duty),
+            Polarity::Reversed => self.set_pwm(channel, PwmPin::MaxINeg, duty),
+        };
         (duty * MAX_TEC_I_DUTY_TO_CURRENT_RATE, max)
     }
 
     pub fn set_max_i_neg(&mut self, channel: usize, max_i_neg: ElectricCurrent) -> (ElectricCurrent, ElectricCurrent) {
         let max = ElectricCurrent::new::<ampere>(3.0);
         let duty = (max_i_neg.min(MAX_TEC_I).max(ElectricCurrent::zero()) / MAX_TEC_I_DUTY_TO_CURRENT_RATE).get::<ratio>();
-        let duty = self.set_pwm(channel, PwmPin::MaxINeg, duty);
+        let duty = match self.channel_state(channel).polarity {
+            Polarity::Normal => self.set_pwm(channel, PwmPin::MaxINeg, duty),
+            Polarity::Reversed => self.set_pwm(channel, PwmPin::MaxIPos, duty),
+        };
         (duty * MAX_TEC_I_DUTY_TO_CURRENT_RATE, max)
     }
 
+    pub fn set_polarity(&mut self, channel: usize, polarity: Polarity) {
+        if self.channel_state(channel).polarity != polarity {
+            let i_set = self.channel_state(channel).i_set;
+            let max_i_pos = self.get_max_i_pos(channel).0;
+            let max_i_neg = self.get_max_i_neg(channel).0;
+            self.channel_state(channel).polarity = polarity;
+
+            self.set_i(channel, i_set);
+            self.set_max_i_pos(channel, max_i_pos);
+            self.set_max_i_neg(channel, max_i_neg);
+        }
+    }
+
     fn report(&mut self, channel: usize) -> Report {
         let i_set = self.get_i(channel);
         let i_tec = self.adc_read(channel, PinsAdcReadTarget::ITec, 16);

src/command_handler.rs

@@ -11,7 +11,8 @@ use super::{
         CenterPoint, 
         PidParameter, 
         PwmPin, 
-        ShParameter
+        ShParameter,
+        Polarity
     },
     ad7172,
     CHANNEL_CONFIG_KEY,
@@ -170,6 +171,12 @@ impl Handler {
         Ok(Handler::Handled)
     }
 
+    fn set_polarity(socket: &mut TcpSocket, channels: &mut Channels, channel: usize, polarity: Polarity) -> Result<Handler, Error> {
+        channels.set_polarity(channel, polarity);
+        send_line(socket, b"{}");
+        Ok(Handler::Handled)
+    }
+
     fn set_pwm (socket: &mut TcpSocket, channels: &mut Channels, channel: usize, pin: PwmPin, value: f64) -> Result<Handler, Error> {
         match pin {
             PwmPin::ISet => {
@@ -411,6 +418,7 @@ impl Handler {
             Command::Show(ShowCommand::PostFilter) => Handler::show_post_filter(socket, channels),
             Command::Show(ShowCommand::Ipv4) => Handler::show_ipv4(socket, ipv4_config),
             Command::PwmPid { channel } => Handler::engage_pid(socket, channels, channel),
+            Command::PwmPolarity { channel, polarity } => Handler::set_polarity(socket, channels, channel, polarity),
             Command::Pwm { channel, pin, value } => Handler::set_pwm(socket, channels, channel, pin, value),
             Command::CenterPoint { channel, center } => Handler::set_center_point(socket, channels, channel, center),
             Command::Pid { channel, parameter, value } => Handler::set_pid(socket, channels, channel, parameter, value),

src/command_parser.rs

@@ -135,6 +135,12 @@ pub enum CenterPoint {
     Override(f32),
 }
 
+#[derive(Debug, Clone, PartialEq, Serialize, Deserialize)]
+pub enum Polarity {
+    Normal,
+    Reversed,
+}
+
 #[derive(Debug, Clone, PartialEq)]
 pub enum Command {
     Quit,
@@ -157,6 +163,10 @@ pub enum Command {
     PwmPid {
         channel: usize,
     },
+    PwmPolarity {
+        channel: usize,
+        polarity: Polarity,
+    },
     CenterPoint {
         channel: usize,
         center: CenterPoint,
@@ -297,6 +307,18 @@ fn pwm_pid(input: &[u8]) -> IResult<&[u8], ()> {
     value((), tag("pid"))(input)
 }
 
+fn pwm_polarity(input: &[u8]) -> IResult<&[u8], Polarity> {
+    preceded(
+        tag("polarity"),
+        preceded(
+            whitespace,
+            alt((value(Polarity::Normal, tag("normal")),
+                 value(Polarity::Reversed, tag("reversed"))
+            ))
+        )
+    )(input)
+}
+
 fn pwm(input: &[u8]) -> IResult<&[u8], Result<Command, Error>> {
     let (input, _) = tag("pwm")(input)?;
     alt((
@@ -309,6 +331,10 @@ fn pwm(input: &[u8]) -> IResult<&[u8], Result<Command, Error>> {
                     let (input, ()) = pwm_pid(input)?;
                     Ok((input, Ok(Command::PwmPid { channel })))
                 },
+                |input| {
+                    let (input, polarity) = pwm_polarity(input)?;
+                    Ok((input, Ok(Command::PwmPolarity { channel, polarity })))
+                },
                 |input| {
                     let (input, config) = pwm_setup(input)?;
                     match config {

src/config.rs

@@ -8,7 +8,7 @@ use uom::si::{
 use crate::{
     ad7172::PostFilter,
     channels::Channels,
-    command_parser::CenterPoint,
+    command_parser::{CenterPoint, Polarity},
     pid,
     steinhart_hart,
 };
@@ -20,6 +20,7 @@ pub struct ChannelConfig {
     pid_target: f32,
     pid_engaged: bool,
     i_set: ElectricCurrent,
+    polarity: Polarity,
     sh: steinhart_hart::Parameters,
     pwm: PwmLimits,
     /// uses variant `PostFilter::Invalid` instead of `None` to save space
@@ -45,7 +46,8 @@ impl ChannelConfig {
             pid: state.pid.parameters.clone(),
             pid_target: state.pid.target as f32,
             pid_engaged: state.pid_engaged,
-            i_set: i_set,
+            i_set,
+            polarity: state.polarity.clone(),
             sh: state.sh.clone(),
             pwm,
             adc_postfilter,
@@ -68,6 +70,7 @@ impl ChannelConfig {
         };
         let _ = channels.adc.set_postfilter(channel as u8, adc_postfilter);
         let _ = channels.set_i(channel, self.i_set);
+        channels.set_polarity(channel, self.polarity.clone());
     }
 }