mirror of
https://github.com/m-labs/artiq.git
synced 2024-12-11 12:46:37 +08:00
204 lines
5.3 KiB
Python
204 lines
5.3 KiB
Python
from migen.fhdl.std import *
|
|
from migen.genlib.fsm import *
|
|
from migen.bus import wishbone
|
|
from migen.bus.transactions import *
|
|
from migen.sim.generic import run_simulation
|
|
|
|
|
|
class AD9858(Module):
|
|
"""Wishbone interface to the AD9858 DDS chip.
|
|
|
|
Addresses 0-63 map the AD9858 registers.
|
|
Data is zero-padded.
|
|
|
|
Write to address 64 to pulse the FUD signal.
|
|
Address 65 is a GPIO register that controls the sel, p and reset signals.
|
|
sel is mapped to the lower bits, followed by p and reset.
|
|
|
|
Write timing:
|
|
Address is set one cycle before assertion of we_n.
|
|
we_n is asserted for one cycle, at the same time as valid data is driven.
|
|
|
|
Read timing:
|
|
Address is set one cycle before assertion of rd_n.
|
|
rd_n is asserted for 3 cycles.
|
|
Data is sampled 2 cycles into the assertion of rd_n.
|
|
|
|
Design:
|
|
All IO pads are registered.
|
|
|
|
LVDS driver/receiver propagation delays are 3.6+4.5 ns max
|
|
LVDS state transition delays are 20, 15 ns max
|
|
Schmitt trigger delays are 6.4ns max
|
|
Round-trip addr A setup (> RX, RD, D to Z), RD prop, D valid (< D
|
|
valid), D prop is ~15 + 10 + 20 + 10 = 55ns
|
|
"""
|
|
def __init__(self, pads, drive_fud=False, bus=None):
|
|
if bus is None:
|
|
bus = wishbone.Interface()
|
|
self.bus = bus
|
|
|
|
# # #
|
|
|
|
dts = TSTriple(8)
|
|
self.specials += dts.get_tristate(pads.d)
|
|
dr = Signal(8)
|
|
rx = Signal()
|
|
self.sync += [
|
|
pads.a.eq(bus.adr),
|
|
dts.o.eq(bus.dat_w),
|
|
dr.eq(dts.i),
|
|
dts.oe.eq(~rx)
|
|
]
|
|
|
|
gpio = Signal(flen(pads.sel) + flen(pads.p) + 1)
|
|
gpio_load = Signal()
|
|
self.sync += If(gpio_load, gpio.eq(bus.dat_w))
|
|
self.comb += [
|
|
Cat(pads.sel, pads.p).eq(gpio),
|
|
pads.rst_n.eq(~gpio[-1]),
|
|
]
|
|
|
|
bus_r_gpio = Signal()
|
|
self.comb += If(bus_r_gpio,
|
|
bus.dat_r.eq(gpio)
|
|
).Else(
|
|
bus.dat_r.eq(dr)
|
|
)
|
|
|
|
if drive_fud:
|
|
fud = Signal()
|
|
self.sync += pads.fud_n.eq(~fud)
|
|
|
|
pads.wr_n.reset = 1
|
|
pads.rd_n.reset = 1
|
|
wr = Signal()
|
|
rd = Signal()
|
|
self.sync += pads.wr_n.eq(~wr), pads.rd_n.eq(~rd)
|
|
|
|
fsm = FSM("IDLE")
|
|
self.submodules += fsm
|
|
|
|
fsm.act("IDLE",
|
|
If(bus.cyc & bus.stb,
|
|
If(bus.adr[6],
|
|
If(bus.adr[0],
|
|
NextState("GPIO")
|
|
).Else(
|
|
NextState("FUD") if drive_fud else None
|
|
)
|
|
).Else(
|
|
If(bus.we,
|
|
NextState("WRITE")
|
|
).Else(
|
|
NextState("READ")
|
|
)
|
|
)
|
|
)
|
|
)
|
|
fsm.act("WRITE",
|
|
# 3ns A setup to WR active
|
|
wr.eq(1),
|
|
NextState("WRITE0")
|
|
)
|
|
fsm.act("WRITE0",
|
|
# 3.5ns D setup to WR inactive
|
|
# 0ns D and A hold to WR inactive
|
|
bus.ack.eq(1),
|
|
NextState("IDLE")
|
|
)
|
|
fsm.act("READ",
|
|
# 15ns D valid to A setup
|
|
# 15ns D valid to RD active
|
|
rx.eq(1),
|
|
rd.eq(1),
|
|
NextState("READ0")
|
|
)
|
|
fsm.act("READ0",
|
|
rx.eq(1),
|
|
rd.eq(1),
|
|
NextState("READ1")
|
|
)
|
|
fsm.act("READ1",
|
|
rx.eq(1),
|
|
rd.eq(1),
|
|
NextState("READ2")
|
|
)
|
|
fsm.act("READ2",
|
|
rx.eq(1),
|
|
rd.eq(1),
|
|
NextState("READ3")
|
|
)
|
|
fsm.act("READ3",
|
|
rx.eq(1),
|
|
rd.eq(1),
|
|
NextState("READ4")
|
|
)
|
|
fsm.act("READ4",
|
|
rx.eq(1),
|
|
NextState("READ5")
|
|
)
|
|
fsm.act("READ5",
|
|
# 5ns D three-state to RD inactive
|
|
# 10ns A hold to RD inactive
|
|
rx.eq(1),
|
|
bus.ack.eq(1),
|
|
NextState("IDLE")
|
|
)
|
|
if drive_fud:
|
|
fsm.act("FUD",
|
|
# 4ns FUD setup to SYNCLK
|
|
# 0ns FUD hold to SYNCLK
|
|
fud.eq(1),
|
|
bus.ack.eq(1),
|
|
NextState("IDLE")
|
|
)
|
|
fsm.act("GPIO",
|
|
bus.ack.eq(1),
|
|
bus_r_gpio.eq(1),
|
|
If(bus.we, gpio_load.eq(1)),
|
|
NextState("IDLE")
|
|
)
|
|
|
|
|
|
def _test_gen():
|
|
# Test external bus writes
|
|
yield TWrite(4, 2)
|
|
yield TWrite(5, 3)
|
|
yield
|
|
# Test external bus reads
|
|
yield TRead(14)
|
|
yield TRead(15)
|
|
yield
|
|
# Test FUD
|
|
yield TWrite(64, 0)
|
|
yield
|
|
# Test GPIO
|
|
yield TWrite(65, 0xff)
|
|
yield
|
|
|
|
|
|
class _TestPads:
|
|
def __init__(self):
|
|
self.a = Signal(6)
|
|
self.d = Signal(8)
|
|
self.sel = Signal(5)
|
|
self.p = Signal(2)
|
|
self.fud_n = Signal()
|
|
self.wr_n = Signal()
|
|
self.rd_n = Signal()
|
|
self.rst_n = Signal()
|
|
|
|
|
|
class _TB(Module):
|
|
def __init__(self):
|
|
pads = _TestPads()
|
|
self.submodules.dut = AD9858(pads, drive_fud=True)
|
|
self.submodules.initiator = wishbone.Initiator(_test_gen())
|
|
self.submodules.interconnect = wishbone.InterconnectPointToPoint(
|
|
self.initiator.bus, self.dut.bus)
|
|
|
|
|
|
if __name__ == "__main__":
|
|
run_simulation(_TB(), vcd_name="ad9858.vcd")
|