mirror of https://github.com/m-labs/artiq.git
120 lines
6.2 KiB
ReStructuredText
120 lines
6.2 KiB
ReStructuredText
ARTIQ Phaser
|
|
============
|
|
|
|
This ARTIQ branch contains a proof-of-concept design of a GHz-datarate multichannel direct digital synthesizer (DDS) compatible with ARTIQ's RTIO channels.
|
|
In later developments this proof-of-concept can be expanded to provide a two-tone output with spline modulation and multi-DAC synchronization.
|
|
Ultimately it will be the basis for the ARTIQ Sayma Smart Arbitrary Waveform Generator project. See https://github.com/m-labs/sayma and https://github.com/m-labs/artiq-hardware.
|
|
|
|
*Features*:
|
|
|
|
* up to 4 channels
|
|
* up to 500 MHz data rate per channel (KC705 limitation)
|
|
* up to 8x interpolation to 2.4 GHz DAC sample rate
|
|
* Real-time control over amplitude, frequency, phase of each channel through ARTIQ RTIO commands
|
|
* Full configurability of the AD9154 and AD9516 through SPI with ARTIQ kernel support
|
|
* All SPI registers and register bits exposed as human readable names
|
|
* Parametrized JESD204B core (also capable of operation with eight lanes)
|
|
* The code can be reconfigured. Possible example configurations are: support 2 channels at 1 GHz datarate, support 4 channels at 300 MHz data rate, no interpolation, and using mix mode to stress the second and third Nyquist zones (150-300 MHz and 300-450 MHz).
|
|
|
|
The hardware required to use the ARTIQ phaser branch is a KC705 with an AD9154-FMC-EBZ plugged into the HPC connector and a low-noise sample rate reference clock.
|
|
|
|
This work was supported by the Army Research Lab.
|
|
|
|
The code that was developed for this project is located in several repositories:
|
|
|
|
* In ARTIQ, the SAWG and Phaser code: https://github.com/m-labs/artiq/compare/phaser
|
|
* The CORDIC core has been reused from the PDQ2 gateware https://github.com/m-labs/pdq2
|
|
* The Migen/MiSoC JESD204B core: https://github.com/m-labs/jesd204b
|
|
|
|
|
|
Installation
|
|
------------
|
|
|
|
These installation instructions are a short form of those in the ARTIQ manual.
|
|
Please refer to and follow the ARTIQ manual for more details:
|
|
https://m-labs.hk/artiq/manual-release-2/index.html
|
|
|
|
* Set up a new conda environment and activate it.
|
|
* Install the standard ARTIQ runtime/install dependencies.
|
|
See ``conda/artiq/meta.yaml`` for a list.
|
|
They are all packaged as conda packages in ``m-labs/main``.
|
|
|
|
* Install the standard ARTIQ build dependencies.
|
|
They are all available as conda packages in m-labs/main or m-labs/dev for linux-64:
|
|
|
|
- migen =0.4
|
|
- misoc =0.4
|
|
- llvm-or1k =3.8
|
|
- rust-core-or1k
|
|
- cargo
|
|
- binutils-or1k-linux >=2.27
|
|
|
|
* Install a recent version of Vivado (tested and developed with 2016.2).
|
|
* Checkout the ARTIQ phaser branch and the JESD204B core: ::
|
|
|
|
mkdir ~/src
|
|
cd ~/src
|
|
git clone --recursive -b phaser https://github.com/m-labs/artiq.git
|
|
git clone https://github.com/m-labs/jesd204b.git
|
|
cd jesd204b
|
|
python setup.py develop
|
|
cd ../artiq
|
|
python setup.py develop
|
|
|
|
|
|
Setup
|
|
-----
|
|
|
|
* Setup the KC705 (jumpers, etc.) observing the ARTIQ manual.
|
|
VADJ does not need to be changed.
|
|
* On the AD9154-FMC-EBZ put jumpers:
|
|
|
|
- on XP1, between pin 5 and 6 (will keep the PIC in reset)
|
|
- on JP3 (will force output enable on FXLA108)
|
|
|
|
* Compile the ARTIQ Phaser bitstream, bios, and runtime (c.f. ARTIQ manual): ::
|
|
|
|
python -m artiq.gateware.targets.kc705 -H phaser --toolchain vivado
|
|
|
|
* Run the following OpenOCD command to flash the ARTIQ phaser design: ::
|
|
|
|
openocd -f board/kc705.cfg -c "init; jtagspi_init 0 bscan_spi_xc7k325t.bit; jtagspi_program misoc_phaser_kc705/gateware/top.bin 0x000000; jtagspi_program misoc_phaser_kc705/software/bios/bios.bin 0xaf0000; jtagspi_program misoc_phaser_kc705/software/runtime/runtime.fbi 0xb00000; xc7_program xc7.tap; exit"
|
|
|
|
The proxy bitstream ``bscan_spi_xc7k325t.bit`` can be found at https://github.com/jordens/bscan_spi_bitstreams or in any ARTIQ conda package for the KC705.
|
|
See the source code of ``artiq_flash.py`` from ARTIQ for more details.
|
|
|
|
If you are using the OpenOCD Conda package:
|
|
|
|
* locate the OpenOCD scripts directory with: ``python3 -c "import artiq.frontend.artiq_flash as af; print(af.scripts_path)"``
|
|
* add ``-s <scripts directory>`` to the OpenOCD command line.
|
|
|
|
* Refer to the ARTIQ documentation to configure an IP address and other settings for the transmitter device.
|
|
If the board was running stock ARTIQ before, the settings will be kept.
|
|
* A 300 MHz clock of roughly 10 dBm (0.2 to 3.4 V peak-to-peak into 50 Ohm) must be connected to the AD9154-FMC-EBZ J1.
|
|
The external RTIO clock, DAC deviceclock, FPGA deviceclock, and SYSREF are derived from this signal.
|
|
* An example device database, several status and test scripts are provided in ``artiq/examples/phaser/``. ::
|
|
|
|
cd artiq/examples/phaser
|
|
|
|
* Edit ``device_db.pyon`` to match the hostname or IP address of the core device.
|
|
* The ``startup_clock`` needs to be set to internal (``i``) for bootstrapping the clock distribution tree.
|
|
* Compile and flash the startup kernel in ``artiq/examples/phaser/startup_kernel.py``.
|
|
* Erase any possible idle kernels.
|
|
* Use ``ping`` and ``flterm`` to verify that the core device starts up and boots correctly.
|
|
|
|
Usage
|
|
-----
|
|
|
|
* After each boot, run the ``dac_setup.py`` experiment to establish the JESD204B links (``artiq_run repository/dac_setup.py``).
|
|
* Run ``artiq_run repository/ad9154_test_status.py`` to retrieve and print several status registers from the AD9154 DAC.
|
|
* Run ``artiq_run repository/ad9154_test_prbs.py`` to test the JESD204B PHY layer for bit errors. Reboot the core device afterwards.
|
|
* Run ``artiq_run repository/ad9154_test_stpl.py`` to executes a JESD204B short transport layer test.
|
|
* Run ``artiq_run repository/sawg.py`` for an example that sets up amplitudes, frequencies, and phases on all four DDS channels.
|
|
* Run ``artiq_run repository/demo.py`` for an example that exercises several different use cases of synchronized phase, amplitude, and frequency updates.
|
|
for an example that exercises several different use cases of synchronized phase, amplitude, and frequency updates.
|
|
* Implement your own experiments using the SAWG channels.
|
|
* Verify clock stability between the sample rate reference clock and the DAC outputs.
|
|
* Changes to the AD9154 configuration can also be performed at runtime in experiments.
|
|
See the example ``dac_setup.py``.
|
|
This can e.g. be used to enable and evaluate mix mode without having to change any other code (bitstream/bios/runtime/startup_kernel).
|