pdq: documentation

artiq/coredevice/pdq.py

@@ -11,6 +11,16 @@ _PDQ_SPI_CONFIG = (
 
 @portable
 def _PDQ_CMD(board, is_mem, adr, we):
+    """Pack PDQ command fields into command byte.
+
+    :param board: Board address, 0 to 15, with ``15 = 0xf`` denoting broadcast
+        to all boards connected.
+    :param is_mem: If ``1``, ``adr`` denote the address of the memory to access
+        (0 to 2). Otherwise ``adr`` denotes the register to access.
+    :param adr: Address of the register or memory to access.
+        (``_PDQ_ADR_CONFIG``, ``_PDQ_ADR_FRAME``, ``_PDQ_ADR_CRC``).
+    :param we: If ``1`` then write, otherwise read.
+    """
     return (adr << 0) | (is_mem << 2) | (board << 3) | (we << 7)
 
 
@@ -20,10 +30,21 @@ _PDQ_ADR_FRAME = 2
 
 
 class PDQ:
-    """
+    """PDQ smart arbitrary waveform generator stack.
+
+    Provides access to a stack of PDQ boards connected via SPI using PDQ
+    gateware version 3 or later.
+
+    The SPI bus is wired with ``CS_N`` from the core device connected to
+    ``F2 IN`` on the master PDQ, ``CLK`` connected to ``F3 IN``, ``MOSI``
+    connected to ``F4 IN`` and ``MISO`` (optionally) connected to ``F5 OUT``.
+    ``F1 TTL Input Trigger`` remains as waveform trigger input.
+    Due to hardware constraints, there can only be one board connected to the
+    core device's MISO line and therefore there can only be SPI readback
+    from one board at any time.
 
     :param spi_device: Name of the SPI bus this device is on.
-    :param chip_select: Value to drive on the chip select lines
+    :param chip_select: Value to drive on the chip select lines of the SPI bus
         during transactions.
     """
 
@@ -54,11 +75,26 @@ class PDQ:
 
     @kernel
     def write_reg(self, adr, data, board):
+        """Set a PDQ register.
+
+        :param adr: Address of the register (``_PDQ_ADR_CONFIG``,
+            ``_PDQ_ADR_FRAME``, ``_PDQ_ADR_CRC``).
+        :param data: Register data (8 bit).
+        :param board: Board to access, ``0xf`` to write to all boards.
+        """
         self.bus.write((_PDQ_CMD(board, 0, adr, 1) << 24) | (data << 16))
         delay_mu(self.bus.ref_period_mu)  # get to 20ns min cs high
 
     @kernel
     def read_reg(self, adr, board):
+        """Get a PDQ register.
+
+        :param adr: Address of the register (``_PDQ_ADR_CONFIG``,
+          ``_PDQ_ADR_FRAME``, ``_PDQ_ADR_CRC``).
+        :param board: Board to access, ``0xf`` to write to all boards.
+
+        :return: Register data (8 bit).
+        """
         self.bus.set_xfer(self.chip_select, 16, 8)
         self.bus.write(_PDQ_CMD(board, 0, adr, 0) << 24)
         delay_mu(self.bus.ref_period_mu)  # get to 20ns min cs high
@@ -69,32 +105,58 @@ class PDQ:
     @kernel
     def write_config(self, reset=0, clk2x=0, enable=1,
                      trigger=0, aux_miso=0, aux_dac=0b111, board=0xf):
+        """Set configuration register.
+
+        :param reset: Reset board (auto-clear).
+        :param clk2x: Enable clock double (100 MHz).
+        :param enable: Enable the reading and execution of waveform data from
+            memory.
+        :param trigger: Software trigger, logical OR with ``F1 TTL Input
+            Trigger``.
+        :param aux_miso: Use ``F5 OUT`` for ``MISO``. If ``0``, use the
+            masked logical OR of the DAC channels.
+        :param aux_dac: DAC channel mask to for AUX (``F5 OUT``) output.
+        :param board: Boards to address, ``0xf`` to write to all boards.
+        """
         config = ((reset << 0) | (clk2x << 1) | (enable << 2) |
                   (trigger << 3) | (aux_miso << 4) | (aux_dac << 5))
         self.write_reg(_PDQ_ADR_CONFIG, config, board)
 
     @kernel
     def read_config(self, board=0xf):
+        """Read configuration register."""
         return self.read_reg(_PDQ_ADR_CONFIG, board)
 
     @kernel
     def write_crc(self, crc, board=0xf):
+        """Write checksum register."""
         self.write_reg(_PDQ_ADR_CRC, crc, board)
 
     @kernel
     def read_crc(self, board=0xf):
+        """Read checksum register."""
         return self.read_reg(_PDQ_ADR_CRC, board)
 
     @kernel
     def write_frame(self, frame, board=0xf):
+        """Write frame selection register."""
         self.write_reg(_PDQ_ADR_FRAME, frame, board)
 
     @kernel
     def read_frame(self, board=0xf):
+        """Read frame selection register."""
         return self.read_reg(_PDQ_ADR_FRAME, board)
 
     @kernel
     def write_mem(self, mem, adr, data, board=0xf):  # FIXME: m-labs/artiq#714
+        """Write to DAC channel waveform data memory.
+
+        :param mem: DAC channel memory to access (0 to 2).
+        :param adr: Start address.
+        :param data: Memory data. List of 16 bit integers.
+        :param board: Board to access (0-15) with ``0xf = 15`` being broadcast
+            to all boards.
+        """
         self.bus.set_xfer(self.chip_select, 24, 0)
         self.bus.write((_PDQ_CMD(board, 1, mem, 1) << 24) |
                        ((adr & 0x00ff) << 16) | (adr & 0xff00))
@@ -108,6 +170,14 @@ class PDQ:
 
     @kernel
     def read_mem(self, mem, adr, data, board=0xf, buffer=8):
+        """Read from DAC channel waveform data memory.
+
+        :param mem: DAC channel memory to access (0 to 2).
+        :param adr: Start address.
+        :param data: Memory data. List of 16 bit integers.
+        :param board: Board to access (0-15) with ``0xf = 15`` being broadcast
+            to all boards.
+        """
         n = len(data)
         if not n:
             return