LD: Rst LD current at power_up for soft start

- Verified to be working

.cargo/config

@@ -5,8 +5,4 @@ rustflags = [
 ]
 
 [build]
-# Pick ONE of these compilation targets
-# target = "thumbv6m-none-eabi"    # Cortex-M0 and Cortex-M0+
-# target = "thumbv7m-none-eabi"    # Cortex-M3
-# target = "thumbv7em-none-eabi"   # Cortex-M4 and Cortex-M7 (no FPU)
 target = "thumbv7em-none-eabihf" # Cortex-M4F and Cortex-M7F (with FPU)

src/device/boot.rs

@@ -13,6 +13,7 @@ use stm32f4xx_hal::{
     watchdog::IndependentWatchdog,
 };
 
+use uom::si::electric_current::milliampere;
 use uom::si::{electric_current::ampere, f64::ElectricCurrent};
 
 #[cfg(not(feature = "semihosting"))]
@@ -65,6 +66,7 @@ pub fn bootup(
     laser.ld_open();
     laser.set_ld_drive_current_limit(ElectricCurrent::new::<ampere>(0.2));
     laser.ld_set_i(ElectricCurrent::new::<ampere>(0.15));
+    laser.set_pd_i_limit(ElectricCurrent::new::<milliampere>(2.5));
     laser.power_up();
 
     let tec_driver = MAX1968::new(max1968_phy, perif.ADC1);
@@ -76,6 +78,8 @@ pub fn bootup(
     thermostat.calibrate_dac_value();
     thermostat.set_i(ElectricCurrent::new::<ampere>(1.0));
 
+    laser.set_pd_mon_calibrated_vdda(thermostat.get_calibrated_vdda());
+
     let flash_store = flash_store::store(perif.FLASH);
 
     let mut wd = IndependentWatchdog::new(perif.IWDG);

src/device/gpio.rs

@@ -1,6 +1,6 @@
 use crate::laser_diode::ld_ctrl::{self, LdCtrlPhy};
 use crate::laser_diode::max5719;
-use crate::laser_diode::analog_wdg::LdAnalogWdgPhy;
+use crate::laser_diode::ld_pwr_exc_protector::LdPwrExcProtectorPhy;
 use crate::thermostat::ad5680;
 use crate::thermostat::max1968::{self, MAX1968PinSet, MAX1968Phy, PWM_FREQ_KHZ};
 use crate::thermostat::ad7172;
@@ -40,7 +40,7 @@ pub fn setup(
     LdCtrlPhy<ld_ctrl::Channel0>,
     ad7172::AdcPhy,
     MAX1968Phy<max1968::Channel0>,
-    LdAnalogWdgPhy
+    LdPwrExcProtectorPhy
 ) {
     let gpioa = gpioa.split();
     let gpiob = gpiob.split();
@@ -84,7 +84,7 @@ pub fn setup(
         current_source_short_pin: gpioa.pa4.into_push_pull_output(),
     };
 
-    let pd_mon_phy = LdAnalogWdgPhy {
+    let pd_mon_phy = LdPwrExcProtectorPhy {
         _pd_mon_ch0: gpioa.pa3.into_analog(),
         pwr_en_ch0: gpiod.pd9.into_push_pull_output(),
     };

src/laser_diode/analog_wdg.rs

@@ -1,208 +0,0 @@
-// stm32f4xx_hal does not provide config and driver for analog watchdog yet
-use stm32f4xx_hal::{
-    pac::{ADC2, NVIC},
-    gpio::{Analog, Output, PushPull, gpioa::PA3, gpiod::PD9},
-    interrupt,
-};
-use uom::si::electric_potential::millivolt;
-use uom::si::f64::ElectricPotential;
-
-// 12 bit Resolution
-const MAX_SAMPLE: u16 = 4095;
-
-pub type LdPwrEnPinType = PD9<Output<PushPull>>;
-pub type PdMonAdcPinType = PA3<Analog>;
-
-static mut ANALOG_WDG: Option<LdAnalogWdg> = None;
-
-pub struct LdAnalogWdgPhy {
-    // To make sure PA3 is configured to Analog mode
-    pub _pd_mon_ch0: PdMonAdcPinType, 
-    pub pwr_en_ch0:  LdPwrEnPinType,
-}
-
-
-#[derive(Clone)]
-pub struct AlarmStatus {
-    alarm: bool,
-    val: u16,
-}
-
-pub struct LdAnalogWdg {
-    pac: ADC2,
-    phy: LdAnalogWdgPhy,
-    alarm_status: AlarmStatus,
-    //Calibrated VDDA in millivolt from Adc<ADC1>.calibrate() 
-    calibrated_vdda: u32, 
-}
-
-impl LdAnalogWdg {
-    /// ADC interrupt is disabled and continuous conversion is started by default
-    pub fn setup(pac: ADC2, phy: LdAnalogWdgPhy){
-        unsafe { ANALOG_WDG = Some(LdAnalogWdg{ 
-            pac: pac, 
-            phy: phy,
-            alarm_status: AlarmStatus {
-                    alarm: false,
-                    val: 0x0000,
-            },
-            calibrated_vdda: 3300,
-            });
-        }
-
-        unsafe {
-            if let Some(ref mut wdg ) = LdAnalogWdg::get() {
-                wdg.pac.cr1.write(|w| w
-                    // 12 Bit Resolution
-                    .res().twelve_bit()
-                    // Enable Analog Watchdog on Single Regular Channel
-                    .awden().enabled()
-                    .awdsgl().single_channel()
-                    .jawden().disabled()
-                    // Disable Analog Watchdog Interrupt
-                    .awdie().disabled()
-                    // Select Analog Watchdog Channel 3 (PA3) on ADC2
-                    .awdch().bits(0x03)
-                );
-                wdg.pac.cr2.write(|w| w
-                    // Continous Conversion mode
-                    .cont().set_bit()
-                    // Enable ADC
-                    .adon().set_bit()
-                    // Start ADC Conversion
-                    .swstart().set_bit()
-                );
-                // Set Sampling Time for Channel 3 to 480 Cycle
-                wdg.pac.smpr2.write(|w| w 
-                    .smp3().cycles480()
-                );
-                // Set the high threshold to be max value initially
-                wdg.pac.htr.write(|w| w.bits(0xFFFF_FFFF));
-                // Set the high threshold to be min value initially
-                wdg.pac.ltr.write(|w| w.bits(0x0000_0000));
-                // Set the Conversion Sequence to only have Channel 3 (PA3)
-                wdg.pac.sqr3.write(|w| w
-                    .sq1().bits(0x03)
-                );
-            }
-        }
-    }
-
-    fn get() -> Option<&'static mut Self> {
-        unsafe { ANALOG_WDG.as_mut() }
-    }
-
-    /// This fn accepts the calibrated vdda value from Adc<ADC1>.calibrate()
-    pub fn set_calibrated_vdda(val: u32) {
-        if let Some(ref mut wdg ) = LdAnalogWdg::get() {
-            wdg.calibrated_vdda = val;
-        }
-    }
-
-    pub fn get_pd_v() -> ElectricPotential {
-        if let Some(ref mut wdg ) = LdAnalogWdg::get() {
-            let sample = wdg.pac.dr.read().data().bits();
-
-            return ElectricPotential::new::<millivolt>(((u32::from(sample) * wdg.calibrated_vdda) / u32::from(MAX_SAMPLE)) as f64)
-        }
-        ElectricPotential::new::<millivolt>(0.0)
-    }
-
-    fn set_alarm(){
-        if let Some(ref mut wdg ) = LdAnalogWdg::get() {
-            wdg.alarm_status = AlarmStatus {
-                alarm: true,
-                val: wdg.pac.dr.read().data().bits(),
-            };
-        }
-    }
-
-    pub fn get_alarm_status() -> AlarmStatus {
-        if let Some(ref mut wdg ) = LdAnalogWdg::get() {
-            return wdg.alarm_status.clone()
-        }
-        AlarmStatus {
-            alarm: false,
-            val: 0x0000,
-        }
-    }
-
-    pub fn clear_alarm_status(){
-        if let Some(ref mut wdg ) = LdAnalogWdg::get() {
-            wdg.alarm_status = AlarmStatus {
-                alarm: false,
-                val: 0x0000,
-            };
-        }
-    }
-
-    /// Set ADC Watchdog Higher threshold register
-    /// Interrupt is triggered when ADC value is ABOVE the value set
-    pub fn set_htr(htr: u32){
-        if let Some(ref mut wdg ) = LdAnalogWdg::get() {
-            wdg.pac.htr.write(|w| unsafe {w.bits(htr)});
-        }
-    }
-
-    /// Set ADC Watchdog Lower threshold register
-    /// Interrupt is triggered when ADC value is BELOW the value set
-    #[allow(unused)]
-    pub fn set_ltr(ltr:u32){
-        if let Some(ref mut wdg ) = LdAnalogWdg::get() {
-            wdg.pac.ltr.write(|w| unsafe {w.bits(ltr)});
-        }
-    }
-
-    pub fn enable_watchdog_interrupt(){
-        if let Some(ref mut wdg ) = LdAnalogWdg::get() {
-            wdg.pac.cr1.modify(|_, w| w
-                .awdie().set_bit()
-            );
-        }
-    }
-
-    pub fn disable_watchdog_interrupt(){
-        if let Some(ref mut wdg ) = LdAnalogWdg::get() {
-            wdg.pac.cr1.modify(|_, w| w
-                .awdie().clear_bit()
-            );
-        }
-    }
-
-    fn clear_interrupt_bit(){
-        unsafe{
-            NVIC::unmask(interrupt::ADC);
-        }
-    }
-
-    pub fn is_pwr_engaged() -> bool{
-        if let Some(ref mut wdg ) = LdAnalogWdg::get() {
-            return wdg.phy.pwr_en_ch0.is_set_high()
-        }
-        false
-    }
-
-    pub fn pwr_engage(){
-        if let Some(ref mut wdg ) = LdAnalogWdg::get() {
-            wdg.phy.pwr_en_ch0.set_high()
-        }
-    }
-
-    pub fn pwr_disengage(){
-        if let Some(ref mut wdg ) = LdAnalogWdg::get() {
-            wdg.phy.pwr_en_ch0.set_low()
-        }
-    }
-}
-
-#[interrupt]
-fn ADC(){
-    cortex_m::interrupt::free(|_| {
-            LdAnalogWdg::set_alarm();
-            LdAnalogWdg::pwr_disengage();
-            // Disable interrupt to avoid getting stuck in infinite interrupt loop
-            LdAnalogWdg::disable_watchdog_interrupt();
-            LdAnalogWdg::clear_interrupt_bit();
-        }
-    )
-}

src/laser_diode/laser_diode.rs

@@ -1,22 +1,24 @@
 use miniconf::Miniconf;
 use stm32f4xx_hal::pac::ADC2;
+use uom::si::electric_current::ampere;
 use crate::laser_diode::ld_ctrl::LdCtrl;
-use crate::laser_diode::analog_wdg::{LdAnalogWdg, self};
-use core::{marker::PhantomData, f64::NAN};
+use crate::laser_diode::ld_pwr_exc_protector::{LdPwrExcProtector, self};
+use crate::laser_diode::pd_responsitivity;
+use core::marker::PhantomData;
+use crate::device::sys_timer::sleep;
 
 use uom::si::{
     electric_current::milliampere,
     f64::{ElectricPotential, ElectricCurrent, Power},
 };
+use num_traits::Float;
 
-use uom::{si::{ISQ, SI, Quantity}, typenum::*};
+use uom::{si::{ISQ, SI, Quantity, ratio::ratio}, typenum::*};
 
 // Volt / Ampere
 pub type TransimpedanceUnit = Quantity<ISQ<P2, P1, N3, N2, Z0, Z0, Z0>, SI<f64>, f64>;
 // Ampere / Volt
 type TransconductanceUnit = Quantity<ISQ<N2, N1, P3, P2, Z0, Z0, Z0>, SI<f64>, f64>;
-// Watt / Ampere
-pub type IToPowerUnit = Quantity<ISQ<P2, P1, N3, N1, Z0, Z0, Z0>, SI<f64>, f64>; 
 
 impl Settings{
     pub const DAC_OUT_V_MAX: ElectricPotential = ElectricPotential {
@@ -37,13 +39,22 @@ impl Settings{
         units: PhantomData,
         value: 10.0 / 0.75,
     };
+
+    const LD_CURRENT_STEP_SIZE: ElectricCurrent = ElectricCurrent {
+        dimension: PhantomData,
+        units: PhantomData,
+        value: 0.0001,
+    };
+
+    const LD_CURRENT_TIME_STEP_MS: u32 = 1;
 }
 
 #[derive(Clone, Debug, Miniconf)]
 pub struct Settings {
     ld_drive_current: ElectricCurrent,
     ld_drive_current_limit: ElectricCurrent,
-    pd_i_to_out_pwr: IToPowerUnit,
+    #[miniconf(defer)]
+    pd_responsitivity: pd_responsitivity::Parameters,
 }
 
 impl Default for Settings {
@@ -51,7 +62,7 @@ impl Default for Settings {
         Self {
             ld_drive_current: ElectricCurrent::new::<milliampere>(0.0),
             ld_drive_current_limit: ElectricCurrent::new::<milliampere>(0.0),
-            pd_i_to_out_pwr: IToPowerUnit {dimension: PhantomData, units: PhantomData, value: NAN}
+            pd_responsitivity: pd_responsitivity::Parameters::default(),
         }
     }
 }
@@ -62,8 +73,8 @@ pub struct LdDrive{
 }
 
 impl LdDrive{
-    pub fn new(current_source: LdCtrl, pins_adc: ADC2, phy: analog_wdg::LdAnalogWdgPhy)-> Self {
-        LdAnalogWdg::setup(pins_adc, phy);
+    pub fn new(current_source: LdCtrl, pins_adc: ADC2, phy: ld_pwr_exc_protector::LdPwrExcProtectorPhy)-> Self {
+        LdPwrExcProtector::setup(pins_adc, phy);
 
         LdDrive {
             ctrl: current_source,
@@ -72,7 +83,7 @@ impl LdDrive{
     }
 
     pub fn setup(&mut self) {
-        LdAnalogWdg::pwr_disengage();
+        LdPwrExcProtector::pwr_off();
         self.ld_set_i(ElectricCurrent::new::<milliampere>(0.0));
         self.ld_short();
     }
@@ -94,47 +105,73 @@ impl LdDrive{
     }
 
     pub fn power_up(&mut self){            
-        LdAnalogWdg::pwr_engage();
+        let _ = self.ctrl.set_i(ElectricCurrent::new::<milliampere>(0.0), Settings::LD_DRIVE_TRANSIMPEDANCE, Settings::DAC_OUT_V_MAX);
+        LdPwrExcProtector::pwr_on_and_arm_protection();
+        // Wait for LD Power Supply to start up before driving current to laser diode
+        sleep(30);
+        self.ld_set_i(self.settings.ld_drive_current);
     }
 
     pub fn power_down(&mut self){
-        LdAnalogWdg::pwr_disengage();
+        LdPwrExcProtector::pwr_off();
     }
 
     pub fn get_pd_i(&mut self) -> ElectricCurrent {
-        LdAnalogWdg::get_pd_v() * Settings::PD_MON_TRANSCONDUCTANCE
+        LdPwrExcProtector::get_status().v * Settings::PD_MON_TRANSCONDUCTANCE
     }
 
+    // Ramping up or down laser diode current according to preset current step size and time step.
     pub fn ld_set_i(&mut self, i: ElectricCurrent) -> ElectricCurrent {
-        let ld_i_set = i.min(self.settings.ld_drive_current_limit);
-        let ld_i_set = self.ctrl.set_i(ld_i_set, Settings::LD_DRIVE_TRANSIMPEDANCE, Settings::DAC_OUT_V_MAX);
-        self.settings.ld_drive_current = ld_i_set;
-        ld_i_set
+        let mut prev_i_set = self.settings.ld_drive_current;
+        let final_i_set = i.min(self.settings.ld_drive_current_limit).max(ElectricCurrent::new::<ampere>(0.0));
+        
+        let num_of_step = ((final_i_set - prev_i_set)/Settings::LD_CURRENT_STEP_SIZE).get::<ratio>().floor() as i32;
+
+        let current_step = if num_of_step.is_positive() {
+            Settings::LD_CURRENT_STEP_SIZE
+        } else { 
+            -Settings::LD_CURRENT_STEP_SIZE 
+        };
+        
+        for _ in (0..num_of_step.abs()).rev() {
+            prev_i_set = prev_i_set + current_step;
+            let _ = self.ctrl.set_i(prev_i_set, Settings::LD_DRIVE_TRANSIMPEDANCE, Settings::DAC_OUT_V_MAX);
+            sleep(Settings::LD_CURRENT_TIME_STEP_MS);
+        }
+        let prev_i_set = self.ctrl.set_i(final_i_set, Settings::LD_DRIVE_TRANSIMPEDANCE, Settings::DAC_OUT_V_MAX);
+
+        self.settings.ld_drive_current = prev_i_set;
+        prev_i_set
     }
 
     // Set the calibrated VDDA value obtained from ADC1 calibration
-    pub fn set_pd_mon_calibrated_vdda(val_cal: u32) {
-        LdAnalogWdg::set_calibrated_vdda(val_cal)
+    pub fn set_pd_mon_calibrated_vdda(&mut self, val_cal: u32) {
+        LdPwrExcProtector::set_calibrated_vdda(val_cal)
     }
 
-    pub fn pd_mon_status() -> analog_wdg::AlarmStatus {
-        LdAnalogWdg::get_alarm_status()
+    pub fn pd_mon_status(&mut self) -> ld_pwr_exc_protector::Status {
+        LdPwrExcProtector::get_status()
     }
 
     pub fn pd_mon_clear_alarm(&mut self) {
-        LdAnalogWdg::clear_alarm_status();
+        LdPwrExcProtector::clear_alarm_status();
     }
 
-    pub fn pd_mon_engage(){
-        LdAnalogWdg::enable_watchdog_interrupt()
+    pub fn set_pd_responsitivity(&mut self, responsitivity: pd_responsitivity::ResponsitivityUnit){
+        self.settings.pd_responsitivity.responsitivity = responsitivity;
     }
 
-    pub fn pd_mon_disengage(){
-        LdAnalogWdg::disable_watchdog_interrupt()
+    pub fn set_pd_dark_current(&mut self, i_dark: ElectricCurrent){
+        self.settings.pd_responsitivity.i_dark = i_dark;
     }
 
-    pub fn set_ld_power_limit(pwr_limit: Power){
-        // LdAnalogWdg::set_htr(convert pwr_limit to raw adc code)
-        unimplemented!()
+    pub fn set_ld_power_limit(&mut self, pwr_limit: Power){
+        LdPwrExcProtector::set_trigger_threshold_v(self.settings.pd_responsitivity
+            .get_ld_i_from_ld_pwr(pwr_limit) / Settings::PD_MON_TRANSCONDUCTANCE
+        );
+    }
+
+    pub fn set_pd_i_limit(&mut self, i: ElectricCurrent){
+        LdPwrExcProtector::set_trigger_threshold_v(i / Settings::PD_MON_TRANSCONDUCTANCE);
     }
 }

src/laser_diode/ld_pwr_exc_protector.rs

@@ -0,0 +1,237 @@
+use stm32f4xx_hal::pac;
+use stm32f4xx_hal::rcc::Enable;
+use stm32f4xx_hal::{
+    pac::{ADC2, NVIC},
+    gpio::{Analog, Output, PushPull, gpioa::PA3, gpiod::PD9},
+    interrupt,
+};
+use uom::si::{
+    electric_potential::millivolt,
+    f64::ElectricPotential,
+    ratio::ratio
+};
+
+// 12 bit Resolution
+const MAX_SAMPLE: u16 = 4095;
+pub type LdPwrEnPinType = PD9<Output<PushPull>>;
+pub type PdMonAdcPinType = PA3<Analog>;
+const PD_MON_ADC_CH_ID: u8 = 0x03;
+
+static mut LD_PWR_EXC_PROTECTOR: Option<LdPwrExcProtector> = None;
+
+pub struct LdPwrExcProtectorPhy {
+    // To make sure Pd Mon Pin is configured to Analog mode
+    pub _pd_mon_ch0: PdMonAdcPinType, 
+    pub pwr_en_ch0:  LdPwrEnPinType,
+}
+
+#[derive(Clone)]
+pub struct Status {
+    pub pwr_excursion: bool,
+    pub v_tripped: ElectricPotential,
+    pub pwr_engaged: bool,
+    pub v: ElectricPotential,
+}
+
+impl Default for Status {
+    fn default() -> Self {
+        Status {
+            pwr_excursion: false,
+            v_tripped: ElectricPotential::new::<millivolt>(0.0),
+            pwr_engaged: false,
+            v: ElectricPotential::new::<millivolt>(0.0),
+        }
+    }
+}
+
+pub struct LdPwrExcProtector {
+    pac: ADC2,
+    phy: LdPwrExcProtectorPhy,
+    alarm_status: Status,
+    calibrated_vdda: u32, 
+}
+
+impl LdPwrExcProtector {
+    /// ADC Analog Watchdog is configured to guard a single regular Adc channel on Pd Mon Pin.
+    /// ADC is configured to start continuous conversion without using DMA immediately.
+    /// Interrupt is disabled by default.
+    pub fn setup(pac_adc: ADC2, mut phy: LdPwrExcProtectorPhy){
+        unsafe {
+            // All ADCs share the same reset interface.
+            // NOTE(unsafe) this reference will only be used for atomic writes with no side effects.
+            let rcc = &(*pac::RCC::ptr());
+            // Enable the ADC2 Clock
+            pac::ADC2::enable(rcc);
+            // Enable ADC Interrupt
+            NVIC::unmask(interrupt::ADC);
+        }
+
+        pac_adc.cr1.reset();
+        pac_adc.cr2.reset();
+        pac_adc.sqr1.reset();
+        pac_adc.sqr2.reset();
+        pac_adc.sqr3.reset();
+        
+        pac_adc.cr1.write(|w| w
+            // 12 Bit Resolution
+            .res().twelve_bit()
+            // Set Analog Watchdog to guard Single Regular Channel
+            .awden().enabled()
+            .awdsgl().single_channel()
+            .jawden().disabled()
+            // Disable Analog Watchdog Interrupt
+            .awdie().disabled()
+            // Set Analog Watchdog to monitor Pd Mon Pin
+            .awdch().variant(PD_MON_ADC_CH_ID)
+        );
+        pac_adc.cr2.write(|w| w
+            // Continous Conversion Mode
+            .cont().set_bit()
+            // Power up ADC
+            .adon().set_bit()
+            // Set data alignment to the right
+            .align().right()
+            // End of conversion selection: Each Sequence
+            .eocs().each_sequence()
+            .exten().disabled()
+            .extsel().tim1cc1()
+        );
+        // Set the Conversion Sequence to include Pd Mon Pin
+        pac_adc.sqr3.write(|w| w
+            .sq1().variant(PD_MON_ADC_CH_ID)
+        );
+        // Set all sampling channels to have fastest sampling interval
+        pac_adc.smpr1.reset();
+        pac_adc.smpr2.reset();
+        
+        // Set the higher threshold to be max value initially
+        pac_adc.htr.write(|w| w.ht().variant(MAX_SAMPLE));
+        // Set the lower threshold to be min value initially
+        pac_adc.ltr.write(|w| w.lt().variant(0));
+
+        // SWStart should only be set when ADON = 1. Otherwise no conversion is launched.
+        pac_adc.cr2.modify(|_, w| w
+            .swstart().set_bit()
+        );
+
+        phy.pwr_en_ch0.set_low();
+
+        unsafe {
+            LD_PWR_EXC_PROTECTOR = Some(
+                LdPwrExcProtector { 
+                    pac: pac_adc, 
+                    phy: phy,
+                    alarm_status: Status::default(),
+                    calibrated_vdda: 3300,
+                }
+            );
+        }
+    }
+
+    fn get() -> Option<&'static mut Self> {
+        unsafe { LD_PWR_EXC_PROTECTOR.as_mut() }
+    }
+
+    fn convert_sample_to_volt(sample :u16) -> ElectricPotential {
+        if let Some(ref mut wdg ) = LdPwrExcProtector::get() {
+            return ElectricPotential::new::<millivolt>(((u32::from(sample) * wdg.calibrated_vdda) / u32::from(MAX_SAMPLE)) as f64)
+        }
+        ElectricPotential::new::<millivolt>(0.0)
+    }
+
+    pub fn set_trigger_threshold_v(htr: ElectricPotential){
+        if let Some(ref mut wdg ) = LdPwrExcProtector::get() {
+            let code: u32 = ((htr / (ElectricPotential::new::<millivolt>(wdg.calibrated_vdda as f64))).get::<ratio>() * (MAX_SAMPLE as f64)) as u32;
+            wdg.pac.htr.write(|w| unsafe {w.bits(code)});
+        }
+    }
+
+    pub fn set_calibrated_vdda(val: u32) {
+        if let Some(ref mut wdg ) = LdPwrExcProtector::get() {
+            wdg.calibrated_vdda = val;
+        }
+    }
+
+    pub fn get_status() -> Status {
+        if let Some(ref mut wdg ) = LdPwrExcProtector::get() {
+            wdg.alarm_status.v = LdPwrExcProtector::convert_sample_to_volt(wdg.pac.dr.read().data().bits());
+            return wdg.alarm_status.clone()
+        }
+        Status::default()
+    }
+
+    pub fn pwr_on_and_arm_protection(){
+        if let Some(ref mut wdg ) = LdPwrExcProtector::get() {
+            wdg.alarm_status = Status::default();
+            LdPwrExcProtector::pwr_on();
+            // Interrupt should be enabled after power on to tackle the following edge case:
+            //      Pd_Mon pin voltage has already exceed threshold before LD Power is on.
+            LdPwrExcProtector::enable_watchdog_interrupt();
+        }
+    }
+
+    pub fn clear_alarm_status(){
+        if let Some(ref mut wdg ) = LdPwrExcProtector::get() {
+            wdg.alarm_status.pwr_excursion = false;
+            wdg.alarm_status.v_tripped = ElectricPotential::new::<millivolt>(0.0);
+        }
+    }
+
+    fn enable_watchdog_interrupt(){
+        if let Some(ref mut wdg ) = LdPwrExcProtector::get() {
+            wdg.pac.cr1.modify(|_, w| w
+                .awdie().set_bit()
+            );
+        }
+    }
+
+    fn disable_watchdog_interrupt(){
+        if let Some(ref mut wdg ) = LdPwrExcProtector::get() {
+            wdg.pac.cr1.modify(|_, w| w
+                .awdie().clear_bit()
+            );
+        }
+    }
+
+    fn clear_interrupt_bit(){
+        if let Some(ref mut wdg ) = LdPwrExcProtector::get() {
+            wdg.pac.sr.modify(|_, w| w
+                .awd().clear_bit()
+            );
+        }
+    }
+
+    fn pwr_on(){
+        if let Some(ref mut wdg ) = LdPwrExcProtector::get() {
+            wdg.alarm_status.pwr_engaged = true;
+            wdg.phy.pwr_en_ch0.set_high()
+        }
+    }
+
+    pub fn pwr_off(){
+        if let Some(ref mut wdg ) = LdPwrExcProtector::get() {
+            wdg.alarm_status.pwr_engaged = false;
+            wdg.phy.pwr_en_ch0.set_low()
+        }
+    }
+
+    fn pwr_excursion_handler(){
+        if let Some(ref mut wdg ) = LdPwrExcProtector::get() {
+            let sample = wdg.pac.dr.read().data().bits();
+            LdPwrExcProtector::pwr_off();
+            wdg.alarm_status.pwr_excursion = true;
+            wdg.alarm_status.v_tripped = LdPwrExcProtector::convert_sample_to_volt(sample);
+        }
+    }
+}
+
+#[interrupt]
+fn ADC(){
+    cortex_m::interrupt::free(|_| {
+            LdPwrExcProtector::pwr_excursion_handler();
+            // Disable interrupt to avoid getting stuck in infinite loop
+            LdPwrExcProtector::disable_watchdog_interrupt();
+            LdPwrExcProtector::clear_interrupt_bit();
+        }
+    )
+}

src/laser_diode/mod.rs

@@ -1,5 +1,5 @@
 pub mod ld_ctrl;
 pub mod max5719;
 pub mod laser_diode;
-pub mod pd_mon;
-pub mod analog_wdg;
+pub mod pd_responsitivity;
+pub mod ld_pwr_exc_protector;

src/laser_diode/pd_responsitivity.rs

@@ -12,19 +12,22 @@ use miniconf::Miniconf;
 // Ampere / Watt
 pub type ResponsitivityUnit = Quantity<ISQ<N2, N1, P3, P1, Z0, Z0, Z0>, SI<f64>, f64>; 
 
-/// Steinhart-Hart equation Photodiode
 #[derive(Clone, Debug, PartialEq, Miniconf)]
 pub struct Parameters {
-    /// Responsitivity
     pub responsitivity: ResponsitivityUnit,
     pub i_dark: ElectricCurrent,
 }
 
 impl Parameters {
-    pub fn get_ld_output_power(&self, i: ElectricCurrent) -> Power {
+    pub fn get_ld_pwr_from_ld_i(&self, i: ElectricCurrent) -> Power {
         let ld_power = (i - self.i_dark) / self.responsitivity;
         ld_power
     }
+
+    pub fn get_ld_i_from_ld_pwr(&self, pwr: Power) -> ElectricCurrent {
+        let ld_i = pwr * self.responsitivity + self.i_dark;
+        ld_i
+    }
 }
 
 impl Default for Parameters {

src/main.rs

@@ -81,6 +81,9 @@ fn main() -> ! {
         info!("curr_tec_i: {:?}", amp_fmt.with(thermostat.get_tec_i()));
         info!("curr_tec_v: {:?}", volt_fmt.with(thermostat.get_tec_v()));
 
-        sys_timer::sleep(10);
+        info!("pd_mon_v: {:?}", volt_fmt.with(laser.pd_mon_status().v));
+        info!("power_excursion: {:?}", laser.pd_mon_status().pwr_excursion);
+        
+        sys_timer::sleep(500);
     }
 }

src/thermostat/max1968.rs

@@ -113,18 +113,13 @@ impl<C: ChannelPins> MAX1968Phy<C> {
 
 impl MAX1968 {
     pub fn new(phy_ch0: MAX1968Phy<Channel0>, adc1: ADC1) -> Self {
-        // Set ADC to a slowest sampling interval for more accurate calibration
         let config = AdcConfig::default()
             .clock(config::Clock::Pclk2_div_8)
             .default_sample_time(config::SampleTime::Cycles_480);
-        let mut pins_adc = Adc::adc1(adc1, true, config);
+        // Do not set reset RCCs as it causes other ADCs' clock to be disabled
+        let mut pins_adc = Adc::adc1(adc1, false, config);
         pins_adc.calibrate();
 
-        let config = AdcConfig::default()
-            .clock(config::Clock::Pclk2_div_8)
-            .default_sample_time(config::SampleTime::Cycles_480);
-        pins_adc.apply_config(config);
-
         MAX1968 {
             phy: phy_ch0,
             pins_adc: pins_adc,